Dose calibrator linearity test: 99mTc versus 18F radioisotopes

Objective: The present study was aimed at evaluating the viability of replacing 18F with 99mTc in dose calibrator linearity testing. Materials and Methods: The test was performed with sources of 99mTc (62 GBq) and 18F (12 GBq) whose activities were measured up to values lower than 1 MBq. Ratios and deviations between experimental and theoretical 99mTc and 18F sources activities were calculated and subsequently compared. Results: Mean deviations between experimental and theoretical 99mTc and 18F sources activities were 0.56 (± 1.79)% and 0.92 (± 1.19)%, respectively. The mean ratio between activities indicated by the device for the 99mTc source as measured with the equipment pre-calibrated to measure 99mTc and 18F was 3.42 (± 0.06), and for the 18F source this ratio was 3.39 (± 0.05), values considered constant over the measurement time. Conclusion: The results of the linearity test using 99mTc were compatible with those obtained with the 18F source, indicating the viability of utilizing both radioisotopes in dose calibrator linearity testing. Such information in association with the high potential of radiation exposure and costs involved in 18F acquisition suggest 99mTc as the element of choice to perform dose calibrator linearity tests in centers that use 18F, without any detriment to the procedure as well as to the quality of the nuclear medicine service.

Estimation de l'impact économique de l'introduction d'un test diagnostique rapide pour le dépistage des MRSA au CHUV

Contexte : Parmi les infections nosocomiales, le Staphylocoque méticilline résistant (MRSA) est le germe pathogène le plus couramment identifié dans les hôpitaux du monde entier. La stratégie de contrôle des MRSA au CHUV implique le dépistage des patients à risque. Avec la méthode de dépistage par culture, le temps d'attente est de plusieurs jours. Ceci occasionne des problèmes dans la gestion des flux des patients, principalement à cause des mesures d'isolement. Pour réduire le temps d'attente, l'hôpital envisage d'utiliser une méthode de diagnostic rapide par "polymerase chain reaction" (PCR). Méthodologie : Les données concernant les dépistages réalisés, dans trois services durant l'année 2007, ont été utilisées. Le nombre de jours d'isolement a d'abord été déterminé par patient et par service. Ensuite une analyse des coûts a été effectuée afin d'évaluer la différence des coûts entre les deux méthodes pour chaque service. Résultats : Le principal impact économique de la méthode par PCR dépend principalement du nombre de jours d'isolements évités par rapport à la méthode de culture. Aux services de soins, l'analyse a été menée sur 192 dépistages. Quand la différence de jours d'isolement est de deux jours, le coût des dépistages diminue de plus de 12kCHF et le nombre de jours d'isolement diminue de 384 jours. Au centre interdisciplinaire des urgences, sur 96 dépistages, le gain potentiel avec la méthode PCR est de 6kCHF avec une diminution de 192 jours d'isolement. Aux soins intensifs adultes, la méthode de dépistage par PCR est la méthode la plus rentable avec une diminution des coûts entre 4KCHF et 20K CHF et une diminution des jours d'isolement entre 170 et 310. Pour les trois services analysés, les résultats montrent un rapport coût-efficacité favorable pour la méthode PCR lorsque la diminution des jours d'isolement est supérieure à 1.3 jour. Quand la différence de jours d'isolement est inférieure à 1.3, il faut tenir compte d'autres paramètres, comme le coût de matériel qui doit être supérieur à 45.5 CHF, et du nombre d'analyses par dépistage, qui doit être inférieur à 3, pour que la PCR reste l'alternative la plus intéressante. Conclusions : La méthode par PCR montre des avantages potentiels importants, tant économiques qu'organisationnels qui limitent ou diminuent les contraintes liées à la stratégie de contrôle des MRSA au CHUV. [Auteure, p. 3]

Análisis del «perfil» de estudiantes de Enfermería mediante el test de Cattel

Conocer cuál es la personalidad de aquellos que acceden a nuestras Escuelas y que en pocos años se convertirán en futuros profesionales de Enfermería, ha sido el objetivo de un estudio llevado a cabo por la Comisión de Docencia de la E.U.E. de Barcelona. En él se realiza un análisis comparativo de los perfiles de personalidad de los estudiantes admitidos en la E.U.E. de Barcelona y los candidatos pre-inscritos en dicha escuela en 1983, frente a estudiantes de Enfermería americanas y británicas y los candidatos a estudiantes de Medicina de la Universidad de Navarra.

