Doubly fed wind turbine performance in variable grid conditions

Wind turbines based on doubly fed induction generators (DFIG) become the most popular solution in high power wind generation industry. While this topology provides great performance with the reduced power rating of power converter, it has more complicated structure in comparison with full-rated topologies, and therefore leads to complexity of control algorithms and electromechanical processes in the system. The purpose of presented study is to present a proper vector control scheme for the DFIG and overall control for the WT to investigate its behavior at different wind speeds and in different grid voltage conditions: voltage sags, magnitude and frequency variations. The key principles of variable-speed wind turbine were implemented in simulation model and demonstrated during the study. Then, based on developed control scheme and mathematical model, the set of simulation is made to analyze reactive power capabilities of the DFIG wind turbine. Further, the rating of rotor-side converter is modified to not only generate active rated active power, but also to fulfill Grid Codes. Results of modelling and analyzing of the DFIG WT behavior under different speeds and different voltage conditions are presented in the work.

Effects of Fin Parameters on Gas-Side Heat Transfer Performance of H-Type Finned Tube Bundle in a Waste Heat Recovery Boiler

Alfa Laval Aalborg Oy designs and manufactures waste heat recovery systems utilizing extended surfaces. The waste heat recovery boiler considered in this thesis is a water-tube boiler where exhaust gas is used as the convective heat transfer medium and water or steam flowing inside the tubes is subject to cross-flow. This thesis aims to contribute to the design of waste heat recovery boiler unit by developing a numerical model of the H-type finned tube bundle currently used by Alfa Laval Aalborg Oy to evaluate the gas-side heat transfer performance. The main objective is to identify weaknesses and potential areas of development in the current H-type finned tube design. In addition, numerical simulations for a total of 15 cases with varying geometric parameters are conducted to investigate the heat transfer and pressure drop performance dependent on H-type fin geometry. The investigated geometric parameters include fin width and height, fin spacing, and fin thickness. Comparison between single and double tube type configuration is also conducted. Based on the simulation results, the local heat transfer and flow behaviour of the H-type finned tube is presented including boundary layer development between the fins, the formation of recirculation zone behind the tubes, and the local variations of flow velocity and temperature within the tube bundle and on the fin surface. Moreover, an evaluation of the effects of various fin parameters on heat transfer and pressure drop performance of H-type finned tube bundle has been provided. It was concluded that from the studied parameters fin spacing and fin width had the most significant effect on tube bundle performance and the effect of fin thickness was the least important. Furthermore, the results suggested that the heat transfer performance would increase due to enhanced turbulence if the current double tube configuration is replaced with single tube configuration, but further investigation and experimental measurements are required in order to validate the results.

Evaluation of noni (Morinda citrifolia) volatile profile by dynamic headspace and gas chromatography-mass spectrometry

Noni is a fruit that has interested the scientific community due to its medicinal and functional activities. Different products that contain noni are already in the market, but their consumption could be impaired by their distinctive unpleasant aroma and flavor. The aim of this work was to evaluate the noni pulp volatile profile by dynamic headspace and gas chromatography-mass spectrometry. Thirty seven volatile compounds were detected, mainly alcohols (63.3%), esters (26.9%), cetones (7.4%), and acids (1.2%).

(E)-2-Nonenal determination in brazilian beers using headspace solid-phase microextraction and gas chromatographic coupled mass spectrometry (HS-SPME-GC-MS)

(E)-2-nonenal is considered an important off-flavor of beer, related to the flavor of beer staling. In this study, a new method for determination of (E)-2-nonenal in beer using headspace solid-phase microextraction and gas chromatographic coupled mass spectrometry (HS-SPME-GC-MS) was developed and applied in Brazilian beer samples. The extractions were carried out in CAR-PDMS (carboxen-polydimethylsiloxane) fiber and the best results were found with 15 minutes of equilibrium and 90 minutes of extraction at 50 °C. The method was linear in the range from 0.02 to 4.0 μg.L-1 with correlation coefficient of 0.9994. The limits of detection and quantification were 0.01 and 0.02 μg.L-1, respectively. 96.5% of recovery and 4% precision (RSD) were obtained in the fortification of beer samples with 2.0 μg.L-1 of (E)-2-nonenal. The developed method proved to be simple, efficient and highly sensitive to the determination of this analyte being easily applied in the quality control of the brewery. (E)-2-nonenal was found in all beer samples analyzed with levels between 0.17 and 0.42 μg.L-1.

