Broadband active differential array for the mid-frequency SKA band

This paper presents the design and characterization process of an active array demonstrator for the mid-frequency range (i.e., 300 MHz-1000 MHz) of the future Square Kilometre Array (SKA) radio telescope. This demonstrator, called FIDA3 (FG-IGN: Fundación General Instituto Geográfico Nacional - Differential Active Antenna Array), is part of the Spanish contribution for the SKA project. The main advantages provided by this design include the use of a dielectric-free structure, and the use of a fully-differential receiver in which differential low-noise amplifiers (LNAs) are directly connected to the balanced tapered-slot antennas (TSAs). First, the radiating structure and the differential low-noise amplifiers were separately designed and measured, obtaining good results (antenna elements with low voltage standing-wave ratios, array scanning capabilities up to 45°, and noise temperatures better than 52 K with low-noise amplifiers at room temperature). The potential problems due to the differential nature of the proposed solution are discussed, so some effective methods to overcome such limitations are proposed. Second, the complete active antenna array receiving system was assembled, and a 1 m2 active antenna array tile was characterized.

Smart meter privacy by suprression of low power frequency components

This paper focuses on the problems associated with privacy protection in smart grid. We will give an overview of a possible realization of a privacy-preserving approach that encompasses privacy-utility tradeoff into a single model. This approach proposes suppression of low power frequency components as a solution to reduce the amount of information leakage from smart meter readings. We will consider the applicability of the procedure to hide the appliance usage with respect to the type of home devices.

A Dynamically Adaptable Image Processing Application Trading Off Between High Performance, Consumption and Dependability in Real Time

As embedded systems evolve, problems inherent to technology become important limitations. In less than ten years, chips will exceed the maximum allowed power consumption affecting performance, since, even though the resources available per chip are increasing, frequency of operation has stalled. Besides, as the level of integration is increased, it is difficult to keep defect density under control, so new fault tolerant techniques are required. In this demo work, a new dynamically adaptable virtual architecture (ARTICo3) to allow dynamic and context-aware use of resources is implemented in a high performance Wireless Sensor node (HiReCookie) to perform an image processing application.

Water and nitrogen footprint in an irrigated crop under mineral and organic fertilization

In order to establish rational nitrogen (N) application and reduce groundwater contamination, a clearer understanding of the N distribution through the growing season and its balance is crucial. Excessive doses of N and/or water applied to fertigated crops involve a substantial risk of aquifer contamination by nitrate; but knowledge of N cycling and availability within the soil could assist in avoiding this excess. In central Spain, the main horticultural fertigated crop is the melon type ?piel de sapo¿ and it is cultivated in vulnerable zones to nitrate pollution (Directive 91/676/CEE). However, until few years ago there were not antecedents related to the optimization of nitrogen fertilization together with irrigation. Water and N footprint are indicators that allow assessing the impact generated by different agricultural practices, so they can be used to improve the management strategies in fertigated crop systems. The water footprint distinguishes between blue water (sources of water applied to the crop, like irrigation and precipitation), green water (water used by the crop and stored in the soil), and it is furthermore possible to quantify the impact of pollution by calculating the grey water, which is defined as the volume of polluted water created from the growing and production of crops. On the other hand, the N footprint considers green N (nitrogen consumed by the crops and stored in the soil), blue N (N available for crop, like N applied with mineral and/or organic fertilizers, N applied with irrigation water and N mineralized during the crop period), whereas grey N is the amount of N-NO3- washed from the soil to the aquifer. All these components are expressed as the ratio between the components of water or N footprint and the yield (m3 t-1 or kg N t-1 respectively). The objetives of this work were to evaluate the impact derivated from the use of different fertilizer practices in a melon crop using water and N footprint.

Contribution to Load-Frequency Regulation of a Hydropower Plant with Long Tail-Race Tunnel

In this paper, a hydroelectric power plant with long tail-race tunnel has been modelled for assessing its contribution to secondary regulation reserve. Cavitation problems, caused by the discharge conduit length, are expected downstream the turbine where low pressure appears during regulation manoeuvres. Therefore, governor's gains should be selected taking into account these phenomena. On the other hand, regulation services bidden by the plant operator should fulfil TSO (Transmission System Operator) quality requirements. A methodology for tuning governor PI gains is proposed and applied to a Hydro power plant in pre-design phase in northwest area of Spain. The PI gains adjustment proposed provides a proper plant response, according to some established indexes, while avoiding cavitation phenomena.

