Preparation and mass spectrometric study of egg yolk antibody (IgY) against rabies virus

Rabies virus was used as the antigen to immunize laying chickens. Anti-rabies virus immunoglobulin Y(IgY) was isolated from yolks of the eggs laid by these chickens using a two-step salt precipitation and one-step gel filtration protocol. The purified IgY was reduced with dithiothreitol, and heavy chains (HC) and light chains (LC) were obtained. In addition, the purified IgY was digested with pepsin and the fragment with specific antigen binding properties (Fab) was produced. Using matrix-assisted laser desorption/ionization mass spectrometry (MALDI-TOFMS), the average molecular weights of IgY, HC, LC, and Fab were determined as 167 250, 65 105, 18 660, and 45,359 Da, respectively. IgY has two structural differences compared with mammalian IgGs. First, the molecular weight of the heavy chain of IgY is larger than that of its mammalian counterpart, while the molecular weight of the light chain of IgY is smaller. Second, upon pepsin digestion, anti-rabies virus IgY is degraded into Feb, in contrast to mammalian IgG, which has been reported to be degraded into F(ab')(2) under the same conditions. Copyright (C) 2001 John Wiley & Sons, Ltd.

Polymerization of methyl methacrylate with organolanthanides as single-component catalysts

It was first found that Ind(2)Y(mu -Et)(2)AlEt2 and Ind(2)LnN(i-Pr)(2) (Ln = Y, Yb) exhibit extremely high catalytic activity in the polymerization of methyl methacrylate. The reactions can be carried out over a quite broad range of polymerization temperatures from -30 to 50 degreesC. PMMA with high molecular weight (7.8 x 10(-5)) and high isotacticity (94%) can be obtained by using Ind(2)Y(mu -Et)(2)AlEt2, and narrow molecular weight distribution (M-w/M-n < 1.5) can be obtained by using Ind(2)LnN(i-Pr)(2) (Ln = Y, Yb).

Polymerization of acrylonitrile with organolanthanides as single-component catalysts

Ind(2)Y(mu -Et)(2)AlEt2 and Ind(2)LnN(i-Pr)(2) (Ln = Y, Yb) were used as a single-component catalyst for the polymerization of acrylonitrile (AN) respectively. The regularity of polymerization of AN and stereoregularity of polyacrylonitrile (PAN) were also studied in both cases. Both catalysts can produce PAN with molecular weight from 10,000 to 30,000. In addition, the catalytic activity and molecular weights were increased by the addition of PhONa.

Binuclear lanthanide complexes as catalysts for the hydrolysis of double-stranded DNA

The efficient cleavage of plasmid DNA ( pCAT) by binuclear lanthanide complexes was investigated. At 37 degrees C and neutral pH, both Ho23+L and Er23+L promoted 100% conversion of supercoiled plasmid to the nicked circular form and linear form in 1 h. The corresponding saturation kinetics curve of cleavage of pCAT plasmid by binuclear lanthanide complexes showed the expected increase with catalyst concentration. (C) 1999 Elsevier Science S.A. All rights reserved.

Preparation of polymer-supported zirconocene catalysts and olefin polymerization

A novel polymer-supported metallocene catalyst with crosslinked poly(styrene-co-acrylamide) (PSAm) as the support has been prepared and characterized. The probability of long sequences of acrylamide (Am) in PSAm is still low even at an Am amount of 32.8 mol %, implying the relatively homogeneous distribution of Am. The infrared spectra of PSAm and the supported catalyst substantiate that an amide group in PSAm coordinates with methylaluminoxane through both oxygen and nitrogen atoms. Ethylene/alpha-octene copolymerization showed that the catalytic activity is not markedly affected by adding alpha-octene. C-13 NMR analysis of the ethylene/alpha-octene copolymer indicated that the composition distribution of the copolymer is uniform. (C) 1999 John Wiley & Sons, Inc.

Reactivity of Pt/Al2O3 and Pt/CeO2/Al2O3 catalysts for partial oxidation of methane to syngas

The ceria modified Pt/CeO2/Al2O3 and Pt/Al2O3 catalysts were studied in the partial oxidation of methane to syngas. The SEM, XRD, TPR and TPD techniques were used for the catalyst characterization. The addition of ceria could enhance the Pt dispersion and decrease the Pt crystallise size; the activity and selectivity of catalyst for partial oxidation were improved significantly, and the methane total oxidation was suppressed sharply. The ceria effect was also discussed in a detailed way.

