Estudo de viabilidade técnica e econômica da utilização de geração diesel no horário de ponta

Given the current energy crisis experienced in our country with the lack of rain in some areas, the energy distributors were forced to resort to thermal power plants to complement their energy production; raising the cost of electricity generation, they have been forced to repass this value to the customers through the Tariff Flags. Concerned about a substantial increase in their electric bill, some consumers were forced to look for alternatives so that their results are not affected. The use of diesel generation at peak hours is a relatively simple and inexpensive alternative that has been widely used for several industrial, commercial and service customers. In this present work, we conducted a feasibility study of the use of diesel generators at peak hours in a medium-sized hospital, calculating the depreciation period for the investment through savings in electricity bills

Comparative degradation of ZnO- and SnO(2)-based polycrystalline non-ohmic devices by current pulse stress

The degradation behaviour of SnO(2)-based varistors (SCNCr) due to current pulses (8/20 mu s) is reported here for the first time in comparison with the ZnO-based commercial varistors (ZnO). Puncturing and/or cracking failures were observed in ZnO-based varistors possessing inferior thermo-mechanical properties in comparison with that found in a SCNCr system free of failures. Both systems presented electric degradation related to the increase in the leakage current and decrease in the electric breakdown field, non-linear coefficient and average value of the potential barrier height. However, it was found that a more severe degradation occurred in the ZnO-based varistors concerning their non-ohmic behaviour, while in the SCNCr system, a strong non-ohmic behaviour remained after the degradation. These results indicate that the degradation in the metal oxide varistors is controlled by a defect diffusion process whose rate depends on the mobility, the concentration of meta-stable defects and the amount of electrically active interfaces. The improved behaviour of the SCNCr system is then inferred to be associated with the higher amount of electrically active interfaces (85%) and to a higher energy necessary to activate the diffusion of the specific defects.

AcMus: an Open, Integrated Platform for Room Acoustics Research

This article describes the design, implementation, and experiences with AcMus, an open and integrated software platform for room acoustics research, which comprises tools for measurement, analysis, and simulation of rooms for music listening and production. Through use of affordable hardware, such as laptops, consumer audio interfaces and microphones, the software allows evaluation of relevant acoustical parameters with stable and consistent results, thus providing valuable information in the diagnosis of acoustical problems, as well as the possibility of simulating modifications in the room through analytical models. The system is open-source and based on a flexible and extensible Java plug-in framework, allowing for cross-platform portability, accessibility and experimentation, thus fostering collaboration of users, developers and researchers in the field of room acoustics.

Numerical analysis of control surface effects on AUV

Computational fluid dynamics, CFD, is becoming an essential tool in the prediction of the hydrodynamic efforts and flow characteristics of underwater vehicles for manoeuvring studies. However, when applied to the manoeuvrability of autonomous underwater vehicles, AUVs, most studies have focused on the de- termination of static coefficients without considering the effects of the vehicle control surface deflection. This paper analyses the hydrodynamic efforts generated on an AUV considering the combined effects of the control surface deflection and the angle of attack using CFD software based on the Reynolds-averaged Navier–Stokes formulations. The CFD simulations are also independently conducted for the AUV bare hull and control surface to better identify their individual and interference efforts and to validate the simulations by comparing the experimental results obtained in a towing tank. Several simulations of the bare hull case were conducted to select the k –ω SST turbulent model with the viscosity approach that best predicts its hydrodynamic efforts. Mesh sensitivity analyses were conducted for all simulations. For the flow around the control surfaces, the CFD results were analysed according to two different methodologies, standard and nonlinear. The nonlinear regression methodology provides better results than the standard methodology does for predicting the stall at the control surface. The flow simulations have shown that the occurrence of the control surface stall depends on a linear relationship between the angle of attack and the control surface deflection. This type of information can be used in designing the vehicle’s autopilot system.

