Experimental evaluation of layout designs for 3 × 3 MIMO-enabled radio-over-fiber distributed antenna systems

This paper experimentally demonstrates that, for two representative indoor distributed antenna system (DAS) scenarios, existing radio-over-fiber (RoF) DAS installations can enhance the capacity advantages of broadband 3 × 3 multiple-input-multiple-output (MIMO) radio services without requiring additional fibers or multiplexing schemes. This is true for both single-and multiple-user cases with a single base station and multiple base stations. First, a theoretical example is used to illustrate that there is a negligible improvement in signal-to-noise ratio (SNR) when using a MIMO DAS with all N spatial streams replicated at N RAUs, compared with a MIMO DAS with only one of the N streams replicated at each RAU for N ≤ 4. It is then experimentally confirmed that a 3 × 3 MIMO DAS offers improved capacity and throughput compared with a 3 × 3 MIMO collocated antenna system (CAS) for the single-user case in two typical indoor DAS scenarios, i.e., one with significant line-of-sight (LOS) propagation and the other with entirely non-line-of-sight (NLOS) propagation. The improvement in capacity is 3.2% and 4.1%, respectively. Then, experimental channel measurements confirm that there is a negligible capacity increase in the 3 × 3 configuration with three spatial streams per antenna unit over the 3 × 3 configuration with a single spatial stream per antenna unit. The former layout is observed to provide an increase of ∼1% in the median channel capacity in both the single-and multiple-user scenarios. With 20 users and three base stations, a MIMO DAS using the latter layout offers median aggregate capacities of 259 and 233 bit/s/Hz for the LOS and NLOS scenarios, respectively. It is concluded that DAS installations can further enhance the capacity offered to multiple users by multiple 3 × 3 MIMO-enabled base stations. Further, designing future DAS systems to support broadband 3 × 3 MIMO systems may not require significant upgrades to existing installations for small numbers of spatial streams. © 2013 IEEE.

Effect of counterpart on the tribological behavior and tribo-induced phase transformation of Si

The tribological behaviors and phase transformation of single crystal silicon against Si3N4, Ruby and steel were investigated in this study. It was found that the strong chemical action between silicon and Fe was the key factor to the tribological behavior of silicon as slid against steel. SEM and Raman spectroscopy indicated that phase transformation of single crystal silicon occurred during the running-in period at low sliding velocity as slid against Si3N4 and Ruby. and gave birth to single or a mixture phase of Si-III, Si-XII and amorphous silicon. The high hardness of counterpart and the absence of chemical action between silicon and counterpart facilitated the phase transformation of single crystal silicon. (C) 2008 Elsevier Ltd. All rights reserved.

Characterization of entanglement transformation via group representation theory

Entanglement transformation of composite quantum systems is investigated in the context of group representation theory. Representation of the direct product group SL(2, C) circle times SL(2, C), composed of local operators acting on the binary composite system, is realized in the four-dimensional complex space in terms of a set of novel bases that are pseudo-orthonormalized. The two-to-one homomorphism is then established for the group SL(2, C) circle times SL(2, C) onto the SO(4, C). It is shown that the resulting representation theory leads to the complete characterization for the entanglement transformation of the binary composite system.

A complex Fourier transformation study of the contactless electroreflectance of an undoped-n(+) GaAs structure

Complex Fourier transformation (CFT) has been employed to analyse contactless electroreflectance (CER) spectra from an undoped-n(+) GaAs structure with various ac modulations and dc bias voltages. The CFT spectra of CER have been compared with those of photoreflectance (PR). It has been found that the CER non-flat modulation is between the built-in electric field and a larger electric field which increases with the modulation voltage. The result has been explained by the screening of the applied modulation electric field in one of the two half modulation cycles and the trapping of electrons in surface states in the other half modulation cycle. The dc bias does not change the CER spectra, hence their CFT spectra. This is because of the screening of the applied dc bias electric field.

