In situ SANS study of the surface and pore filling adsorption of subcritical and supercritical CO2 in porous silica as a function of pore size

We applied small-angle neutron scattering (SANS) and ultra small-angle neutron scattering (USANS) to monitor evolution of the CO2 adsorption in porous silica as a function of CO2 pressure and temperature in pores of different sizes. The range of pressures (0 < P < 345 bar) and temperatures (T=18 OC, 35 OC and 60 OC) corresponded to subcritical, near critical and supercritical conditions of bulk fluid. We observed that the adsorption behavior of CO2 is fundamentally different in large and small pores with the sizes D > 100 Å and D < 30 Å, respectively. Scattering data from large pores indicate formation of a dense adsorbed film of CO2 on pore walls with the liquid-like density (ρCO2)ads≈0.8 g/cm3. The adsorbed film coexists with unadsorbed fluid in the inner pore volume. The density of unadsorbed fluid in large pores is temperature and pressure dependent: it is initially lower than (ρCO2)ads and gradually approaches it with pressure. In small pores compressed CO2 gas completely fills the pore volume. At the lowest pressures of the order of 10 bar and T=18 OC, the fluid density in smallest pores available in the matrix with D ~ 10 Å exceeds bulk fluid density by a factor of ~ 8. As pressure increases, progressively larger pores become filled with the condensed CO2. Fluid densification is only observed in pores with sizes less than ~ 25 – 30 Å. As the density of the invading fluid reaches (ρCO2)bulk~ 0.8 g/cm3, pores of all sizes become uniformly filled with CO2 and the confinement effects disappear. At higher densities the fluid in small pores appears to follow the equation of state of bulk CO2 although there is an indication that the fluid density in the inner volume of large pores may exceed the density of the adsorbed layer. The equivalent internal pressure (Pint) in the smallest pores exceeds the external pressure (Pext) by a factor of ~ 5 for both sub- and supercritical CO2. Pint gradually approaches Pext as D → 25 – 30 Å and is independent of temperature in the studied range of 18 OC ≤ T ≤ 60 OC. The obtained results demonstrate certain similarity as well as differences between adsorption of subcritical and supercritical CO2 in disordered porous silica. High pressure small angle scattering experiments open new opportunities for in situ studies of the fluid adsorption in porous media of interest to CO2 sequestration, energy storage, and heterogeneous catalysis.

Submission to House Standing Committee on Infrastructure and Communications inquiry into IT Pricing

The strategies of price discrimination engaged in by a number of international publishers, coupled with a lack of competition and restrictions on the ability of consumers to engage in arbitrage, is likely to undermine the legitimacy of copyright law in Australia. By increasing prices beyond a reasonable and fair level, these strategies also undermine the goal of copyright law to enhance access to cultural goods. Enhancing access – and therefore lowering prices – is crucial to enhancing Australia's innovative capacity and the ability of Australians to experience, learn, act, and grow through cultural works. We recommend that the committee investigates the following options: 1. Repeal parallel importation restrictions; 2. Fundamentally reconsider the operation of anti-circumvention law in the context of digital distribution models; 3. Prohibit and render unenforceable contractual restrictions on parallel importation; 4. Introduce a right of digital resale in Australia.

Changes in profit as market conditions change : an historical study of a building firm

This paper analyses the profits from 221 construction projects undertaken by an Australian building firm in the period 1910–1938 and examines the factors that influence the firm's profit levels. This involves a series of multiple regression analyses with three dependent variables representing profit and 26 independent variables representing economic conditions and project characteristics. From these, 11 models are derived of which two are chosen as having the best explanatory power in explaining approximately 72% of the variability in profit levels movements. The results show that unemployment, interest rates, level of construction activity in the state, change of wage level, inflation rate of building material and project value significantly influenced the firm's profit level during the period.

Pricing approaches in the construction industry

Contractors have to bid competitively for most of their work and at the same time deal with the risks and uncertainties connected with bid submission. This article examines the factors involved in tender pricing and how they interrelate. From this, a conceptual model of contractors’ pricing strategy is developed.

UCPR r243 - notice of non-party disclosure - obligation to state allegation to which documents sought are directly relevant

In Deppro Pty Ltd v Hannah [2008] QSC 193 one of the matters considered by the court related to the requirement in r 243 of the Uniform Civil Procedure Rules 1999 (Qld) that a notice of non-party disclosure must “state the allegation in issue in the pleadings about which the document sought is directly relevant.”The approach adopted by the issuing party in this case of asserting that documents sought by a notice of non-party disclosure are relevant to allegations in numbered paragraphs in pleadings, and serving copies of the pleadings with the notice, is not uncommon in practice. This decision makes it clear that this practice is fraught with danger. In circumstances where it is not apparent that the non-party has been fully apprised of the relevant issues the decision suggests an applicant for non-party disclosure who has not complied with the requirements of s 243 might be required to issue a fresh, fully compliant notice, and to suffer associated costs consequences.

