Tehokalastuksen vaikutukset Lappajärvessä : Kalastus elinkeinoksi Lappajärvellä -hankkeen vuosien 2001-2006 seurannan loppuraportti

Lappajärven, Etelä-Pohjanmaan suurimman järven, ekologinen tila on heikentynyt ja se luokitellaan nykyisin tyydyttäväksi. Rehevöityminen, 1990-luvun muikkukato ja yhteiskunnan rakennemuutos ovat vähentäneet kalastajien ja kalansaaliin määrää. Ammattikalastuksen edellytysten parantamiseksi toteutettiin vuosina 2001–2004 ”Kalastus elinkeinoksi Lappajärvellä” – hanke. Hankkeen vaikutuksia kalastoon ja järven ekosysteemiin seurattiin vuosina 2001–2006. Kokonaissaalis vuosina 2001–2004 oli 1655 tonnia (n. 29 kg/ha/vuosi). Vaikka saalistavoitetta (2100 tn) ei täysin saavutettu, oli hankkeella runsaasti myönteisiä, joskin osin vähäisiä tai epävarmoja vaikutuksia järven tilaan ja kalastoon. Kalastajien yksikkösaaliit etenkin kuhan ja isokokoisen ahvenen osalta nousivat hankkeen alussa. Loppuvuosina yksikkösaaliiden kehitys oli osittain ristiriitaista. Ulapan taloudellisesti vähempiarvoinen kalasto, varsinkin kuorekanta harveni selvästi. Muikku puolestaan lisääntyi ja pysyi runsaana. Kuhan ja isokokoisen ahvenen lisääntymistä selittivät pääosin lämpimät kesät ja kuhan onnistuneet istutukset. Petokalat, etenkin kuha, voivat osaltaan säädellä Lappajärven ulapan planktonsyöjäkalojen kantoja ja toisaalta estää särjen siirtymistä ulapalle. Tehokalastuksen loputtua alkoi näkyä merkkejä kalakantojen palautumisesta takaisin kohti lähtötilannetta. Rantavyöhykkeellä hankkeen vaikutukset jäivät selvästi vähäisemmiksi kuin ulapalla. Eläinplankton lisääntyi hieman ylemmissä vesikerroksissa, mutta tilanne alkoi palautua ennalleen hankkeen jälkeen. Sinileväkukinnot vaikuttivat vähentyneen hankkeen aikana, tosin kukintojen voimakas vaihtelu vaikeutti arviointia. Tehokalastus ja vesiensuojelun tehostuminen vähensivät fosforipitoisuuksia, tosin myös vähäsateiset vuodet vaikuttivat vähenemiseen. Pitoisuuksien lasku jatkui hankkeen jälkeen. Hanketta edeltänyt klorofyllipitoisuuksien kasvusuuntaus pysähtyi ja pitoisuustaso vakiintui. Tehokalastus pienensi klorofylli/fosfori-suhdetta ja vähensi sisäistä kuormitusta, mutta vaikutus alkoi heiketä hankkeen loputtua. Typpipitoisuuksiin, veden väriin tai näkösyvyyteen kalastus ei vaikuttanut. Tehokalastuksella voidaan parantaa Lappajärven tilaa, mutta kalastuksen on oltava jatkuvaa. Saalistavoitteeksi voisi riittää n. 20-30 kg/ha vuodessa, mutta samalla on jatkettava ulkoisen kuormituksen vähentämistä. Kalastuksen tulisi kohdistua arvokalojen lisäksi myös vähempiarvoisiin kalalajeihin ja samalla on tuettava petokalakantojen vahvistumista.

Improved order fulfillment in paper production

For the paper mill profitability it is crucial to minimize overproduction and underproduction. Overproduction and underproduction both generate undesired costs and profit losses in paper mill production. This master’s thesis examines paper production order fulfillment subject from paper production level point of view. Research and development approach is selected due to clarification requirements in lately implemented manufacturing execution system. Manufacturing execution systems are generally expected to offer reliable and accurate information about mill production details. However, confusions are likely to occur after implementation of new manufacturing execution system. These confusions are usually harmful and become cumulatively more influential the longer they keep occurring. In this master’s thesis is presented actions to improve order fulfillment at paper mill production level. Central points of the improvement actions are a model for successful order fulfillment in paper mill production and manufacturing execution system catalogue configuration redesign. Improvement actions are implemented in Jokilaakso paper production plant and it is examined as a case study. In the end of this master’s thesis is presented performance measurements which demonstrate order fulfillment from case Jokilaakso.