Local transformation of mixed states of two qubits to Bell diagonal states

The optimal entanglement manipulation for a single copy of mixed states of two qubits is to transform it to a Bell diagonal state. In this paper we derive an explicit form of the local operation that can realize such a transformation. The result obtained is universal for arbitrary entangled two-qubit states and it discloses that the corresponding local filter is not unique for density matrices with rank n = 2 and can be exclusively determined for that with n = 3 and 4. As illustrations, a four-parameter family of mixed states are explored, the local filter as well as the transformation probability are given explicitly, which verify the validity of the general result.

BPEL流程监视的可视化实现

When a BPEL process is executed,it is necessary to dynamically monitor the process.BPEL is a executable language,which is not suitable for visual monitoring.On the other hand,BPMN is designed to visually describe business process and is more intuitive for monitoring.To visually monitor a BPEL process, transformation from BPEL to BPMN is necessary.However,current study of transformation from BPEL to BPMN does not support the transformation of"link"activity.Besides,no work has been done to add supplementary information into BPMN during transformation.In this paper,we transform nested BPEL process into a flat BPMN process graph without hierarchy through applying a flattening strategy.Especially, we analyze various scenarios of the transformation of link activity,and provide a method to deal with it. Besides,we analyze the mapping between BPEL activities and BPMN graph,through which we found out that some supplementary information cannot automatically obtained from BPEL process.These supplementary information need to be added during transformation.At the end of this paper,we present the structure of our monitoring tool which is based on our transformation algorithm.

Coordination-Induced Formation of One-Dimensional Nanostructures of Europium Benzene-1,3,5-tricarboxylate and Its Solid-State Thermal Transformation

Novel one-dimensional europium benzene-1,3,5-tricarboxylate compressed nanorods have been synthesized oil it large scale through direct precipitation in solution phase under moderate conditions without the assistance of any surfactant, catalyst, or template. The obtained nanorods have widths of about 50-100 not, thicknesses of 10-20 nm, and lengths ranging from a few hundred nanometers to several micrometers. X-ray powder diffraction. elemental analysis, Fourier transform infrared Studies, and thermogravimetric and differential thermal analysis show that the nanorods have the structural formula of Eu(1,3,5-BTC)center dot 6H(2)O. Upon UV excitation, these nanorods exhibit a highly efficient luminescence. which comes from the Eu3+ ions. Moreover, Eu2O3 nanorods Could also be obtained via a thermal decomposition method using the corresponding complex as a precursor. This synthetic route is promising for the preparation of other one-dimensional crystalline nanomaterials because of its simplicity and the low cost of the starting reagents.

Three-stage transformation of chlorophyll transient fluorescence pattern under sustained dehydration and the discovery of critical water content in seaweeds

The chlorophyll fluorescence kinetics of marine red alga Grateloupia turutunt Yamada, green alga Ulva pertusa Kjellm and brown alga Laminaria japonica Aresch during natural sustained dehydration were monitored and investigated. The pulse amplified modulation (PAM) system was used to analyze the distinct fluorescence parameters during thallus dehydration. Results proved that the fluorescence kinetics of different seaweed all showed three patterns of transformation with sustained water loss. These were: 1) peak kinetic pattern (at the early stage of dehydration fluorescence enhanced and quenched subsequently, representing a normal physiological state). 2) plateau kinetic pattern (with sustained water loss fluorescence enhanced continuously but quenching became slower, finally reaching its maximum). 3) Platform kinetic pattern (fluorescence fell and the shape of kinetic curve was similar to plateau kinetic pattern). A critical water content (CWC) could be found and defined as the percentage of water content just prior to the fluorescence drop and to be a significant physiological index for evaluation of plant drought tolerance. Once thallus water content became lower than this value the normal peak pattern can not be recovered even through rehydration, indicating an irreversible damage to the thylakoid membrane. The CWC value corresponding to different marine species were varied and negatively correlated with their desiccation tolerance, for example. Laminaria japonica had the highest CWC value (around 90%) and the lowest dehydration tolerance of the three. In addition, a fluorescence "burst" was found only in red algae during rehydration. The different fluorescence parameters F-o, F-v and F-v, F-m were measured and compared during water loss. Both F-o and F-v increased in the first stage of dehydration but F-v/F-m. kept almost constant. So the immediate response of in vivo chlorophyll fluorescence to dehydration was an enhancement. Later with sustained dehydration F-o increased continuously while F-v decreased and tended to become smaller and smaller. The major changes in fluorescence (including fluorescence drop during dehydration and the burst during rehydration) were all attributed to the change in F-o instead of F-v This significance of F-o indicates that it is necessary to do more research on F-o as well as on its relationship with the state of thylakoid membrane.

