过量Mg~(2+)对土壤中酶活性的影响

目的研究过量Mg2+对土壤中脲酶、磷酸酶和过氧化氢酶活性的影响.方法通过在清洁土壤中投加不同质量浓度的MgC l2试剂,经过28 d的培养,期间在第1、3、7、14、28 d取样,测定土壤中的脲酶、磷酸酶和过氧化氢酶的活性.结果数据分析表明Mg2+对脲酶有激活作用,当Mg2+的质量分数为0.6%时,土壤脲酶活性提高最多,为91.6%,脲酶活性增加的程度为:0.6%>0.8%>0.4%>0.2%>1.0%>0,并且第1 d是观测脲酶变化的最佳时间.Mg2+对磷酸酶活性有先激活再抑制的作用,其活性在第3 d有大幅度增加,而从第14 d开始到第28 d,5个含不同质量分数Mg2+的土样,其磷酸酶活性全都低于空白试验。过氧化氢酶活性在试验的所有土样中均受到长效抑制.结论脲酶、磷酸酶和过氧化氢酶对Mg2+反映敏感,在Mg2+质量分数为0.6%时可以短期提高土壤肥力,但是长期大量的Mg2+介入土壤会严重影响土壤肥力,因此,可以考虑以Mg2+作为镁污染土壤的生态毒理指标.

Microstructure and mechanical properties of Mg-4.5Zn-xNd (x=0, 1 and 2, wt%) alloys

Microstructure and mechanical properties of Mg-4.5Zn-xNd (x = 0, 1 and 2, wt%) alloys heat-treated at 603 K for 2 It have been investigated. T-phase (an Mg-Zn-Nd ternary phase) was observed in the Nd containing alloys. The optimal mechanical properties were obtained in the Mg-4.5Zn-1Nd alloy, and the ultimate tensile strength and yield strength were 228 and 79 MPa, respectively. Through comparing with the Mg-4.5Zn alloy, the increments of ultimate tensile strength and yield strength were 51 and 17 MPa.

Microstructures and mechanical properties of the Mg-4.5Zn-xGd (x = 0, 2, 3 and 5) alloys

Microstructures and mechanical properties of the peak-aged Mg-4.5Zn-xGd (x = 0, 2, 3 and 5 wt.%) alloys have been investigated. The results showed that grain size increased with increasing Gd. Phase analysis showed that MgZn2 phase was observed in the Mg-4.5Zn alloy. While with Gd additions, Mg3Gd and Mg3Gd2Zn3 phases formed, and the volume fraction of the Mg3Gd2Zn3 phase increased with increasing Gd. Tensile test results indicated that the optimal mechanical properties were obtained in the Mg-4.5Zn-2Gd alloy, and the ultimate tensile strength and yield strength were 215 MPa and 121 MPa, respectively.

Microstructures and mechanical properties of as-cast Mg-5Y-3Nd-Zr-xGd (x=0, 2 and 4 wt.%) alloys

Mg-5Y-3Nd-0.6Zr-xGd (x = 0, 2 and 4 wt.%) alloys were prepared by metal mould casting technique, the structures and mechanical properties were investigated. The alloys were mainly composed of alpha-Mg solid solution and beta-phase. With increasing Gd content, Mg5RE phase increased and the grain was refined. The Mg-5Y-3Nd-2Gd-0.6Zr alloy exhibited highest ultimate tensile strength and Mg-5Y-3Nd-0.6Zr alloy showed highest yield strength at room temperature. With increasing amount of Gd, the thermal resistance was improved. The Mg-5Y-3Nd-4Gd-0.6Zr alloy exhibited highest UTS and YS at 250 degrees C, they were about 1.27 times higher than those of Gd-free alloy, which was mainly attributed to the increase of the beta-phase and Mg5RE strengthening phase.

