Stress analysis of ZrO2/SiO2 multilayers deposited on different substrates with different thickness periods

The effects of repeating thickness periods on stress are studied in ZrO2/SiO2 multilayers deposited by electron-beam evaporation on BK7 glass and fused-silica substrates. The results show that the residual stress is compressive and decreases with an increase of the periods of repeating thickness in the ZrO2/SiO2 multilayers. At the same time, the residual stress in multilayers deposited on BK7 glass is less than that of samples deposited on fused silica. The variation of the microstructure examined by x-ray diffraction shows that microscopic deformation does not correspond to macroscopic stress, which may be due to variation of the interface stress. (c) 2005 Optical Society of America.

Note sur les premiers essais de capture du crabe profond Geryon quinquedens en Côte d'Ivoire

First experiments to trap the deep sea red crab Geryon quinquedens off Côte d'Ivoire have had good success. The yields obtained are similar to those observed off the northeastern coast of the United States and off Angola, where commercial fisheries have been developed for some years.

Stress, absorptance and laser-induced damage threshold properties of 355-nm HR coatings

A number of 355-nm Al2O3/MgF2 high-reflectance (HR) coatings were prepared by electron-beam evaporation. The influences of the number of coating layers and deposition temperature on the 355-nm Al2O3/MgF2 HR coatings were investigated. The stress was measured by viewing the substrate deformation before and after coating deposition using an optical interferometer. The laser-induced damage threshold (LIDT) of the samples was measured by a 355-nm Nd:YAG laser with a pulse width of 8 ns. Transmittance and reflectance of the samples were measured by a Lambda 900 spectrometer. It was found that absorptance was the main reason to result in a low LIDT of 355-nm Al2O3/MgF2 HR coatings. The stress in Al2O3/MgF2 HR coatings played an unimportant role in the LIDT, although MgF2 is known to have high tensile stress.

Influences of annealing on residual stress and structure of HfO2 films

HfO2 Elms are deposited on BK7 glass substrates by electron beam evaporation. The influences of annealing between 100 degrees C and 400 degrees C on residual stresses and structures of HfO2 films are studied. It is found that little differences of spectra, residual stresses and structures are obtained after annealing at lower temperatures. After annealing at higher temperatures, the spectra shift to short wavelength, the residual stress increases with the increasing annealing temperature. At the same time, the crystallite size increases and interplanar distance decreases. The variations of optical spectra and residual stress correspond to the evolutions of structures induced by annealing.

Influence of ytterbia content on residual stress and microstructure of Y2O3-ZrO2 thin films prepared by EB-PVD

Y2O3 stabilized ZrO2 (YSZ) thin films with different Y2O3 molar contents (0, 3, 7, and 12 mol%) are deposited on BK7 substrates by electron-beam evaporation technique. The effects of different Y2O3 contents on residual stresses and structures of YSZ thin films are studied. Residual stresses are investigated by means of two different techniques: the curvature measurement and x- ray diffraction method. It is found that the evolution of residual stresses of YSZ thin films by the two different methods is consistent. Residual stresses of films transform from compressive stress into tensile stress and the tensile stress increases monotonically with the increase of Y2O3 content. At the same time, the structures of these films change from the mixture of amorphous and monoclinic phases into high temperature cubic phase. The variations of residual stress correspond to the evolution of structures induced by adding of Y2O3 content.

An assessment of the efficiency of three active fish capture methods and a study of roach / bream hybrids on the Crossens drainage system near Southport.

An assessment of three methods of fish capture, to establish the best fishing method which reflects the best range of sizes and species of fish in a given area. The methods used were trawl netting, electrofishing, and seine netting which were assessed on the Crossens drainage system near Southport. The report also includes a study of roach / bream hybrids that were found at the site, which focuses on their distinguishing features and compared with the features of roach and bream.

Effects of lunar cycle and fishing operations on longline-caught pelagic fish: fishing performance, capture time, and survival of fish

Commercial longline fishing data were analyzed and experiments were conducted with gear equipped with hook timers and timedepth recorders in the Réunion Island fishery (21°5ʹS lat., 53°28ʹE long.) to elucidate direct and indirect effects of the lunar cycle and other operational factors that affect catch rates, catch composition, fish behavior, capture time, and fish survival. Logbook data from 1998 through 2000, comprising 2009 sets, indicated that swordfish (Xiphias gladius) catch-per unit of effort (CPUE) increased during the first and last quarter of the lunar phase, whereas albacore (Thunnus alalunga) CPUE was highest during the full moon. Swordfish were caught rapidly after the longline was set and, like bigeye tuna (Thunnus obesus), they were caught during days characterized by a weak lunar illumination—mainly during low tide. We found a significant but very low influence of chemical lightsticks on CPUE and catch composition. At the time the longline was retrieved, six of the 11 species in the study had >40% survival. Hook timers indicated that only 8.4% of the swordfish were alive after 8 hours of capture, and two shark species (blue shark [Prionace glauca] and oceanic whitetip shark [Carcharhinus longimanus]) showed a greater resilience to capture: 29.3% and 23.5% were alive after 8 hours, respectively. Our results have implications for current fishing practices and we comment on the possibilities of modifying fishing strategies in order to reduce operational costs, bycatch, loss of target fish at sea, and detrimental impacts on the environment.

Evaluation of the capture efficiency and size selectivity of four pot types in the prospective fishery for North Pacific giant octopus (Enteroctopus dofleini)

Over 230 metric tons of octopus is harvested as bycatch annually in Alaskan trawl, long-line, and pot fisheries. An expanding market has fostered interest in the development of a directed fishery for North Pacific giant octopus (Enteroctopus dofleini). To investigate the potential for fishery development we examined the efficacy of four different pot types for capture of this species. During two surveys in Kachemak Bay, Alaska, strings of 16 –20 sablefish, Korean hair crab, shrimp, and Kodiak wooden lair pots were set at depths ranging between 62 and 390 meters. Catch per-unit-of-ef for t estimates were highest for sablefish and lair pots. Sablefish pots caught significantly heavier North Pacific giant octopuses but also produced the highest bycatch of commercially important species, such as halibut (Hippoglossus stenolepis), Pacific cod (Gadus macrocephalus), and Tanner crab (Chionoecetes bairdi).