Production of hydrogen by ethanol steam reforming on Co/Al2O3 catalysts: Effect of addition of small quantities of noble metals

The catalytic performance of Co/Al2O3 catalysts promoted with small amounts noble metals (Pt, Pd, Ru, Ir) for steam reforming of ethanol (SRE) has been investigated. The catalysts were characterized by the energy dispersive X-ray, X-ray diffraction, BET surface area, X-ray absorption fine structure and temperature reduction programmed techniques. The results showed that the promoting effect of noble metals included a marked decrease of the reduction temperatures of both Co3O4 and cobalt surface species interacting with the support due to the hydrogen spillover effect, leading to a significant increase of the reducibilities of the promoted catalysts. The better catalytic performance for the ethanol steam reforming at 400 degrees C was obtained for the CoRu/Al2O3 catalyst, which presented an effluent gaseous mixture with the highest H, selectivity and the reasonable low CO formation. (C) 2007 Published by Elsevier B.V.

Evaluation of the light polymerization efficiency of copolymers used in dental formulations by differential scanning calorimetry

Different compositions of visible-light-curable triethylene glycol dimethacrylate/bisglycidyl methacrylate copolymers used in dental resin formulations were prepared through copolymerization photoinitiated by a camphorquinone/ethyl 4-dimethylaminobenzoate system irradiated with an Ultrablue IS light-emitting diode. The obtained copolymers were evaluated with differential scanning calorimetry. From the data for the heat of polymerization, before and after light exposure, obtained from exothermic differential scanning calorimetry curves, the light polymerization efficiency or degree of conversion of double bonds was calculated. The glass-transition temperature also was determined before and after photopolymerization. After the photopolymerization, the glass-transi-tion temperature was not well defined because of the breadth of the transition region associated with the properties of the photocured dimethacrylate. The glass-transition temperature after photopolymerization was determined experimentally and compared with the values determined with the Fox equation. In all mixtures, the experimental value was lower than the calculated value. Scanning electron microscopy was used to analyze the morphological differences in the prepared copolymer structures. (C) 2007 Wiley Periodicals, Inc.

An insight into the beginning stage of the aqueous ring opening metathesis polymerization of exo,exo-7-oxabicyclo[2.2.1]hept-5-ene-2,3-dicarboxylic acid with Ru(III) compounds: the consumption of Ru(III) species in the presence of carboxylic acids monitored by ESR spectroscopy

The presence of paramagnetic species in the aqueous ring opening metathesis polymerizations of the exo,exo-7-oxabicyclo[2.2.1]hept-5-ene-2,3-dicarboxylic acid monomer with RuCl(3) and K(2)[RuCl(5)H(2)O] compounds was studied using ESR techniques. It was observed that the intensities of the Ru(III) signals in the ESR spectra decrease on the time scale of the induction period so that the ROMP can take place. The intensity of the Ru(III) signal almost disappeared 50 min after reacting with K(2)[RuCl(5)H(2)O] and after 100 mm in the case of RuCl(3). Reactions of the cis-[Ru(NH(3))(4)(H(2)O)(2)](tfms)(3) and [Ru(NH(3))(5)H(2)O](tfms)(3) complexes with the monomer and different organic compounds representing the organic functions in the monomer (furan, norbornene, but-2-ene-1,4-diol and formic, acetic, oxalic and maleic acids) were also monitored by ESR and UV/vis spectra. It was deduced that the organic acids provide the disappearance of the Ru(III) signal. The proton NMR relaxation times of the residual water in D(2)O for reactions with oxalic acid suggested that the presence of paramagnetic ions in the solution decreases along with

To achieve safe and respectful maternity care in tertiary level hospitals in Nepal, relatives are a valued addition to the provision of maternity care

Introduction: The White Ribbon Alliance for safe motherhood believes respectful maternity care is the universal right of every childbearing woman. Methods: NHRC in 2012 approved an inquiry of respectful care at facility-based childbirth. Individual-, focus group interviews and content analysis was used for gathering and analysis of data. Findings: The participating women and the SBAs shared similar views, and this was that together the SBAs and relatives ensured the women remained within the comfort and safety zone when giving birth in a tertiary level maternity unit. Conclusion: The SBAs strategy of having relatives provides basic care alongside the provision of medical care by the SBAs is a strategy that Nepal could use to improve the quality of its maternity care without any additional costs. Clinical implication: Prenatal classes might contribute to preparing relatives. Further Research: Further research could evaluate such a strategy in order to determine its effectiveness in reduction of morbidity and mortality.

