A neutron diffraction investigation of residual stresses in rail ends after severe deformation of rail surfaces

Insulated rail joints (IRJs) are a primary component of the rail track safety and signalling systems. Rails are supported by two fishplates which are fastened by bolts and nuts and, with the support of sleepers and track ballast, form an integrated assembly. IRJ failure can result from progressive defects, the propagation of which is influenced by residual stresses in the rail. Residual stresses change significantly during service due to the complex deformation and damage effects associated with wheel rolling, sliding and impact. IRJ failures can occur when metal flows over the insulated rail gap (typically 6-8 mm width), breaks the electrically isolated section of track and results in malfunction of the track signalling system. In this investigation, residual stress measurements were obtained from rail-ends which had undergone controlled amounts of surface plastic deformation using a full scale wheel-on-track simulation test rig. Results were compared with those obtained from similar investigations performed on rail ends associated with ex-service IRJs. Residual stresses were measured by neutron diffraction at the Australian Nuclear Science and Technology Organisation (ANSTO). Measurements with constant gauge volume 3x3x3 mm3 were carried in the central vertical plane on 5mm thick sliced rail samples cut by an electric discharge machine (EDM). Stress evolution at the rail ends was found to exhibit characteristics similar to those of the ex-service rails, with a compressive zone of 5mm deep that is counterbalanced by a tension zone beneath, extending to a depth of around 15mm. However, in contrast to the ex-service rails, the type of stress distribution in the test-rig deformed samples was apparently different due to the localization of load under the particular test conditions. In the latter, in contrast with clear stress evolution, there was no obvious evolution of d0. Since d0 reflects rather long-term accumulation of crystal lattice damage and microstructural changes due to service load, the loading history of the test rig samples has not reached the same level as the ex-service rails. It is concluded that the wheel-on-rail simulation rig provides the potential capability for testing the wheel-rail rolling contact conditions in rails, rail ends and insulated rail joints.

Academics and the new public intellectual

In this essay, we outline an emerging form of public intellectualism in the humanities sector of Australian higher education. We argue that debates over public intellectualism and its relation to the academy in Australia have largely been focused on the tension between polemics and politics. These debates have also tended to ignore or overlook policy drivers within the sector and alternative or new media sites of public intellectualism. Shifting the focus towards policy drivers in the knowledge economy—such as knowledge transfer and third-stream funding—and understanding the nature of the university as a public sphere in itself reveals a new economy of the public intellectual as a professional knowledge worker. This new economy, we argue, may well render obsolete many of the previous debates over public intellectualism in the humanities. However, we anticipate that it will generate new debates over the relationship between the individual and the institutional, and between the concepts of public profile and public role—debates that will affect, in particular, early career academics who are the inheritors of this new economy of the public intellectual.

Psychological predictors of injury among elite athletes

Objectives: To establish injury rates among a population of elite athletes, to provide normative data for psychological variables hypothesised to be predictive of sport injuries, and to establish relations between measures of mood, perceived life stress, and injury characteristics as a precursor to introducing a psychological intervention to ameliorate the injury problem. Methods: As part of annual screening procedures, athletes at the Queensland Academy of Sport report medical and psychological status. Data from 845 screenings (433 female and 412 male athletes) were reviewed. Population specific tables of normative data were established for the Brunel mood scale and the perceived stress scale. Results: About 67% of athletes were injured each year, and about 18% were injured at the time of screening. Fifty percent of variance in stress scores could be predicted from mood scores, especially for vigour, depression, and tension. Mood and stress scores collectively had significant utility in predicting injury characteristics. Injury status (current, healed, no injury) was correctly classified with 39% accuracy, and back pain with 48% accuracy. Among a subset of 233 uninjured athletes (116 female and 117 male), five mood dimensions (anger, confusion, fatigue, tension, depression) were significantly related to orthopaedic incidents over the preceding 12 months, with each mood dimension explaining 6–7% of the variance. No sex differences in these relations were found. Conclusions: The findings support suggestions that psychological measures have utility in predicting athletic injury, although the relatively modest explained variance highlights the need to also include underlying physiological indicators of allostatic load, such as stress hormones, in predictive models.

