FWPRDC PN06.3016 Resource Characterisation

Linking non-destructive field assessment of wood property and quality traits in slash pine to yield of structural grades of timber. Produce a review of wood quality studies in sub-tropical pines planted in Queensland and northern New South Wales.

Small Log Processing Resource Specification

Sawing studies of mixed species and age plantation hardwoods representing potential early resource flows available to plantation sawlog processing industry. Provide information needed to underpin a business case to invest in small log sawing infrastucture.

Chemical probes into the active centre of a heme thiolate monoxygenase

Linalool-8-monoxygenase, a typical bacterial P-450 heme thiolase, shows a high degree of substrate specificity towards linalool. The active site of the pure enzyme has been probed with a large number of substrate analogues with systematic alterations or conformational variations in the linalool molecule. The comparison of three parameters, the mo→mos conversion of the enzyme as a result of substrate binding monitored at 392 nm, theK D of the analogues giving information about energies of association and the relative turnover as substrate have given information about the space-filling characteristics of the substrates in the enzyme cleft, the number of contacts the molecules make with the respective domains of the enzyme and the distance of the site undergoing hydroxylation from the oxygen site, respectively. The data permit the conclusion that linalool makes contact with the enzyme by hydrogen bonding with the hydroxyl group as well through hydrophobic association with all the eight carbons carrying hydrogen in the molecules.

K-Ar ages of biotite and muscovite from Pangong metamorphic complex, Shyok suture zone, India: Implications for the youngest post-collision metamorphic event in Ladakh Himalaya

The garnet-kyanite-staurolite and garnet-biotite-staurolite gneisses were collected from a locality within Lukung area that belongs to the Pangong metamorphic complex in Shyok valley, Ladakh Himalaya. The kyanite-free samples have garnet and staurolite in equilibrium, where garnets show euhedral texture and have flat compositional profile. On the other hand, the kyanite-bearing sample shows equilibrium assemblage of garnet-kyanite-staurolite along with muscovite and biotite. In this case, garnet has an inclusion rich core with a distinct grain boundary, which was later overgrown by inclusion free euhedral garnet. Garnet cores are rich in Mn and Ca, while the rims are poor in Mn and rich in Fe and Mg, suggesting two distinct generations of growth. However, the compositional profiles and textural signature of garnets suggests the same stage of P -T evolution for the formation of the inclusion free euhedral garnets in the kyanite-free gneisses and the inclusion free euhedral garnet rims in the kyanite-bearing gneiss. Muscovites from the four samples have consistent K-Ar ages, suggesting the cooling age (∼ 10 Ma) of the gneisses. These ages make a constraint on the timing of the youngest post-collision metamorphic event that may be closely related to an activation of the Karakoram fault in Pangong metamorphic complex.

Australian Tropical Grains Germplasm Centre

DAQ00131 project activities aimed to: conserve tropical grains germplasm under long-term storage conditions; acquire new germplasm with unique traits of interest to clients (particularly to breeding programs); the maintenance of germplasm through viability testing and regeneration; and to increase awareness of the availability of tropical grains germplasm to clients. New project goals were to facilitate the creation of the national grains Genetic Resources Centre (GRC) and included training GRC staff in the use of GRIN-Global (GG), a software management system, so that grains data can be nationalised across Australia; and contribute to the action plan development for the relocation of tropical grains germplasm to both Tamworth and Horsham.

AG15 (Sustainable Agricultural State-level Investment Program) natural resource management extension in irrigated cotton and grain

Natural Resource Management project developing reources and supporting best practice management for irrigated cotton and grain growers in Queensland.

BSDD-2.0: Biomolecules Segment Display Device - An updated web accessible computing resource

The existing internet computing resource, Biomolecules Segment Display Device (BSDD), has been updated with several additional useful features. An advanced option is provided to superpose the structural motifs obtained from a search on the Protein Data Bank (PDB) in order to see if the three-dimensional structures adopted by identical or similar sequence motifs are the same. Furthermore, the options to display structural aspects like inter- and intra-molecular interactions, ion-pairs, disulphide bonds, etc. have been provided.The updated resource is interfaced with an up-to-date copy of the public domain PDB as well as 25 and 90% non-redundant protein structures. Further, users can upload the three-dimensional atomic coordinates (PDB format) from the client machine. A free molecular graphics program, JMol, is interfaced with it to display the three-dimensional structures.