Physics of Vibrating Airfoils at Low Reduced Frequency

The unsteady aerodynamics of low pressure turbine vibrating airfoils in flap mode is studied in detail using a frequency domain linearized Navier-Stokes solver. Both the travelling-wave and influence coefficient formulations of the problem are used to highlight key aspects of the physics and understand different trends such as the effect of reduced frequency and Mach number. The study is focused in the low-reduced frequency regime which is of paramount relevance for the design of aeronautical low-pressure turbines and compressors. It is concluded that the effect of the Mach number on the unsteady pressure phase can be neglected in first approximation and that the unsteadiness of the vibrating and adjacent airfoils is driven by vortex shedding mechanisms. Finally a simple model to estimate the work-per-cycle as a function of the reduced frequency and Mach Number is provided. The edge-wise and torsion modes are presented in less detail but it is shown that acoustic waves are essential to explain its behaviour. The non-dimensional work-per-cycle of the edge-wise mode shows a large dependence with the Mach number while in the torsion mode a large number of airfoils is needed to reconstruct the work-per-cycle departing from the influence coefficients.

The Proper Generalized Decomposition With Application In Problems Of Dynamics

In this paper we address the new reduction method called Proper Generalized Decomposition (PGD) which is a discretization technique based on the use of separated representation of the unknown fields, specially well suited for solving multidimensional parametric equations. In this case, it is applied to the solution of dynamics problems. We will focus on the dynamic analysis of an one-dimensional rod with a unit harmonic load of frequency (ω) applied at a point of interest. In what follows, we will present the application of the methodology PGD to the problem in order to approximate the displacement field as the sum of the separated functions. We will consider as new variables of the problem, parameters models associated with the characteristic of the materials, in addition to the frequency. Finally, the quality of the results will be assessed based on an example.

A procedure to track vibration modes under changing external factors: application to a pedestrian bridge

A low-cost vibration monitoring system has been developed and installed on an urban steel- plated stress-ribbon footbridge. The system continuously measures: the acceleration (using 18 triaxial MEMS accelerometers distributed along the structure), the ambient temperature and the wind velocity and direction. Automated output-only modal parameter estimation based on the Stochastic Subspace Identification (SSI) is carried out in order to extract the modal parameters, i.e., the natural frequencies, damping ratios and modal shapes. Thus, this paper analyzes the time evolution of the modal parameters over a whole-year data monitoring. Firstly, for similar environmental/operational factors, the uncertainties associated to the time window size used are studied and quantified. Secondly, a methodology to track the vibration modes has been established since several of them with closely-spaced natural frequencies are identified. Thirdly, the modal parameters have been correlated against external factors. It has been shown that this stress-ribbon structure is highly sensitive to temperature variation (frequency changes of more than 20%) with strongly seasonal and daily trends

Agricultural use of organic wastes as source of nitrogen and phosphorus: risks and opportunities

