Improving the stability of an oxime based electrochemical microsensor for organo-phosphate vapor detection

A micro gas sensor has been developed by our group for the detection of organo-phosphate vapors using an aqueous oxime solution. The analyte diffuses from the high flow rate gas stream through a porous membrane to the low flow rate aqueous phase. It reacts with the oxime PBO (1-Phenyl-1,2,3,-butanetrione 2-oxime) to produce cyanide ions, which are then detected electrochemically from the change in solution potential. Previous work on this oxime based electrochemistry indicated that the optimal buffer pH for the aqueous solution was approximately 10. A basic environment is needed for the oxime anion to form and the detection reaction to take place. At this specific pH, the potential response of the sensor to an analyte (such as acetic anhydride) is maximized. However, sensor response slowly decreases as the aqueous oxime solution ages, by as much as 80% in first 24 hours. The decrease in sensor response is due to cyanide which is produced during the oxime degradation process, as evidenced by the cyanide selective electrode. Solid phase micro-extraction carried out on the oxime solution found several other possible degradation products, including acetic acid, N-hydroxy benzamide, benzoic acid, benzoyl cyanide, 1-Phenyl 1,3-butadione, 2-isonitrosoacetophenone and an imine derived from the oxime. It was concluded that degradation occurred through nucleophilic attack by a hydroxide or oxime anion to produce cyanide, as well as a nitrogen atom rearrangement similar to Beckmann rearrangement. The stability of the oxime in organic solvents is most likely due to the lack of water, and specifically hydroxide ions. The reaction between oxime and organo-phosphate to produce cyanide ions requires hydroxide ions, and therefore pure organic solvents are not compatible with the current micro-sensor electrochemistry. By combining a concentrated organic oxime solution with the basic aqueous buffer just prior to being used in the detection process, oxime degradation can be avoided while preserving the original electrochemical detection scheme. Based on beaker cell experiments with selective cyanide sensitive electrodes, ethanol was chosen as the best organic solvent due to its stabilizing effect on the oxime, minimal interference with the aqueous electrochemistry, and compatibility with the current microsensor material (PMMA). Further studies showed that ethanol had a small effect on micro-sensor performance by reducing the rate of cyanide production and decreasing the overall response time. To avoid incomplete mixing of the aqueous and organic solutions, they were pre-mixed externally at a 10:1 ratio, respectively. To adapt the microsensor design to allow for mixing to take place within the device, a small serpentine channel component was fabricated with the same dimensions and material as the original sensor. This allowed for seamless integration of the microsensor with the serpentine mixing channel. Mixing in the serpentine microchannel takes place via diffusion. Both detector potential response and diffusional mixing improve with increased liquid residence time, and thus decreased liquid flowrate. Micromixer performance was studies at a 10:1 aqueous buffer to organic solution flow rate ratio, for a total rate of 5.5 μL/min. It was found that the sensor response utilizing the integrated micromixer was nearly identical to the response when the solutions were premixed and fed at the same rate.

Valorização de resíduos provenientes da atividade no setor avícola: aplicação do processo de compostagem