Community forestry and environmental literacy in northern Thailand : Towards collaborative natural resource management and conservation

Conservation and sustainable management of tropical forests needs a holistic approach: in addition to ecological concerns, socio-economic issues including cultural aspects must be taken into consideration. An ability to adapt practices is a key to successful collaborative natural resource management. Achieving this requires local participation and understanding of local conceptions of the environment. This study examined these issues in the context of northern Thailand. Northern uplands are the home of much of the remaining natural forest in Thailand and several ethnic minority groups commonly referred to as hill tribes. The overall purpose of this study was to grasp a regional view of an ethnically diverse forested area and to elicit prospects to develop community forestry for conservation purposes and for securing people s livelihood. Conservation was a central goal of management as the forests in the area were largely designated as protected. The aim was to study local perceptions, objectives, values and practices of forest management, under the umbrella of the concept environmental literacy, as well as the effects of forest policy on community management goals and activities. Environmental literacy refers to holistic understanding of the environment. It was used as a tool to examine people s views, interests, knowledge and motivation associated to forests. The material for this study was gathered in six villages in Chiang Mai Province. Three minority groups were included in the study, the Karen, Hmong and Lawa, and also the Thai. Household and focus group interviews were conducted in the villages. In addition, officials at district, regional and national levels, workers of non-governmental organisations, and academics were interviewed, and some data were gathered from the students of a local school. The results showed that motivation for protecting the forests existed among each ethnic group studied. This was a result of culture and traditions evolved in the forest environment but also of a need to adapt to a changed situation and environment and to outside pressures. The consequences of deforestation were widely agreed on in the villages, and the impact of socio-economic changes on the forests and livelihood was also recognised. The forest was regarded as a source of livelihood providing land, products and services essential to the people inhabiting rural uplands. Traditions, fire control, cooperation, reforestation, separation of protected and utilisable areas, and rules were viewed as central for conservation. For the villagers, however, conservation meant sustainable use, whereas the government has tended to prefer strict restrictions on forest resource use. Thus, conflicts had arisen. Between communities, cooperation was more dominant than conflict. The results indicated that the heterogeneity of forest dwellers, although it has to be recognised, should not be overemphasised: ethnic diversity can be considered as no major obstacle for successful community forestry. Collaborative management is particularly important in protected areas in order to meet the conservation goals while providing opportunities for livelihood. Forest management needs more positive incentives and increased dialogue.

Management of multi-scale forest resource data over time

During the last decades there has been a global shift in forest management from a focus solely on timber management to ecosystem management that endorses all aspects of forest functions: ecological, economic and social. This has resulted in a shift in paradigm from sustained yield to sustained diversity of values, goods and benefits obtained at the same time, introducing new temporal and spatial scales into forest resource management. The purpose of the present dissertation was to develop methods that would enable spatial and temporal scales to be introduced into the storage, processing, access and utilization of forest resource data. The methods developed are based on a conceptual view of a forest as a hierarchically nested collection of objects that can have a dynamically changing set of attributes. The temporal aspect of the methods consists of lifetime management for the objects and their attributes and of a temporal succession linking the objects together. Development of the forest resource data processing method concentrated on the extensibility and configurability of the data content and model calculations, allowing for a diverse set of processing operations to be executed using the same framework. The contribution of this dissertation to the utilisation of multi-scale forest resource data lies in the development of a reference data generation method to support forest inventory methods in approaching single-tree resolution.

Resource characterisation of slash pine plantation wood quality.

This review highlights the considerable variation found in wood properties impacting timber stiffness and stability such as wood density, spiral grain and microfibril angle. Variation with age, site quality and environment, as well as amongst species, hybrids and genetic stock is reported and opportunities for product-focused wood quality improvement are identified.

Rotary veneering of plantation-grown spotted gum (Corymbia citriodora subsp. variegata) and Dunn's white gum (Eucalyptus dunnii)