El nitrógeno (N) y el fósforo (P) son nutrientes esenciales en la producción de cultivos. El desarrollo de los fertilizantes de síntesis durante el siglo XX permitió una intensificación de la agricultura y un aumento de las producciones pero a su vez el gran input de nutrientes ha resultado en algunos casos en sistemas poco eficientes incrementando las pérdidas de estos nutrientes al medio ambiente. En el caso del P, este problema se agrava debido a la escasez de reservas de roca fosfórica necesaria para la fabricación de fertilizantes fosfatados. La utilización de residuos orgánicos en agricultura como fuente de N y P es una buena opción de manejo que permite valorizar la gran cantidad de residuos que se generan. Sin embargo, es importante conocer los procesos que se producen en el suelo tras la aplicación de los mismos, ya que influyen en la disponibilidad de nutrientes que pueden ser utilizados por el cultivo así como en las pérdidas de nutrientes de los agrosistemas que pueden ocasionar problemas de contaminación. Aunque la dinámica del N en el suelo ha sido más estudiada que la del P, los problemas importantes de contaminación por nitratos en zonas vulnerables hacen necesaria la evaluación de aquellas prácticas de manejo que pudieran agravar esta situación, y en el caso de los residuos orgánicos, la evaluación de la respuesta agronómica y medioambiental de la aplicación de materiales con un alto contenido en N (como los residuos procedentes de la industria vinícola y alcoholera). En cuanto al P, debido a la mayor complejidad de su ciclo y de las reacciones que ocurren en el suelo, hay un mayor desconocimiento de los factores que influyen en su dinámica en los sistemas suelo-planta, lo que supone nuevas oportunidades de estudio en la evaluación del uso agrícola de los residuos orgánicos. Teniendo en cuenta los conocimientos previos sobre cada nutriente así como las necesidades específicas en el estudio de los mismos, en esta Tesis se han evaluado: (1) el efecto de la aplicación de residuos procedentes de la industria vinícola y alcoholera en la dinámica del N desde el punto de vista agronómico y medioambiental en una zona vulnerable a la contaminación por nitratos; y (2) los factores que influyen en la disponibilidad de P en el suelo tras la aplicación de residuos orgánicos. Para ello se han llevado a cabo incubaciones de laboratorio así como ensayos de campo que permitieran evaluar la dinámica de estos nutrientes en condiciones reales. Las incubaciones de suelo en condiciones controladas de humedad y temperatura para determinar el N mineralizado se utilizan habitualmente para estimar la disponibilidad de N para el cultivo así como el riesgo medioambiental. Por ello se llevó a cabo una incubación en laboratorio para conocer la velocidad de mineralización de N de un compost obtenido a partir de residuos de la industria vinícola y alcoholera, ampliamente distribuida en Castilla-La Mancha, región con problemas importantes de contaminación de acuíferos por nitratos. Se probaron tres dosis crecientes de compost correspondientes a 230, 460 y 690 kg de N total por hectárea que se mezclaron con un suelo franco arcillo arenoso de la zona. La evolución del N mineral en el suelo a lo largo del tiempo se ajustó a un modelo de regresión no lineal, obteniendo valores bajos de N potencialmente mineralizable y bajas contantes de mineralización, lo que indica que se trata de un material resistente a la mineralización y con una lenta liberación de N en el suelo, mineralizándose tan solo 1.61, 1.33 y 1.21% del N total aplicado con cada dosis creciente de compost (para un periodo de seis meses). Por otra parte, la mineralización de N tras la aplicación de este material también se evaluó en condiciones de campo, mediante la elaboración de un balance de N durante dos ciclos de cultivo (2011 y 2012) de melón bajo riego por goteo, cultivo y manejo agrícola muy característicos de la zona de estudio. Las constantes de mineralización obtenidas en el laboratorio se ajustaron a las temperaturas reales en campo para predecir el N mineralizado en campo durante el ciclo de cultivo del melón, sin embargo este modelo generalmente sobreestimaba el N mineralizado observado en campo, por la influencia de otros factores no tenidos en cuenta para obtener esta predicción, como el N acumulado en el suelo, el efecto de la planta o las fluctuaciones de temperatura y humedad. Tanto el ajuste de los datos del laboratorio al modelo de mineralización como las predicciones del mismo fueron mejores cuando se consideraba el efecto de la mezcla suelo-compost que cuando se aislaba el N mineralizado del compost, mostrando la importancia del efecto del suelo en la mineralización del N procedente de residuos orgánicos. Dado que esta zona de estudio ha sido declarada vulnerable a la contaminación por nitratos y cuenta con diferentes unidades hidrológicas protegidas, en el mismo ensayo de campo con melón bajo riego por goteo se evaluó el riesgo de contaminación por nitratos tras la aplicación de diferentes dosis de compost bajo dos regímenes de riego, riego ajustado a las necesidades del cultivo (90 ó 100% de la evapotranspiración del cultivo (ETc)) o riego excedentario (120% ETc). A lo largo del ciclo de cultivo se estimó semanalmente el drenaje mediante la realización de un balance hídrico, así como se tomaron muestras de la solución de suelo y se determinó su concentración de nitratos. Para evaluar el riesgo de contaminación de las aguas subterráneas asociado con estas prácticas, se utilizaron algunos índices medioambientales para determinar la variación en la calidad del agua potable (Índice de Impacto (II)) y en la concentración de nitratos del acuífero (Índice de Impacto Ambiental (EII)). Para combinar