Transformation field method for calculating the effective properties of isotropic graded composites having arbitrary shapes

A method of transformation field is developed to estimate the effective properties of graded composites whose inclusions have arbitrary shapes and gradient profiles by means of a periodic cell model. The boundary-value problem of graded composites having arbitrary inclusion shapes is solved by introducing the transformation field into the inclusion region. As an example, the effective dielectric response of isotropic graded composites having arbitrary shapes and gradient profiles is handled by the transformation field method (TFM). Moreover, TFM results are validated by the exact solutions of isotropic graded spherical inclusions having a power-law profile and good agreement is obtained in the dilute limit. Furthermore, it is found that the inclusion shapes and the parameters of the gradient profiles can have profound effect on the effective properties of composite systems at high concentration of inclusions.

Phase transformation in the surface region of zirconia detected by UV Raman spectroscopy

The phase transformation of zirconia from tetragonal to monoclinic is characterized by UV Raman spectroscopy, visible Raman spectroscopy, and XRD. Electronic absorption Of ZrO2 in the UV region makes UV Raman spectroscopy more sensitive at the surface region than XRD or visible Raman spectroscopy. Zirconia changes from the tetragonal phase to the monoclinic phase with calcination temperatures elevated and monoclinic phase is always detected first by UV Raman spectroscopy for the samples calcined at lower temperatures than that by XRD and visible Raman spectroscopy. When the phase of zirconia changes from tetragonal to monoclinic, the slight changes of the phase at very beginning can be detected by UV Raman spectroscopy. UV Raman spectra clearly indicate that the phase transition takes place initially at the surface regions. It is found that the phase change from tetragonal to monoclinic is significantly retarded when amorphous Zr(OH)(4) was agglomerated to bigger particles and the particle agglomeration of amorphous zirconium hydroxide is beneficial to the stabilization of t-ZrO2 phase.

An Accountable Source-To-Source Transformation System

Though one is led to believe that program transformation systems which perform source-to-source transformations enable the user to understand and appreciate the resulting source program, this is not always the case. Transformations are capable of behaving and/or interacting in unexpected ways. The user who is interested in understanding the whats, whys, wheres, and hows of the transformation process is left without tools for discovering them. I provide an initial step towards the solution of this problem in the form of an accountable source-to-source transformation system. It carefully records the information necessary to answer such questions, and provides mechanisms for the retrieval of this information. It is observed that though this accountable system allows the user access to relevant facts from which he may draw conclusions, further study is necessary to make the system capable of analyzing these facts itself.

Changes in innovation styles - comprehensive study of the changes in innovation styles to identify the causes and effects of different influencing factors and capabilities to create a general innovation pattern.