Profile of cortisol, glycaemia, and blood parameters of American Bullfrog tadpoles Lithobates catesbeianus exposed to density and hypoxia stressors

The aim of this study was to evaluate alterations to the physiological profile (cortisol, glycaemia, and blood parameters) of Lithobates catesbeianus caused by the stressors density and hypoxia. The organisms were in the prometamorphosis stage and exposed to different tadpole densities: 1 tadpole/L (T1), 5 tadpoles/L (T2), and 10 tadpoles/L (T3) for 12 days. The blood was collected through the rupture of the caudal blood vessel and collected under normoxia (immediate collection) and hypoxia (after 15 minutes of air exposure) conditions. Cortisol levels rose on the fourth and eighth days of treatment and returned to basal levels by the end of the experiment. The stressor mechanisms tested did not affect glycaemia. White blood cells (total number of lymphocytes, neutrophils, and eosinophils) showed a significant difference at the twelfth day of the experiment when compared with the start of the experiment. We concluded that, under controlled conditions, a density of up to 10 tadpoles/L and air exposure for 15 minutes did not cause harmful physiological alterations during the experimental period. The answer to these stressors maybe was in another hormonal level (corticosterone).

Identification of Some Additional Loss Components in High-Power Low-Voltage Permanent Magnet Generators

Permanent magnet generators (PMG) represent the cutting edge technology in modern wind mills. The efficiency remains high (over 90%) at partial loads. To improve the machine efficiency even further, every aspect of machine losses has to be analyzed. Additional losses are often given as a certain percentage without providing any detailed information about the actual calculation process; meanwhile, there are many design-dependent losses that have an effect on the total amount of additional losses and that have to be taken into consideration. Additional losses are most often eddy current losses in different parts of the machine. These losses are usually difficult to calculate in the design process. In this doctoral thesis, some additional losses are identified and modeled. Further, suggestions on how to minimize the losses are given. Iron losses can differ significantly between the measured no-load values and the loss values under load. In addition, with embedded magnet rotors, the quadrature-axis armature reaction adds losses to the stator iron by manipulating the harmonic content of the flux. It was, therefore, re-evaluated that in salient pole machines, to minimize the losses and the loss difference between the no-load and load operation, the flux density has to be kept below 1.5 T in the stator yoke, which is the traditional guideline for machine designers. Eddy current losses may occur in the end-winding area and in the support structure of the machine, that is, in the finger plate and the clamping ring. With construction steel, these losses account for 0.08% of the input power of the machine. These losses can be reduced almost to zero by using nonmagnetic stainless steel. In addition, the machine housing may be subjected to eddy current losses if the flux density exceeds 1.5 T in the stator yoke. Winding losses can rise rapidly when high frequencies and 10–15 mm high conductors are used. In general, minimizing the winding losses is simple. For example, it can be done by dividing the conductor into transposed subconductors. However, this comes with the expense of an increase in the DC resistance. In the doctoral thesis, a new method is presented to minimize the winding losses by applying a litz wire with noninsulated strands. The construction is the same as in a normal litz wire but the insulation between the subconductors has been left out. The idea is that the connection is kept weak to prevent harmful eddy currents from flowing. Moreover, the analytical solution for calculating the AC resistance factor of the litz-wire is supplemented by including an end-winding resistance in the analytical solution. A simple measurement device is developed to measure the AC resistance in the windings. In the case of a litz-wire with originally noninsulated strands, vacuum pressure impregnation (VPI) is used to insulate the subconductors. In one of the two cases studied, the VPI affected the AC resistance factor, but in the other case, it did not have any effect. However, more research is needed to determine the effect of the VPI on litz-wire with noninsulated strands. An empirical model is developed to calculate the AC resistance factor of a single-layer formwound winding. The model includes the end-winding length and the number of strands and turns. The end winding includes the circulating current (eddy currents that are traveling through the whole winding between parallel strands) and the main current. The end-winding length also affects the total AC resistance factor.