parámetros medioambientales con parámetros de producción, se calculó la eficiencia de manejo. Se observó que la aplicación de compost bajo un régimen de riego ajustado no aumentaba el riesgo de contaminación de las aguas subterráneas incluso con la aplicación de la dosis más alta. Sin embargo, la aplicación de grandes cantidades de compost combinada con un riego excedentario supuso un incremento en el N lixiviado a lo largo del ciclo de cultivo, mientras que no se obtuvieron mayores producciones con respecto al riego ajustado. La aplicación de residuos de la industria vinícola y alcoholera como fuente de P fue evaluada en suelos calizos caracterizados por una alta capacidad de retención de P, lo cual en algunos casos limita la disponibilidad de este nutriente. Para ello se llevó a cabo otro ensayo de incubación con dos suelos de diferente textura, con diferente contenido de carbonato cálcico, hierro y con dos niveles de P disponible; a los que se aplicaron diferentes materiales procedentes de estas industrias (con y sin compostaje previo) aportando diferentes cantidades de P. A lo largo del tiempo se analizó el P disponible del suelo (P Olsen) así como el pH y el carbono orgánico disuelto. Al final de la incubación, con el fin de estudiar los cambios producidos por los diferentes residuos en el estado del P del suelo se llevó a cabo un fraccionamiento del P inorgánico del suelo, el cual se separó en P soluble y débilmente enlazado (NaOH-NaCl-P), P soluble en reductores u ocluido en los óxidos de Fe (CBD-P) y P poco soluble precipitado como Ca-P (HCl-P); y se determinó la capacidad de retención de P así como el grado de saturación de este elemento en el suelo. En este ensayo se observó que, dada la naturaleza caliza de los suelos, la influencia de la cantidad de P aplicado con los residuos en el P disponible sólo se producía al comienzo del periodo de incubación, mientras que al final del ensayo el incremento en el P disponible del suelo se igualaba independientemente del P aplicado con cada residuo, aumentando el P retenido en la fracción menos soluble con el aumento del P aplicado. Por el contrario, la aplicación de materiales orgánicos menos estabilizados y con un menor contenido en P, produjo un aumento en las formas de P más lábiles debido a una disolución del P retenido en la fracción menos lábil, lo cual demostró la influencia de la materia orgánica en los procesos que controlan el P disponible en el suelo. La aplicación de residuos aumentó el grado de saturación de P de los suelos, sin embargo los valores obtenidos no superaron los límites establecidos que indican un riesgo de contaminación de las aguas. La influencia de la aplicación de residuos orgánicos en las formas de P inorgánico y orgánico del suelo se estudió además en un suelo ácido de textura areno francosa tras la aplicación en campo a largo plazo de estiércol vacuno y de compost obtenido a partir de biorresiduos, así como la aplicación combinada de compost y un fertilizante mineral (superfosfato tripe), en una rotación de cultivos. En muestras de suelo recogidas 14 años después del establecimiento del experimento en campo, se determinó el P soluble y disponible, la capacidad de adsorción de P, el grado de saturación de P así como diferentes actividades enzimáticas (actividad deshidrogenasa, fosfatasa ácida y fosfatasa alcalina). Las diferentes formas de P orgánico en el suelo se estudiaron mediante una técnica de adición de enzimas con diferentes substratos específicos a extractos de suelo de NaOH-EDTA, midiendo el P hidrolizado durante un periodo de incubación por colorimetría. Las enzimas utilizadas fueron la fosfatasa ácida, la nucleasa y la fitasa las cuales permitieron identificar monoésteres hidrolizables (monoester-like P), diésteres (DNA-like P) e inositol hexaquifosfato (Ins6P-like P). La aplicación a largo plazo de residuos orgánicos aumentó el P disponible del suelo proporcionalmente al P aplicado con cada tipo de fertilización, suponiendo un mayor riesgo de pérdidas de P dado el alto grado de saturación de este suelo. La aplicación de residuos orgánicos aumentó el P orgánico del suelo resistente a la hidrólisis enzimática, sin embargo no influyó en las diferentes formas de P hidrolizable por las enzimas en comparación con las observadas en el suelo sin enmendar. Además, las diferentes formas de P orgánico aplicadas con los residuos orgánicos no se correspondieron con las analizadas en el suelo lo cual demostró que éstas son el resultado de diferentes procesos en el suelo mediados por las plantas, los microorganismos u otros procesos abióticos. En este estudio se encontró una correlación entre el Ins6P-like P y la actividad microbiana (actividad deshidrogenasa) del suelo, lo cual refuerza esta afirmación. Por último, la aplicación de residuos orgánicos como fuente de N y P en la agricultura se evaluó agronómicamente en un escenario real. Se estableció un experimento de campo para evaluar el compost procedente de residuos de bodegas y alcoholeras en el mismo cultivo de melón utilizado en el estudio de la mineralización y lixiviación de N. En este experimento se estudió la aplicación de tres dosis de compost: 1, 2 y 3 kg de compost por metro lineal de plantación correspondientes a 7, 13 y 20 t de compost por hectárea respectivamente; y se estudió el efecto sobre el crecimiento de las plantas, la acumulación de N y P en la planta, así como la producción y calidad del cultivo. La aplicación del compost produjo un ligero incremento en la biomasa vegetal acompañado por una mejora significativa de la producción con respecto a las parcelas no enmendadas, obteniéndose la máxima producción con la aplicación de 2 kg de compost por metro lineal. Aunque los efectos potenciales del N y P fueron