Uniform Ln(OH)(3) and Ln(2)O(3) (Ln = Eu, Sm) Submicrospindles: Facile Synthesis and Characterization

Monodisperse hexagonal Ln(OH)(3) (Ln = Eu, Sm) submicrospindles with uniform morphology and size have been Successfully synthesized in a large scale via a Facile aqueous solution route from the mixture of aqueous solutions or LnCl(3) and NaOH at 5 degrees C without using any surfactant or template. The as-synthesized products are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), energy-dispersive X-ray (EDX) spectra, scanning electron microscopy (SEM), transmission electron microscopy (TEM), and high-resolution transmission electron microscopy (HRTEM). The SEM and TEM images show that the as-formed Ln(OH)(3) samples have a spindlelike shape with an equatorial diameter of 80-200 nm and a length of 500-900 nm, which are aggregates of even smaller nanoparticles.

Microstructures, mechanical properties and corrosion behavior of high-pressure die-cast Mg-4Al-0.4Mn-xPr (x=1, 2, 4, 6) alloys

Mg-4Al-0.4Mn-xPr (x = 1, 2, 4 and 6 wt.%) magnesium alloys were prepared successfully by the high-pressure die-casting technique. The microstructures, mechanical properties, corrosion behavior as well as strengthening mechanism were investigated. The die-cast alloys were mainly composed of small equiaxed dendrites and the matrix. The fine rigid skin region was related to the high cooling rate and the aggregation of alloying elements, such as Pr. With the Pr content increasing, the alpha-Mg grain sizes were reduced gradually and the amounts of the Al2Pr phase and All, Pr-3 phase which mainly concentrated along the grain boundaries were increased and the relative volume ratio of above two phases was changed. Considering the performance-price ratio, the Pr content added around 4 wt.% was suitable to obtain the optimal mechanical properties which can keep well until 200 degrees C as well as good corrosion resistance. The outstanding mechanical properties were mainly attributed to the rigid casting surface layer, grain refinement, grain boundary strengthening obtained by an amount of precipitates as well as solid solution strengthening.

Microstructures and mechanical properties of Mg-8Gd-0.6Zr-xNd (x=0, 1, 2 and 3 mass%) alloys

Mg-8Gd-0.6Zr-xNd (x = 0, 1, 2 and 3 mass%) alloys were prepared by metal mould casting method, and the microstructures, age hardening responses and mechanical properties have been investigated. The microhardness of the as-cast alloys is increased with increasing Nd content. The age hardening behavior and mechanical properties are enhanced significantly by adding Nd element. The peak ageing hardness of the Mg-8Gd-0.6Zr-3Nd alloy is 103, it is about 1.3 times more than that of the Mg-8Gd-0.6Zr alloy. The aged Mg-8Gd-0.6Zr-3Nd alloy exhibits maximum ultimate tensile strength and yield strength, and the values are 271 and 205 MPa at room temperature, 205 MPa and 150 MPa at 250 degrees C, respectively. Which are about 2 times higher than those of Mg-8Gd-0.6Zr alloy. The improved hardness and strength are mainly attributed to the fine dispersiveness Of Mg5RE and Mg12RE precipitates in the alloy.

Crystal structures of EtEDTB center dot 1.4C(2)H(5)OH center dot 5H(2)O and H4EtEDTB(ClO4)(4)center dot C2H5OH (EtEDTB=N, N, N ', N '-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine)