Mäskin sisältämän ligniinin modifiointi PCD-hapetuksella

Teoriaosassa tutkittiin mäskin muodostumista oluentuotantoprosessissa, ligniiniä ja sen pilkkoutumista hapetuksella, eri kehittyneitä hapetusmenetelmiä ja hapetuksella saatavia potentiaalisia pääkomponentteja. Kehittyneissä hapetusmenetelmissä keskityttiin pääasiassa pulssitettuun koronapurkaukseen perustuvaan PCD-menetelmään (Pulsed Corona Discharge). Tutkittavana pääkomponenttina toimi glyoksyylihappo. Työn kokeellisessa osassa tutkittiin mäskistä erotetun ligniinin pilkkoutumista PCD-hapetuksella. Tässä menetelmässä hapetus perustuu sähköpurkauksen aikana syntyvien hydroksyyliradikaalien ja otsonin muodostumiseen, jotka voivat toimia hapettimina. Kokeissa käytettiin oluentuotannosta saatua mäskiä, josta ligniiniä liuotettiin natriumhydroksidi-vesi-liuoksen avulla uuttamalla.. Tämän jälkeen liuosta käsiteltiin PCD laitteistossa. PCD-käsiteltyä tuotetta analysoitiin mittaamalla ligniinin ja aldehydien pitoisuudet siitä spektrofotometrin avulla. Työn tarkoituksena on tutkia PCD hapetusmenetelmän soveltuvuutta mäskin sisältämän ligniinin muokkaamiseen siten, että siitä syntyvää tuotetta voitaisiin käyttää jossakin muussa sovelluksessa, kuten esimerkiksi lääkkeiden raaka-aineena lääketeollisuudessa. PCD hapetusmenetelmä on koronasähköpurkauksiin perustuva laite, jota käytetään pääasiassa vedenpuhdistuksessa hajoittamaan haitallisia orgaanisia yhdisteitä. Tämän työn perusteella ligniiniä hajosi, aldehydejä muodostui ja hapetusnäytteiden pH laski hapetusajan kasvaessa. Tämä viittasi vahvasti glyoksyylihapon muodostumiseen PCD-laitteistossa.

Research and development of III-V semiconductor surfaces for improved device interfaces

This thesis is devoted to understanding and improving technologically important III-V compound semiconductor (e.g. GaAs, InAs, and InSb) surfaces and interfaces for devices. The surfaces and interfaces of crystalline III-V materials have a crucial role in the operation of field-effect-transistors (FET) and highefficiency solar-cells, for instance. However, the surfaces are also the most defective part of the semiconductor material and it is essential to decrease the amount of harmful surface or interface defects for the next-generation III-V semiconductor device applications. Any improvement in the crystal ordering at the semiconductor surface reduces the amount of defects and increases the material homogeneity. This is becoming more and more important when the semiconductor device structures decrease to atomic-scale dimensions. Toward that target, the effects of different adsorbates (i.e., Sn, In, and O) on the III-V surface structures and properties have been investigated in this work. Furthermore, novel thin-films have been synthesized, which show beneficial properties regarding the passivation of the reactive III-V surfaces. The work comprises ultra-high-vacuum (UHV) environment for the controlled fabrication of atomically ordered III-V(100) surfaces. The surface sensitive experimental methods [low energy electron diffraction (LEED), scanning tunneling microscopy/spectroscopy (STM/STS), and synchrotron radiation photoelectron spectroscopy (SRPES)] and computational density-functionaltheory (DFT) calculations are utilized for elucidating the atomic and electronic properties of the crucial III-V surfaces. The basic research results are also transferred to actual device tests by fabricating metal-oxide-semiconductor capacitors and utilizing the interface sensitive measurement techniques [capacitance voltage (CV) profiling, and photoluminescence (PL) spectroscopy] for the characterization. This part of the thesis includes the instrumentation of home-made UHV-compatible atomic-layer-deposition (ALD) reactor for growing good quality insulator layers. The results of this thesis elucidate the atomic structures of technologically promising Sn- and In-stabilized III-V compound semiconductor surfaces. It is shown that the Sn adsorbate induces an atomic structure with (1×2)/(1×4) surface symmetry which is characterized by Sn-group III dimers. Furthermore, the stability of peculiar ζa structure is demonstrated for the GaAs(100)-In surface. The beneficial effects of these surface structures regarding the crucial III-V oxide interface are demonstrated. Namely, it is found that it is possible to passivate the III-V surface by a careful atomic-scale engineering of the III-V surface prior to the gate-dielectric deposition. The thin (1×2)/(1×4)-Sn layer is found to catalyze the removal of harmful amorphous III-V oxides. Also, novel crystalline III-V-oxide structures are synthesized and it is shown that these structures improve the device characteristics. The finding of crystalline oxide structures is exploited by solving the atomic structure of InSb(100)(1×2) and elucidating the electronic structure of oxidized InSb(100) for the first time.

