Estudo e desenvolvimento de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential substitute, since both belong to the same group of the periodic table and because of this have many similar physical and chemical properties. Niobium has several technologically important applications, and Brazil has the largest reserves, around 96%. There are including niobium in reserves of tantalite and columbite in Rio Grande do Norte. These electrolytic capacitors have high capacitance specifies, ie they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium powder supplied by EEL-USP was first characterized by XRD, SEM, XRF and laser particle size, to then be sieved into three particle size, 200, 400 e 635mesh. The powders were then compacted and sintered at 1350, 1450 and 1550°C using two sintering time 30 and 60min. Sintering is one of the most important parts of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. The sintered samples then underwent a process of anodic oxidation, which created a thin film of niobium pentóxido over the whole porous surface of the sample, this film is the dielectric capacitor. The oxidation process variables influence the performance of the film and therefore the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor, ESR, relative density, porosity and surface area. After the characterizations was made an annealing in air ate 260ºC for 60min. After this treatment were made again the electrical measurements. The particle size of powders and sintering affected the porosity and in turn the specific area of the samples. The larger de area of the capacitor, greater is the capacitance. The powder showed the highest capacitance was with the smallest particle size. Higher temperatures and times of sintering caused samples with smaller surface area, but on the other hand the cleaning surface impurities was higher for this cases. So a balance must be made between the gain that is achieved with the cleaning of impurities and the loss with the decreased in specific area. The best results were obtained for the temperature of 1450ºC/60min. The influence of annealing on the loss factor and ESR did not follow a well-defined pattern, because their values increased in some cases and decreased in others. The most interesting results due to heat treatment were with respect to capacitance, which showed an increase for all samples after treatment

Group analysis method for fission track thermochronology

A methodology to obtain ages and thermal histories of sets of apatite samples from localities with geologically compatible characteristics is described. A methodology exploring the fact that samples with similar geological characteristics should present the same thermal history is proposed. This approach can contribute for the obtainment of more conclusive results by analysing fewer samples than it is necessary when the samples are individually analysed. In order to determine the ages, we use the absolute neutron dosimetry through thin films of natural uranium along with lambda(f) = 8.46 x 10(-17) a(-1). As an example of application of the proposed methodology, we analyse samples collected in a Brazilian region, Sao Francisco Craton, which experienced low tectonic activity. (C) 2008 Elsevier Ltd. All rights reserved.

Hyperfine interaction in Zn-Al layered double hydroxides intercalated with conducting polymers

Organic-inorganic hybrid materials based on the assembly between inorganic 2D host structure and polymer have received considerable attention in the last few years. This emerging class of materials presents several applications according to their structural and functional properties. Particularly, among others, layered double hydroxides (LDHs) provide the opportunity of preparing new organically modified 2D nanocomposites. Pyrrole carboxylic acid derivatives, namely 4-(lH-pyrrol-1-yl)benzoate, 3-(pyrrol-i-yl)-propanoate,7-(pyrrol-1-yl)-heptanoate, and aniline carboxylic acid derivative, namely 3-aminobenzoic acid, have been intercalated in LDHs of intralamellar composition Zn2Al(OH)(6). The LDHs were synthesized by the co-precipitation method at constant pH followed by hydrothermal treatment for 72 h. The materials were characterized by powder X-ray diffraction patterns (PXRD), transmission electron microscopy (TEM) thermogravimetric analysis (TGA), and electron spin resonance (ESR). The basal spacing found by the PXRD technique gives evidence of the formation of bilayers of the intercalated anions. ESR spectra present a typical signal with a superhyperfine structure with 6 + 1 lines (g = 2.005 +/- 0.0004), which is assigned to the interaction between a carboxylate radical from the guest molecules and a nearby aluminium nucleus (I = 5/2) from the host structure. Additionally, the ESR data suggest that the monomers are connected to each other in limited number after thermal treatment. (c) 2007 Elsevier Ltd. All rights reserved.