Optische Spektroskopie an Fermium (Z=100)

Im Rahmen der vorliegenden Arbeit wurde erstmals Laser-Atomspektroskopie an einem Element durchgeführt, für das bisher keine atomaren Niveaus bekannt waren. Die Experimente wurden am Element Fermium mit der Ordnungszahl Z=100 mit der Resonanzionisationsspektroskopie (RIS) in einer Puffergaszelle durchgeführt. Verwendet wurde das Isotop 255Fm mit einer Halbwertszeit von 20.1 h, das im Hochflusskernreaktor des ORNL, Oak Ridge, USA, hergestellt wurde. Die von einem elektrochemischen Filament in das Argon-Puffergas bei einer Temperatur von 960(20)°C abgedampften Fm-Atome wurden mit Lasern in einem Zweistufenprozess resonant ionisiert. Dazu wurde das Licht eines Excimerlaser gepumpten Farbstofflasers für den ersten Anregungsschritt um die Wellenlänge 400 nm durchgestimmt. Ein Teil des Excimer (XeF) Laser Pumplichtes mit den Wellenlänge 351/353 nm wurde für die nicht-resonante Ionisation verwendet. Die Ionen wurden mit Hilfe elektrischer Felder aus der optischen Zelle extrahiert und nach einem Quadrupol Massenfilter mit einem Channeltron-Detektor massenselektiv nachgewiesen. Trotz der geringen Probenmenge von 2.7 x 10^10 eingesetzten Atomen wurden zwei atomare Resonanzen bei Energien von 25099.8(2) cm-1 und 25111.8(2) cm-1 gefunden und das Sättigungsverhalten dieser Linien gemessen. Es wurde ein theoretisches Modell entwickelt, dass sowohl das spektrale Profil der sättigungsverbreiterten Linien als auch die Sättigungskurven beschreibt. Durch Anpassung an die Messdaten konnten die partiellen Übergangsraten in den 3H6 Grundzustand Aki=3.6(7) x 10^6/s und Aki=3.6(6) x 10^6/s bestimmt werden. Der Vergleich der Niveauenergien und Übergangsraten mit Multikonfigurations Dirac-Fock Rechnungen legt die spektroskopische Klassifizierung der beobachteten Niveaus als 5f12 7s7p 5I6 und 5G6 Terme nahe. Weiterhin wurde ein Übergang bei 25740 cm-1 gefunden, der aufgrund der beobachteten Linienbreite von 1000 GHz als Rydbergzustand Zustand mit der Niveauenergie 51480 cm-1 interpretiert wurde und über einen Zweiphotonen Prozess angeregt werden kann. Basierend auf dieser Annahme wurde die Obergrenze für die Ionisationsenergie IP = 52140 cm-1 = 6.5 eV abgeschätzt. In den Messungen wurden Verschiebungen in den Zeitverteilungsspektren zwischen den mono-atomaren Ionen Fm+ und Cf+ und dem Molekül-Ion UO+ festgestellt und auf Driftzeitunterschiede im elektrischen Feld der gasgefüllten optischen Zelle zurückgeführt. Unter einfachen Modellannahmen wurde daraus auf die relativen Unterschiede Delta_r(Fm+,Cf+)/r(Cf+) ˜ -0.2 % und Delta_r(UO+,Cf+)/r(Cf+) ˜ 20 % in den Ionenradien geschlossen. Über die Bestimmung der Abnahme der Fm-a Aktivität des Filamentes auf der einen Seite und die Messung der Resonanzzählrate auf der anderen Seite, wurde die Nachweiseffizienz der Apparatur zu 4.5(3) x 10^-4 bestimmt. Die Nachweisapparatur wurde mit dem Ziel weiterentwickelt, Laserspektroskopie am Isotop 251Fm durchzuführen, das über die Reaktion 249Cf(a,2n)251Fm direkt in der optischen Zelle erzeugt werden soll. Das Verfahren wurde am chemischen Homolog Erbium getestet. Dabei wurde das Isotop 163Er über die Reaktion 161Dy(a,2n)163Er erzeugt und nach Resonanzionisation nachgewiesen. Die Nachweiseffizienz der Methode wurde zu 1 x 10^-4 bestimmt.