This report evaluates the wood and veneer properties of plantation-grown spotted gum (Corymbia citriodora subsp. variegata, or CCV) and Dunn's white gum (Eucalyptus dunnii), grown at different stockings, in thinning trials near Ellangowan in north-east New South Wales (mean annual rainfall 1050 mm) and Kingaroy in south-east Queensland (mean annual rainfall 873 mm). Thinning trials were established at age seven years. Both species showed a significant increase in stem diameter growth of the dominant trees in response to thinning. At age 10 years, trees from the unthinned (950–1270 stems ha-1) and 300 stems ha-1 treatments were selected for veneering. Five dominant trees were felled from each combination of species x sites x thinning treatment. Diameter at breast height over bark of the selected trees ranged from 20 cm to 27 cm at Ellangowan, and 19 cm to 26 cm at Kingaroy. From each tree, 1.5 m long billets were removed at two positions: a butt billet from 0.3–1.8 m above ground and a top billet from approximately 5.5–7.0 m. Log end splitting was assessed 24 hours after harvesting and again after steaming, approximately four days after harvesting. Disks from just above both billets were collected for assessment of wood properties. Billets were peeled on a spindleless veneer lathe to produce a full veneer ribbon with a target green thickness of 2.8 to 3.0 mm. The 1.55 m wide (tangential dimension) veneer sheets were dried and graded according to AS/NZ Standard 2269:2008, which describes four veneer grades. Veneer samples taken along the length of the veneer ribbon, at regular intervals of 1.55 m, were tested for stiffness, shrinkage and density. Veneer length measurements were used to calculate the radial distance of each sample from the central axis of the billet. Overall veneer gross recoveries ranged from 50% to 70%. They were significantly lower at the Kingaroy site, for both species. The veneer recoveries achieved were 2–3 times higher than typical green off saw recoveries from small plantation hardwood logs of similar diameter. Most of the veneer recovered was classified as D-grade. CCV trees from the Ellangowan site yielded up to 38% of the better C-grade and higher grade veneers. The main limiting factors that prevented veneer from meeting higher grades were the presence of kino defects and encased knots. Splits in E. dunnii veneer also contributed to reduced grade quality. Log end splits were higher for E. dunnii than for CCV, and logs from Ellangowan exhibited more severe splitting. Split index was generally higher for top than for butt billets. Split index was strongly correlated with the average veneer grade from corresponding billets. The Ellangowan site, where rainfall was higher and trees grew faster, yielded significantly denser and stiffer veneers than did the drier sites near Kingaroy, where tree growth was slower. The difference was more pronounced for E. dunnii than for CCV. Differences in measured wood properties between thinned and unthinned treatments were generally small and not significant. On average, 10% of billet volume was lost during the peeling rounding-up process. Much of the wood laid down following thinning was removed during rounding-up, meaning the effect of thinning on veneer properties could not be effectively assessed. CCV was confirmed as having high veneer density and very good veneer stiffness, exceeding 15 GPa, making it very suitable for structural products. E. dunnii also demonstrated good potential as a useful structural plywood resource, achieving stiffness above 10 GPa. Veneer stiffness and density in CCV increased from pith to bark at both sites, while for E. dunnii there was a radial increase in these properties at the Ellangowan site only. At the drier Kingaroy site, veneer stiffness and density declined from mid-radius to the log periphery. This may be associated with prolonged drought from 2005 to 2009, corresponding to the later years of tree growth at the Kingaroy site. CCV appeared to be less sensitive to drought conditions. Standing tree acoustic velocity, determined by the Fakopp time-of-flight method, provided a reliable prediction of average veneer stiffness for both species (R2=0.78 for CCV and R2=0.90 for E. dunnii) suggesting that the Fakopp method may be a useful indicator of tree and stand quality, in terms of veneer stiffness in standing trees.

Host Records of Fruit Flies in the South Pacific

Understanding the host range for all of the fruit fly species within the South Pacific region is vital to establishing trade and quarantine protocols. This is important for the countries within the region and their trade partners. A significant aspect of the Australian Centre for International Agricultural Research (ACIAR) and Regional Fruit Fly Projects (RFFP) has been host fruit collecting which has provided information on fruit fly host records in the seven participating countries. This work is still continuing in all project countries at different intensities. In the Cook Islands, Fiji, Tonga and Western Samoa, fruit surveys have assumed a quarantine surveillance role, with a focus on high risk fruits, such as guava, mango, citrus, bananas, cucurbits and solanaceous fruits. In the Solomon Islands, Vanuatu and the Federated States of Micronesia (FSM), fruit surveys are still at the stage where host ranges are far from complete. By the end of the current project a more complete picture of the fruit fly hosts in these countries will have been gained. A brief summary of the data collected to date is as follows: 23 947 fruit samples collected to date; 2181 positive host fruit records; 31 fruit fly species reared from fruit; 12 species reared from commercial fruit. A commercial fruit is classed as an edible fruit with potential for trade at either a local or international level. This allows for the inclusion of endemic fruit species that have cultural significance as a food source. On the basis of these results, there are fruit fly species of major economic importance in the South Pacific region. However, considerably more fruit survey work is required in order to establish a detailed understanding of all the pest species.

Theoretical gain optimization studies in CO2-N2 lasers. III. Inclusion of line shape effects

The influence of Lorentz and Doppler line-broadening mechanisms on the small-signal optical gain of lasers and, in particular, gasdynamic lasers, is discussed. A relationship between the critical parameter reflecting the line-broadening mechanisms and some of the important parameters arising out of the gain optimization studies in CO2-N2 gasdynamic lasers is established. Using this relationship, methods by which the deleterious effect of the Doppler mechanisms on small-signal gain can be suppressed are suggested. Journal of Applied Physics is copyrighted by The American Institute of Physics.