Molecular dynamics simulation of mechanical behavior of osteopontin-hydroxyapatite interfaces

Bone is characterized with an optimized combination of high stiffness and toughness. The understanding of bone nanomechanics is critical to the development of new artificial biological materials with unique properties. In this work, the mechanical characteristics of the interfaces between osteopontin (OPN, a noncollagenous protein in extrafibrillar protein matrix) and hydroxyapatite (HA, a mineral nanoplatelet in mineralized collagen fibrils) were investigated using molecular dynamics method. We found that the interfacial mechanical behaviour is governed by the electrostatic attraction between acidic amino acid residues in OPN and calcium in HA. Higher energy dissipation is associated with the OPN peptides with a higher number of acidic amino acid residues. When loading in the interface direction, new bonds between some acidic residues and HA surface are formed, resulting in a stick-slip type motion of OPN peptide on the HA surface and high interfacial energy dissipation. The formation of new bonds during loading is considered to be a key mechanism responsible for high fracture resistance observed in bone and other biological materials.

Provotypes: Teasing out tensions between industrial context and use context

What industrial organisations think people do and what they actually do are often two very different things. But exactly this tension can be a source of innovation: how can we give form to insights about what people do, to deliberately challenge industries' conceptions, and inspire new product and service development

Residual stresses in rail-ends from the in-service insulated rail joints using neutron diffraction

Insulated rail joints (IRJs) are an integral part of the rail track signaling system and pose significant maintenance and replacement costs due to their low and fluctuating service lives. Failure occurs mainly in rail head region, bolt- holes of fishplates and web-holes of the rails. Propagation of cracks is influenced by the evolution of internal residual stresses in rails during rail manufacturing (hot-rolling, roller-straightening, and head-hardening process), and during service, particularly in heavy rail haul freight systems where loads are high. In this investigation, rail head accumulated residual stresses were analysed using neutron diffraction at the Australian Nuclear Science and Technology Organisation (ANSTO). Two ex-service two head-hardened rail joints damaged under different loading were examined and results were compared with those obtained from an unused rail joint reference sample in order to differentiate the stresses developed during rail manufacturing and stresses accumulated during rail service. Neutron diffraction analyses were carried out on the samples in longitudinal, transverse and vertical directions, and on 5mm thick sliceed samples cut by Electric Discharge Machining (EDM). For the rail joints from the service line, irrespective of loading conditions and in-service times, results revealed similar depth profiles of stress distribution. Evolution of residual stress fields in rails due to service was also accompanied by evidence of larger material flow based on reflected light and scanning electron microscopy studies. Stress evolution in the vicinity of rail ends was characterised by a compressive layer, approximately 5 mm deep, and a tension zone located approximately 5- 15mm below the surfaces. A significant variation of d0 with depth near the top surface was detected and was attributed to decarburization in the top layer induced by cold work. Stress distributions observed in longitudinal slices of the two different deformed rail samples were found to be similar. For the undeformed rail, the stress distributions obtained could be attributed to variations associated with thermo-mechanical history of the rail.