Occurrence of antibodies against Leptospira spp. In free-ranging wild canids from the Brazilian savanna

Abstract: The Brazilian savanna, also known as Cerrado, is one of the world's richest and most ecologically invaluable tropical savanna regions. There are few studies in Brazil about the diseases that affect the wild canids of this biome, which may be harmful to wildlife populations and public health. The aim of this study was to evaluate the occurrence of antibodies against Leptospira spp. in three Cerrado wild canids species using the microscopic agglutination test (MAT). Serum samples were tested from 19 crab-eating foxes (Cerdocyon thous), 14 maned wolves (Chrysocyon brachyurus), and seven hoary foxes (Lycalopex vetulus), all free-ranging animals found in the municipalities of Araguari and Uberlândia, Minas Gerais State, and Cumari, Goiás State, Brazil. Fourteen (35%) of these samples were seropositive. The most frequent serovars detected in the samples were Copenhageni and Hardjo, but reactions to the serovars Autumnalis, Grippotyphosa, Hebdomadis, Wolffi, and Icterohaemorrhagiae also occurred. Notwithstanding other reported results, this study is the first to report the presence of antibodies against Leptospira spp. in L. vetulus. The three species of wild canids examined may act as potential hosts for several serovars of leptospira in Brazil's savanna environment.

Indoor air quality at a waste incineration plant in Finland

Waste has been incinerated for energy utilization for more than a hundred years, but the harmful emissions emitted from the incineration plants did not begin to cause concern until the 1980s. Many plants were shutdown and the waste incineration plant in Kyläsaari Helsinki was one of them. In later years, new landfill regulations have increased the interest in waste incineration. During the last year, four new plants were taken into operation in Finland, Westenergy in Vaasa among them. The presence of dust has been observed indoors at Westenergy waste incineration plant. Dust is defined as particles with a diameter above 10 μm, while fine particles have a diameter smaller than 2.5 μm, ultrafine under 0.1 μm and nanoparticles under 0.05 μm. In recent years, the focus of particle health research has been changed to investigate smaller particles. Ultrafine particles have been found to be more detrimental to health than larger particles. Limit values regulating the concentrations of ultrafine particles have not been determined yet. The objective of this thesis was to investigate dust and particles present inside the Westenergy waste incineration facility. The task was to investigate the potential pollutant sources and to give recommendations of how to minimize the presence of dust and particles in the power plant. The total particle number concentrations and size distributions where measured at 15 points inside the plant with an Engine Exhaust Particle Sizer (EEPS) Spectrometer. The measured particles were mainly in the ultrafine size range. Dust was only visually investigated, since the main purpose was to follow the dust accumulation. The measurement points inside the incineration plant were chosen according to investigate exposure to visitors and workers. At some points probable leakage of emissions were investigated. The measurements were carried out during approximately one month in March–April 2013. The results of the measurements showed that elevated levels of dust and particles are present in the indoor air at the waste incineration plant. The cleanest air was found in the control room, warehouse and office. The most polluted air was near the sources that were investigated due to possible leakage and in the bottom ash hall. However, the concentrations were near measured background concentrations in European cities and no leakage could be detected. The high concentrations were assumed to be a result of a lot of dust and particles present on surfaces that had not been cleaned in a while. The main source of the dust and particles present inside the waste incineration plant was thought to be particles and dust from the outside air. Other activities in the area around the waste incineration facility are ground work activities, stone crushing and traffic, which probably are sources of particle formation. Filtration of the outside air prior entering the facility would probably save personnel and visitors from nuisance and save in cleaning and maintenance costs.

