General electromagnetic simulation tool to predict the microwave nonlinear response of planar, arbitrarily-shaped HTS structures

This work describes a simulation tool being developed at UPC to predict the microwave nonlinear behavior of planar superconducting structures with very few restrictions on the geometry of the planar layout. The software is intended to be applicable to most structures used in planar HTS circuits, including line, patch, and quasi-lumped microstrip resonators. The tool combines Method of Moments (MoM) algorithms for general electromagnetic simulation with Harmonic Balance algorithms to take into account the nonlinearities in the HTS material. The Method of Moments code is based on discretization of the Electric Field Integral Equation in Rao, Wilton and Glisson Basis Functions. The multilayer dyadic Green's function is used with Sommerfeld integral formulation. The Harmonic Balance algorithm has been adapted to this application where the nonlinearity is distributed and where compatibility with the MoM algorithm is required. Tests of the algorithm in TM010 disk resonators agree with closed-form equations for both the fundamental and third-order intermodulation currents. Simulations of hairpin resonators show good qualitative agreement with previously published results, but it is found that a finer meshing would be necessary to get correct quantitative results. Possible improvements are suggested.

Performance Characteristics of an Axial-Flux Solid-Rotor-Core Induction Motor

The integration of electric motors and industrial appliances such as pumps, fans, and compressors is rapidly increasing. For instance, the integration of an electric motor and a centrifugal pump provides cost savings and improved performance characteristics. Material cost savings are achieved when an electric motor is integrated into the shaft of a centrifugal pump, and the motor utilizes the bearings of the pump. This arrangement leads to a smaller configuration that occupies less floor space. The performance characteristics of a pump drive can be improved by using the variable-speed technology. This enables the full speed control of the drive and the absence of a mechanical gearbox and couplers. When using rotational speeds higher than those that can be directly achieved by the network frequency the structure of the rotor has to be mechanically durable. In this thesis the performance characteristics of an axial-flux solid-rotor-core induction motor are determined. The motor studied is a one-rotor-one-stator axial-flux induction motor, and thus, there is only one air-gap between the rotor and the stator. The motor was designed for higher rotational speeds, and therefore a good mechanical strength of the solid-rotor-core rotor is required to withstand the mechanical stresses. The construction of the rotor and the high rotational speeds together produce a feature, which is not typical of traditional induction motors: the dominating loss component of the motor is the rotor eddy current loss. In the case of a typical industrial induction motor instead the dominating loss component is the stator copper loss. In this thesis, several methods to decrease the rotor eddy current losses in the case of axial-flux induction motors are presented. A prototype motor with 45 kW output power at 6000 min-1 was designed and constructed for ascertaining the results obtained from the numerical FEM calculations. In general, this thesis concentrates on the methods for improving the electromagnetic properties of an axial-flux solid-rotor-core induction motor and examines the methods for decreasing the harmonic eddy currents of the rotor. The target is to improve the efficiency of the motor and to reach the efficiency standard of the present-day industrial induction motors equipped with laminated rotors.

Reconstruction of the join time-delay Doppler-scale reflectivity density in the wide-band regime. A frame theory based approach

The inverse scattering problem concerning the determination of the joint time-delayDoppler-scale reflectivity density characterizing continuous target environments is addressed by recourse to the generalized frame theory. A reconstruction formula,involving the echoes of a frame of outgoing signals and its corresponding reciprocalframe, is developed. A ‘‘realistic’’ situation with respect to the transmission ofa finite number of signals is further considered. In such a case, our reconstruction formula is shown to yield the orthogonal projection of the reflectivity density onto a subspace generated by the transmitted signals.