The crystal structures of EtEDTB.1.4C(2)H(5)OH.5H(2)O 1 and H4EtEDTB(ClO4)(4).C2H5OH 2 (EtEDTB = N, N,N',N'-tetrakis[2-(1-ethylbenzimidazolyl)methyl]-1,2-ethanediamine) have been determined by single-crystal X-ray diffraction method. Compound 1 crystallizes in the space group P(1) over bar with a = 11.489(2), b = 11.866(3), c = 12.002(3) Angstrom, alpha = 97.47(2), beta = 114.564(13), gamma = 114.11(2)degrees, V = 1266.6(5) Angstrom(3), Z = 1, M-r = 847.48, D-c = 1.111 g/cm(3), F(000) = 456 and mu(MoKalpha) = 0.076 mm(-1). A total of 5207 reflections were measured for 1, of which 4323 were independent. The structure of 1 was solved by direct methods and refined by full-matrix least-squares technique to the final R = 0.0706 and wR = 0.1802 for 1318 observed reflections with I > 2sigma(I). In the structure of 1, centrosymmetric EtEDTB molecules are linked by hydrogen bonds through water and ethanol to form 2-dimensional network. Compound 2 crystallizes in the space group C2/c with a = 24.260(5), b = 13.040(3), c = 17.680(4) Angstrom, beta = 97.50(3)degrees, V = 5545.2(2) Angstrom(3), Z = 4, M-r = 1140.80, D-c = 1.366 g/cm(3), F(000) = 2384 and mu(MoKalpha) = 0.289 mm(-1).

Synthesis, characterization and crystal structure of a new layered heterometallic coordination polymer {[(CuL) Sr-2(H2O)center dot Sr-2(H2O)(7)]center dot 2H(2)O center dot 0.5CH(3)OH}(n)

A copper-strontium heterometallic coordination polymer was synthesized and characterized by elemental analysis and IR spectra. The crystal structure was determined by single-crystal X-ray diffraction analyses. The title complex is a 2 D coordination polymer with the chemical formula [[(CuL)(2)Sr (H2O) center dot Sr-2 ((HO)-O-2)(7)]center dot 2H(2)O center dot 0.5CH(3)OH](n), where H4L = N-(2-hydroxybenzamido)-N'-(3-carboxylsalicylidene) ethylenediamine. Its structural unit is comprised of two adjacent units, which polymerized with each other to form a new layered heterometallic coordination polymer.

Determination of ultra-trace concentrations of elements in high purity tellurium by inductively coupled plasma mass spectrometry after Fe(OH)(3) coprecipitation

In this work, a method was established for the determination of impurities in high purity tellurium by inductively coupled plasma mass spectrometry (ICP-MS) after Fe(OH)(3) coprecipitation. After comparison of coprecipitation ability and separation efficiency between Fe(OH), and Al(OH)(3), Fe(OH)(3) was chosen as the precipitate. A separation factor of 160 for 200 mg tellurium was obtained under conditions of pH 9 and 2 mg of Fe3(+). The 13 elements, such as Bi, Sn, Pb, In, Tl, Cd, Cu, Co, Ni, Zn, Ti, Be and Zr, could be almost completely coprecipitated under these conditions. In addition, Te memory effect imposed on the ICP-MS instrument was assessed, as well as Te matrix effect that caused the low recovery of Ga, As, Sb and V in real sample was discussed. Finally, the method was evaluated through recovery test and was applied to practical sample analysis, with detection limits of most of the elements being below 0.15 mug g(-1) and R.S.D. below or at approximately 10%, which indicated that this method could fully satisfy the requirements for analysis of 99.999% similar to 99.9999% high purity Te.

A two-dimensional molybdenum (V) phosphate with covalently bonded transition metal coordination complexes: hydrothermal synthesis and structure characterization of Na-2[{Mn(phen)(2)(H2O)}{Mn(phen)(2)}(3){Mn (Mo12O24)-O-V (HPO4)(6)(PO4)(2)(OH)(6)}] center dot 4H(2)O (phen=1,10-phenanthroline)