parcialmente enmascarados por otras entradas de estos nutrientes en el sistema (alta concentración de nitratos en el agua de riego y ácido fosfórico suministrado por fertirrigación), se observó una mayor acumulación de P uno de los años de estudio que resultó en un aumento en el número de frutos en las parcelas enmendadas. Además, la mayor acumulación de N y P disponible en el suelo al final del ciclo de cultivo indicó el potencial uso de estos materiales como fuente de estos nutrientes. ABSTRACT Nitrogen (N) and phosphorus (P) are essential nutrients in crop production. The development of synthetic fertilizers during the 20th century allowed an intensification of the agriculture increasing crop yields but in turn the great input of nutrients has resulted in some cases in inefficient systems with higher losses to the environment. Regarding P, the scarcity of phosphate rock reserves necessary for the production of phosphate fertilizers aggravates this problem. The use of organic wastes in agriculture as a source of N and P is a good option of management that allows to value the large amount of wastes generated. However, it is important to understand the processes occurring in the soil after application of these materials, as they affect the availability of nutrients that can be used by the crop and the nutrient losses from agricultural systems that can cause problems of contamination. Although soil N dynamic has been more studied than P, the important concern of nitrate pollution in Nitrate Vulnerable Zones requires the evaluation of those management practices that could aggravate this situation, and in the case of organic wastes, the evaluation of the agronomic and environmental response after application of materials with a high N content (such as wastes from winery and distillery industries). On the other hand, due to the complexity of soil P cycle and the reactions that occur in soil, there is less knowledge about the factors that can influence its dynamics in the soil-plant system, which means new opportunities of study regarding the evaluation of the agricultural use of organic wastes. Taking into account the previous knowledge of each nutrient and the specific needs of study, in this Thesis we have evaluated: (1) the effect of the application of wastes from the winery and distillery industries on N dynamics from the agronomic and environmental viewpoint in a vulnerable zone; and (2) the factors that influence P availability in soils after the application of organic wastes. With this purposes, incubations were carried out in laboratory conditions as well as field trials that allow to assess the dynamic of these nutrients in real conditions. Soil incubations under controlled moisture and temperature conditions to determine N mineralization are commonly used to estimate N availability for crops together with the environmental risk. Therefore, a laboratory incubation was conducted in order to determine the N mineralization rate of a compost made from wastes generated in the winery and distillery industries, widely distributed in Castilla-La Mancha, a region with significant problems of aquifers contamination by nitrates. Three increasing doses of compost corresponding to 230, 460 and 690 kg of total N per hectare were mixed with a sandy clay loam soil collected in this area. The evolution of mineral N in soil over time was adjusted to a nonlinear regression model, obtaining low values of potentially mineralizable N and low constants of mineralization, indicating that it is a material resistant to mineralization with a slow release of N, with only 1.61, 1.33 and 1.21% of total N applied being mineralized with each increasing dose of compost (for a period of six months). Furthermore, N mineralization after the application of this material was also evaluated in field conditions by carrying out a N balance during two growing seasons (2011 and 2012) of a melon crop under drip irrigation, a crop and management very characteristic of the area of study. The mineralization constants obtained in the laboratory were adjusted to the actual temperatures observed in the field to predict N mineralized during each growing season, however, this model generally overestimated the N mineralization observed in the field, because of the influence of other factors not taken into account for this prediction, as N accumulated in soil, the plant effect or the fluctuations of temperature and moisture. The fitting of the laboratory data to the model as well as the predictions of N mineralized in the field were better when considering N mineralized from the soil-compost mixture rather than when N mineralized from compost was isolated, underlining the important role of the soil on N mineralization from organic wastes. Since the area of study was declared vulnerable to nitrate pollution and is situated between different protected hydrological units, the risk of nitrate pollution after application of different doses compost was evaluated in the same field trial with melon under two irrigation regimes, irrigation adjusted to the crop needs (90 or 100% of the crop evapotranspiration (ETc)) or excedentary irrigation (120% ETc). Drainage was estimated weekly throughout the growing season by conducting a water balance, samples of the soil solution were taken and the concentration of nitrates was determined. To assess the risk of groundwater contamination associated with these practices, some environmental indices were used to determine the variation in the quality of drinking water (Impact Index (II)) and the nitrates concentration in the groundwater (Environmental Impact Index (EII)). To combine environmental parameters together with yield parameters, the Management Efficiency was calculated. It