O setor avícola, como setor em constante crescimento está associado à produção de elevadas quantidades de resíduos sólidos orgânicos. A crescente taxa de produção de resíduos avícolas leva à necessidade de lhes dar um destino adequado podendo a valorização orgânica, nomeadamente a compostagem, ser uma opção. O presente estudo pretende dar um contributo para o projeto de uma unidade de compostagem numa empresa portuguesa do setor, com valorização dos resíduos produzidos pela mesma, avaliando o potencial de aplicação desta operação de tratamento de resíduos e a qualidade do produto final. Como primeiro passo foi realizada uma caracterização dos resíduos a utilizar de forma a perceber a sua possível influência no processo de degradação. Os ensaios de compostagem foram realizados à escala laboratorial, numa gama de temperatura de 50 a 55ᵒC, utilizando como substrato base uma mistura dos resíduos avícolas, de acordo com os seus quantitativos de produção. Vários potenciais agentes estruturantes foram também testados, como adição ao substrato. A monitorização do processo foi feita com base em análises das fases gasosa (gases de exaustão), sólida (substrato em decomposição) e líquida (lixiviado). A avaliação do processo foi ainda complementada com a caracterização dos produtos finais obtidos, os quais foram ainda sujeitos a testes de fitotoxicidade. Foram observados graus de conversão de matéria orgânica relativamente altos (40-50%), comprovando a aplicabilidade desta operação de tratamento de resíduos. Embora a diferença entre ensaios tenha sido pouco notória, a utilização de uma combinação de cama de aviário e mato destroçado e compostado aparenta ser ligeiramente mais eficiente, enquanto a utilização de casca de eucalipto produziu os piores resultados. Perdas de humidade e de azoto foram as duas situações mais críticas observadas para os vários ensaios, tendo influência tanto sobre o processo como sobre o produto final. Os compostos obtidos revelam baixa qualidade, exibindo valores elevados de pH e condutividade elétrica e elevadas concentrações de metais pesados, tais como cobre e zinco. Supõe-se que as características adversas verificadas estejam associadas à aplicação de quantidades demasiado elevadas de cinza nos substratos, levando à necessidade de redução deste material; estudos adicionais seriam necessários a fim de avaliar as possibilidades de ajuste das quantidades a utilizar, dos diferentes materiais, com o intuito de produzir um produto final com qualidade, respeitando os requisitos legais.

Laser ablation-based one-step generation and bio-functionalization of gold nanoparticles conjugated with aptamers

Background: Bio-conjugated nanoparticles are important analytical tools with emerging biological and medical applications. In this context, in situ conjugation of nanoparticles with biomolecules via laser ablation in an aqueous media is a highly promising one-step method for the production of functional nanoparticles resulting in highly efficient conjugation. Increased yields are required, particularly considering the conjugation of cost-intensive biomolecules like RNA aptamers. Results: Using a DNA aptamer directed against streptavidin, in situ conjugation results in nanoparticles with diameters of approximately 9 nm exhibiting a high aptamer surface density (98 aptamers per nanoparticle) and a maximal conjugation efficiency of 40.3%. We have demonstrated the functionality of the aptamer-conjugated nanoparticles using three independent analytical methods, including an agglomeration-based colorimetric assay, and solid-phase assays proving high aptamer activity. To demonstrate the general applicability of the in situ conjugation of gold nanoparticles with aptamers, we have transferred the method to an RNA aptamer directed against prostate-specific membrane antigen (PSMA). Successful detection of PSMA in human prostate cancer tissue was achieved utilizing tissue microarrays. Conclusions: In comparison to the conventional generation of bio-conjugated gold nanoparticles using chemical synthesis and subsequent bio-functionalization, the laser-ablation-based in situ conjugation is a rapid, one-step production method. Due to high conjugation efficiency and productivity, in situ conjugation can be easily used for high throughput generation of gold nanoparticles conjugated with valuable biomolecules like aptamers.

Otimização e validação de um método para o preparo de suspensões e determinação de fulereno n-C60 em matriz aquosa