Paperitehtaan kunnossapitoprosessien gap -analyysi

Tässä diplomityössä käsitellään paperitehtaan kunnossapitoprosessien hallintaa ja niiden uudistamista yrityksen strategisista lähtökohdista. Diplomityön tavoitteena on etsiä merkittävimmät poikkeamat toimintojen nykytilan ja strategiassa määritellyn tavoitetilan välillä, ja tämän perusteella esittää kehitysehdotuksia toimintojen parantamiseksi. Tutkimuksen kirjallisessa osassa tutkimusongelmaa käsitellään prosessien kuvaamisen, ydinprosessien määrittelemisen ja toimintamallimuutoksen käyttöönoton näkökulmasta. Lisäksi kirjallisissa lähteissä hyödynnetään kunnossapidon johtamisen ajatuksia. Diplomityön empiirisessä osassa toteutetaan haastattelututkimus kohdeyrityksen kunnossapito-organisaatiossa sekä benchmark -tyyppinen haastattelu ulkopuolisessa yrityksessä. Tutkimuksen tulokset osoittavat, että kunnossapitotoimintojen toteuttaminen on hajanaista niin yrityksen strategiaan kuin osastojen väliseen toimintaan suhteutettuna. Näiden tulosten perusteella suositellaan johdolle aktiivisempaa otetta toimintamallimuutoksen loppuunsaattamiseen.

Electromagnetic Design of a Solid Steel Rotor Motor for Demanding Operation Environments

The solid-rotor induction motor provides a mechanically and thermally reliable solution for demanding environments where other rotor solutions are prohibited or questionable. Solid rotors, which are manufactured of single pieces of ferromagnetic material, are commonly used in motors in which the rotationspeeds exceed substantially the conventional speeds of laminated rotors with squirrel-cage. During the operation of a solid-rotor electrical machine, the rotor core forms a conductor for both the magnetic flux and the electrical current. This causes an increase in the rotor resistance and rotor leakage inductance, which essentially decreases the power factor and the efficiency of the machine. The electromagnetic problems related to the solid-rotor induction motor are mostly associated with the low performance of the rotor. Therefore, the main emphasis in this thesis is put on the solid steel rotor designs. The rotor designs studied in thisthesis are based on the fact that the rotor construction should be extremely robust and reliable to withstand the high mechanical stresses caused by the rotational velocity of the rotor. In addition, the demanding operation environment sets requirements for the applied materials because of the high temperatures and oxidizing acids, which may be present in the cooling fluid. Therefore, the solid rotors analyzed in this thesis are made of a single piece of ferromagnetic material without any additional parts, such as copper end-rings or a squirrel-cage. A pure solid rotor construction is rigid and able to keep its balance over a large speed range. It also may tolerate other environmental stresses such as corroding substances or abrasive particles. In this thesis, the main target is to improve the performance of an induction motor equipped with a solid steel rotor by traditional methods: by axial slitting of the rotor, by selecting a proper rotor core material and by coating the rotor with a high-resistive stainless ferromagnetic material. In the solid steel rotor calculation, the rotor end-effects have a significant effect on the rotor characteristics. Thus, the emphasis is also put on the comparison of different rotor endfactors. In addition, a corrective slip-dependent end-factor is proposed. The rotor designs covered in this thesis are the smooth solid rotor, the axially slitted solid rotor and the slitted rotor having a uniform ferromagnetic coating cylinder. The thesis aims at design rules for multi-megawatt machines. Typically, mega-watt-size solidrotor machines find their applications mainly in the field of electric-motor-gas-compression systems, in steam-turbine applications, and in various types of largepower pump applications, where high operational speeds are required. In this thesis, a 120 kW, 10 000 rpm solid-rotor induction motor is usedas a small-scale model for such megawatt-range solid-rotor machines. The performance of the 120 kW solid-rotor induction motors is determined by experimental measurements and finite element calculations.

Numerical and ExperimentalModelling of Gas Flow and Heat Transfer in the Air Gap of An Electric Machine

