Estudo experimental e teórico das propriedades magnéticas e supercondutoras dos compostos borocarbetos da série Y(Ni 1-x Mn x) 2 B2 C com x = 0,0, 0,01, 0,025, 0,05, 0,10 e 0,15

Apresentamos neste trabalho os resultados de um estudo experimental e teórico dos compostos borocarbetos supercondutores da série Y(Ni1-xMnx)2B2C com x = 0; 0,01; 0,025; 0,05; 0,10; 0,15. A principal motivação para este trabalho foi investigar a estrutura eletrônica e a possível formação do momento magnético sobre os átomos de impureza de Mn nos compostos Y(Ni1- xMnx)2B2C. O aparecimento do momento magnético localizado no sítio da impureza possibilitou estudar a influência do Mn sobre o mecanismo de quebra de pares supercondutores e sobre as propriedades magnéticas do composto. Os borocarbetos são compostos de estrutura cristalina tetragonal de corpo centrado e altamente anisotrópicos (c/a~3). São intermetálicos de alta temperatura crítica supercondutora Tc, com forte acoplamento elétron-fonon. Em alguns casos podem apresentar ordem magnética, supercondutividade e também coexistência ou competição energética entre ambos. As medidas de transporte eletrônico, em função da temperatura, foram feitas utilizando-se um detector síncroton baseado na técnica de quatro pontos operando na faixa de 4,2K até 300K. Essas medidas possibilitaram o estudo das propriedades relacionadas ao transporte eletrônico na fase supercondutora. Na fase normal, extraiu-se a dependência em energia da função espectral de fonons α² F (ω) para alguns compostos da série estudada. As medidas magnéticas em função da temperatura e do campo magnético foram feitas utilizando-se um SQUID (Superconducting Quantun Interference Device – Quantun Design Model MPMS XL). Tais medidas permitiram a caracterização das propriedades magnéticas de nossas amostras. Em particular determinou-se o valor, em regime de saturação, do momento magnético associado ao sítio cristalino do Mn. Foram determinadas também as correntes críticas supercondutoras usando o Modelo de estado crítico de Bean e a variação da temperatura crítica supercondutora (Tc) com a mudança do campo externo aplicado. As medidas magnéticas permitiram a obtenção do diagrama que relaciona o campo crítico inferior (HC1) e a temperatura, variando-se a concentração do átomo dopante de manganês. Foi feito um esforço teórico no sentido de interpretar os resultados experimentais. Para isso foram usados três modelos: O modelo de estado crítico de Bean já citado acima e um modelo baseado na fórmula de Ziman usando uma aproximação para a função espectral de fonons para descrever a resistividade no regime de alta temperatura. Além disto, usou-se o modelo de duas sub-redes para a descrição do momento magnético das impurezas de Mn, em função da concentração, na série Y(Ni ) ( 2 ω α F 1-xMnx)2B2C.

Two additions to Lucas's "inflation and welfare"

This work adds to Lucas (2000) by providing analytical solutions to two problems that are solved only numerically by the author. The first part uses a theorem in control theory (Arrow' s sufficiency theorem) to provide sufficiency conditions to characterize the optimum in a shopping-time problem where the value function need not be concave. In the original paper the optimality of the first-order condition is characterized only by means of a numerical analysis. The second part of the paper provides a closed-form solution to the general-equilibrium expression of the welfare costs of inflation when the money demand is double logarithmic. This closed-form solution allows for the precise calculation of the difference between the general-equilibrium and Bailey's partial-equilibrium estimates of the welfare losses due to inflation. Again, in Lucas's original paper, the solution to the general-equilibrium-case underlying nonlinear differential equation is done only numerically, and the posterior assertion that the general-equilibrium welfare figures cannot be distinguished from those derived using Bailey's formula rely only on numerical simulations as well.