Com o aumento da produção do fulereno C60 e sua aplicação comercial é previsível que este composto acabe sendo liberado no ambiente, tornando-se um contaminante. Em razão das suas características físico-químicas e sua capacidade de formar agregados (n-C60) quando em contato com a água, o C60 pode se tornar um carreador de outros contaminantes (como metais e compostos orgânicos), facilitando a sua entrada nos organismos. Neste sentido, a sua toxicidade (tanto de forma isolada como em associação com outros contaminantes) vem sendo avaliada. Sendo assim, a fim de viabilizar os estudos com C60, uma metodologia para preparo de suspensões aquosas foi validada, sendo quantificada por CLAE/UV-Vis. As suspensões foram preparadas sem a adição de solvente de duas formas distintas, com aquecimento (50ºC) e à temperatura ambiente (≈20 ºC), onde se mantiveram sob agitação constante e exposição à luz artificial por até 2 meses. A cada 15 dias a suspensão foi quantificada. Além disso, três métodos distintos de extração e pré-concentração (extração líquido-líquido (ELL), extração em fase sólida (EFS) e micro-extração dispersiva líquido-líquido (MEDLL)) foram validados e comparados quanto a sua eficiência. Coeficientes de correlação ≥ 0,99 foram obtidos para as curvas de calibração. Os LDM e LQM foram de 0,08 e 0,3 ng mL-1 para EFS e ELL, considerando o fator de concentração de 500 vezes, e de 0,8 e 3,0 ng mL-1 para a MEDLL, considerando o fator de concentração de 50 vezes, respectivamente. A precisão (intermediária e repetitividade) variou entre 0,46 e 4,03 (%RSDpi) e entre 0,69 e 3,59 (%RSDr), enquanto que a exatidão ficou entre 72,3 e 85,6% para ELL, 86,1 e 115,5% para a EFS e 87,9 e 111,4% para MEDLL. Com base nestes parâmetros relativos a análise de suspensões aquosas de C60, a EFS foi considerada o método mais eficiente. O aquecimento se mostrou relevante no tamanho dos agregados, que foram significativamente maiores na suspensão sem aquecimento, porém o tempo de preparo da suspensão não influenciou na concentração final da suspensão. Portanto, recomenda-se o preparo das suspensões aquosas de C60 sem aquecimento por um período de agitação de 30-45 dias.

Avaliação da técnica de dispersão da matriz em fase sólida assistida por vórtex para análise de fármacos em peixes

Os fármacos classificados como contaminantes orgânicos emergentes tornaramse tópico de discussão ambiental pois estes são capazes de atingir diferentes matrizes do meio ambiente, como água, solo e organismos aquáticos, e estudos demonstrando a toxicidade tem despertado o interesse científico. Neste estudo um método analítico foi otimizado e validado para determinação de quinze fármacos em amostras de peixes empregando preparo de amostras por dispersão da matriz em fase sólida (MSPD) assistida por vórtex e determinação por cromatografia líquida acoplada a espectrometria de massas sequencial (LC-MS/MS). O estudo ainda focou na aplicação de diferentes suportes sólidos na etapa de dispersão da MSPD, sendo que três (quitina, quitosana e concha de mexilhão dourado) foram utilizados pela primeira vez para esta finalidade, O método otimizado foi validado seguindo os parâmetros do INMETRO, ANVISA, SANCO e FDA. A curva analítica e linearidade foram avaliados através da calibração externa e superposição na matriz. Os compostos demonstraram linearidade dentro da faixa recomendada, com coeficiente de correlação maior do que 0,99. Os limites de detecção do método variaram de 1 a 100 ng g -1 , e os limites de quantificação a variaram de 5 a 1000 ng g -1 . Os valores de recuperação variaram de 68% a 108%, com RSD menores que 13% para todos os compostos. O efeito de matriz foi avaliado e quatro dos quinze compostos apresentaram efeito maior que ±20%. Na aplicabilidade o método demonstrou ser eficiente para extração de fármacos de diferentes espécies de peixe, apresentando exatidão e precisão adequados. Não foram encontrados resíduos de fármacos nas amostras analisadas.

Dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por cianobactéria integrado a biorrefinarias agroindustriais

