Hacia una taxonomía constructiva de las tapias de tierra y fábricas encofradas históricas = Towards a constructive taxonomy of the historical rammed-earth and formwork masonry

El objetivo fundamental de la investigación es el estudio de los fundamentos constructivos de las fábricas históricas de tapia de tierra y mampostería encofrada de las fortificaciones bajomedievales. Ante las incertidumbres detectadas en la datación de estas estructuras y frente al excesivo número de excepciones que quedan fuera de las clasificaciones tradicionalmente empleadas para estudiar este tipo de técnicas, el artículo desarrolla una propuesta de tipología o taxonomía constructiva basada en un sistema abierto. Este sistema nace del análisis de un número significativo de fábricas y atiende a diversos parámetros de control para la completa caracterización de cada fábrica: material, grado de compactación, función constructiva, encofrado, acabado superficial, combinación de materiales y situación, profundidad, formación y sección de los agujales. Cada fábrica se clasifica mediante una etiqueta alfanumérica. El sistema permite establecer tipos constructivos con los que se genera una clasificación cronotipológica constructiva. ABSTRACT The principal aim of the research is the study of the constructive reasons of the historical masonries built with rammed earth and formwork masonry, belonging to late medieval fortifications. Uncertainties have been warned about dating the historical masonries and there are excessive exceptions that do not fall in the rankings traditionally employed to study these techniques. Due to these reasons, the article develops a proposal of constructive typology or taxonomy based in an open system that comes from the analysis of a representative number of masonries and that attends to several control parameters tor the complete characterization of each masonry: material, compaction degree, constructive function, formwork, rendering, combination of materials and, last, the situation, deepness, formation and section of the putlogholes. Each masonry is classified through an alphanumeric label. The system allows establishing several constructive types which it is possible to do a cronotypological and constructive classification.

Dissolved CO2 and Alkane Gas in Clay Formations

Characterization of dissolved CO2 and alkane gas in clayrocks may help assessing the confinement properties of geological barriers considered as potential host rocks for a deep geological disposal as well as for caprocks of gas storages. A monitoring of alkanes with CO2, combined with carbon isotopes was performed on core samples coming from Underground Research Laboratories (Bure, Mont Terri, Tournemire) and the Schlattingen borehole in France and Switzerland. Composition of hydrocarbon gas and delta C-13 of methane strongly suggest a dominant thermogenic origin of methane which is mixed with a bacterial origin for the Toarcian shales, Pliensbachien and Callovian-Oxfordian clayrocks. Results also evidence the contrasted behavior of CO2, which is controlled by chemical equilibrium between pore water and carbonate mineralogy, compared to the alkanes which are present in the porosity as a stock of dissolved gases which can be depleted during degassing experiments. (C) 2015 The Authors. Published by Elsevier B.V.

(Table S1) Boron isotope and trace element data and reconstructed carbonate system parameters, ODP Holes 122-761B and 154-926A

The middle Miocene Climatic Optimum (17-15 Ma; MCO) is a period of global warmth and relatively high CO2 and is thought to be associated with a significant retreat of the Antarctic Ice Sheet (AIS). We present here a new planktic foraminiferal d11B record from 16.6 to 11.8 Ma from two deep ocean sites currently in equilibrium with the atmosphere with respect to CO2. These new data demonstrate that the evolution of global climate during the middle Miocene (as reflected by changes in the cyrosphere) was well correlated to variations in the concentration of atmospheric CO2. What is more, within our sampling resolution (~1 sample per 300 kyr) there is no evidence of hysteresis in the response of ice volume to CO2 forcing during the middle Miocene, contrary to what is understood about the Antarctic Ice Sheet from ice sheet modelling studies. In agreement with previous data, we show that absolute levels of CO2 during the MCO were relatively modest (350-400 ppm) and levels either side of the MCO are similar or lower than the pre-industrial (200-260 ppm). These new data imply the presence of either a very dynamic AIS at relatively low CO2 during the middle Miocene or the advance and retreat of significant northern hemisphere ice. Recent drilling on the Antarctic margin and shore based studies indicate significant retreat and advance beyond the modern limits of the AIS did occur during the middle Miocene, but the complete loss of the AIS was unlikely. Consequently, it seems that ice volume and climate variations during the middle Miocene probably involved a more dynamic AIS than the modern but also some component of land-based ice in the northern hemisphere.