Isobutane/butene alkylation over supported heteropoly acid catalysts: I. Influence of the structure of silica

Catalysts consisting of heteropoly acids (HPAs) supported on different silica and mesoporous molecular sieves have been prepared by impregnation and the sol-gel method, respectively, and their catalytic behavior in fixed-bed alkylation of isobutane with butene has been investigated. The activity, selectivity and stability of the supported-HPA catalysts could be correlated with the surface acidity of the catalysts, the structure of supports as well as the time on stream (TOS). In the fixed-bed reactor, the acidity of the heteropoly acid is favorable to the formation of dimerization products (C-8(=)); especially, the pore size of supports was seen to have an important effect on activity and product distribution of the catalysts. Contrary to the traditional solid-acid catalysts, the supported-HPA catalysts own an excellent stability for alkylation, which makes it possible for these supported catalysts to replace the liquid-acid catalysts used in industry.

A study of the effect of shell content on the mechanical properties of polycarbonate/poly(butyl acrylate)-cs-poly(methyl methacrylate) blends

The toughening effect of the shell content of a core-shell latex polymer poly(butyl acrylate) (PBA)-cs-poly(methyl methacrylate) (PMMA) on its blends with polycarbonate (PC) was studied. The changes of mechanical properties, morphology, and compatibility of the blends of PC/PBA-cs-PMMA with the change of the shell thickness of PBA-cs-PMMA were investigated. It is interesting to notice that mechanical properties of the blends are very sensitive to the shell thickness (i.e., shell content), and that there is a possibility to adjust the impact and tensile properties of the blend by selecting a PBA-cs-PMMA with a proper core/shell ratio. Hence, a modified PC material with balanced mechanical properties may be prepared.

Effect of the core-shell latex polymer content on the compatibility, morphology and mechanical properties of PC/PBA-cs-PMMA blends

The toughening effect of the content of a core-shell poly(butyl acrylate)/poly(methyl methacrylate) latex polymer (PBA-cs-PMMA) on the mechanical properties, morphology and compatibility of its blends with polycarbonate(PC), i.e., PC/PBA-cs-PMMa, was studied. The mechanical properties of the blends are strongly affected by varying the content of PBA-cs-PMMA in the blend. When the PBA-cs-PMMA content is only 5 wt.-%, the impact strength of PC/PBA-cs-PMMA is almost 19 times as high as that of pure PC, indicating that PBA-cs-PMMA is a very good impact modifier for PC. With increasing interphacial layer thickness and decreasing interphacial tension, the interphacial activity becomes more and more effective and, at the same time, miscibility increases too.

Preliminary investigations on polymerization catalysts composed of lanthanocene and methylaluminoxane

The polymerization of butadiene(Bd), isoprene(Ip) and styrene(St) has been examined using the six catalyst systems composed of lanthanocene, (C5H9Cp)(2)NdCl(I), (C5H9Cp)(2)SmCl(II), (MeCp)(2)SmOAr'(III), (Ind)(2)NdCl(IV), Me2Si(Ind)(2)NdCl(V) and (Flu)(2)NdCl(VI), and methylaluminoxane(MAO) respectively. All of them can be used to form the polyisoprene with molecular weights of 1 to 10 thousand and cis-1,4-unit contents of 41 to 47%. (I), (II) and (III) of them can be also used to form the polybutadiene with molecular weights of 10 to 20 thousand and cis-1,4-unit contents of 62 to 78%. In addition, the catalysts from (II) to (V) are still active for St polymerization and (II) of them gives a syndio -rich random polystyrene. It is noteworthy that (II) and (III) are active for homopolymerization of Bd, Ip and St in the same polymerization condition.