An organic-inorganic hybrid molybdenum phosphate, Na-2[{Mn(phen)(2)(H2O)} {Mn(phen)(2)}(3){(MnMo12O24)-O-v (HPO4)(6)(PO4)(2) (OH)(6)}] . 4H(2)O (phen=1,10-phenanthroline), involving molybdenum present in V oxidation state and covalently bonded transition metal coordination complexes, has been hydrothermally synthesized and structurally characterized by single-crystal X-ray diffraction. Deep brown-red crystals are formed in the triclinic system, space group P (1) over bar, a=16.581(l)Angstrom, b=18.354(1)Angstrom, c=24.485(2)Angstrom, alpha=80.589(l)degrees, beta=71.279(1)degrees, gamma=67.084(1)degrees, V=6493.8(8)Angstrom(3), Z=2, lambda(MoKalpha)=0.71073Angstrom (R(F)=0.0686 for 29,053 reflections). Data were collected on a Bruker Smart Apex CCD diffractometer at 293 K in the range of 1.76 < theta < 28.06degrees using omega-2theta scans technique. The structure of the title compound may be considered to be based on {Mo6O12(HPO4)(3)(PO4)(OH)(3)} units bonded together with {Mn(phen)(2)} subunits into a two-dimensional network. Two types of tunnels are observed in the solid of the title compound.

BaMAl_(10)O_(17)(M=Be,Mg,Ca,Zn,Cd,Mn,Co,Li)体系的合成、结构和Eu~(2+)在其中的发光

在BaMAl10O17 体系中 ,将M扩大到除镁以外的其它离子 ,研究和讨论了离子半径与基质结构的形成关系 ,提出能稳定(形成)尖晶石结构的M离子有相应的磁铅矿或β Al2O3 结构的化合物存在的思想 ,并研究了Eu2 +在体系中的发光性能。结果表明 ,M=Zn,Cd,Mn,Co,Li时可形成 β Al2O3 结构化合物 ,M=Ca,Be时不能形成这类结构 ,Ca形成多相共存 ,Be形成一未知相 ;Eu2 +在M=Li,Be,Zn体系中具有良好的发光性能 ,发射波长450nm ,半高宽在50nm附近 ,将是一类很有前途的新的蓝色发光材料 ,Eu2 +在M=Mn的体系中存在Eu2 +和Mn2 +的同时发射 ,在M=Cd体系中 ,Eu2 +产生一双重宽带发射。对实验结果进行了合理的解释

ABF_3:Eu,Gd(A:K,Li;B:Ba,Mg)中Gd~(3+)→Eu~(2+)的能量传递

通过高温固相反应法,在高纯N_2气氛中合成了BaLiF_3,KMgF_3中单掺和双掺Eu,Gd的ABF_3型复合氟化物。研究了各类掺杂体系的光谱特性,观察到了Gd~(3+)→Eu~(2+)的能量传递,分析了能量传递过程,探讨了能量传递机理,并讨论了Gd~(3+)和Eu~(2+)的取代格位。

Hydrothermal synthesis of the two-dimensional coordination polymer {[Fe(phen)(OH)](bta)(0.5)}(n) (phen=1,10-phenanthroline, bta=benzene-1,2,4,5-tetracaboxylate)

The title two-dimensional coordination polymer was synthesised and characterised by X-ray diffraction analysis.

A manganese molybdenum phosphate with a tunnel: hydrothermal synthesis, structure and catalytic properties of (NH3CH2CH2NH3)(10-)H3O)(3)(H5O2)Na-2[MnMo12O24(OH)(6)(PO4)(4)(PO3OH)(4)]-[MnMo12O24(OH)(6)(PO4)(6)(PO3OH)(2)] center dot 9H(2)O

A manganese molybdenum phosphate, (NH3CH2CH2NH3)(10)(H3O)(3)(H5O)Na-2[MnMo12O24(OH)(6) (PO4)(4)(PO3OH)(4)][MnMo12O24 (OH)(6)(PO4)(6)(PO3OH)(2)]. 9H(2)O, has been hydrothermally synthesized and structurally characterized by single crystal X-ray diffraction. The structure of this compound may be considered to be two [Mo6O12(OH)(3)(PO4)(2)(HPO4)(2)](7-) units bonded together by a manganese atom, although several P-O groups are not protonated on account of coordination to a Na+ cation. One-dimensional tunnels were formed in the solid. A probe reaction of the oxidation of acetaldehyde with H2O2 using this compound as catalyst was carried out in a liquid-solid system, showing that the manganese molybdenum phosphate has high catalytic activity in the reaction.