An investigation in innovation management and entrepreneurial management is conducted in this thesis. The aim of the research is to explore changes of innovation styles in the transformation process from a start-up company to a more mature phase of business, to predict in a second step future sustainability and the probability of success. As businesses grow in revenue, corporate size and functional complexity, various triggers, supporters and drivers affect innovation and company's success. In a comprehensive study more than 200 innovative and technology driven companies have been examined and compared to identify patterns in different performance levels. All of them have been founded under the same formal requirements of the Munich Business Plan Competition -a research approach which allowed a unique snapshot that only long-term studies would be able to provide. The general objective was to identify the correlation between different factors, as well as different dimensions, to incremental and radical innovations realised. The 12 hypothesis were formed to prove have been derived from a comprehensive literature review. The relevant academic and practitioner literature on entrepreneurial, innovation, and knowledge management as well as social network theory revealed that the concept of innovation has evolved significantly over the last decade. A review of over 15 innovation models/frameworks contributed to understand what innovation in context means and what the dimensions are. It appears that the complex theories of innovation can be described by the increasing extent of social ingredients in the explanation of innovativeness. Originally based on tangible forms of capital, and on the necessity of pull and technology push, innovation management is today integrated in a larger system. Therefore, two research instruments have been developed to explore the changes in innovations styles. The Innovation Management Audits (IMA Start-up and IMA Mature) provided statements related to product/service development, innovativeness in various typologies, resources for innovations, innovation capabilities in conjunction to knowledge and management, social networks as well as the measurement of outcomes to generate high-quality data for further exploration. In obtaining results the mature companies have been clustered in the performance level low, average and high, while the start-up companies have been kept as one cluster. Firstly, the analysis exposed that knowledge, the process of acquiring knowledge, interorganisational networks and resources for innovations are the most important driving factors for innovation and success. Secondly, the actual change of the innovation style provides new insights about the importance of focusing on sustaining success and innovation ii 16 key areas. Thirdly, a detailed overview of triggers, supporters and drivers for innovation and success for each dimension support decision makers in putting their company in the right direction. Fourthly, a critical review of contemporary strategic management in conjunction to the findings provides recommendation of how to apply well-known management tools. Last but not least, the Munich cluster is analysed providing an estimation of the success probability of the different performance cluster and start-up companies. For the analysis of the probability of success of the newly developed as well as statistically and qualitative validated ICP Model (Innovativeness, Capabilities & Potential) has been developed and applied. While the model was primarily developed to evaluate the probability of success of companies; it has equal application in the situation to measure innovativeness to identify the impact of various strategic initiatives within small or large enterprises. The main findings of the model are that competitor, and customer orientation and acquiring knowledge important for incremental and radical innovation. Formal and interorganisation networks are important to foster innovation but informal networks appear to be detrimental to innovation. The testing of the ICP model h the long term is recommended as one subject of further research. Another is to investigate some of the more intangible aspects of innovation management such as attitude and motivation of mangers. IV

Islamic corporate financing : does it promote profit and loss sharing?

Islamic financing instruments can be categorised into profit and loss/risk sharing and non-participatory instruments. Although profit and loss sharing instruments such as musharakah are widely accepted as the ideal form of Islamic financing, prior studies suggest that alternative instruments such as murabahah are preferred by Islamic banks. Nevertheless, prior studies did not explore factors that influence the use of Islamic financing among non-financial firms. Our study fills this gap and contributes new knowledge in several ways. First, we find no evidence of widespread use of Islamic financing instruments across non-financial firms. This is because the instruments are mostly used by less profitable firms with higher leverage (i.e., risky firms). Second, we find that profit and loss sharing instruments are hardly used, whilst the use of murabahah is dominant. Consistent with the prediction of moral-hazard-risk avoidance theory, further analysis suggests that users with a lower asset base (to serve as collateral) are associated with murabahah financing. Third, we present a critical discourse on the contentious nature of murabahah as practised. The economic significance and ethical issues associated with murabahah as practised should trigger serious efforts to steer Islamic corporate financing towards risk-sharing more than the controversial rent-seeking practice.

Poly-transformation

King, R. D. and Ouali, M. (2004) Poly-transformation. In proceedings of 5th International Conference on Intelligent Data Engineering and Automated Learning (IDEAL 2004). Springer LNCS 3177 p99-107

Fuzzy interpolative reasoning via scale and move transformation

Z. Huang and Q. Shen. Fuzzy interpolative reasoning via scale and move transformation. IEEE Transactions on Fuzzy Systems, 14(2):340-359.