Investigation on mechanical behaviour of AM60 magnesium alloys

Purpose: In this work, tension, impact, bend and fatigue tests were conducted in an AM60 magnesium alloy. The effects of environmental temperature and loading rates on impact and tension behavior of the alloy were also investigated. Design/methodology/approach: The tests were conducted using an Instron universal testing machine. The loading speed was changed from 1 mm/min to 300 mm/min to gain a better understanding of the effect of strain rate. To understand the failure behavior of this alloy at different environmental temperatures, Charpy impact test was conducted in a range of temperatures (-40~35°C). Plane strain fracture toughness (KIC) was evaluated using compact tension (CT) specimen. To gain a better understanding of the failure mechanisms, all fracture surfaces were observed using scanning electron microscopy (SEM). In addition, fatigue behavior of this alloy was estimated using tension test under tension-tension condition at 30 Hz. The stress amplitude was selected in the range of 20~50 MPa to obtain the S-N curve. Findings: The tensile test indicated that the mechanical properties were not sensitive to the strain rates applied (3.3x10-4~0.1) and the plastic deformation was dominated by twining mediated slip. The impact energy is not sensitive to the environmental temperature. The plane strain fracture toughness and fatigue limit were evaluated and the average values were 7.6 MPa.m1/2 and 25 MPa, respectively. Practical implications: Tested materials AM60 Mg alloy can be applied among others in automotive industry aerospace, communication and computer industry. Originality/value: Many investigations have been conducted to develop new Mg alloys with improved stiffness and ductility. On the other hand, relatively less attention has been paid to the failure mechanisms of Mg alloys, such as brittle fracture and fatigue, subjected to different environmental or loading conditions. In this work, tension, impact, bend and fatigue tests were conducted in an AM60 magnesium alloy.

Mechanism of the α-to-β phase transformation in the LaNi5–H2 system

High-energy synchrotron in situ X-ray powder diffraction has been used to elucidate the mechanism of the hydriding phase transformation in a LaNi5 model hydrogen storage intermetallic in real time. The transformation proceeds at 10 °C via the transient growth of an interfacial phase, the γ phase, with lattice parameters intermediate between those of the α (dilute solid solution) and β (concentrated hydride) phases. The γ phase forms to partially accommodate the 24% change in unit cell volume between the α and β phases during hydriding and dehydriding. The α, γ and β phases coexist at the nanoscopic level.

Tensile properties of a boron/nitrogen-doped carbon nanotube–graphene hybrid structure

Doping is an effective approach that allows for the intrinsic modification of the electrical and chemical properties of nanomaterials. Recently, a graphene and carbon nanotube hybrid structure (GNHS) has been reported, which extends the excellent properties of carbon-based materials to three dimensions. In this paper, we carried out a first-time investigation on the tensile properties of the hybrid structures with different dopants. It is found that with the presence of dopants, the hybrid structures usually exhibit lower yield strength, Young’s modulus, and earlier yielding compared to that of a pristine hybrid structure. For dopant concentrations below 2.5% no significant reduction of Young’s modulus or yield strength could be observed. For all considered samples, the failure is found to initiate at the region where the nanotubes and graphene sheets are connected. After failure, monatomic chains are normally observed around the failure region. Dangling graphene layers without the separation of a residual CNT wall are found to adhere to each other after failure with a distance of about 3.4 Å. This study provides a fundamental understanding of the tensile properties of the doped graphene–nanotube hybrid structures, which will benefit the design and also the applications of graphene-based hybrid materials.

ÉLET [LIFE]

Élet [pronounced air-let] is the Hungarian word for Life. The work is informed by the lyrics of six songs performed by French cover band Nouvelle Vague. Whilst Élet [Life] is created to be absorbed and interpreted openly by each individual, at the core of the choreography lies a desire to move forwards, to communicate – to be seen and heard. The work embraces aspects such as loneliness, joy and tension that we experience in our lives and relationships. As the movement opens out from these ideas, the physical shapes of our personal moments are infused with the elements of sound, colour and rhythm. A rich translation of personal movements through life.

Genetic technologies and the regulation of reproductive decision-making in Australia

This article provides a critical analysis of the current Australian regulatory landscape at the interface between genetics and reproductive decision- making. The authors argue that a comparative analysis with other countries and international law and a contextual examination of the way law regulates concepts such as disease and health, abnormality and normality is necessary before we can develop appropriate policy and legislative responses in this area. Specific genetic testing technologies are considered including prenatal genetic testing, preimplantation genetic diagnosis and inheritable genetic modification. An increasing number of members of the Australian community are using genetic testing technologies when they decide to have a baby. The authors argue that as concepts of disease and health vary among members of the community and the potential to test for traits other than illness increases, a new tension arises between an ethic of individual choice and a role for government in regulating reproductive decision-making.