An alternative blocking layer for titanium dioxide (TiO 2) solar cell applications

In hybrid organic solar cells a blocking layer between transparent electrode and nanocrystalline titania particles is essential to prevent short-circuiting and current loss through recombination at the electrode interface. Here the preparation of a uniform hybrid blocking layer which is composed of conducting titania nanoparticles embedded in an insulating polymer derived ceramic is presented. This blocking layer is prepared by sol-gel chemistry where an amphiphilic block copolymer is used as a templating agent. A novel poly(dimethylsiloxane) containing amphiphilic block copolymer poly(ethyleneglycol)methylethermethacrylate-block-poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate has been synthesized to act as the templating agent. Plasma treatment uncovered titania surface from any polymer. Annealing at 450°C under nitrogen resulted in anatase titania with polymer derived silicon oxycarbide ceramic. Electrical characterization by conductive scanning probe microscopy experiments revealed a percolating titania network separated by an insulating ceramic matrix. Scanning Kelvin probe force microscopy showed predominant presence of titania particles on the surface creating a large surface area for dye absorption. The uniformity of the percolating structures was proven by microbeam grazing incidence small angle x-ray scattering. First applications in hybrid organic solar cells in comparison with conventional titanium dioxide blocking layer containing devices revealed 15 fold increases in corresponding efficiencies. Poly(dimethylsiloxane)-block-poly(ethyleneglycol)methylethermethacrylate and poly(ethyleneoxide)-poly(dimethylsiloxane)methylmethacrylate diblock copolymers were also synthesized. Their titania nanocomposite films were compared with the integrated blocking layer. Liner poly(ethyleneoxide) containing diblock copolymer resulted in highly ordered foam like structures. The effect of heating temperature rise to 600°C and 1000°C on titania morphology was investigated by scanning electron and force microscopy and x-ray scattering. Sol-gel contents, hydrochloric acid, titania precursor and amphiphilic triblock copolymer were altered to see their effect on titania morphology. Increase in block copolymer content resulted in titania particles of diameter 15-20 nm.

Nonlinear constrained and saturated control of power electronics and electromechanical systems

Power electronic converters are extensively adopted for the solution of timely issues, such as power quality improvement in industrial plants, energy management in hybrid electrical systems, and control of electrical generators for renewables. Beside nonlinearity, this systems are typically characterized by hard constraints on the control inputs, and sometimes the state variables. In this respect, control laws able to handle input saturation are crucial to formally characterize the systems stability and performance properties. From a practical viewpoint, a proper saturation management allows to extend the systems transient and steady-state operating ranges, improving their reliability and availability. The main topic of this thesis concern saturated control methodologies, based on modern approaches, applied to power electronics and electromechanical systems. The pursued objective is to provide formal results under any saturation scenario, overcoming the drawbacks of the classic solution commonly applied to cope with saturation of power converters, and enhancing performance. For this purpose two main approaches are exploited and extended to deal with power electronic applications: modern anti-windup strategies, providing formal results and systematic design rules for the anti-windup compensator, devoted to handle control saturation, and “one step” saturated feedback design techniques, relying on a suitable characterization of the saturation nonlinearity and less conservative extensions of standard absolute stability theory results. The first part of the thesis is devoted to present and develop a novel general anti-windup scheme, which is then specifically applied to a class of power converters adopted for power quality enhancement in industrial plants. In the second part a polytopic differential inclusion representation of saturation nonlinearity is presented and extended to deal with a class of multiple input power converters, used to manage hybrid electrical energy sources. The third part regards adaptive observers design for robust estimation of the parameters required for high performance control of power systems.

Self assembled materials for solar cell application

In der vorliegenden Arbeit wurden Materialien und Aufbauten für Hybrid Solarzellen entwickelt und erforscht. rnDer Vergleich zweier bekannter Lochleitermaterialien für Solarzellen in einfachen Blend-Systemen brachte sowohl Einsicht zur unterschiedlichen Eignung der Materialien für optoelektronische Bauelemente als auch neue Erkenntnisse in Bereichen der Langzeitstabilität und Luftempfindlichkeit beider Materialien.rnWeiterhin wurde eine Methode entwickelt, um Hybrid Solarzelle auf möglichst unkomplizierte Weise aus kostengünstigen Materialien darzustellen. Die „Eintopf“-Synthese ermöglicht die unkomplizierte Darstellung eines funktionalen Hybridmaterials für die optoelektronische Anwendung. Mithilfe eines neu entwickelten amphiphilen Blockcopolymers, das als funktionelles Templat eingesetzt wurde, konnten mit einem TiO2-Precursor in einem Sol-Gel Ansatz verschiedene selbstorganisierte Morphologien des Hybridmaterials erhalten werden. Verschiedene Morphologien wurden auf ihre Eignung in Hybrid Solarzellen untersucht. Ob und warum die Morphologie des Hybridsystems die Effizienz der Solarzelle beeinflusst, konnte verdeutlicht werden. Mit der Weiterentwicklung der „Eintopf“-Synthese, durch den Austausch des TiO2-Precursors, konnte die Solarzelleneffizienz von 0.15 auf 0.4 % gesteigert werden. Weiterhin konnte die Übertragbarkeit des Systems durch den erfolgreichen Austausch des Halbleiters TiO¬2 mit ZnO bewiesen werden.rn