was observed that the application of compost under irrigation adjusted to the plant needs did not represent a higher risk of groundwater contamination even with the application of the highest doses. However, the application of large amounts of compost combined with an irrigation surplus represented an increase of N leaching during the growing season compared with the unamended plots, while no additional yield with respect to the adjusted irrigation strategy is obtained. The application of wastes derived from the winery and distillery industry as source of P was evaluated in calcareous soils characterized by a high P retention capacity, which in some cases limits the availability of this nutrient. Another incubation experiment was carried out using two soils with different texture, different calcium carbonate and iron contents and two levels of available P; to which different materials from these industries (with and without composting) were applied providing different amounts of P. Soil available P (Olsen P), pH and dissolved organic carbon were analyzed along time. At the end of the incubation, in order to study the changes in soil P status caused by the different residues, a fractionation of soil inorganic P was carried out, which was separated into soluble and weakly bound P (NaOH-NaCl- P), reductant soluble P or occluded in Fe oxides (CBD-P) and P precipitated as poorly soluble Ca-P (HCl-P); and the P retention capacity and degree of P saturation were determined as well. Given the calcareous nature of the soils, the influence of the amount of P applied with the organic wastes in soil available P only occurred at the beginning of the incubation period, while at the end of the trial the increase in soil available P equalled independently of the amount of P applied with each residue, increasing the P retained in the least soluble fraction when increasing P applied. Conversely, the application of less stabilized materials with a lower content of P resulted in an increase in the most labile P forms due to dissolution of P retained in the less labile fraction, demonstrating the influence of organic matter addition on soil P processes that control P availability in soil. As expected, the application of organic wastes increased the degree of P saturation in the soils, however the values obtained did not exceed the limits considered to pose a risk of water pollution. The influence of the application of organic wastes on inorganic and organic soil P forms was also studied in an acid loamy sand soil after long-term field application of cattle manure and biowaste compost and the combined application of compost and mineral fertilizer (triple superphosphate) in a crop rotation. Soil samples were collected 14 years after the establishment of the field experiment, and analyzed for soluble and available P, P sorption capacity, degree of P saturation and enzymatic activities (dehydrogenase, acid phosphatase and alkaline phosphatase). The different forms of organic P in soil were determined by using an enzyme addition technique, based on adding enzymes with different substrate specificities to NaOH-EDTA soil extracts, measuring the hydrolyzed P colorimetrically after an incubation period. The enzymes used were acid phosphatase, nuclease and phytase which allowed to identify hydrolyzable monoesters (monoester-like P) diesters (DNA-like P) and inositol hexakisphosphate (Ins6P-like P). The long-term application of organic wastes increased soil available P proportionally to the P applied with each type of fertilizer, assuming a higher risk of P losses given the high degree of P saturation of this soil. The application of organic wastes increased soil organic P resistant to enzymatic hydrolysis, but no influence was observed regarding the different forms of enzyme hydrolyzable organic P compared to those observed in the non-amended soil. Furthermore, the different forms of organic P applied with the organic wastes did not correspond to those analyzed in the soil which showed that these forms in soil are a result of multifaceted P turnover processes in soil affected by plants, microorganisms and abiotic factors. In this study, a correlation between Ins6P-like P and the microbial activity (dehydrogenase activity) of soil was found, which reinforces this claim. Finally, the application of organic wastes as a source of N and P in agriculture was evaluated agronomically in a real field scenario. A field experiment was established to evaluate the application of compost made from wine-distillery wastes in the same melon crop used in the experiments of N mineralization and leaching. In this experiment the application of three doses of compost were studied: 1 , 2 and 3 kg of compost per linear meter of plantation corresponding to 7, 13 and 20 tonnes of compost per hectare respectively; and the effect on plant growth, N and P accumulation in the plant as well as crop yield and quality was studied. The application of compost produced a slight increase in plant biomass accompanied by a significant improvement in crop yield with respect to the unamended plots, obtaining the maximum yield with the application of 2 kg of compost per linear meter. Although the potential effects of N and P were partially masked by other inputs of these nutrients in the system (high concentration of nitrates in the irrigation water and phosphoric acid supplied by fertigation), an effect of P was observed the first year of study resulting in a greater plant P accumulation and in an increase in the number of fruits in the amended plots. In addition, the higher accumulation of available N and P in the topsoil at the end of the growing season indicated the potential use of this material as source of these nutrients.