Dynamics of gas levels inside packages containing minimally processed Pera orange

The purpose of this study was to evaluate the changes in concentrations of O2 and CO2 inside packages of minimally processed Pera orange. Previously selected oranges that were washed, sanitized, and chilled were peeled using hydrothermal treatment (immersion of fruits in water at 50 °C for 8 minutes). The peeled oranges were then packed in five different plastic packages under passive and active modified atmosphere (5% O2 + 10% CO2 + 85% N2). The fruits were stored at 6 °C and 12 °C. The package headspace gas composition was evaluated for twelve days at 6 °C and nine days at 12 °C. The polypropylene film (32 µm) promoted modified atmosphere similar to that initially injected (5% O2 + 10% CO2 + 85% N2) at 6 °C and 12 °C. With regard to the atmosphere modification system, the injection of a gas mixture anticipated achieving an equilibrium atmosphere inside the packages at 12 °C. At 6 °C, the gas composition inside the packages was kept close to that of the injection, but the equilibrium was not verified.

Characterization and classification of pequi trees (Caryocar brasiliense Camb.) based on the profile of volatile constituents using headspace solid-phase microextraction - gas chromatography - mass spectrometry and multivariate analysis

In order to determine the variability of pequi tree (Caryocar brasiliense Camb.) populations, volatile compounds from fruits of eighteen trees representing five populations were extracted by headspace solid-phase microextraction and analyzed by gas chromatography-mass spectrometry. Seventy-seven compounds were identified, including esters, hydrocarbons, terpenoids, ketones, lactones, and alcohols. Several compounds had not been previously reported in the pequi fruit. The amount of total volatile compounds and the individual compound contents varied between plants. The volatile profile enabled the differentiation of all of the eighteen plants, indicating that there is a characteristic profile in terms of their origin. The use of Principal Component Analysis and Cluster Analysis enabled the establishment of markers (dendrolasin, ethyl octanoate, ethyl 2-octenoate and β-cis-ocimene) that discriminated among the pequi trees. According to the Cluster Analysis, the plants were classified into three main clusters, and four other plants showed a tendency to isolation. The results from multivariate analysis did not always group plants from the same population together, indicating that there is greater variability within the populations than between pequi tree populations.

Carponate precipitation with carbon dioxide gas

The aim of this thesis research work focused on the carbonate precipitation of magnesium using magnesium hydroxide Mg(OH)2 and carbon dioxide (CO2) gas at ambient temperature and pressure. The rate of dissolution of Mg(OH)2 and precipitation kinetics were investigated under different operating conditions. The conductivity and pH of the solution were inline monitored by a Consort meter and the solid samples gotten from the precipitation reaction were analysed by a laser diffraction analyzer Malvern Mastersizer to obtain particle size distributions (PSD) of crystal samples. Also the Mg2+ concentration profiles were determined from the liquid phase of the precipitate by ion chromatography (IC) analysis. Crystal morphology of the obtained precipitates were also investigated and discussed in this work. For the carbonation reaction of magnesium hydroxide in the present work, it was found that magnesium carbonate trihydrate (nesquehonite) was the main product and its formation occurred at a pH of around 7-8. The stirrer speed has a significant effect on the dissolution rate of Mg(OH)2. The highest obtained Mg2+ concentration level was 0.424 mol L-l for the 470 rpm and 0.387 mol L-1 for the 560 rpm which corresponded to the processing time of 45 mins and 40 mins respectively. The particle size distribution shows that the average particle size keeps increasing during the reaction as the CO2 is been fed to the system. The carbonation process is kinetically favored and simple as nesquehonite formation occurs in a very short time. It is a thermodynamically and chemically stable solid product, which allows for a long-term storage of CO2. Since the carbonation reaction is a complex system which includes dissolution of magnesium hydroxide particles, absorption of CO2, chemical reaction and crystallization, the dissolution of magnesium hydroxide was studied in hydrochloric acid (HCl) solvent with and without nitrogen (N2) inert gas. It was found on the dissolution part that the impeller speed had effect on the dissolution rate. The higher the impeller speed the higher the pH of the solution, although for the highest speed of 650rpm it was not the case. Therefore, it was concluded that the optimum speed of the stirrer was 560rpm. The influence of inert gas N2 on the dissolution rate of Mg(OH)2 particles could be seen based on measured pH, electric conductivity and Mg2+ concentration curves.