Electrical scanning probe microscopy on organic optoelectronic structures

In the field of organic optoelectronics, the nanoscale structure of the materials has huge im-pact on the device performance. Here, scanning force microscopy (SFM) techniques become increasingly important. In addition to topographic information, various surface properties can be recorded on a nanometer length scale, such as electrical conductivity (conductive scanning force microscopy, C-SFM) and surface potential (Kelvin probe force microscopy, KPFM).rnrnIn the context of this work, the electrical SFM modes were applied to study the interplay be-tween morphology and electrical properties in hybrid optoelectronic structures, developed in the group of Prof. J. Gutmann (MPI-P Mainz). In particular, I investigated the working prin-ciple of a novel integrated electron blocking layer system. A structure of electrically conduct-ing pathways along crystalline TiO2 particles in an insulating matrix of a polymer derived ceramic was found and insulating defect structures could be identified. In order to get insights into the internal structure of a device I investigated a working hybrid solar cell by preparing a cross cut with focused ion beam polishing. With C-SFM, the functional layers could be identified and the charge transport properties of the novel active layer composite material could be studied. rnrnIn C-SFM, soft surfaces can be permanently damaged by (i) tip induced forces, (ii) high elec-tric fields and (iii) high current densities close to the SFM-tip. Thus, an alternative operation based on torsion mode topography imaging in combination with current mapping was intro-duced. In torsion mode, the SFM-tip vibrates laterally and in close proximity to the sample surface. Thus, an electrical contact between tip and sample can be established. In a series of reference experiments on standard surfaces, the working mechanism of scanning conductive torsion mode microscopy (SCTMM) was investigated. Moreover, I studied samples covered with free standing semiconducting polymer nano-pillars that were developed in the group of Dr. P. Theato (University Mainz). The application of SCTMM allowed non-destructive imag-ing of the flexible surface at high resolution while measuring the conductance on individual pillarsrnrnIn order to study light induced electrical effects on the level of single nanostructures, a new SFM setup was built. It is equipped with a laser sample illumination and placed in inert at-mosphere. With this photoelectric SFM, I investigated the light induced response in function-alized nanorods that were developed in the group of Prof. R. Zentel (University Mainz). A block-copolymer containing an anchor block and dye moiety and a semiconducting conju-gated polymer moiety was synthesized and covalently bound to ZnO nanorods. This system forms an electron donor/acceptor interface and can thus be seen as a model system of a solar cell on the nanoscale. With a KPFM study on the illuminated samples, the light induced charge separation between the nanorod and the polymeric corona could not only be visualized, but also quantified.rnrnThe results demonstrate that electrical scanning force microscopy can study fundamental processes in nanostructures and give invaluable feedback to the synthetic chemists for the optimization of functional nanomaterials.rn

Differential expression analysis for sequence count data via mixtures of negative binomials

The recent advent of Next-generation sequencing technologies has revolutionized the way of analyzing the genome. This innovation allows to get deeper information at a lower cost and in less time, and provides data that are discrete measurements. One of the most important applications with these data is the differential analysis, that is investigating if one gene exhibit a different expression level in correspondence of two (or more) biological conditions (such as disease states, treatments received and so on). As for the statistical analysis, the final aim will be statistical testing and for modeling these data the Negative Binomial distribution is considered the most adequate one especially because it allows for "over dispersion". However, the estimation of the dispersion parameter is a very delicate issue because few information are usually available for estimating it. Many strategies have been proposed, but they often result in procedures based on plug-in estimates, and in this thesis we show that this discrepancy between the estimation and the testing framework can lead to uncontrolled first-type errors. We propose a mixture model that allows each gene to share information with other genes that exhibit similar variability. Afterwards, three consistent statistical tests are developed for differential expression analysis. We show that the proposed method improves the sensitivity of detecting differentially expressed genes with respect to the common procedures, since it is the best one in reaching the nominal value for the first-type error, while keeping elevate power. The method is finally illustrated on prostate cancer RNA-seq data.