Hybrid graphene/titania nanocomposite : interface charge transfer, hole doping, and sensitization for visible light response

We demonstrated for the first time by large-scale ab initio calculations that a graphene/titania interface in the ground electronic state forms a charge-transfer complex due to the large difference of work functions between graphene and titania, leading to substantial hole doping in graphene. Interestingly, electrons in the upper valence band can be directly excited from graphene to the conduction band, that is, the 3d orbitals of titania, under visible light irradiation. This should yield well-separated electron−hole pairs, with potentially high photocatalytic or photovoltaic performance in hybrid graphene and titania nanocomposites. Experimental wavelength-dependent photocurrent generation of the graphene/titania photoanode demonstrated noticeable visible light response and evidently verified our ab initio prediction.

State of multilevel research perspective in the information systems discipline

Existing distinctions among macro and micro approaches have been jeopardising the advances of Information Systems (IS) research. Both approaches have been criticized for explaining one level while neglecting the other; thereby, the current situation necessitates the application of multilevel research for revealing the deficiencies. Instead of studying single level (macro or micro), multilevel research entails more than one level of conceptualization and analysis, simultaneously. As the notion of multilevel is borrowed from reference disciplines, there tends to be confusions and inconsistencies within the IS discipline, which hinders the adoption of multilevel research. This paper speaks for the potential value of multilevel research, by investigating the current application status of multilevel research within the IS domain. A content analysis of multilevel research articles from major IS conferences and journals is presented. Analysis results suggest that IS scholars have applied multilevel research to produce high quality work ranging from a variety of topics. However, researchers have not yet been consistently defining “multilevel”, leading to idiosyncratic meanings of multilevel research, most often, in authors’ own interpretations. We argue that a rigorous definition of “multilevel research” needs to be explicated for consistencies in research community.

Factors influencing funding decisions by elected politicians at the state/provincial level : a case study of public libraries in Canada

The purpose of this study was to determine factors (internal and external) that influenced Canadian provincial (state) politicians when making funding decisions about public libraries. Using the case study methodology, Canadian provincial/state level funding for public libraries in the 2009-10 fiscal year was examined. After reviewing funding levels across the country, three jurisdictions were chosen for the case: British Columbia's budget revealed dramatically decreased funding, Alberta's budget showed dramatically increased funding, and Ontario's budget was unchanged from the previous year. The primary source of data for the case was a series of semi-structured interviews with elected officials and senior bureaucrats from the three jurisdictions. An examination of primary and secondary documents was also undertaken to help set the political and economic context as well as to provide triangulation for the case interviews. The data were analysed to determine whether Cialdini's theory of influence (2001) and specifically any of the six tactics of influence (i.e, commitment and consistency, authority, liking, social proof, scarcity and reciprocity) were instrumental in these budget processes. Findings show the principles of "authority", "consistency and commitment" and "liking" were relevant, and that "liking" were especially important to these decisions. When these decision makers were considering funding for public libraries, they most often used three distinct lenses: the consistency lens (what are my values? what would my party do?), the authority lens (is someone with hierarchical power telling me to do this? are the requests legitimate?), and most importantly, the liking lens (how much do I like and know about the requester?). These findings are consistent with Cialdini's theory, which suggests the quality of some relationships is one of six factors that can most influence a decision maker. The small number of prior research studies exploring the reasons for increases or decreases in public library funding allocation decisions have given little insight into the factors that motivate those politicians involved in the process and the variables that contribute to these decisions. No prior studies have examined the construct of influence in decision making about funding for Canadian public libraries at any level of government. Additionally, no prior studies have examined the construct of influence in decision making within the context of Canadian provincial politics. While many public libraries are facing difficult decisions in the face of uncertain funding futures, the ability of the sector to obtain favourable responses to requests for increases may require a less simplistic approach than previously thought. The ability to create meaningful connections with individuals in many communities and across all levels of government should be emphasised as a key factor in influencing funding decisions.