"Jag tänkte bara 15 + 7 – 6" : En empirisk studie om elevers tolkning av likhetstecknet och sambandet mellan addition och subtraktion

Syftet med denna studie är att undersöka elevers förståelse av likhetstecknet och sambandet mellan addition och subtraktion i årskurs 3 samt deras klasslärares uppfattning av den egna matematikundervisningen, som behandlar addition, subtraktion och likhetstecknet. Studiens syfte besvaras genom följande frågeställningar: Vad kan specifikt utformade matematikuppgifter ge för information om elevers förståelse av likhetstecknet och sambandet mellan addition och subtraktion i årskurs 3? samt Vad tänker en lärare om de resultat som framkommit av elevernas matematikuppgifter? Den empiriska undersökningen har genomförts med en kvantitativ metod, i form av en enkät där elever i årskurs 3 fått lösa speciellt utformade matematikuppgifter och en kvalitativ metod, i form av semi-strukturerad intervju med elevernas lärare. Det resultat som framkommit i undersökningen har analyserats med hjälp av en innehållsanalys. Resultatet visar att alla elever inte har kunskap om att likhetstecknet indikerar ekvivalens mellan höger sida och vänster sida om likhetstecknet, men en majoritet av eleverna har den förståelsen. Det var inte väntat från lärarens sida att fyra elever helt hade missförstått likhetstecknets betydelse. Läraren är medveten om att likhetstecknet kan vara svårt att förstå, men hade förväntat att alla elever skulle klara av att lösa minst matematikuppgifterna med de lägsta talen. Resultatet visar även att nio av sexton elever har förstått sambandet mellan addition och subtraktion. Läraren menar att det sambandet återkommer under hela lågstadiet och därför hade förväntat sig att fler elever sett sambandet. Men samtidigt anser läraren att det är positivt att lite mer än halva gruppen har förstått sambandet mellan addition och subtraktion. Slutligen visar resultatet av studien att missförståelse av likhetstecknet har inverkan på elevers resultat vid uppgifter med öppna utsagor, men inte vid uppgifter där talen på vänster sida om likhetstecknet är lika med ett tal på höger sida om likhetstecknet.

Australian sweet lupin flour addition reduces the glycaemic index of a white bread breakfast without affecting palatability in healthy human volunteers

The addition of some legume ingredients to bread has been associated with effects on glycaemic, insulinaemic and satiety responses that may be beneficial in controlling type 2 diabetes, cardiovascular disease and obesity. However, the effect of Australian sweet lupin (Lupinus angustifolius) flour (ASLF) is unknown. This investigation examined the effect of adding ASLF to standard white bread on post-meal glycaemic, insulinaemic and satiety responses and palatability in healthy subjects. Using a randomised, single-blind, cross-over design, 11 subjects consumed one breakfast of ASLF bread and two of standard white bread ≥ 7 days apart after fasting overnight. Each breakfast also included margarine, jam, and tea with milk and contained 50g available carbohydrate. On each test day, blood samples were taken after fasting, then several times over 2 hours post-prandially, and analysed for plasma glucose and serum insulin. Subjects rated breakfast palatability and perception of satiety, in the fasting state and over 3 hours post-prandially, after which food intake from an ad libitum buffet and for the rest of the day was recorded. Incremental areas under the curves for glucose, insulin and satiety, glycaemic index, insulinaemic index and satiety index were calculated. ASLF addition to the breakfast reduced its glycaemic index (mean ± SEM; ASLF bread breakfast = 74.0 ± 9.6. Standard white bread breakfast = 100, P=0.022), raised its insulinaemic index (ASLF bread breakfast = 127.7 ± 12.0. Standard white bread breakfast = 100, P=0.046), but did not affect palatability, satiety or food intake. ASLF addition resulted in a palatable breakfast; however, the potential benefits of the lowered glycaemic index may be eclipsed by the increased insulinaemic index.