Determination of compression behaviour of coating layer

The strength properties of paper coating layer are very important in converting and printing operations. Too great or low strength of the coating can affect several problems in printing. One of the problems caused by the strength of coating is the cracking at the fold. After printing the paper is folded to final form and the pages are stapled together. In folding the paper coating can crack causing aesthetic damage over printed image or in the worst case the centre sheet can fall off in stapling. When folding the paper other side undergoes tensile stresses and the other side compressive stresses. If the difference between these stresses is too high, the coating can crack on the folding. To better predict and prevent cracking at the fold it is good to know the strength properties of coating layer. It has measured earlier the tensile strength of coating layer but not the compressive strength. In this study it was tried to find some way to measure the compressive strength of the coating layer and investigate how different coatings behave in compression. It was used the short span crush test, which is used to measure the in-plane compressive strength of paperboards, to measure the compressive strength of the coating layer. In this method the free span of the specimen is very small which prevent buckling. It was measured the compressive strength of free coating films as well as coated paper. It was also measured the tensile strength and the Bendtsen air permeance of the coating film. The results showed that the shape of pigment has a great effect to the strength of coating. Platy pigment gave much better strength than round or needle-like pigment. On the other hand calcined kaolin, which is also platy but the particles are aggregated, decreased the strength substantially. The difference in the strength can be explained with packing of the particles which is affecting to the porosity and thus to the strength. The platy kaolin packs up much better than others and creates less porous structure. The results also showed that the binder properties have a great effect to the compressive strength of coating layer. The amount of latex and the glass transition temperature, Tg, affect to the strength. As the amount of latex is increasing, the strength of coating is increasing also. Larger amount of latex is binding the pigment particles better together and decreasing the porosity. Compressive strength was increasing when the Tg was increasing because the hard latex gives a stiffer and less elastic film than soft latex.

Methods to test gas tightness of packages

One of the primary goals for food packages is to protect food against harmful environment, especially oxygen and moisture. The gas transmission rate is the total gas transport through the package, both by permeation through the package material and by leakage through pinholes and cracks. The shelf life of a product can be extended, if the food is stored in a gas tight package. Thus there is a need to test gas tightness of packages. There are several tightness testing methods, and they can be broadly divided into destructive and nondestructive methods. One of the most sensitive methods to detect leaks is by using a non destructive tracer gas technique. Carbon dioxide, helium and hydrogen are the most commonly used tracer gases. Hydrogen is the lightest and the smallest of all gases, which allows it to escape rapidly from the leak areas. The low background concentration of H2 in air (0.5 ppm) enables sensitive leak detection. With a hydrogen leak detector it is also possible to locate leaks. That is not possible with many other tightness testing methods. The experimental work has been focused on investigating the factors which affect the measurement results with the H2leak detector. Also reasons for false results were searched to avoid them in upcoming measurements. From the results of these experiments, the appropriate measurement practice was created in order to have correct and repeatable results. The most important thing for good measurement results is to keep the probe of the detector tightly against the leak. Because of its high diffusion rate, the HZ concentration decreases quickly if holding the probe further away from the leak area and thus the measured H2 leaks would be incorrect and small leaks could be undetected. In the experimental part hydrogen, oxygen and water vapour transmissions through laser beam reference holes (diameters 1 100 μm) were also measured and compared. With the H2 leak detector it was possible to detect even a leakage through 1 μm (diameter) within a few seconds. Water vapour did not penetrate even the largest reference hole (100 μm), even at tropical conditions (38 °C, 90 % RH), whereas some O2 transmission occurred through the reference holes larger than 5 μm. Thus water vapour transmission does not have a significant effect on food deterioration, if the diameter of the leak is less than 100 μm, but small leaks (5 100 μm) are more harmful for the food products, which are sensitive to oxidation.