Sm-Nd isotope and Mn/Ca ratios for cleaned Neogloboquadrina pachyderma from ODP Hole 105-647A (Table 1)

The neodymium (Nd) isotope composition of ancient seawater is a potentially useful tracer of changes in continental inputs and ocean circulation on timescales of a few ka. Here we present the first Nd isotope record for seawater using sedimentary foraminifera cleaned using standard oxidative-reductive techniques. The data, along with Mn/Ca ratios, suggest that cleaned foraminifera provide a reliable record of Nd in seawater and hold out the prospect of using Nd in foraminifera to examine changes in seawater that accompany glacial-interglacial climatic cycles. The principal potential problem to be overcome with the use of forams as records of trace elements in ancient seawater is their diagenetic Fe-Mn coatings. These contain large amounts of Nd and other trace elements but can be cleaned off using highly reducing reagents. Mn(Ca ratios for the majority of the cleaned sedimentary foraminifera analysed here lie within the range (10-100 µmol/mol) that has yielded success in studies of transition elements in forams. Mass-balance modelling suggests that for residual Mn/Ca ratios <100 µmol/mol, Nd added to the foram in the coating will never shift the measured Nd isotope composition significantly away from the seawater value acquired by the foram test in the water column. Additionally, Nd concentrations measured in cleaned sedimentary foraminifera are comparable with those for a modern sample that has never encountered diagenetic fluids. Finally, core-top planktonic foraminifera for two sites have Nd isotope compositions that are identical to local surface seawater. The data we present here for Labrador Sea forams over the past 2.5 m.y. are interpreted in terms of changes in the seawater isotopic composition. The data show a pronounced shift from epsilon-Nd values of ~-12 to ~-19 in the period 2.5-1.5 Ma. This change is interpreted to result from the initiation of Northern Hemisphere glaciation and the increased derivation of Labrador Sea Nd via ice-rafting from Archaean terranes in central Canada. In combination with stable isotope and foraminiferal relative species abundance data, the new Nd data are consistent with the surface hydrography of the Labrador Sea being dominated by a fluctuating balance between cold, polar waters containing unradiogenic Nd and warm, subtropical waters containing more radiogenic Nd. The major change in Labrador Sea Nd that is observed in the past 2.5 Ma can, on its own, account for the change in the Nd isotope composition of North Atlantic Deep Water over the same time period.

Strontium and boron geochemistry of ODP sites at Hydrate Ridge, eastern Pacific Ocean

ODP Leg 204, which drilled at Hydrate Ridge, provides unique insights into the fluid regime of an accretionary complex and delineates specific sub-seafloor pathways for fluid transport. Compaction and dewatering due to smectite-illite transition increase with distance from the toe of the accretionary prism and bring up fluids from deep within the accretionary complex to sampled depths (<= 600 mbsf). These fluids have a distinctly non-radiogenic strontium isotope signature indicating reaction with the oceanic basement. Boron isotopes are also consistent with a deep fluid source that has been modified by desorption of heavy boron as clay minerals change from smectite to illite. One of three major horizons serves as conduit for the transport of mainly fluid. Our results enable us to evaluate fluid migration pathways that play important roles on massive gas hydrate accumulations and seepage of methane-rich fluids on southern Hydrate Ridge.

Lithium isotopic composition of pore fluids and sediments in the Costa Rica subduction zone

Pore fluid and sediment Li concentrations and isotopic ratios provide important insights on the hydrology, sediment contribution to the arc volcanoes and fluid-sediment reactions at the dominantly non-accretionary Costa Rica subduction zone. Ocean Drilling Program Site 1039 in the trench axis provides a reference section of 400 m of the incoming sediments, and Site 1040, situated arcward from the trench, consists of a deformed sedimentary wedge and apron sediments, the décollement, and the partially dewatered underthrust sediment section. At the reference site, pore fluids show important isotopic variations (delta6Li=-21.7 to -37.8 per mil), reflecting the interplay of in situ alteration of volcanic material and ion exchange with clay minerals. In the basal section, a reversal of Li concentration and delta6Li toward seawater values is observed, providing supporting evidence for a lateral seawater flow system in the upper oceanic basement underlying this sediment section. At Site 1040, pore fluid of the lower deformed wedge sediments and within the décollement is enriched in Li and the isotopic compositions are relatively light, suggesting infiltration of a deep-seated fluid. The delta6Li value of -22 per mil of this Li-enriched fluid (261 µM), when compared with the delta6Li value of the subducted sediment section (-11 per mil), suggests that the deep source fluid originates from mineral fluid dehydration and transformation reactions at temperatures of 100 to 150°C, consistent with the temperature range of the up-dip seismogenic zone and of transformation of smectite to illite. The distribution of Li and its isotopes in the underthrust section are similar to those at the reference site, indicating near complete subduction of the incoming sediments and that early dewatering of the underthrust sediments occurs predominantly by lateral flow into the ocean. The hemipelagic clay-rich sediment section of the subducting plate carries most of the Li into this subduction zone, and the pelagic diatomaceous and nannofossil calcareous oozes contain little Li. The Li isotopes of both the clay-rich hemipelagic sediments and of the pelagic oozes are, however, similar, with delta6Li values of -9 to -12 per mil. The observations that (1) the delta6Li values of the underthrust sediments are distinctly lower than that of the mantle, and (2) the lavas of the Costa Rican volcanoes are enriched in Li and 7Li, provide an approximation of the contribution of the subducted sediments to the arc volcanoes. A first order mass balance calculation suggests that approximately half of the Li flux delivered by subducted sediments and altered oceanic crust into the Middle American Trench is recycled to the Costa Rican arc and at most a quarter of sedimentary Li is returned into the ocean through thrust faults, primarily the décollement thrust.