Ein inverses Rückstreuproblem der elektrischen Impedanztomographie

Die vorliegende Arbeit untersucht das inverse Hindernisproblem der zweidimensionalen elektrischen Impedanztomographie (EIT) mit Rückstreudaten. Wir präsentieren und analysieren das mathematische Modell für Rückstreudaten, diskutieren das inverse Problem für einen einzelnen isolierenden oder perfekt leitenden Einschluss und stellen zwei Rekonstruktionsverfahren für das inverse Hindernisproblem mit Rückstreudaten vor. Ziel des inversen Hindernisproblems der EIT ist es, Inhomogenitäten (sogenannte Einschlüsse) der elektrischen Leitfähigkeit eines Körpers aus Strom-Spannungs-Messungen an der Körperoberfläche zu identifizieren. Für die Messung von Rückstreudaten ist dafür nur ein Paar aus an der Körperoberfläche nahe zueinander angebrachten Elektroden nötig, das zur Datenerfassung auf der Oberfläche entlang bewegt wird. Wir stellen ein mathematisches Modell für Rückstreudaten vor und zeigen, dass Rückstreudaten die Randwerte einer außerhalb der Einschlüsse holomorphen Funktion sind. Auf dieser Grundlage entwickeln wir das Konzept des konvexen Rückstreuträgers: Der konvexe Rückstreuträger ist eine Teilmenge der konvexen Hülle der Einschlüsse und kann daher zu deren Auffindung dienen. Wir stellen einen Algorithmus zur Berechnung des konvexen Rückstreuträgers vor und demonstrieren ihn an numerischen Beispielen. Ferner zeigen wir, dass ein einzelner isolierender Einschluss anhand seiner Rückstreudaten eindeutig identifizierbar ist. Der Beweis dazu beruht auf dem Riemann'schen Abbildungssatz für zweifach zusammenhängende Gebiete und dient als Grundlage für einen Rekonstruktionsalgorithmus, dessen Leistungsfähigkeit wir an verschiedenen Beispielen demonstrieren. Ein perfekt leitender Einschluss ist hingegen nicht immer aus seinen Rückstreudaten rekonstruierbar. Wir diskutieren, in welchen Fällen die eindeutige Identifizierung fehlschlägt und zeigen Beispiele für unterschiedliche perfekt leitende Einschlüsse mit gleichen Rückstreudaten.

Sviluppo del cammino durante la crescita: Confronto tra variabilità segmentale e variabilità del centro di massa

In letteratura è noto che la variabilità cinematica dei bambini durante il cammino è molto maggiore se confrontata con quella di soggetti adulti. Ciò rende difficile definire lo sviluppo del cammino basandosi sull'analisi di angoli articolari. In questo lavoro è stata valutata la traiettoria del centro di massa come possibile fattore caratterizzante la maturazione del cammino durante la crescita: l’ipotesi è che questa risulti, nei bambini, più ripetibile rispetto al pattern degli angoli articolari. È stata analizzata la cinematica del cammino di soggetti appartenenti a tre fasce di età differenti (4 anni, 6 anni, giovani adulti), mediante un sistema di stereofotogrammetria e marker riflettenti (protocollo Plug-in Gait). Lo studio è stato condotto avvalendosi di software per l’acquisizione, l’elaborazione (BTS Smart-DX) e l’analisi statistica (SPM1D) dei parametri d’interesse. La variabilità è stata analizzata secondo tre diverse modalità (Inter-subject, Intra-subject, Inter-test). È stato osservato un trend simile in termini di variabilità del centro di massa tra bambini e adulti. La variabilità cinematica degli angoli articolari è invece risultata più alta nei bambini, in maniera significativa per tutte e tre le modalità citate. L’ipotesi è stata confermata per i soggetti che hanno preso parte allo studio: i bambini, pur avendo raggiunto un relativo sviluppo del cammino, presentano una variabilità segmentale maggiore di quella degli adulti, mentre la variabilità della traiettoria del centro di massa è risultata essere simile a quella dei soggetti maturi.