This work deals with the cooling of high-speed electric machines, such as motors and generators, through an air gap. It consists of numerical and experimental modelling of gas flow and heat transfer in an annular channel. Velocity and temperature profiles are modelled in the air gap of a high-speed testmachine. Local and mean heat transfer coefficients and total friction coefficients are attained for a smooth rotor-stator combination at a large velocity range. The aim is to solve the heat transfer numerically and experimentally. The FINFLO software, developed at Helsinki University of Technology, has been used in the flow solution, and the commercial IGG and Field view programs for the grid generation and post processing. The annular channel is discretized as a sector mesh. Calculation is performed with constant mass flow rate on six rotational speeds. The effect of turbulence is calculated using three turbulence models. The friction coefficient and velocity factor are attained via total friction power. The first part of experimental section consists of finding the proper sensors and calibrating them in a straight pipe. After preliminary tests, a RdF-sensor is glued on the walls of stator and rotor surfaces. Telemetry is needed to be able to measure the heat transfer coefficients at the rotor. The mean heat transfer coefficients are measured in a test machine on four cooling air mass flow rates at a wide Couette Reynolds number range. The calculated values concerning the friction and heat transfer coefficients are compared with measured and semi-empirical data. Heat is transferred from the hotter stator and rotor surfaces to the coolerair flow in the air gap, not from the rotor to the stator via the air gap, althought the stator temperature is lower than the rotor temperature. The calculatedfriction coefficients fits well with the semi-empirical equations and precedingmeasurements. On constant mass flow rate the rotor heat transfer coefficient attains a saturation point at a higher rotational speed, while the heat transfer coefficient of the stator grows uniformly. The magnitudes of the heat transfer coefficients are almost constant with different turbulence models. The calibrationof sensors in a straight pipe is only an advisory step in the selection process. Telemetry is tested in the pipe conditions and compared to the same measurements with a plain sensor. The magnitudes of the measured data and the data from the semi-empirical equation are higher for the heat transfer coefficients than thenumerical data considered on the velocity range. Friction and heat transfer coefficients are presented in a large velocity range in the report. The goals are reached acceptably using numerical and experimental research. The next challenge is to achieve results for grooved stator-rotor combinations. The work contains also results for an air gap with a grooved stator with 36 slots. The velocity field by the numerical method does not match in every respect the estimated flow mode. The absence of secondary Taylor vortices is evident when using time averagednumerical simulation.

Design of axial-flux permanent-magnet low-speed machines and performance comparison between radial-flux and axial-flux machines

This thesis presents an alternative approach to the analytical design of surface-mounted axialflux permanent-magnet machines. Emphasis has been placed on the design of axial-flux machines with a one-rotor-two-stators configuration. The design model developed in this study incorporates facilities to include both the electromagnetic design and thermal design of the machine as well as to take into consideration the complexity of the permanent-magnet shapes, which is a typical requirement for the design of high-performance permanent-magnet motors. A prototype machine with rated 5 kW output power at 300 min-1 rotation speed has been designed and constructed for the purposesof ascertaining the results obtained from the analytical design model. A comparative study of low-speed axial-flux and low-speed radial-flux permanent-magnet machines is presented. The comparative study concentrates on 55 kW machines with rotation speeds 150 min-1, 300 min-1 and 600 min-1 and is based on calculated designs. A novel comparison method is introduced. The method takes into account the mechanical constraints of the machine and enables comparison of the designed machines, with respect to the volume, efficiency and cost aspects of each machine. It is shown that an axial-flux permanent-magnet machine with one-rotor-two-stators configuration has generally a weaker efficiency than a radial-flux permanent-magnet machine if for all designs the same electric loading, air-gap flux density and current density have been applied. On the other hand, axial-flux machines are usually smaller in volume, especially when compared to radial-flux machines for which the length ratio (axial length of stator stack vs. air-gap diameter)is below 0.5. The comparison results show also that radial-flux machines with alow number of pole pairs, p < 4, outperform the corresponding axial-flux machines.

Investigation of interaction between native and impurity defects in ZnSe

Zinc selenide is a prospective material for optoelectronics. The fabrication of ZnSe­based light-emitting diodes is hindered by complexity of p-type doping of the component materials. The interaction between native and impurity defects, the tendency of doping impurity to form associative centres with native defects and the tendency to self-compensation are the main factors impeding effective control of the value and type of conductivity. The thesis is devoted to the study of the processes of interaction between native and impurity defects in zinc selenide. It is established that the Au impurity has the most prominent amphoteric properties in ZnSe among Cu, Ag and Au impurities, as it forms a great number of both Au; donors and Auz„ acceptors. Electrical measurements show that Ag and Au ions introduced into vacant sites of the Zn sublattice form simple single-charged Agz„+ and Auzn+ states with d1° electron configuration, while Cu ions can form both single-charged Cuz„ (d1) and double-charged Cuzr`+ (d`o) centres. Amphoteric properties of Ag and Au transition metals stimulated by time are found for the first time from both electrical and luminescent measurements. A model that explains the changes in electrical and luminescent parameters by displacement of Ag ions into interstitial sites due to lattice deformation forces is proposed. Formation of an Ag;-donor impurity band in ZnSe samples doped with Ag and stored at room temperature is also studied. Thus, the properties of the doped samples are modified due to large lattice relaxation during aging. This fact should be taken into account in optoelectronic applications of doped ZnSe and related compounds.