Pienten yksiköiden talousveden laatuvaatimukset ja - suositukset

Talousvesi sisältää paljon erilaisia yhdisteitä, joista osa on ihmiselle haitallisia, tällaisia yhdisteitä ovat muun muassa klooratut hiilivedyt. Haitallisten yhdisteiden määrän minimoimiseksi talousvedessä talousveden vieraille aineille on määrätty asetuksissa enimmäispitoisuuksia sekä – tiheyksiä. Näitä laatuvaatimuksia sekä – suosituksia noudattamalla talousvesi on käyttökelpoista. Talousvedellä ei tällöin ole haitallisia terveysvaikutuksia eikä se vahingoita vesilinjastoja. Kirjallisuusosassa selvitetään pienten yksiköiden talousveteen liittyvän sosiaali- ja terveysministeriön asetuksen sisältöä. Mitä asetus pitää sisällään, keitä asetus koskee ja miksi asetukseen kirjatut yhdisteet ja aineet ovat ihmiselle haitallisia sekä mitä terveysvaikutuksia kyseisillä aineilla on. Kokeellisessa osiossa analysoitiin kolmesta näytteestä osa sosiaali- ja terveysministeriön asettamista vaatimuksista. Pääsääntöisesti mitattiin epäorgaanisia aineita sekä ioneja. Mittaukset suoritettiin ionikromatografilla, liekki-atomiabsorptiospektrometrillä, TOC-analysaattorilla, COD-putkilla, pH-, johtokyky- sekä sameusmittarilla.

Productivity and Services – Safety Telephone Services for the Elderly

Previous research on productivity is often associated with manufacturing or uses manufacturing definitions of productivity. Marketing research on services has not been satisfied with the manufacturing definitions. No universal definition for service productivity exists. The lack of a universal definition highlights the complexity entailed in the concept of productivity. The objective of this study was to investigate service productivity in situations, where traditional ways are in some cases even not possible or are not enough. In one definition of the productivity of service organisations there is the efficiency of the organisation on the input side and on the output side the customers’ perceived quality or value-in-use. To learn about value-in-use, many methods have been developed. A common practice is to make customer opinion surveys in the form of customer questionnaires and interviews. However, customers cannot always be asked directly, for example, because of impaired cognitive abilities. Such cases include the elderly and children. Furthermore, customer opinion surveys are time consuming. In addition, customers do not always know what kind of services they would benefit from. For the empirical part of the study, a business area was identified where traditional ways of measuring value-in-use are difficult or in some cases even not possible. This business area is safety telephone services. These services are most often used by the elderly. The way to define value-in-use here was to assess how well the services offered met customer expectations. Comparing the services customers asked for and the services provided to them indicated whether customer expectations were met. This study showed that customers had their ideas concerning the contents of the services but many times the services provided did not meet these expectations. Organisational efficiency aspirations can decrease customers’ value-in-use. This study found a solution, in which increasing organisational efficiency would go hand-in-hand with increasing customers’ value-in-use; the result being that the organisations’ needs and the service users’ expectations were in line. Value creation for customers produced organisational efficiency and thus increased productivity. In this study, customer expectations were observed by means of wellness technology. With the help of modern technology, customer expectations can be followed quickly and easily and customers can co-create with the organisation. This type of an approach could be useful even in the development of other services for other ages and in different contexts. If a service organisation decreases the number of personnel and, at the same time, tries to offer services to the same or a larger clientele, customers easily notice the change, which is often negative. To avoid harmful decrease in value-in-use, limitations to the aspiration of efficiency should be implemented – one of such is that the organisation is required to meet certain quality standards defined by experts. The aim is to secure that, as a result of efficiency aspirations in the organisation, the quality of the service offerings does not diminish below mutually agreed standards. Traditionally, when productivity in services has been estimated, organisational efficiency has not been combined with both customer expectations and an expert assessment of quality. This study contributes with novel thinking entitled ‘Relationship Management of the Elderly’. This study handles productivity, expert defined quality and value-in-use in an organisational context, which is practically untouched in previous research studies.