New aspects in limestone dissolution for wet flue gas desulfurization

Fortsättningsvis tillgodoses största delen av världens energibehov genom förbränning av fossila bränslen, dessutom forsätter världens totala energibehov att öka. Eftersom förbränning av fossila bränslen som t.ex. olja och kol orsakar utsläpp av svaveldioxid som är skadligt för både människa och natur, finns det fortfarande ett akut behov av forskning och utveckling av metoder för svavelrening. De vanligaste teknikerna för svavelrening är våt- och semitorrskrubbning, där svaveldioxiden absorberas av en skrubbervätska. Det är allmänt känt att våtskrubbning är en av de effektivaste teknikerna för svavelrening både ekonomiskt och tekniskt sett samt den mest använda. Våtskrubbningsprocessen har dock flera nackdelar, som dess höga vatten- och energiförbrukning. I större kraftverk går ca 1-3% av dess eleffekt åt till rökgasreningsprocessen, vilket kraftigt motiverar utveckling av nya reningsprocesser samt effektivering av existerande reningsanläggningar. Skrubbervätskan som till huvudsak består av vatten innehåller vanligtvis även kalcium vars syfte är att binda svavlet. Kalciumet kan tillsättas i flera former varav bränd kalk och kalksten är de vanligaste formerna. Kalksten används ofta i svavelreningsprocessen p.g.a. dess låga pris och för att den ger upphov till den användbara biprodukten gips. Kalkstenens upplösningshastighet är en de av faktorer som kraftigast påverkar reningsprocessen. En detaljerad experimentell karakterisering och analys av kalkstenspartiklar i fast form och i vätskeform har utförts i detta arbete. En experimentell metod för att studera kalkstenens upplösningshastighet vid låg till obegränsad massöverföring har även utvecklats i detta arbete. Metoden möjliggör identifieringen av systemoberoende kinetiska parametrar, vilka kan användas för att undersöka reningsprocesser samt för att planera nya reningsanläggningar. Kinetiska modeller utvecklades genom att använda kalkstenpartiklars specifika yta, som mättes genom kväveadsorption. Efter att de kinetiska parametrarna bestämts experimentellt utvecklades en skrubbermodell för att optimera en i driftvarande skrubber. Genom att kombinera experimentellt bestämda modeller med matematisk optimering erhölls en djupare insikt i hur olika råmaterial påverkar processen och hur driftparameterar bör justeras för att minska elförbrukningen.

Co-creating Value For Smart Phone Operating Systems Via Virtual Discussion Forums

In the traditional way, value is created by manufacturer or producer of a product without engaging the customers. So, traditionally value creation is a monopoly in the part of a manufacturer. After gathering all the raw materials the manufacturers are inserting value to a product. And the inserted value is recognized in the time of consuming the product. In the modern time though there is traditional way of value creation but with the increase of more educated, smart, and technically sound customers the idea of value creation has changed. Now, customers are also contributing in value creation as value co-creator even before the product is consumed. This scenario has been encountered in the thesis with the main purpose of how value is cocreated in smart phone operating systems. The purpose is further divided into the following supobjectives: o What is value co-creation in smart phone operating systems? o Who participates in value co-creation in smart phone operating systems? o What are the procedures that are involved in value co-creation in smart phone operating systems? The research was conducted as a qualitative desk study by observing two of the leading smart phone operating system providers. Data has been collected from the official discussion forum of both the operating system providers. Other general concepts relating to the purpose of the study has been encountered through literature review. The research findings reveal that customers and companies both together co-create value of anticipated level when they communicate and interact with each other. However, most of the time customer to customer interactions, dialogues and discussions that come out in the core conversation help the value co-creation. The value co-creation framework sets up the customer at the main focus of value creation theory. By nullifying the inherited notion that companies only create value within its boundary and provide it to their customers in exchange of currencies. Rationally, it has been commenced that the firms are merely compromising value propositions to its customers. But the value has been co-created in a point where offerings are combined and interacted with customers’ capabilities, knowledge, resources and perceptions. This new perspective has radically altered the prospect of firms towards its customers. Typically customers are now taking part in value cocreation as a crucial member.