Rare earth and trace elements in igneous and metamorphic minerals of oceanic gabbros from the Mid-Atlantic Ridge

SIMS analyses have been carried out on clinopyroxenes, plagioclases and amphiboles of six gabbroic samples from Holes 921-924 of the Ocean Drilling Program Leg 153 sited in the MARK area of the Mid-Atlantic Ridge at the ridge-transform intersection, to investigate the rare earth, trace and volatile element distribution in the lower ocean crust during igneous crystallization and higher grade metamorphic conditions. The metagabbros underwent granulite to subgreenschist facies conditions through three main tectono-metamorphic phases: (1) ductile regime (750 < T < 1000 °C and P = 0.3 GPa); (2) transitional regime (600 < T < 700 °C and P = 0.2 GPa); (3) brittle regime (350 < T < 600 °C and P < 0.2 GPa). Igneous clinopyroxenes show Cl-chondrite normalized patterns depleted in LREE, and nearly flat for HREE. The rare earth and trace element distributions in igneous clinopyroxenes and plagioclases indicate that these minerals act as REE reservoirs, and comprise the main contribution to the overall rock content. The abundances in igneous minerals reflect the degree of fractionation of the parent liquids. In metamorphic clinopyroxenes recrystallized in anhydrous assemblages, the REE and trace elements patterns mimic those of the primary ones. Conversely, clinopyroxerie re-equilibrated in amphibolebearing assemblages shows a significant increase in REE, Ti, Zr, Y and V, a negative Eu anomaly, and slight decreases in Sr and Ba. An overall increase of REE and some trace elements is evident in hydrous assemblages, with preferential partitioning in the amphibole. It shows high Ti (18196-22844 ppm), LREE depleted patterns and LaN/SmN = 0.10-0.33, LaN/YbN = 0.10-0.30. Amphiboles from granoblastic assemblages show homogeneous patterns with no or a positive anomaly for TiN and negative anomalies for SrN and ZrN. Volatiles in amphibole are low, with Cl/F < 1; H2O% is significantly lower than the stoichiometric ratio (1.33-1.53%). The composition of the clinopyroxene and amphibole recrystallized in low-strain domains records evidence of incomplete re-equilibration, and element diffusion and partitioning is in part controlled by the textural site. The possible origins of the fluids involved in the metamorphic recrystallization are discussed: (1) remobilization from igneous amphibole; (2) exsolution from evolved melts; (3) introduction of seawater-derived fluids modified in rock-dominated systems; (4) injection of highly evolved hydrous melts during the metamorphic process.

Geochemistry and strontium isotopic composition of interstitial waters of marine carbonates

The concentrations and isotopic compositions of strontium in interstitial waters from several DSDP sites, where sediments consist chiefly of carbonate oozes and chalks, are used as indicators of carbonate diagenesis by reference to a recently-produced curve showing detailed variations in the 87Sr/86Sr ratio of seawater with time. Carbonate sediments of the Walvis Ridge show increases in interstitial Sr[2+] concentrations in the upper carbonate-ooze sections with the highest concentrations near the ooze-chalk boundary where maximum rates of carbonate recrystallization occur. Below this, in situ production of Sr[2+] diminishes and there is a diffusive flux of Sr to an underlying sink, presumably volcanogenic sediments or basalts, leading to Sr isotopic disequilibrium between carbonates and interstitial waters. In some other sites, however, there is no apparent Sr sink at depth and isotopic equilibrium is retained. Overall, diffusive smoothing of profiles exerts an important control on the 87Sr/86Sr ratios, although lower ratios than contemporaneous seawater values in the carbonate oozes often correlate with zones of Mg[2+] loss and reflect a combination of a flux of Sr[2+] from the zone of maximum recrystallization rates together with a contribution from the in situ alteration of volcanic matter.