Sorbent characterization for circulating fluidized bed scrubbers

Harmful sulfur dioxide (SO2) emissions from power plants have increasingly been restricted since the 1970’s. Circulating fluidized bed (CFB) scrubber is a dry flue gas desulfurization method of absorbing SO2 out of the flue gas with sorbent. In current commercial plants, the used sorbent is commercial or on-site hydrated calcium hydroxide. The CFB scrubber process is characterized by a close but adequate approach to the flue gas saturation temperature that is achieved by spraying water to the absorber followed by a particulate control device. Very high SO2 removal is achieved along with a dry byproduct that is continuously recirculated back to the absorber for enhanced sorbent utilization. The aim of this work is to develop a method that would characterize the reactivity of sorbents used in CFB scrubbers and to conclude how different process parameters and sorbent properties affect the sulfur absorption. The developed characterization method is based on a fixed bed of sorbent and inert silica sand, through which an SO2 containing gas mixture is led. The reaction occurs in the bed and the SO2 concentration in the outlet as a function of time, a breakthrough curve, is obtained from the analyzer. Reactivity of the sorbents are evaluated by the absorbed sulfur amount. Results suggest that out of process parameters, lower SO2 concentration, lower temperature and higher moisture content enhance the desulfurization. Between different sorbents, specific surface area seems to be the most significant parameter. Large surface area linearly leads to more efficient desulfurization. Overall, the solid conversion levels in the tests were very low creating uncertainty to the validity of the results. New desing is being planned to overcome the problems of the device.

Development of bean plants in soil contaminated with trifloxysulfuron-sodium after Stizolobium aterrimum and Canavalia ensiformis cultivation

Phytoremediation, the use of plants to decontaminate soils and water resources from organic pollutants such as herbicides, is economically and environmentally a promising technique applied in many areas, including agriculture. The objective of this work was to evaluate the development of bean plants cultivated in the field, in soil with different levels of trifloxysulfuron-sodium contamination, following cultivation of two green manure species, as well as to evaluate the possibility of recontamination of the area by such herbicide with the straw permanence on the soil. The experiment was carried out in Coimbra, MG, Brazil, on a sandy clayey Red - Yellow Argisol from March to November 2003. Four levels of soil contamination with trifloxysulfuron-sodium (0.00; 3.75; 7.50; and 15.00 g ha-1) were used as well as the following five types of cultivation prior to bean sowing in the area after herbicide application: black velvet beans (Stizolobium aterrimum) followed by removal of straw; S. aterrimum, followed by permanence of straw; jack bean (Canavalia ensiformis), followed by removal of straw; C. ensiformis followed by permanence of straw; and without prior cultivation, weed-free (weeded control). The leguminous plants were kept in the area for 65 days, cut close to the soil, and with its aerial part left or not on the surface of the experimental plot, depending on the treatment. Fifteen days after the species were cut, bean was sown in the area. At 45 days after emergence (DAE) of the bean plants, plant height and dry mass of the aerial part were evaluated. Grain productivity was determined during harvest. Height, dry matter of the aerial part and grain productivity of the bean plants, cultivated in an area previously contaminated with trifloxysulfuron-sodium at any of the levels tested, were higher with prior cultivation of S. aterrimum or C. ensiformis. At the lowest level of herbicide contamination, prior cultivation of C. ensiformis was found to be more efficient than that of S. aterrimum in mitigating the harmful effects of trifloxysulfuron-sodium on bean grain production. The permanence of the straw of the green manure species during the bean cycle did not harm the development of the plants or caused culture productivity losses, indicating that straw permanence in the area does not promote recontamination of the area.