Genetics of male nuptial colour divergence between sympatric sister species of a Lake Victoria cichlid fish

The hypothesis of sympatric speciation by sexual selection has been contentious. Several recent theoretical models of sympatric speciation by disruptive sexual selection were tailored to apply to African cichlids. Most of this work concludes that the genetic architecture of female preference and male trait is a key determinant of the likelihood of disruptive sexual selection to result in speciation. We investigated the genetic architecture controlling male nuptial colouration in a sympatric sibling species pair of cichlid fish from Lake Victoria, which differ conspicuously in male colouration and female mating preferences for these. We estimated that the difference between the species in male nuptial red colouration is controlled by a minimum number of two to four genes with significant epistasis and dominance effects. Yellow colouration appears to be controlled by one gene with complete dominance. The two colours appear to be epistatically linked. Knowledge on how male colouration segregates in hybrid generations and on the number of genes controlling differences between species can help us assess whether assumptions made in simulation models of sympatric speciation by sexual selection are realistic. In the particular case of the two sister species that we studied a small number of genes causing major differences in male colouration may have facilitated the divergence in male colouration associated with speciation.

An efficient framework for photon Monte Carlo treatment planning

Currently photon Monte Carlo treatment planning (MCTP) for a patient stored in the patient database of a treatment planning system (TPS) can usually only be performed using a cumbersome multi-step procedure where many user interactions are needed. This means automation is needed for usage in clinical routine. In addition, because of the long computing time in MCTP, optimization of the MC calculations is essential. For these purposes a new graphical user interface (GUI)-based photon MC environment has been developed resulting in a very flexible framework. By this means appropriate MC transport methods are assigned to different geometric regions by still benefiting from the features included in the TPS. In order to provide a flexible MC environment, the MC particle transport has been divided into different parts: the source, beam modifiers and the patient. The source part includes the phase-space source, source models and full MC transport through the treatment head. The beam modifier part consists of one module for each beam modifier. To simulate the radiation transport through each individual beam modifier, one out of three full MC transport codes can be selected independently. Additionally, for each beam modifier a simple or an exact geometry can be chosen. Thereby, different complexity levels of radiation transport are applied during the simulation. For the patient dose calculation, two different MC codes are available. A special plug-in in Eclipse providing all necessary information by means of Dicom streams was used to start the developed MC GUI. The implementation of this framework separates the MC transport from the geometry and the modules pass the particles in memory; hence, no files are used as the interface. The implementation is realized for 6 and 15 MV beams of a Varian Clinac 2300 C/D. Several applications demonstrate the usefulness of the framework. Apart from applications dealing with the beam modifiers, two patient cases are shown. Thereby, comparisons are performed between MC calculated dose distributions and those calculated by a pencil beam or the AAA algorithm. Interfacing this flexible and efficient MC environment with Eclipse allows a widespread use for all kinds of investigations from timing and benchmarking studies to clinical patient studies. Additionally, it is possible to add modules keeping the system highly flexible and efficient.

Spectroscopic properties of pyrene-containing DNA mimics

DNA mimics containing non-nucleosidic pyrene building blocks are described. The modified oligomers form stable hybrids, although a slight reduction in hybrid stability is observed in comparison to the unmodified DNA duplex. The nature of the interaction between the pyrene residues in single and double stranded oligomers is analyzed spectroscopically. Intra- and inter-strand stacking interactions of pyrenes are monitored by UV-absorbance as well as fluorescence spectroscopy. Excimer formation is observed in both single and double strands. In general, intrastrand excimers show fluorescence emission at shorter wavelengths (approx. 5-10 nm) than excimers formed by interstrand interactions. The existence of two different forms of excimers (intra- vs. interstrand) is also revealed in temperature dependent UV-absorbance spectra. (C) 2007 Elsevier Ltd. All rights reserved.