Ecological attributes of strategic land acquisitions for addition to Victoria's public protected area estate : 2004-2005

The development of a comprehensive, adequate and representative reserve system is the key objective of the National Reserve System, and is supported by all Australian States and Territories. In Victoria, the purchase of private land for incorporation into the parks and reserves system assists in the protection of some of the State’s most endangered ecosystems. This article outlines the ecological attributes of private land purchased for addition to the Victorian public protected area system between 2004 and 2005.

Synthesis, polymerization and wool coating studies of 3-iso-butylpyrrole and 3-iso-pentylpyrrole

In a four-step method starting from pyrrole, the synthesis of 3-iso-butylpyrrole and 3-iso-pentylpyrrole, was achieved in 45 and 44% yields, respectively. Polymerization studies of these branched alkyl pyrroles are described and the results compared with those obtained for the unbranched structural isomers n-butyl and n-pentylpyrrole. A series of conductive textiles were produced by the chemical polymerization of the iso-alkylpyrroles using both solution and vapour polymerization techniques. Fabrics coated with poly-iso-alkylpyrrole formed using the solution polymerization method had a lower surface resistance than those formed using the vapour polymerization method. These conductivity results were in direct contrast to those previously obtained for 3-n-alkylpyrroles on fabrics. A remarkable crystal-like growth on the surface of the textile fabric was observed when solution polymerization of 3-iso-pentylpyrrole was employed—reinforcing the notion that subtle changes in monomer structure can drastically affect bulk polymer properties.

Conductive wool yarns by continuous vapour phase polymerization of pyrrole

Conducting polypyrrole (PPy) coated wool yarns were prepared by a continuous vapour polymerization technique, using a speed of 1 m/min with different iron(III) chloride (FeCl₃) as the oxidant at different concentrations. The resistivities, tensile properties, longitudinal and cross-sectional views of PPy-coated wool yarns were investigated. Optimum specific electrical resistances of 2.96 Ω g/cm² at 80 g/L FeCl₃ and 1.69 Ω g/cm² at 70 g/L FeCl₃ were obtained for 500 and 400 twist per meter (TPM) yarns, respectively. PPy-coated wool yarns exhibited higher elongation than uncoated yarns. Longitudinal and cross-sectional views of the yarns indicate that PPy coating penetrated deep into the yarn cross-section and a uniform coating was obtained on the surface of the yarn surface.

Synthesis and polymerization studies of 3-(+) and (-) -menthyl carboxylate pyrroles

The synthesis of 3-(−)- and 3-(+)-menthyl carboxylate pyrrole was achieved in four high yielding steps, including the triisopropylsilyl (TIPS) protection of the pyrrole nitrogen, bromination of the 3-position, lithium halogen exchange followed by reaction with menthyl chloroformate, and finally de-protection. Chemical polymerization of both the TIPS protected, and non-protected, menthyl carboxylate pyrroles was performed and the resulting polymers exhibited conductivity ranging from 0.6 to 2.3 S/cm. Polymerization of the 3-menthyl-N-TIPS pyrrole on the surface of wool was achieved by using solution and mist polymerization methods.