Arseeni ja elohopea maaperässä ja vesistöissä

Maapallon väestön kasvaessa ja tarpeen makealle vedelle, ruualle ja viljelymaalle noustessa on tärkeää alkaa kiinnittää entistä tarkemmin huomiota vesistöjen ja maaperän saastumiseen myrkyllisillä raskasmetalleilla. Erityisesti elohopea ja arseeni, jotka jo nyt vaikuttavat heikentävästi miljoonien ihmisten elämään eri puolilla maapalloa, on syytä ottaa huolelliseen tarkkailuun. Raskasmetallien päästölähteet voidaan jakaa kahteen luokkaan, luonnollisiin ja ihmisperäisiin. Ihmisperäisiin päästölähteisiin voidaan vaikuttaa muun muassa teollisuutta ja liikennettä koskevalla lainsäädännöllä. Luonnollisiin päästölähteisiin vaikuttaminen on huomattavasti haastavampaa, mutta niiden haittaa ihmisille on mahdollista pienentää muun muassa parempien vedenpuhdistustekniikoiden avulla. Tämän työn kirjallisuusosassa tullaan esittelemään erityyppisiä luonnossa esiintyviä arseenin ja elohopean yhdisteitä, suurimpia arseenin ja elohopean päästölähteitä, sekä näiden raskasmetallien haitallisia terveysvaikutuksia. Kokeellisessa osassa tullaan keskittymään arseenin analysointiin nestemäisistä näytteistä. Näytteinä käytettiin tuntemattomilta kaatopaikoilta otettuja suotovesinäytteitä, sekä Pien-Saimaan pintavesinäytteitä. Analyyseihin on käytetty ICP-AES laitteistoa sekä kapillaarielektroforeesia.

Photosynthetic activity of cassava plants under weed competition

The objective of this work was to evaluate characteristics associated with the photosynthetic activity of cassava plants under weed competition. The trial was carried out under field conditions, and experimental units consisted of 150 dm³ fiberglass boxes containing red yellow Latosol, previously corrected and fertilized. Treatments consisted in the cultivation of cassava plants which were free of weed competition and associated with three weed species: Bidens pilosa, Commelina benghalensis or Brachiaria plantaginea. After manioc sprouting started, 15 days after being planted, weeds that had been sown when manioc was planted were thinned, there were then eight plants left per experimental unit in accordance with specified treatments: cassava free of competition, cassava competing with B. pilosa, cassava competing with C. benghalensis and cassava competing with B. plantaginea. Sixty days after crop emergence leaf internal CO2 concentration (Ci), leaf temperature at the time of evaluation (Tleaf) and photosynthetic rate (A) were evaluated, also the CO2 consumption rate (ΔC) of cassava plants was calculated. A correlation matrix between variables was also obtained. All characteristics associated with photosynthesis in cassava plants were influenced by weed species. Cassava was more affected by B. pilosa and B. plantaginea in which concerns its exposition to solar radiation and water, while C. benghalensis seems to mostly affect the composition of incident light on the culture, allowing cassava to anticipate imposition when competing, even before it reaches harmful levels.

School Bullies’ Quest for Power: Implications for Group Dynamics and Intervention

Bullying is characterized by an inequality of power between perpetrator and target. Findings that bullies can be highly popular have helped redefine the old conception of the maladjusted school bully into a powerful individual exerting influence on his peers from the top of the peer status hierarchy. Study I is a conceptual paper that explores the conditions under which a skillful, socially powerful bully can use the peer group as a means of aggression and suggests that low cohesion and low quality of friendships make groups easier to manipulate. School bullies’ high popularity should be a major obstacle for antibullying efforts, as bullies are unlikely to cease negative actions that are rewarding, and their powerful position could discourage bystanders from interfering. Using data from the Finnish program KiVa, Study II supported the hypothesis that antibullying interventions are less effective with popular bullies in comparison to their unpopular counterparts. In order to design interventions that can address the positive link between popularity and aggression, it is necessary to determine in which contexts bullies achieve higher status. Using an American sample, Study III examined the effects of five classroom features on the social status that peers accord to aggressive children, including classroom status hierarchy, academic level and grade level, controlling for classroom mean levels of aggression and ethnic distribution. Aggressive children were more popular and better liked in fifth grade relative to fourth grade and in classrooms of higher status hierarchy. Surprisingly, the natural emergence of status hierarchies in children’s peer groups has long been assumed to minimize aggression. Whether status hierarchies hinder or promote bullying is a controversial question in the peer relations’ literature. Study IV aimed at clarifying this debate by testing the effects of the degree of classroom status hierarchy on bullying. Higher hierarchy was concrrently associated with bullying and predictive of higher bullying six months later. As bullies’ quest for power is increasingly acknowledged, some researchers suggest teaching bullies to attain the elevated status they yearn for through prosocial acts. Study V cautions against such solutions by reviewing evidence that prosocial behaviors enacted with the intention of controlling others can be as harmful as aggression.