Frequency control support of a wind-solar isolated system by a hydropower plant with long tail-race tunnel

Pumped storage hydro plants (PSHP) can provide adequate energy storage and frequency regulation capacities in isolated power systems having significant renewable energy resources. Due to its high wind and solar potential, several plans have been developed for La Palma Island in the Canary archipelago, aimed at increasing the penetration of these energy sources. In this paper, the performance of the frequency control of La Palma power system is assessed, when the demand is supplied by the available wind and solar generation with the support of a PSHP which has been predesigned for this purpose. The frequency regulation is provided exclusively by the PSHP. Due to topographic and environmental constraints, this plant has a long tail-race tunnel without a surge tank. In this configuration, the effects of pressure waves cannot be neglected and, therefore, usual recommendations for PID governor tuning provide poor performance. A PI governor tuning criterion is proposed for the hydro plant and compared with other criteria according to several performance indices. Several scenarios considering solar and wind energy penetration have been simulated to check the plant response using the proposed criterion. This tuning of the PI governor maintains La Palma system frequency within grid code requirements.

Field-winding fault detection in synchronous machines with static excitation through frequency response analysis.

Frequency Response Analysis is a well-known technique for the diagnosis of power transformers. Currently, this technique is under research for its application in rotary electrical machines. This paper presents significant results on the application of Frequency Response Analysis to fault detection in field winding of synchronous machines with static excitation. First, the influence of the rotor position on the frequency response is evaluated. Secondly, some relevant test results are shown regarding ground fault and inter-turn fault detection in field windings at standstill condition. The influence of the fault resistance value is also taken into account. This paper also studies the applicability of Frequency Response Analysis in fault detection in field windings while rotating. This represents an important feature because some defects only appear with the machine rated speed. Several laboratory test results show the applicability of this fault detection technique in field windings at full speed with no excitation current.

The crystal structure of the nitrogen regulation fragment of the yeast prion protein Ure2p

The yeast nonchromosomal gene [URE3] is due to a prion form of the nitrogen regulatory protein Ure2p. It is a negative regulator of nitrogen catabolism and acts by inhibiting the transcription factor Gln3p. Ure2p residues 1–80 are necessary for prion generation and propagation. The C-terminal fragment retains nitrogen regulatory activity, albeit somewhat less efficiently than the full-length protein, and it also lowers the frequency of prion generation. The crystal structure of this C-terminal fragment, Ure2p(97–354), at 2.3 Å resolution is described here. It adopts the same fold as the glutathione S-transferase superfamily, consistent with their sequence similarity. However, Ure2p(97–354) lacks a properly positioned catalytic residue that is required for S-transferase activity. Residues within this regulatory fragment that have been indicated by mutational studies to influence prion generation have been mapped onto the three-dimensional structure, and possible implications for prion activity are discussed.

A novel application of gene arrays: Escherichia coli array provides insight into the biology of the obligate endosymbiont of tsetse flies

Symbiotic associations with microorganisms are pivotal in many insects. Yet, the functional roles of obligate symbionts have been difficult to study because it has not been possible to cultivate these organisms in vitro. The medically important tsetse fly (Diptera: Glossinidae) relies on its obligate endosymbiont, Wigglesworthia glossinidia, a member of the Enterobacteriaceae, closely related to Escherichia coli, for fertility and possibly nutrition. We show here that the intracellular Wigglesworthia has a reduced genome size smaller than 770 kb. In an attempt to understand the composition of its genome, we used the gene arrays developed for E. coli. We were able to identify 650 orthologous genes in Wigglesworthia corresponding to ≈85% of its genome. The arrays were also applied for expression analysis using Wigglesworthia cDNA and 61 gene products were detected, presumably coding for some of its most abundant products. Overall, genes involved in cell processes, DNA replication, transcription, and translation were found largely retained in the small genome of Wigglesworthia. In addition, genes coding for transport proteins, chaperones, biosynthesis of cofactors, and some amino acids were found to comprise a significant portion, suggesting an important role for these proteins in its symbiotic life. Based on its expression profile, we predict that Wigglesworthia may be a facultative anaerobic organism that utilizes ammonia as its major source of nitrogen. We present an application of E. coli gene arrays to obtain broad genome information for a closely related organism in the absence of complete genome sequence data.