The relationship between b2b branding and industrial buying in the digital era: evidence from Finnish gas industry

The aim of this study is to understand the importance of b2b brands in different phases of the industrial buying process in the digital era. The research problem is approached by examining a b2b supplier brand in the context of gas supplier selection. The data was collected by interviewing individuals from ten different companies. The findings contribute to previous theory by showing that as industrial buying behaviour is eventually individual behaviour, brands can influence decision making. The relevance of a brand depends on individual’s personality and preferences. Digital media cannot be ignored in managing brand image as buyers are present in the online environment. The results reveal that traditional personal selling is, nevertheless, in a key role in brand image building and is a source of added value. The salesperson influences buyers’ perceived associations of a brand and gives the brand a face.

Kaukolämpöliiketoiminnan kehittäminen Mäntsälän Sähkö osakeyhtiössä

Tämän diplomityön tarkoitus oli selvittää Mäntsälän Sähkö Oy:n kaukolämpöliiketoiminnan nykytila ja kehityskohteet. Tutkimuskysymykset olivat: 1) Millaisilla toimenpiteillä varmistetaan kaukolämpöliiketoiminnan kannattavuus tulevaisuudessa? ja 2) Millaisia mahdollisuuksia älykäs kaukolämpö tuo kaukolämpöliiketoiminnalle? Tutkimus suoritettiin perehtymällä aiheen kirjallisuuteen ja uutisiin. Takaisinmaksuajan menetelmällä arvioitiin maakaasun korvaamisen kannattavuutta. Työn tuloksena voitiin todeta, että kaukolämmön hinnoittelua kannattaa kehittää kustannusvastaavampaan suuntaan. Nykyinen kaukolämmön energiankulutukseen painottuva hinnoittelu ei sovi uusille rakennuksille, jotka kuluttavat vähän energiaa. Yleistyvät hybridilämmitysjärjestelmät on otettava huomioon hinnoittelussa. Kaukolämmön kausihinnoittelu toisi etuja asiakkaalle, kaukolämpöyhtiölle sekä ympäristölle. Kaukolämmön kulutuksen tuntimittaus mahdollistaisi siirtymisen kaukolämpötehoon perustuvaan hinnoitteluun. Kaukolämmön hinta on ollut Mäntsälän Sähkö Oy:llä suhteellisen korkea. Korkea hinta johtuu enimmäkseen maakaasulla tuotetun kaukolämmön korkeista tuotantokustannuksista. Kaukolämmön tuotantoa voidaan kehittää kannattavammaksi, vaikka lämmöntalteenottolaitoksen oletettu lämmöntuotanto kattaa Mäntsälän lämmöntarpeesta noin puolet ja vähentää tuotantokustannuksia. Nykyisten maakaasukattiloiden käyttäminen pelletin pölypolttoon olisi teknisten muutoksien avulla mahdollista. Pölypolton kannattavuus riippuu erityisesti puupelletin ja maakaasun hintaerosta. Älykäs kaukolämpöjärjestelmä voisi automaattisesti tasoittaa kaukolämmön kysyntää yhdessä lämpövaraston kanssa. Tällöin huippulämpölaitosten käyttö vähentyisi ja lämmöntuotannon kustannukset pienentyisivät. Älykäs kaukolämpöjärjestelmä ja kaukolämpötehon tuntimittaus mahdollistaisivat myös kaksisuuntaisen kaukolämpökaupan.

Screening of power to gas projects

The purpose of this thesis was the screening of power to gas projects worldwide and reviewing the technologies used and applications for the end products. This study focuses solely on technical solutions and feasibility, economical profitability is excluded. With power grids having larger penetrations of intermittent sources such as solar and wind power, the demand and production cannot be balanced in conventional methods. Technologies for storing electric power in times of surplus production are needed, and the concept called power to gas is a solution for this problem. A total of 57 projects mostly located in Europe were reviewed by going through publications, presentations and project web pages. Hydrogen is the more popular end product over methane. Power to gas is a viable concept when power production from intermittent sources needs to be smoothed and time shifted, when carbon free fuels are produced for vehicles and when chemical industry needs carbon neutral raw materials.