Trace element abundance, and Sr and Nd isotope ratios of dust samples in the Pacific Ocean (Table 2)

Eolian dust preserved in deep-sea sediment cores provides a valuable indicator of past atmospheric circulation and continental paleoclimate. In order to identify the provenance of eolian dust, Nd and Sr isotopic compositions and Rb, Sr and rare earth element (REE) concentrations have been determined for the silicate fractions of deep-sea sediments from the north and central Pacific Ocean. Different regions of the Pacific Ocean are characterized by distinct air-borne inputs, producing a large range in epsolin-Nd (-10 to +1), 87Sr/86Sr (0.705-0.721), La/Yb (5-15), EuN/EuN* (0.6-1.0) and Sr/Nd (4-33). The average Nd isotopic composition of Pacific deep-sea sediments (epsilon-Nd = -6), is more radiogenic than the average from the Atlantic (epsilon-Nd = -8). In contrast, the average147Sm/144Nd ratio for Pacific sediments (0.114) is identical to that of Atlantic sediments and to that of global average riverine suspended material. The values of epsilon-Nd and147Sm/144Nd are positively correlated for the Pacific samples but negatively correlated for Atlantic samples, reflecting a fundamental difference between the dominant components in the end members with radiogenic Nd (island-arc components in the Pacific and LREE-enriched intraplate ocean island components in the Atlantic). Samples from the north central Pacific have distinctive unradiogenic epsilon-Nd values of -10, 87Sr/86Sr > 0.715, high La/Yb (> 12), and low EuN/EuN* (0.6) and Sr/Nd (3-6). These data are virtually identical to the values for loess from Asia and endorse the use of these sediments as indicators of Asian paleoclimate and paleowind directions. Island-arc contributions appear to dominate in the northwest Pacific, resulting in higher epsilon Nd (-1 to +1) and lower 87Sr/86Sr (~ 0.705) and La/Yb (~ 5). Sediments from the eastern Pacific tend to have intermediate Sr and Nd isotopic compositions but regionally variable Sr/Nd and REE patterns; they appear to be derived from the west margin of the North and South American continents, rather than from Asia. Our results confirm that dust provenance can be constrained by isotopic and geochemical analyses, which will facilitate reconstructions of past atmospheric circulation and continental paleoclimate.

Particel size distribution and microstructures of sediments from ODP Leg 205 sites (Table 1)

Ocean Drilling Program Legs 170 and 205 offshore Costa Rica provide structural observations which support a new model for the geometry and deformation response to the seismic cycle of the frontal sedimentary prism and decollement. The model is based on drillcore, thin section, and electron microscope observations. The decollement damage zone is a few tens of meters in width, it develops mainly within the frontal prism. A clear cm-thick fault core is observed 1.6 km from the trench. The lower boundary of the fault core is coincident with the lithological boundary between the frontal prism and the hemipelagic and pelagic sediment of the Cocos plate. Breccia clast distributions in the upper portion of the decollement damage zone were studied through fractal analysis. This analysis shows that the fractal dimension changes with brecciated fragment size, implying that deformation was not accommodated by self-similar fracturing. A higher fractal dimensionality correlates with smaller particle size, which indicates that different or additional grain-size reduction processes operated during shearing. The co-existence of two distinct fracturing processes is also confirmed by microscopic analysis in which extension fracturing in the upper part of the damage zone farthest from the fault core is frequent, while both extension and shear fracturing occur approaching the fault core. The coexistence of extensional and shear fracturing seems to be best explained by fluid pressure variations in response to variations of the compressional regime during the seismic cycle. During the co-seismic event, sub-horizontal compression and fluid pressure increase, triggering shear fracturing and fluid expulsion. Fractures migrate upward with fluids, contributing to the asymmetric shape of the decollement, while slip propagates. In the inter-seismic interval the frontal prismrelaxes and fluid pressure drops. The frontal prismgoes into diffuse extension during the intervalwhen plate convergence is accommodated by creep along the ductile fault core. The fault core is typically a barrier to deformation, which is explained by its weak, but impermeable, nature. The localized development of a damage zone beneath the fault core is characterized by shear fracturing that appears as the result of local strengthening of the detachment.