Labor market reform and the changing structure of wage determination in China's state sector during the 1980s

China's market-oriented labor market reform has been in place for about one and a half decades. This study uses individual data for 1981 and 1987 to examine the success of the first half of the reform program. Success is evaluated by examining changes in the wage setting structure in the state-owned sector over the reform period. Have the market reforms stimulated worker incentives by increasing the returns to human capital acquisition? Has the wage structure altered to more closely mimic that of a market economy? In 1987, there is evidence of a structural change in the system of wage determination, with slightly increased rates of return to human capital. However, changes in industrial wage differentials appear to play the dominant role. It is argued that this may be due to labor market reforms, in particular the introduction of the profit related bonus scheme.J. Comp. Econom.,December 1997,25(3), pp. 403–421. Australian National University, Canberra, ACT0200, Australia and University of Tasmania, Hobart, Tasmania, Australia, and University of Aberdeen, Old Aberdeen, Scotland AB24 3QY.

Bearing fault prognosis based on health state probability estimation

In condition-based maintenance (CBM), effective diagnostic and prognostic tools are essential for maintenance engineers to identify imminent fault and predict the remaining useful life before the components finally fail. This enables remedial actions to be taken in advance and reschedule of production if necessary. All machine components are subjected to degradation processes in real environments and they have certain failure characteristics which can be related to the operating conditions. This paper describes a technique for accurate assessment of the remnant life of bearings based on health state probability estimation and historical knowledge embedded in the closed loop diagnostics and prognostics system. The technique uses the Support Vector Machine (SVM) classifier as a tool for estimating health state probability of machine degradation process to provide long term prediction. To validate the feasibility of the proposed model, real life fault historical data from bearings of High Pressure-Liquefied Natural Gas (HP-LNG) pumps were analysed and used to obtain the optimal prediction of remaining useful life (RUL). The results obtained were very encouraging and showed that the proposed prognosis system based on health state probability estimation has the potential to be used as an estimation tool for remnant life prediction in industrial machinery.

Mathematical modelling of controlled drug release from polymer micro-spheres : incorporating the effects of swelling, diffusion and dissolution via moving boundary problems

Controlled drug delivery is a key topic in modern pharmacotherapy, where controlled drug delivery devices are required to prolong the period of release, maintain a constant release rate, or release the drug with a predetermined release profile. In the pharmaceutical industry, the development process of a controlled drug delivery device may be facilitated enormously by the mathematical modelling of drug release mechanisms, directly decreasing the number of necessary experiments. Such mathematical modelling is difficult because several mechanisms are involved during the drug release process. The main drug release mechanisms of a controlled release device are based on the device’s physiochemical properties, and include diffusion, swelling and erosion. In this thesis, four controlled drug delivery models are investigated. These four models selectively involve the solvent penetration into the polymeric device, the swelling of the polymer, the polymer erosion and the drug diffusion out of the device but all share two common key features. The first is that the solvent penetration into the polymer causes the transition of the polymer from a glassy state into a rubbery state. The interface between the two states of the polymer is modelled as a moving boundary and the speed of this interface is governed by a kinetic law. The second feature is that drug diffusion only happens in the rubbery region of the polymer, with a nonlinear diffusion coefficient which is dependent on the concentration of solvent. These models are analysed by using both formal asymptotics and numerical computation, where front-fixing methods and the method of lines with finite difference approximations are used to solve these models numerically. This numerical scheme is conservative, accurate and easily implemented to the moving boundary problems and is thoroughly explained in Section 3.2. From the small time asymptotic analysis in Sections 5.3.1, 6.3.1 and 7.2.1, these models exhibit the non-Fickian behaviour referred to as Case II diffusion, and an initial constant rate of drug release which is appealing to the pharmaceutical industry because this indicates zeroorder release. The numerical results of the models qualitatively confirms the experimental behaviour identified in the literature. The knowledge obtained from investigating these models can help to develop more complex multi-layered drug delivery devices in order to achieve sophisticated drug release profiles. A multi-layer matrix tablet, which consists of a number of polymer layers designed to provide sustainable and constant drug release or bimodal drug release, is also discussed in this research. The moving boundary problem describing the solvent penetration into the polymer also arises in melting and freezing problems which have been modelled as the classical onephase Stefan problem. The classical one-phase Stefan problem has unrealistic singularities existed in the problem at the complete melting time. Hence we investigate the effect of including the kinetic undercooling to the melting problem and this problem is called the one-phase Stefan problem with kinetic undercooling. Interestingly we discover the unrealistic singularities existed in the classical one-phase Stefan problem at the complete melting time are regularised and also find out the small time behaviour of the one-phase Stefan problem with kinetic undercooling is different to the classical one-phase Stefan problem from the small time asymptotic analysis in Section 3.3. In the case of melting very small particles, it is known that surface tension effects are important. The effect of including the surface tension to the melting problem for nanoparticles (no kinetic undercooling) has been investigated in the past, however the one-phase Stefan problem with surface tension exhibits finite-time blow-up. Therefore we investigate the effect of including both the surface tension and kinetic undercooling to the melting problem for nanoparticles and find out the the solution continues to exist until complete melting. The investigation of including kinetic undercooling and surface tension to the melting problems reveals more insight into the regularisations of unphysical singularities in the classical one-phase Stefan problem. This investigation gives a better understanding of melting a particle, and contributes to the current body of knowledge related to melting and freezing due to heat conduction.