Extração de metais (K, Mg, Ba, Ca, Cr, Mn, Li, Fe) de água produzida utilizando sistema microemulsionado

The produced water is a byproduct formed due to production of petroleum and carries with it a high amount of contaminants such as oil particles in suspension, organic compounds and metals. Thus, these latter pollutants are very difficult to treat because of its high solubility in water. The objective of this work is to use and evaluate a microemulsioned system to remove metals ( K , Mg , Ba , Ca , Cr , Mn , Li , Fe ) of synthetic produced water. For the extraction of metals, it was used a pseudoternary diagram containing the following phases: synthetic produced water as the aqueous phase (AP), hexane as organic phase (OP), and a cosurfactant/surfactant ratio equal to four (C/S = 4) as the third phase, where the OCS (saponified coconut oil) was used as surfactant and n-butanol as cosurfactant. The synthetic produced water was prepared in a bench scale and the region of interest in the diagram for the removal of metals was determined by experimental design called. Ten points located in the phase Winsor II were selected in an area with a large amount of water and small amounts of reagents. The samples were analyzed in atomic absorption spectrometer, and the results were evaluated through a statistical assesment, allowing the efficiency analysis of the effects and their interactions. The results showed percentages of extraction above 90% for the metals manganese, iron, chromium, calcium, barium and magnesium, and around 45% for metals lithium and potassium. The optimal point for the simultaneous removal of metals was calculated using statistical artifact multiple response function (MR). This calculation showed that the point of greatest extraction of metals occurs was the J point, with the composition [72% AP, 9% OP, 19% C/S], obtaining a global extraction percentage about 80%. Considering the aspects analyzed, the microemulsioned system has shown itself to be an effective alternative in the extraction of metals on synthetic produced water remediation

Estudo da labilidade de Cu(II), Cd(II), Mn(II) e Ni(II) em substâncias húmicas aquáticas utilizando-se membranas celulósicas organomodificadas

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Cobertura do solo, produção de biomassa e teores de Mn e Zn de alface no sistema orgânico

O objetivo deste trabalho foi avaliar o efeito da cobertura do solo com aveia preta e manutenção da palha sobre o terreno, bem como cobertura do solo com filme de polietileno preto, sobre a produção de biomassa e teores de Mn e Zn em alface cultivada no sistema orgânico, por dois anos consecutivos. Utilizaram-se cinco tratamentos: solo sem cobertura, coberto com filme de polietileno preto, coberto com aveia acamada, coberto com aveia ceifada e solo coberto com aveia na sua forma natural, para o cultivo de três cultivares de alface. O experimento seguiu delineamento experimental de blocos ao acaso, com quatro repetições e análise estatística com parcelas subdivididas. Concluiu-se que o cultivo de alface em sucessão à aveia preta, sobre a palha, promoveu produção satisfatória e apresentou adequados teores de manganês e zinco, equivalentes àqueles encontrados na literatura em diferentes sistemas de cultivo, e a cobertura do solo com plástico preto promoveu produção satisfatória com maior acúmulo de Zn no primeiro ano e menor de Mn no segundo.

A novel Mn-containing conducting metallopolymer obtained by electropolymerization in aqueous solution of a tetranuclear oxo-bridged manganese complex

The [Mn(4)(IV)O(5)(terpy)(4)(H(2)O)(2)](6+) complex shows great potential for electrode modification by electropolymerization using cyclic voltammetry. The electropolymerization mechanism was based on the electron transfer between dx(2)-y(2) orbitals of the metallic center and p pi orbital of the ligand.

Enzymeless Hydrogen Peroxide Sensor Based on Mn-containing Conducting Metallopolymer

The [(Mn4O5)-O-IV(terpy)(4)(H2O)(2)](6+) complex, show great potential for electrode modification by electropolymerization using cyclic voltammetry. The voltammetric behavior both in and after electropolymerization process were also discussed, where the best condition of electropolymerization was observed for low scan rate and 50 potential cycles. A study in glass electrode for better characterization of polymer was also performed. Electrocatalytic process by metal centers of the conducting polymer in H2O2 presence with an increase of anodic current at 0.85 V vs. SCE can be observed. The sensor showed great response from 9.9 x 10(-5) to 6.4 x 10(-4) mol L-1 concentration range with a detection limit of 8.8 x 10(-5) mol L-1, where the electrocatalytic mechanism was based on oxidation of H2O2 to H2O with consequently reduction of Mn-IV to Mn-III. After, the Mn-III ions are oxidized electrochemically to Mn-IV ions. (C) 2012 Elsevier Ltd .... Selection and/or peer-review under responsibility of the Symposium Cracoviense Sp. z.o.o.