The valence band alignment at ultrathin SiO2/Si interfaces

High resolution x-ray photoelectron spectroscopy has been used to determine the valence band alignment at ultrathin SiO2/Si interfaces. In the oxide thickness range 1.6-4.4 nm the constant band-offset values of 4.49 and 4.43 eV have been obtained for the dry SiO2/Si(100) and the wet SiO2/Si(100) interfaces, respectively. The valence band alignment of dry SiO2/Si(111) (4.36 eV) is slightly smaller than the case of the dry SiO2/Si(100) interface.

Innovative implementation by non-state actors in environment-related areas : towards a positive implementation gap ?

This contribution (presented in the first International Conference on Public Policy (ICPP) in Grenoble in June 2013) explores the phenomena of innovation in action ("innovative implementation"). To do so, we operationalize "innovative implementation" as a strategy by which (coalitions of) non-state actors seek to develop ad hoc solutions to address a given environmental issue, going beyond what is provided for in formal policy designs. Following an inductive research strategy, we elaborate a conceptual framework whose main advantage is to bring the actors and their coalition (in all their diversity) back in the analysis. More concretely, we state that perceiving implementation as broader 'social interaction processes' (De Boer & Bressers 2011) within which actors play strategic 'games' (Bardach 1977, Scharpf 1997) opens interesting lines of research to better account for their innovative and strategic behaviours. In a second step, we apply this framework to three strategies of innovative implementation in different contexts, and identify on this basis empirical regularities in the individual pathways related to the emergence and success (or failure) of these strategies.

Proximity of excitatory synapses and astroglial gap junctions in layer IV of the mouse barrel cortex.

Neurons and astrocytes, the two major cell populations in the adult brain, are characterized by their own mode of intercellular communication--the synapses and the gap junctions (GJ), respectively. In addition, there is increasing evidence for dynamic and metabolic neuroglial interactions resulting in the modulation of synaptic transmission at the so-called "tripartite synapse". Based on this, we have investigated at the ultrastructural level how excitatory synapses (ES) and astroglial GJ are spatially distributed in layer IV of the barrel cortex of the adult mouse. We used specific antibodies for connexin (Cx) 30 and 43 to identify astroglial GJ, these two proteins are known to be present in the majority of astroglial GJ in the cerebral cortex. In electron-microscopic images, we measured the distance between two ES, between two GJ and between a GJ and its nearest ES. We found a ratio of two GJ per three ES in the hollow and septal areas. Taking into account the size of an astrocyte domain, the high density of GJ suggests the occurrence of reflexive type, i.e. GJ between processes of the same astrocyte. Interestingly, the distance between an ES and an astroglial GJ was found to be significantly lower than that between either two synapses or between two GJ. These observations indicate that the two modes of cell-to-cell communication are not randomly distributed in layer IV of the barrel cortex. Consequently, this feature may provide the morphological support for the recently reported functional interactions between neuronal circuits and astroglial networks.