Studies on the elimination of NO over the La-Ba-Cu mixed oxide catalysts with perovskite structure

The mixed oxides, including YBa2Cu3O7, LaBa2Cu3O7, LaBaCu2O5, La2BaCu3O7, La4BaCu5O12 with perovskite structure, were prepared. The catalysts were characterized by means of chemical analysis, XRD, TPD and TPR method. It was found that they were the active catalysts for the NO decomposition and NO reduction by CO. The existance of Cu3+ is an important factor to give the catalysts a high activity for the NO reduction by CO.

Polymerization of ethylene by zirconocene-B(C6F5)(3) catalysts with aluminum compounds

Ethylene polymerization by zirconocene-B(C6F5)(3) catalysts with various aluminum compounds has been investigated. It is found that the catalytic activity depended on zirconocenes used, and especially on the type of aluminum compounds. For Et(H(4)Ind)(2)ZrCl2 (H(4)Ind : tetrahydroindenyl), the activity decreases in the following order: Me3Al > i-Bu3Al > Et3Al much greater than Et2AlCl. While for Cp2ZrCl2(Cp : cyclopentadienyl), it varies as follows: i-Bu3Al > Me3Al much greater than Et3Al. Furthermore, the activity is significantly affected by the addition mode of the catalytic components, which may imply that the formation of active centers is associated with an existing concentration of catalytic components. Results of thermal behavior of polyethylene (PE) studied by differential scanning calorimetry(DSC) show that crystallinity of the polymer prepared with Et3Al is higher than that with Me3Al or i-Bu3Al. It is also found that the number-average molecular weight ((M) over bar) of the polymers prepared with Me3Al or i-Bu3Al is much higher than that with Et3Al. H-1-NMR studies substantiate that i-Bu3Al is a more efficient alkylation agent of Cp2ZrCl2 in comparison with Me3Al. (C) 1997 John Wiley & Sons, Inc.

Studies of catalyzed reaction mechanism between co-polyether (THF/EO) and N-100 by NMR - Interaction and complex formation between reactants and catalysts

To elucidate the mechanism of the catalyzed reaction of co-polyether (EO/THF) with N-100, the interaction and complex formation between reactants and catalysts were investigated by means of NMR spectroscopy. It is shown that the resonance peak of isocyanate carbon splits into two parts when the solutions of N-100 and co-polyether were mixed. The disappearing of proton resonance peak of hydroxyl group in NMR spectra when dibutyltin dilaurate(DBTDL) were added to the copolyether(THF/EO) solution indicates the complex formation, This interaction appears to be a bonding of tin to the oxygen of hydroxyl and make the hydrogen of the hydroxyl group very mobile and active, then exchange with other protons, In the case of triphenyl bismuth(TPB), the high field shift and intensity enhancement of proton peak were observed, which suggest a nucleophilic attack of the bismuth to the hydroxyl hydrogen.

Study on the Adsorption and Activation of NO and CO over Mixed Oxide Catalysts Containing Cu by Means of TPSR

Adsorption and activation of small molecules NO, CO and CO+ NO on LaSrCuO4, La2CuO4 and La1.7Th0.3CuO4 which are typical samples in the sence of nonstoichiometric oxygen(lambda) anrong the series of La2-x(SrTh)(x)CuO4 +/-lambda mixed oxide catalysts were studied by means of MS- TPD (TPSR ), XRD, chemical analysis and so on. It was shown that the adsorption amount of NO can be correlated with the content of oxygen vacancy while the types and strength of adsorption of NO could be related to the oxidation state of the metallic ion. It was also found that CO molecule was first converted into CO32- and then desorbed in the form of CO2 at high temperature during the adsorption and desorption of CO on the mixed oxide with oxygen vacancy. The fact that the profiles of TPD(TPSR) of NO in co-adsorption of NO+CO and in single NO adsorption are similar shows that the adsorption of NO molecule not only has some priority to that of CO but also is stronger than that of CO. It seems that the adsorption of NO plays a dominate role in the activation and decomposition of NO.

An effective etching technique for polycarbonate/core-shell poly(butyl acrylate) poly(methyl methacrylate) blend

Two etching techniques are used to reveal the morphology of PC/PBA-cs-PMMA blend. One is based on acetic acid (CH3COOH) solutions, whereas the other uses CCl4/ C2H5OH (3/1 v/v). The latter approach shows to be more appropriate and successful for revealing the morphology of PC/PBA-cs-PMMA blend.