Globalising the body : globalisation and reproductive rights

Globalisation is a phenomenon of the contemporary world. Everywhere around us there seem to be signs of the power of the forces of globalisation: in our media and popular culture; in our international linkages across continents through international travel and telecommunications; in our globalised trade; and with the global movement of people, a process which itself ranges from the movement of international tourists to the international movement of refugees and other displaced persons. The processes of globalisation seem to simultaneously unify and divide us. There is no doubt that we live in a globalised world and that we are connected to others in previously unimaginable ways by transportation, telecommunications and economics. Yet, while this global context increasingly links us to others, there is also a very real sense in which separation, difference and the local have also gained a new significance; we are locked in a tension between the universal and the particular that has come to typify contemporary society. This article explores the meanings of globalisation and this dynamic – or tension – between the universal and the particular in terms of its implications for the body and, in particular, its significance for women and their reproductive rights.

What is a good project manager? An Aristotelian perspective

The purpose of this paper is to take a critical look at the question “what is a competent project manager?” and bring some fresh added-value insights. This leads us to analyze the definitions, and assessment approaches of project manager competence. Three major standards as prescribed by PMI, IPMA, and GAPPS are considered for review from an attribute-based and performance-based approach and from a deontological and consequentialist ethics perspectives. Two fundamental tensions are identified: an ethical tension between the standards and the related competence assessment frameworks and a tension between attribute and performance-based approaches. Aristotelian ethical and practical philosophy is brought in to reconcile these differences. Considering ethics of character that rises beyond the normative deontological and consequentialist perspectives is suggested. Taking the mediating role of praxis and phrónêsis between theory and practice into consideration is advocated to resolve the tension between performance and attribute-based approaches to competence assessment.

Alterations in cervical muscle activity in functional and stressful tasks in female office workers with neck pain

This study determined differences between computer workers with varying levels of neck pain in terms of work stressors, employee strain, electromyography (EMG) amplitude and heart rate response to various tasks. Participants included 85 workers (33, no pain; 38, mild pain; 14, moderate pain) and 22 non-working controls. Work stressors evaluated were job demands, decision authority, and social support. Heart rate was recorded during three tasks: copy-typing, typing with superimposed stress and a colour word task. Measures included electromyography signals from the sternocleidomastoid (SCM), anterior scalene (AS), cervical extensor (CE) and upper trapezius (UT) muscles bilaterally. Results showed no difference between groups in work stressors or employee strain measures. Workers with and without pain had higher measured levels of EMG amplitude in SCM, AS and CE muscles during the tasks than controls (all P < 0.02). In workers with neck pain, the UT had difficulty in switching off on completion of tasks compared with controls and workers without pain. There was an increase in heart rate, perceived tension and pain and decrease in accuracy for all groups during the stressful tasks with symptomatic workers producing more typing errors than controls and workers without pain. These findings suggest an altered muscle recruitment pattern in the neck flexor and extensor muscles. Whether this is a consequence or source of the musculoskeletal disorder cannot be determined from this study. It is possible that workers currently without symptoms may be at risk of developing a musculoskeletal disorder.

Numerical investigation on stable crack growth in plane stress

Large deformation finite element analysis has been carried out to investigate the stress-strain fields ahead of a growing crack for compact tension .a=W D 0:5/ and three-point bend .a=W D 0:1 and 0:5/ specimens under plane stress condition. The crack growth is controlled by the experimental J -integral resistance curves measured by Sun et al. The results indicate that the distributions of opening stress, equivalent stress and equivalent strain ahead of a growing crack are not sensitive to specimen geometry. For both stationary and growing cracks, similar distributions of opening stress and triaxiality can be found along the ligament. During stable crack growth, the crack-tip opening displacement (CTOD) resistance curve and the cohesive fracture energy in the fracture process zone are independent of specimen geometry and may be suitable criteria for characterizing stable crack growth in plane stress.