O objetivo desta tese foi avaliar a dinâmica do fósforo em cultivo heterotrófico e produção de compostos celulares por Aphanothece microscopica Nägeli visando avaliar a perspectiva de implementação de uma biorrefinaria microalgal. Desta forma, foi avaliado o comportamento do micro-organismo em estudo no cultivo heterotrófico, utilizando como meio de cultivo o efluente de laticínios. O trabalho foi desenvolvido em 3 etapas. Em um primeiro momento foi avaliada a influência da temperatura (20 e 30°C) e os valores máximos e mínimos de nutrientes, em especial do fósforo dissolvido reativo (PDR), disponíveis no efluente de laticínio, na remoção de nutrientes. Os resultados demonstraram que a concentração inicial de fósforo dissolvido e a temperatura exerceram influência no crescimento celular e na eficiência de remoção de nutrientes. Em termos de otimização de processo os cultivos conduzidos a 20°C e maiores concentrações de PDR (5,5 mg.L-1 ) no efluente de laticínio, foram os mais eficientes na conversão de poluentes em biomassa e remoção de nutrientes. A segunda etapa foi desenvolvida com o objetivo de avaliar a dinâmica de distribuição de fósforo na fase líquida e sólida do reator heterotrófico, quando o efluente de laticínio foi tratado pela Aphanothece microscopica Nägeli, a 20°C e nas máximas concentrações de fósforo dissolvido encontradas no efluente. Foi demonstrado que as formas fosforadas na fase líquida do reator se caracterizam pela predominância da fração dissolvida em comparação à particulada e por apresentar como fração predominante a de fósforo orgânico. No que se refere à fase sólida, ficou demonstrado que a Aphanothece microscopica Nägeli, quando cultivada heterotroficamente apresenta 3,8 vezes mais fósforo que o requerido para o crescimento celular. Ficando demonstrado ainda que a remoção biológica de fósforo por Aphanothece microscopica Nägeli pode resultar em substanciais aportes financeiros para as estações de tratamento de efluentes. Uma terceira etapa foi desenvolvida, a qual teve como objetivo avaliar a estimativa de produção de compostos celulares por Aphanothece microscopica Nägeli, a partir do efluente de laticínio, bem como o efeito da redução de temperatura de cultivo no teor de lipídios , no momento em que é obtida a máxima concentração deste componente celular, nas condições otimizadas.Foi obtido na fase logarítmica de crescimento, concentrações de 41,8 % de proteinas, carboidratos 28,5 %, lipídios 10,4 % e minerais 10,8 %. O maior teor de lipídio registrado a 20°C correspondeu a biomassa analisada na fase logarítmica.Com a redução da temperatura para 5°C por um período de 30 h é possível obter concentrações de lipídios 2,4 vezes superior ao registrado na fase logarítmica a 20 °C. No entanto, não foram indicadas diferenças significativas (p≤0,05) em função da temperatura entre as concentrações de lipídios obtidas para a biomassa a 10°C em 40 h. O perfil de ácidos graxos da biomassa gerada a 20°C, apresentou como ácidos graxos majoritários, os ácidos graxos: palmítico, oléico, γ-linolênico, palmitoleico e esteárico, resultando um aumento na concentração de ácidos graxos saturados as espensa dos insaturados, quando a temperatura é reduzida. Em paralelo,um reator heterotrófico descontinuo foi definido, ficando demonstrado que a extrapolação da operação em batelada para contínua requer um biorreator heterotrófico com volume útil de trabalho de 240,51 m 3 , permitindo tratar 950 m3 diários de efluente, gerando 11,8 kg.d-1 de biomassa útil para produção de compostos celulares por Aphanothece microscopica Nägeli, visando à simultânea remoção de matéria orgânica, nitrogênio total e fósforo total, gerando insumos que podem suportar a implementação de uma biorrefinaria microalgal.

Validation d’un procédé automatisé d’extraction sur phase solide de glandes digestives de moules pour l’identification et la quantification des dinophysistoxines en LC/ESI/SM2 par piégeage d’ions quadripolaire

This report presents a new extraction method of the dinophysistoxins (DTXs), confirmed by quantification using high-performance liquid chromatography coupled to mass spectrometry with an ion trap and electro spray interface (HPLC/ESI/MS2). The method originality consists on the adaptation of DTXs basic extraction procedure (liquid/ liquid) to a solid phase extraction (SPE) via a robotic station: ASPEC XLi The parameters of the automatization procedure were optimized to obtain the best DTXs recovery rate. These improvements were loaded with digestive gland mussel homogenat realized on a silica cartridge SPE, activated in hexane/chloroform (50:50), washed with hexane/chloroform (50:50) and extracted by an elution gradient (chloroform methanol (65:35) and methanol (100%)). This method was validated according to two normative referentials (linearity, detection quantification limits and accuracy…) : - The Guide of the Pharmacy industry: Analytical Validation, report of the commission SFSTP 1992 (French Corporation of the Sciences and Technical Pharmaceutical), - - The Procedure of validation of an alternative method in compare to a reference method. (AFNOR, 1998. NF V 03-110). Comparison with the classical liquid/liquid extraction and the automated method present clear advantages. In an analytical method the extraction is generally considered to be the most labor-intensive and error-prone step. This new procedure allowed us to increase throughput, to improve the reproducibility and to reduce the error risks due to the individual manual treatments.