Comment on "Local accumulation times for source, diffusion, and degradation models in two and three dimensions" [J. Chem. Phys. 138, 104121 (2013)]

In a recent paper, Gordon, Muratov, and Shvartsman studied a partial differential equation (PDE) model describing radially symmetric diffusion and degradation in two and three dimensions. They paid particular attention to the local accumulation time (LAT), also known in the literature as the mean action time, which is a spatially dependent timescale that can be used to provide an estimate of the time required for the transient solution to effectively reach steady state. They presented exact results for three-dimensional applications and gave approximate results for the two-dimensional analogue. Here we make two generalizations of Gordon, Muratov, and Shvartsman’s work: (i) we present an exact expression for the LAT in any dimension and (ii) we present an exact expression for the variance of the distribution. The variance provides useful information regarding the spread about the mean that is not captured by the LAT. We conclude by describing further extensions of the model that were not considered by Gordon,Muratov, and Shvartsman. We have found that exact expressions for the LAT can also be derived for these important extensions...

Blocking layer optimisation of poly(3-hexylthiopene)based solid state dye sensitized solar cells

The optimisation study of the fabrication of a compact TiO2 blocking layer (via Spray Pyrolysis Deposition) for poly (3-hexylthiopene) (P3HT) for Solid State Dye Sensitized Solar Cells (SDSCs) is reported. We used a novel spray TiO2 precursor solution composition obtained by adding acetylacetone to a conventional formulation (Diisopropoxytitanium bis (acetylacetonate) in ethanol). By Scanning Electron Microscopy a TiO2 layer with compact morphology and thickness of around 100 nmis shown. Through a Tafel plot analysis an enhancement of the device diode-like behaviour induced by the acetylacetone blocking layer respect to the conventional one is observed. Significantly, the device fabricatedwith the acetylacetone blocking layer shows an overall increment of the cell performance with respect to the cellwith the conventional one (DJsc/Jsc = +13.8%, DFF/FF = +39.7%, DPCE/PCE = +55.6%). A conversion efficiency optimumis found for 15 successive spray cycles where the diode-like behaviour of the acetylacetone blocking layer is more effective. Over three batches of cells (fabricated with P3HT and dye D35) an average conversion efficiency value of 3.9% (under a class A sun simulator with 1 sun A.M. 1.5 illumination conditions) was measured. From the best cell we fabricated a conversion efficiency value of 4.5% was extracted. This represents a significant increment with respect to previously reported values for P3HT/dye D35 based SDSCs.

Political networks on twitter : tweeting the Queensland state election

This paper examines patterns of political activity and campaigning on Twitter in the context of the 2012 election in the Australian state of Queensland. Social media have been a visible component of political campaigning in Australia at least since the 2007 federal election, with Twitter, in particular, rising to greater prominence in the 2010 federal election. At state level, however, they have remained comparatively less important thus far. In this paper, we track uses of Twitter in the Queensland campaign from its unofficial start in February through to the election day of 24 March 2012. We both examine the overall patterns of activity in the hash tag #qldvotes, and track specific interactions between politicians and other users by following some 80 Twitter accounts of sitting members of parliament and alternative candidates. Such analysis provides new insights into the different approaches to social media campaigning which were embraced by specific candidates and party organisations, as well as an indication of the relative importance of social media activities, at present, for state-level election campaigns.

Final-state effects in neutron Compton scattering measurements on zirconium deuteride and beryllium

We report inelastic neutron scattering measurements of the neutron Compton profile, J(y), for Be and for D in polycrystalline ZrD2 over a range of momentum transfers, q between 27 and 178 °A−1. The measurements were performed using the inverse geometry spectrometer eVS which is situated at the UK pulsed spallation neutron source ISIS. We have investigated deviations from impulse approximation (IA) scattering which are generically referred to as final state effects (FSEs) using a method described by Sears. This method allows both the magnitude and the q dependence of the FSE to be studied. Analysis of the measured data was compared with analysis of numerical simulations based on the harmonic approximation and good agreement was found for both ZrD2 and Be. Finally we have shown how (∇2V), where V is the interatomic potential, can be extracted from the antisymmetric component of J(y).