Sustainability of EU fiscal policies. A panel test

The fiscal policy rule implicit in the Stability and Growth Pact, has been rationalised as a way to ensure that national fiscal policies remain sustainable within the EU, thereby endorsing the independence of the ECB. We empirically examine the sustainability of European fiscal policies over the period 1970-2001. The intertemporal government budget constraint provides a test based on the cointegration relation between government revenues, expenditures and interest payments. Sustainability is analysed at both the national level and for a European panel. Results show that European fiscal policy has been sustainable overall, yet national experiences differ considerably.

Evaluación de la estructura porosa de los materiales MCM-22, MCM-36 e ITQ-2 empleando el test catalitico del n-decano

The void structure of zeolites MCM-22, MCM-36 and ITQ-2 were discussed on the bases of catalytic reaction tests. The hydromerization of n-decane on bifunctional Pt/Zeolite Catalysts have been used as model reactions. Beta and ZSM-5 zeolites were used for comparison. It is concluded that all materials show features of 10MR zeolites and have also pores bigger than 12MR in this order MCM-22

Sexual foraging segregation in South American sea lions increases during the pre-breeding period in the La Plata River plume

Stable carbon and nitrogen isotopes in skin and bone of South American sea lions from Brazil and Uruguay were analysed to test the hypothesis that trophic overlap between the sexes is lower during the pre-breeding season than throughout the rest of the year. The isotopic values of skin and bone were used to infer the trophic relationships between the sexes during the pre-breeding period and year round, respectively. Prey species were also analysed to establish a baseline necessary for interpreting the stable isotope ratios of skin and bone. Standard ellipse areas, estimated using Bayesian inference in the SIBER routine of the SIAR package in R, suggested that males and females used a wide diversity of foraging strategies throughout the year and that no differences existed between the sexes. However, the diversity of foraging strategies was largely reduced during the pre-breeding period, with all the individuals of each sex adopting similar strategies, but with the two sexes differing considerably in stable isotope values and the ellipse areas of males and females not overlapping at all. Nevertheless, the results revealed a general increase in the consumption of pelagic prey by both sexes during the pre-breeding period. The progressive crowding of individuals in the areas surrounding the breeding rookeries during the pre-breeding period could lead to an increase in the local population density, which could explain the above reported changes.

Program hosting in communications environment with Reactor and thread pool approach

In this thesis concurrent communication event handling is implemented using thread pool approach. Concurrent events are handled with a Reactor design pattern and multithreading is implemented using a Leader/Followers design pattern. Main focus is to evaluate behaviour of implemented model by different numbers of concurrent connections and amount of used threads. Furthermore, model feasibility in a PeerHood middleware is evaluated. Implemented model is evaluated with created test environment which enables concurrent message sending from multiple connections to the system under test. Messages round trip times are measured in the tester application. In the evaluation processing delay into system is simulated and influence of delay to the average round trip time is analysed.

Dissolution test for glibenclamide tablets

The aim of this work is to develop and validate a dissolution test for glibenclamide tablets. Optimal conditions to carry out the dissolution test are 500 mL of phosphate buffer at pH 8.0, paddles at 75 rpm stirring speed, time test set to 60 min and using equipment with six vessels. The derivative UV spectrophotometric method for determination of glibenclamide released was developed, validated and compared with the HPLC method. The UVDS method presents linearity (r² = 0.9999) in the concentration range of 5-14 µg/mL. Precision and recoveries were 0.42% and 100.25%, respectively. The method was applied to three products commercially available on the Brazilian market.