Determination of Signature Volatile Odor Chemicals Emanating from Novel Biological Specimens by Non-invasive Analytical Techniques for the Potential use in Forensic Identifications

Human scent, or the volatile organic compounds (VOCs) produced by an individual, has been recognized as a biometric measurement because of the distinct variations in both the presence and abundance of these VOCs between individuals. In forensic science, human scent has been used as a form of associative evidence by linking a suspect to a scene/object through the use of human scent discriminating canines. The scent most often collected and used with these specially trained canines is from the hands because a majority of the evidence collected is likely to have been handled by the suspect. However, the scents from other biological specimens, especially those that are likely to be present at scenes of violent crimes, have yet to be explored. Hair, fingernails and saliva are examples of these types of specimens. In this work, a headspace solid phase microextraction gas chromatography-mass spectrometry (HS-SPME-GC-MS) technique was used for the identification of VOCs from hand odor, hair, fingernails and saliva. Sixty individuals were sampled and the profiles of the extracted VOCs were evaluated to assess whether they could be used for distinguishing individuals. Preliminary analysis of the biological specimens collected from an individual (intra-subject) showed that, though these materials have some VOCs in common, their overall chemical profile is different for each specimen type. Pair-wise comparisons, using Spearman Rank correlations, were made between the chemical profiles obtained from each subject, per a specimen type. Greater than 98.8% of the collected samples were distinguished from the subjects for all of the specimen types, demonstrating that these specimens can be used for distinguishing individuals. Additionally, field trials were performed to determine the utility of these specimens as scent sources for human scent discriminating canines. Three trials were conducted to evaluate hair, fingernails and saliva in comparison to hand odor, which was considered the standard source of human odor. It was revealed that canines perform similarly to these alternative human scent sources as they do to hand odor implying that, though there are differences in the chemical profiles released by these specimens, they can still be used for the discrimination of individuals by trained canines.

Study of ammonia borane and its derivatives: Influence of nanoconfinements and pressures

Recently, ammonia borane has increasingly attracted researchers’ attention because of its merging applications, such as organic synthesis, boron nitride compounds synthesis, and hydrogen storage. This dissertation presents the results from several studies related to ammonia borane. ^ The pressure-induced tetragonal to orthorhombic phase transition in ammonia borane was studied in a diamond anvil cell using in situ Raman spectroscopy. We found a positive Clapeyron-slope for this phase transformation in the experiment, which implies that the phase transition from tetragonal to orthorhombic is exothermic. The result of this study indicates that the rehydrogenation of the high pressure orthorhombic phase is expected to be easier than that of the ambient pressure tetragonal phase due to its lower enthalpy. ^ The high pressure behavior of ammonia borane after thermal decomposition was studied by in situ Raman spectroscopy at high pressures up to 10 GPa. The sample of ammonia borane was first decomposed at ∼140 degree Celcius and ∼0.7 GPa and then compessed step wise in an isolated sample chamber of a diamond anvil cell for Raman spectroscopy measurement. We did not observe the characteristic shift of Raman mode under high pressure due to dihydrogen bonding, indicating that the dihydrogen bonding disappears in the decomposed ammonia borane. Although no chemical rehydrogenation was detected in this study, the decomposed ammonia borane could store extra hydrogen by physical absorption. ^ The effect of nanoconfinement on ammonia borane at high pressures and different temperatures was studied. Ammonia borane was mixed with a type of mesoporous silica, SBA-15, and restricted within a small space of nanometer scale. The nano-scale ammonia borane was decomposed at ∼125 degree Celcius in a diamond anvil cell and rehydrogenated after applying high pressures up to ∼13 GPa at room temperature. The successful rehydrogenation of decomposed nano-scale ammonia borane gives guidance to further investigations on hydrogen storage. ^ In addition, the high pressure behavior of lithium amidoborane, one derivative of ammonia borane, was studied at different temperatures. Lithium amidoborane (LAB) was decomposed and recompressed in a diamond anvil cell. After applying high pressures on the decomposed lithium amidoborane, its recovery peaks were discovered by Raman spectroscopy. This result suggests that the decomposition of LAB is reversible at high pressures.^