Resonant excitation of Mn local vibrational modes in the higher order Raman spectra of nanocrystalline Ga(1-x)Mn(x)N films

The effect of manganese on the vibrational properties of Ga(1-x)Mn(x)N (0 <= x <= 0.18) films has been investigated by Raman scattering using 488.0 and 632.8 nm photon excitations. The first-order transverse and longitudinal optical GaN vibrational bands were observed in the whole composition range using both excitations, while the corresponding overtones, as well as a prominent peak located in 1238 cm(-1) (153.5 meV) were only observed in the Mn-containing films under 488.0 nm excitation. We propose that the peak observed at 1238 cm(-1) is due to resonant Mn local vibrational modes, the excitation process being related to electronic transitions involving the Mn acceptor band.

Structural and Electronic Effects of Incorporating Mn in TiO2 Films Grown by Sputtering: Anatase versus Rutile

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Disorder effects produced by the Mn and H incorporations on the optical absorption edge of Ga1-xMnxAs:H nanocrystalline films

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

The optical absorption edge of nanocrystalline Ga(1-x)Mn(x)N films deposited by reactive sputtering

We have focused on the optical absorption edge of nanocrystalline Ga(1-x)Mn(x)N (0.00 <= x <= 0.18) films deposited by reactive RF magnetron sputtering. The films obtained are nanocrystalline with grain sizes of about 25 nm, having wurtzite structure and strong orientation texture in the c-axis direction. The optical characterizations of the absorption edges were obtained in the 190-2600 nm spectral range. The increase of the Mn content causes an increase of the absorption coefficient which can be clearly noticed at low energies, and a quasi-linear decrease of the optical gap. Broad absorption bands observed around similar to 1.3 and similar to 2.2 eV were associated with transitions between the Mn acceptor level and the valence and conduction bands, respectively. The observed changes in the optical properties due to the Mn incorporation observed in these nanocrystalline films are similar to those reported for ferromagnetic GaMnN single-crystal films.

Preparação de membranas de acetato de celulose organomodificadas para adsorção dos íons Cu(II), Cd(II), Mn(II) e Ni(II)

Cellulose acetate polymeric membranes had been prepared by a procedure of two steps, combining the method of phase inversion and the technique of hydrolysis-deposition. The first step was the preparation of the membrane, and together was organomodified with tetraethylortosilicate and 3-aminopropyltrietoxysilane. Parameters that exert influence in the complexation of the metallic ion, as pH, time of complexation, metal concentration, had been studied in laboratory using tests of metal removal. The membranes had presented resistance mechanics and reactivity to cations, being able to be an alternative for the removal, daily pay-concentration or in the study of the lability of metals complexed.

Adsorção de Mn (II) e Zn (II) em soluções aquosas usando perlita expandida revestida com quitosana