Tropical dryland agroforestry on clay soils: : Analysis of systems based on Acacia senegal in the Blue Nile region, Sudan

Acacia senegal, the gum arabic producing tree, is the most important component in traditional dryland agroforestry systems in the Blue Nile region, Sudan. The aim of the present study was to provide new knowledge on the potential use of A. senegal in dryland agroforestry systems on clay soils, as well as information on tree/crop interaction, and on silvicultural and management tools, with consideration on system productivity, nutrient cycling and sustainability. Moreover, the aim was also to clarify the intra-specific variation in the performance of A. senegal and, specifically, the adaptation of trees of different origin to the clay soils of the Blue Nile region. In agroforestry systems established at the beginning of the study, tree and crop growth, water use, gum and crop yields, nutrient cycling and system performance were investigated for a period of four years (1999 to 2002). Trees were grown at 5 x 5 m and 10 x 10 m spacing alone or in mixture with sorghum or sesame; crops were also grown in sole culture. The symbiotic biological N2 fixation by A. senegal was estimated using the 15N natural abundance (δ15N) procedure in eight provenances collected from different environments and soil types of the gum arabic belt and grown in clay soil in the Blue Nile region. Balanites aegyptiaca (a non-legume) was used as a non-N-fixing reference tree species, so as to allow 15N-based estimates of the proportion of the nitrogen in trees derived from the atmosphere. In the planted acacia trees, measurements were made on shoot growth, water-use efficiency (as assessed by the δ13C method) and (starting from the third year) gum production. Carbon isotope ratios were obtained from the leaves and branch wood samples. The agroforestry system design caused no statistically significant variation in water use, but the variation was highly significant between years, and the highest water use occurred in the years with high rainfall. No statistically significant differences were found in sorghum or sesame yields when intercropping and sole crop systems were compared (yield averages were 1.54 and 1.54 ha-1 for sorghum and 0.36 and 0.42 t ha-1 for sesame in the intercropped and mono-crop plots, respectively). Thus, at an early stage of agroforestry system management, A. senegal had no detrimental effect on crop yield, but the pattern of resource capture by trees and crops may change as the system matures. Intercropping resulted in taller trees and larger basal and crown diameters as compared to the development of sole trees. It also resulted in a higher land equivalent ratio. When gum yields were analysed it was found that a significant positive relationship existed between the second gum picking and the total gum yield. The second gum picking seems to be a decisive factor in gum production and could be used as an indicator for the total gum yield in a particular year. In trees, the concentrations of N and P were higher in leaves and roots, whereas the levels of K were higher in stems, branches and roots. Soil organic matter, N, P and K contents were highest in the upper soil stratum. There was some indication that the P content slightly increased in the topsoil as the agroforestry plantations aged. At a stocking of 400 trees ha-1 (5 x 5 m spacing), A. senegal accumulated in the biomass a total of 18, 1.21, 7.8 and 972 kg ha-1of N, P, K and OC, respectively. Trees contributed ca. 217 and 1500 kg ha-1 of K and OC, respectively, to the top 25-cm of soil over the first four years of intercropping. Acacia provenances of clay plain origin showed considerable variation in seed weight. They also had the lowest average seed weight as compared to the sandy soil (western) provenances. At the experimental site in the clay soil region, the clay provenances were distinctly superior to the sand provenances in all traits studied but especially in basal diameter and crown width, thus reflecting their adaptation to the environment. Values of δ13C, indicating water use efficiency, were higher in the sand soil group as compared to the clay one, both in leaves and in branch wood. This suggests that the sand provenances (with an average value of -28.07 ) displayed conservative water use and high drought tolerance. Of the clay provenances, the local one (Bout) displayed a highly negative (-29.31 ) value, which indicates less conservative water use that resulted in high productivity at this particular clay-soil site. Water use thus appeared to correspond to the environmental conditions prevailing at the original locations for these provenances. Results suggest that A. senegal provenances from the clay part of the gum belt are adapted for a faster growth rate and higher biomass and gum productivity as compared to provenances from sand regions. A strong negative relationship was found between the per-tree gum yield and water use efficiency, as indicated by δ13C. The differences in water use and gum production were greater among provenance groups than within them, suggesting that selection among rather than within provenances would result in distinct genetic gain in gum yield. The relative δ15N values ( ) were higher in B. aegyptiaca than in the N2-fixing acacia provenances. The amount of Ndfa increased significantly with age in all provenances, indicating that A. senegal is a potentially efficient nitrogen fixer and has an important role in t agroforestry development. The total above-ground contribution of fixed N to foliage growth in 4-year-old A. senegal trees was highest in the Rahad sand-soil provenance (46.7 kg N ha-1) and lowest in the Mazmoom clay-soil provenance (28.7 kg N ha-1). This study represents the first use of the δ15N method for estimating the N input by A. senegal in the gum belt of Sudan. Key words: Acacia senegal, agroforestry, clay plain, δ13C, δ15N, gum arabic, nutrient cycling, Ndfa, Sorghum bicolor, Sesamum indicum