An investigation into the suitability of time-of-flight mass spectrometry in forensic toxicology

Liquid chromatography coupled with mass spectrometry is one of the most powerful tools in the toxicologist’s arsenal to detect a wide variety of compounds from many different matrices. However, the huge number of potentially abused substances and new substances especially designed as intoxicants poses a problem in a forensic toxicology setting. Most methods are targeted and designed to cover a very specific drug or group of drugs while many other substances remain undetected. High resolution mass spectrometry, more specifically time-of-flight mass spectrometry, represents an extremely powerful tool in analysing a multitude of compounds not only simultaneously but also retroactively. The data obtained through the time-of-flight instrument contains all compounds made available from sample extraction and chromatography, which can be processed at a later time with an improved library to detect previously unrecognised compounds without having to analyse the respective sample again. The aim of this project was to determine the utility and limitations of time-of-flight mass spectrometry as a general and easily expandable screening method. The resolution of time-of-flight mass spectrometry allows for the separation of compounds with the same nominal mass but distinct exact masses without the need to separate them chromatographically. To simulate the wide variety of potentially encountered drugs in such a general screening method, seven drugs (morphine, cocaine, zolpidem, diazepam, amphetamine, MDEA and THC) were chosen to represent this variety in terms of mass, properties and functional groups. Consequently, several liquid-liquid and solid phase extractions were applied to urine samples to determine the most general suitable and unspecific extraction. Chromatography was optimised by investigating the parameters pH, concentration, organic solvent and gradient of the mobile phase to improve data obtained by the time-of-flight instrument. The resulting method was validated as a qualitative confirmation/identification method. Data processing was automated using the software TargetAnalysis, which provides excellent analyte recognition according to retention time, exact mass and isotope pattern. The recognition of isotope patterns allows excellent recognition of analytes even in interference rich mass spectra and proved to be a good positive indicator. Finally, the validated method was applied to samples received from the A& E Department of Glasgow Royal Infirmary in suspected drug abuse cases and samples received from the Scottish Prison Service, which we received from their own prevalence study targeting drugs of abuse in the prison population. The obtained data was processed with a library established in the course of this work.

Synthesis and electronic properties of luminescent silicon nanocrystals and copper indium sulphide quantum dots

In the last decades, nanomaterials, and in particular semiconducting nanoparticles (or quantum dots), have gained increasing attention due to their controllable optical properties and potential applications. Silicon nanoparticles (also called silicon nanocrystals, SiNCs) have been extensively studied in the last years, due to their physical and chemical properties which render them a valid alternative to conventional quantum dots. During my PhD studies I have planned new synthetical routes to obtain SiNCs functionalised with molecules which could ameliorate the properties of the nanoparticle. However, this was certainly challenging, because SiNCs are very susceptible to many reagents and conditions that are often used in organic synthesis. They can be irreversibly quenched in the presence of alkalis, they can be damaged in the presence of oxidants, they can modify their optical properties in the presence of many nitrogen-containing compounds, metal complexes or simple organic molecules. If their surface is not well-passivated, the oxygen can introduce defect states, or they can aggregate and precipitate in several solvents. Therefore, I was able to functionalise SiNCs with different ligands: chromophores, amines, carboxylic acids, poly(ethylene)glycol, even ameliorating functionalisation strategies that already existed. This thesis will collect the experimental procedures used to synthesize silicon nanocrystals, the strategies adopted to functionalise effectively the nanoparticle with different types of organic molecules, and the characterisation of their surface, physical properties and luminescence (mostly photogenerated, but also electrochemigenerated). I also spent a period of 7 months in Leeds (UK), where I managed to learn how to synthesize other cadmium-free quantum dots made of copper, indium and sulphur (CIS QDs). During my last year of PhD, I focused on their functionalisation by ligand exchange techniques, yielding the first example of light-harvesting antenna based on those quantum dots. Part of this thesis is dedicated to them.