The influence of polymerization time and dopant concentration on the absorption of microwave radiation in conducting polypyrrole coated textiles

Temperature changes in conducting polypyrrole/para-toluene-2-sulphonic acid (PPy/pTSA) coated nylon textiles due to microwave absorption in the 8–9 GHz and 15–16 GHz frequency ranges were obtained by a thermography station during simultaneous irradiation of the samples. The temperature values are compared and related to the amounts of reflection, transmission and absorption obtained with a non-contact free space transmission technique, indicating a relationship between microwave absorption and temperature increase. Non-conductive samples showed no temperature increase upon irradiation irrespective of frequency range. The maximum temperature difference of around 4 °C in the conducting fabrics relative to ambient temperature was observed in samples having 48% absorption and 26.5 ± 4% reflection. Samples polymerized for 60 or 120 min with a dopant concentration of 0.018 mol/l or polymerized for 180 min with a dopant concentration of 0.009 mol/l yielded optimum absorption levels. As the surface resistivity decreased and the reflection levels increased, the temperature increase upon irradiation reduced.

Conducting nylon, cotton and wool yarns by continuous vapor polymerization of pyrrole

Conductive textile yarns were prepared by a continuous vapor polymerization method; the application of polypyrrole by the continuous vapor polymerization method used is designed for the easy adaptation into industrial procedures. The resultant conductive yarns were examined by longitudinal and cross-sectional views, clearly showing the varying levels of penetration of the polymer into the yarn structure. It was found that for wool the optimum specific resistance was achieved by using the 400 TPM yarn with a FeCl3 solution concentration of 80 g/L FeCl3 to produce 1.69 Ω g/cm2. For cotton yarn, the optimum specific resistance of 1.53 Ω g/cm2 was obtained with 80 g/L of a FeCl3 solution.

Fuzzy neural networks for control of dynamic systems

This thesis provides a unified and comprehensive treatment of the fuzzy neural networks as the intelligent controllers. This work has been motivated by a need to develop the solid control methodologies capable of coping with the complexity, the nonlinearity, the interactions, and the time variance of the processes under control. In addition, the dynamic behavior of such processes is strongly influenced by the disturbances and the noise, and such processes are characterized by a large degree of uncertainty. Therefore, it is important to integrate an intelligent component to increase the control system ability to extract the functional relationships from the process and to change such relationships to improve the control precision, that is, to display the learning and the reasoning abilities. The objective of this thesis was to develop a self-organizing learning controller for above processes by using a combination of the fuzzy logic and the neural networks. An on-line, direct fuzzy neural controller using the process input-output measurement data and the reference model with both structural and parameter tuning has been developed to fulfill the above objective. A number of practical issues were considered. This includes the dynamic construction of the controller in order to alleviate the bias/variance dilemma, the universal approximation property, and the requirements of the locality and the linearity in the parameters. Several important issues in the intelligent control were also considered such as the overall control scheme, the requirement of the persistency of excitation and the bounded learning rates of the controller for the overall closed loop stability. Other important issues considered in this thesis include the dependence of the generalization ability and the optimization methods on the data distribution, and the requirements for the on-line learning and the feedback structure of the controller. Fuzzy inference specific issues such as the influence of the choice of the defuzzification method, T-norm operator and the membership function on the overall performance of the controller were also discussed. In addition, the e-completeness requirement and the use of the fuzzy similarity measure were also investigated. Main emphasis of the thesis has been on the applications to the real-world problems such as the industrial process control. The applicability of the proposed method has been demonstrated through the empirical studies on several real-world control problems of industrial complexity. This includes the temperature and the number-average molecular weight control in the continuous stirred tank polymerization reactor, and the torsional vibration, the eccentricity, the hardness and the thickness control in the cold rolling mills. Compared to the traditional linear controllers and the dynamically constructed neural network, the proposed fuzzy neural controller shows the highest promise as an effective approach to such nonlinear multi-variable control problems with the strong influence of the disturbances and the noise on the dynamic process behavior. In addition, the applicability of the proposed method beyond the strictly control area has also been investigated, in particular to the data mining and the knowledge elicitation. When compared to the decision tree method and the pruned neural network method for the data mining, the proposed fuzzy neural network is able to achieve a comparable accuracy with a more compact set of rules. In addition, the performance of the proposed fuzzy neural network is much better for the classes with the low occurrences in the data set compared to the decision tree method. Thus, the proposed fuzzy neural network may be very useful in situations where the important information is contained in a small fraction of the available data.