In this work, chitosan was used as a coating of pure perlite in order to increase the accessibility of the groups OH- e NH2+the adsorptionof ions Mn2+ e Zn2+.The characterization results of the expanded perlite classified as microporous and whose surface area 3,176 m2 g-1after the change resulted in 4,664 m2g-1.From the thermogravimetry(TG) it was found that the percentage of coating was34,3%.The infrared analysis can prove the presence of groups Si-OH, Si-O e Al-O-Siresulting from the perlite and C=O, NH2and OH characterization of chitosan. The experiments on experiments on the adsorption of Mn and Zn were performed in the concentration range of10 a 50 mgL-1and the adsorption capacity inpH 5,8 e 5,2 was 19,49 and 23,09 mgg-1to 25 oC,respectively.The adsorption data were best fitted to Langmuir adsorption model to Langmuir adsorption model for both metalionsisindicative of monolayer adsorption. The kinetics of adsorption were calculated from the equation of Lagergren fitting the model pseudo-second-order for all initial concentrations, suggesting that adsorption of ions Mn2+ and Zn2+ follows the kinetics of pseudo-second-order and whose constant Speedk2(g/mg.min) are 0,105 e 3,98 and capacity and maximum removal qe 4,326 e 3,348,respectively.In this study we used a square wave voltammetry cathodic stripping voltammetry to quantify the adsorbed ions, and the working electrode glassy carbon, reference electrode silver / silver chloride and a platinum auxiliary electrode. The attainment of the peaks corresponding to ions Mn2+ and Zn2+ was evaluated in and electrochemical cell with a capacity of 30 mL using a buffer system (Na2HPO4/NaH2PO4)at pH 4 and was adjusted with solutionsH3PO4 0,1molL-1and NaOH 0,1 molL-1and addition of the analyte has been a cathodic peak in- 0,873 Vand detection limit of2,55x10-6molL-1para Zn.The dough used for obtaining the adsorption isotherm was 150 mg and reached in 120 min time of equilibrium for both metal ions.The maximum adsorption for 120 min with Mn concentration 20 mgL-1 and Zn 10 mgL-1,was91, 09 e 94, 34%, respectively

Estudo do desempenho de catalisadores tipo Ni/CexM1-xO2 (M = Zr ou Mn) na reação de oxidação parcial do metano

One of the main applications of methane is in the production of syngas, a mixture of hydrogen and carbon monoxide. Procedures used in this process are steam reforming, CO2 reforming, partial oxidation and autothermal reforming. The present study evaluated and compared the behavior of nickel catalysts supported on mixed oxides of cerium and manganese in the partial oxidation of methane with that of nickel catalysts supported on mixed oxides of cerium and zirconium. Mixed oxides of cerium and zirconium or cerium and manganese were synthesized using two different preparation methods, the polymeric precursor based on Pechini method and combustion reaction using a microwave. This was followed by impregnation with nickel content of 15 %. Samples were calcined at 300, 800 and 900 °C and characterized by specific surface area (SSA), X-ray fluorescence (XRF), X-ray diffraction (XRD), scanning electron microscopy (SEM), temperature programmed reduction (TPR) and the reaction of partial oxidation of methane. The specific areas of samples decrease with the rise in calcination temperature and after nickel impregnation. Metal-cerium solid solution was formed and the presence of other manganese species outside the solid solution structure was confirmed in the compound with the highest amounts of manganese oxides showed. With regard to scanning electron microscopy, supports based on cerium and zirconium prepared by Pechini method exhibited agglomerated particles without uniform geometry or visible pores on the surface. However, compounds containing manganese presented empty spaces in its structure. Through synthesis by combustion reaction, morphology acquired independently of the proposed composition demonstrated greater porosity in relation to Pechini synthesis. Although catalysts were prepared using different synthesis methods, the insertion of nickel showed very similar reduction profiles (TPR). In relation to nickel catalysts supported on mixed oxide of cerium and zirconium, there is an initial reduction of NiO species that present certain interaction with the support. This is followed by the reduction of Ce4+ in Ce3+ surface, with subsequent bulk reduction. For catalysts containing manganese, a reduction of nickel oxide species occurs, followed by two stages of reduction for species Mn2O3 in Mn3O4 and Mn3O4 in MnO, with subsequent reduction of bulk. With respect to partial oxidation reactions, the nickel catalyst supported on mixed oxide of cerium and zirconium, prepared using the Pechini method, exhibited CH4 conversion of approximately 80 %, with conversion of 81 % when prepared by combustion. This behavior continued for 10 hours of reaction. Manganese content was also found to directly influence catalytic activity of materials; the greater the manganese oxide content, the faster deactivation and destabilization occurred in the catalyst. In both synthesis methods, the nickel catalyst supported on mixed oxide of cerium and zirconium maintained an H2/CO ratio very close to 2 during the 10 hours of partial oxidation reaction. Samples containing manganese displayed smaller H2/CO ratios and lower performance in partial oxidation.