Toward antibody-directed "abzyme" prodrug therapy, ADAPT: carbamate prodrug activation by a catalytic antibody and its in vitro application to human tumor cell killing.

Antibody-directed enzyme prodrug therapy, ADEPT, is a recent approach to targeted cancer chemotherapy intended to diminish the nonspecific toxicity associated with many commonly used chemotherapeutic agents. Most ADEPT systems incorporate a bacterial enzyme, and thus their potential is reduced because of the immunogenicity of that component of the conjugate. This limitation can be circumvented by the use of a catalytic antibody, which can be "humanized," in place of the bacterial enzyme catalyst. We have explored the scope of such antibody-directed "abzyme" prodrug therapy, ADAPT, to evaluate the potential for a repeatable targeted cancer chemotherapy. We report the production of a catalytic antibody that can hydrolyze the carbamate prodrug 4-[N,N-bis(2-chloroethyl)]aminophenyl-N-[(1S)-(1,3- dicarboxy)propyl]carbamate (1) to generate the corresponding cytotoxic nitrogen mustard (Km = 201 microM, kcat = 1.88 min-1). In vitro studies with this abzyme, EA11-D7, and prodrug 1 lead to a marked reduction in viability of cultured human colonic carcinoma (LoVo) cells relative to appropriate controls. In addition, we have found a good correlation between antibody catalysis as determined by this cytotoxicity assay in vitro and competitive binding studies of candidate abzymes to the truncated transition-state analogue ethyl 4-nitrophenylmethylphosphonate. This cell-kill assay heralds a general approach to direct and rapid screening of antibody libraries for catalysts.

Real time optimization in chemical process: evaluation of strategies, improvements and industrial application.

The increasing economic competition drives the industry to implement tools that improve their processes efficiencies. The process automation is one of these tools, and the Real Time Optimization (RTO) is an automation methodology that considers economic aspects to update the process control in accordance with market prices and disturbances. Basically, RTO uses a steady-state phenomenological model to predict the process behavior, and then, optimizes an economic objective function subject to this model. Although largely implemented in industry, there is not a general agreement about the benefits of implementing RTO due to some limitations discussed in the present work: structural plant/model mismatch, identifiability issues and low frequency of set points update. Some alternative RTO approaches have been proposed in literature to handle the problem of structural plant/model mismatch. However, there is not a sensible comparison evaluating the scope and limitations of these RTO approaches under different aspects. For this reason, the classical two-step method is compared to more recently derivative-based methods (Modifier Adaptation, Integrated System Optimization and Parameter estimation, and Sufficient Conditions of Feasibility and Optimality) using a Monte Carlo methodology. The results of this comparison show that the classical RTO method is consistent, providing a model flexible enough to represent the process topology, a parameter estimation method appropriate to handle measurement noise characteristics and a method to improve the sample information quality. At each iteration, the RTO methodology updates some key parameter of the model, where it is possible to observe identifiability issues caused by lack of measurements and measurement noise, resulting in bad prediction ability. Therefore, four different parameter estimation approaches (Rotational Discrimination, Automatic Selection and Parameter estimation, Reparametrization via Differential Geometry and classical nonlinear Least Square) are evaluated with respect to their prediction accuracy, robustness and speed. The results show that the Rotational Discrimination method is the most suitable to be implemented in a RTO framework, since it requires less a priori information, it is simple to be implemented and avoid the overfitting caused by the Least Square method. The third RTO drawback discussed in the present thesis is the low frequency of set points update, this problem increases the period in which the process operates at suboptimum conditions. An alternative to handle this problem is proposed in this thesis, by integrating the classic RTO and Self-Optimizing control (SOC) using a new Model Predictive Control strategy. The new approach demonstrates that it is possible to reduce the problem of low frequency of set points updates, improving the economic performance. Finally, the practical aspects of the RTO implementation are carried out in an industrial case study, a Vapor Recompression Distillation (VRD) process located in Paulínea refinery from Petrobras. The conclusions of this study suggest that the model parameters are successfully estimated by the Rotational Discrimination method; the RTO is able to improve the process profit in about 3%, equivalent to 2 million dollars per year; and the integration of SOC and RTO may be an interesting control alternative for the VRD process.