SAHAUSTEKNOLOGIA TEOLLISILLA SAHALAITOKSILLA NYT JA TULEVAISUUDESSA

Diplomityössä on selvitetty teollisen sahaustekniikan nykytilaa ja sahausprosessissa käytettävien sahakoneiden teknistä kehitystä Pohjois- ja Keski-Euroopassa. Sahakonevalmistajia on tutkittu niiden tuottamien laitteiden kautta sekä yleisen saatavilla olevan taloudellisen ja tieteellisten tutkimusten tarjoaman informaation avulla. Tutkimuksessa mukana oleviin sahakoneisiin tutustuminen suoritettiin sahalaitosvierailuilla suomalaisilla sahalaitoksilla kevään 2002 aikana. Tieteellisten julkaisujen tietoja verrattiin samalla vallitsevaan tilanteeseen sahoilla. Samalla tehtyjen haastatteluiden avulla selvitettiin sahakoneisiin liittyvien investointien vaikuttimia. Haastatteluiden kohteena olivat sahateollisuuden tuotannosta ja teknisestä suunnittelusta sekä johtamisesta vastaavia henkilöitä erikokoisista sahateollisuusyrityksistä. Myös muutamat sahakonevalmistajien edustajat antoivat haastattelun omia laitteitaan koskien. Sahaustuotannon raaka-ainetilannetta tutkittiin tutkimusalueella maakohtaisesti. Sahaustekniikkana nelisahaus on vallitseva työstömuoto. Siinä käytettävät sahakoneet ovat pelkkahakkuri, joka hakettaa tukin sivut sivutuotehakkeeksi, profilointiyksiköt, jotka työstävät tukin tai pelkan pintaan sivutavarakappaleiden leveyden ennen tai jälkeen pyörösahayksiköitä, jotka erottavat sahatavarakappaleet toisistaan. Merkittävimmät oheislaitteet ovat tukin ja pelkan mittauslaitteet sekä tukinsyöttölaitteet, joiden perusteella puun käytön optimointi sahausprosessissa ja suuntaus sahakoneisiin tapahtuu. Mittatarkimmat ja tuotantonopeudeltaan nopeimmat pyörösahayksiköt ovat kaksiakselisia, profiloivia sahakoneita. Näillä ominaisuuksilla on suurin painoarvo myös sahojen investointisuunnittelussa nopean käyntiinajon lisäksi. Sahakoneiden kehitykseen vaikuttavia seikkoja ovat tulevaisuudessa tukkien koon pieneneminen istutusmetsien jalostuksen lisääntyessä ja suurten aarniometsien vähetessä. Terätekniikan kehitys on tuottaa edelleen ohuempia teriä teräohjaimin, luomalla teriin sisäisiä jännityksiä tai kehittämällä uusia terägeometrioita.

Two-dimensional probabilistic inversion of plane-wave electromagnetic data: Methodology, model constraints and joint inversion with electrical resistivity data

Probabilistic inversion methods based on Markov chain Monte Carlo (MCMC) simulation are well suited to quantify parameter and model uncertainty of nonlinear inverse problems. Yet, application of such methods to CPU-intensive forward models can be a daunting task, particularly if the parameter space is high dimensional. Here, we present a 2-D pixel-based MCMC inversion of plane-wave electromagnetic (EM) data. Using synthetic data, we investigate how model parameter uncertainty depends on model structure constraints using different norms of the likelihood function and the model constraints, and study the added benefits of joint inversion of EM and electrical resistivity tomography (ERT) data. Our results demonstrate that model structure constraints are necessary to stabilize the MCMC inversion results of a highly discretized model. These constraints decrease model parameter uncertainty and facilitate model interpretation. A drawback is that these constraints may lead to posterior distributions that do not fully include the true underlying model, because some of its features exhibit a low sensitivity to the EM data, and hence are difficult to resolve. This problem can be partly mitigated if the plane-wave EM data is augmented with ERT observations. The hierarchical Bayesian inverse formulation introduced and used herein is able to successfully recover the probabilistic properties of the measurement data errors and a model regularization weight. Application of the proposed inversion methodology to field data from an aquifer demonstrates that the posterior mean model realization is very similar to that derived from a deterministic inversion with similar model constraints.

Compositional influence on the electrical performance of zinc indium tin oxide transparent thin-film transistors

In this work, zinc indium tin oxide layers with different compositions are used as the active layer of thin film transistors. This multicomponent transparent conductive oxide is gaining great interest due to its reduced content of the scarce indium element. Experimental data indicate that the incorporation of zinc promotes the creation of oxygen vacancies. In thin-film transistors this effect leads to a higher threshold voltage values. The field-effect mobility is also strongly degraded, probably due to coulomb scattering by ionized defects. A post deposition annealing in air reduces the density of oxygen vacancies and improves the fieldeffect mobility by orders of magnitude. Finally, the electrical characteristics of the fabricated thin-film transistors have been analyzed to estimate the density of states in the gap of the active layers. These measurements reveal a clear peak located at 0.3 eV from the conduction band edge that could be attributed to oxygen vacancies.