Electron spin resonance of Gd3+ in the antiferromagnetic heavy fermion CeIn3 and its reference compound LaIn3

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Optical Behavior of Conjugated Pt-Containing Polymetallaynes Exposed to Gamma-Ray Radiation Doses

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Adsorption of Cu(II) and Co(II) complexes on a silica gel surface chemically modified with 2-mercaptoimidazole

The isotherms of adsorption of MeX2 (Me = Cu2+, Co2+; X = Cl-, Br-, ClO4-) by silica gel chemically modified with 2-mercaptoimidazole (SiMI) were studied in acetone and ethanol solutions, at 25 degrees C. Covalently attached 2-mercaptoimidazole molecule to silica gel surface adsorbs MeX2 from solvent by forming a surface complex. The metal is bonded to the surface through the nitrogen atom of attached 2-mercaptoimidazole. At low loading, the electronic and ESR spectral parameters indicated that the Cu2+ complexes are in a distorted-tetragonal symmetry field. The d-d electronic transition spectra showed that for Cu(ClO4)(2) complex, the peak of absorption did not change for any degree of metal loading and for Cl- and Br- complexes, the peak maxima shifted to higher energy with lower metal loading. The CoX2(X = Cl-, Br-, ClO4-) analogues possess a distorted-tetrahedral field.

Nanoparticles of octakis [3-(3-amino-1,2,4-triazole)propyl] octasilsesquioxane as ligands for Cu(II), Ni(II), Cd(II), Zn(II), and Fe(III) in aqueous solution

Nanoparticles of octakis[3-(3-amino-1,2,4-triazole)propyl]octasilsesquioxane (ATZ-SSQ) were tested as ligands, for transition-metal ions in aqueous solution with a special attention to sorption isotherms, ligand-metal interaction, and determination of metal ions in natural waters. The adsorption potential of the material ATZ-SSQ was compared with related [3(3-amino-1,2,4-triazole)propyl]silica gel (ATZ-SG). The adsorption was performed using a batchwise process and both organofunctionalized surfaces showed the ability to adsorb the metal ions from aqueous solution. The Langmuir model was used to simulate the sorption isotherms. The results suggest that the sorption of these metals on ATZ-SSQ and ATZ-SG occurs mainly by surface complexation. The equilibrium condition is reached at time lower than 3 min for ATZ-SSQ, while for ATZ-SG is only reached at time of 25 min. The maximum metal ion uptake values for ATZ-SSQ were higher than the corresponding values achieved with the ATZ-SG. In order to obtain more information on the ligand-metal interaction of the complexes on the surface of the ATZ-SSQ nanomaterial, ESR study with various degrees of copper loadings was carried out. The ATZ-SSQ was tested for the determination (in flow using a column technique) of the metal ions present in natural waters. (C) 2007 Elsevier B.V. All rights reserved.

Structure of copper(II) complexes adsorbed on functionalized polyhedral oligomeric silsesquioxane

The 3-amino-1,2,4-triazole-modified silsesquioxane nanoplatforms have been prepared and characterized. The silsesquioxane nanocages readily react with CuX(2) in aqueous solution to form copper complex-substituted silsesquioxanes. Adsorption isotherms of CuX(2) from aqueous solution were studied at 25 degrees C. The electronic and ESR spectral parameters indicated that the copper ion is in a distorted-tetragonal symmetry field. (C) 2007 Elsevier B.V. All rights reserved.

Adsorption of transition-metal ions in ethanol solution by a nanomaterial based on modified silsesquioxane

The material octakis[3-(3-amino- 1,2,4-triazole)propyl]octasilsesquioxane (ATZ-SSQ) was synthesized and its potential was assessed for Cu(II), Ni(II), Co(II), Zn(II) and Fe(III) from their ethanol solutions and compared with related 3-amino-1,2,4-triazole-propyl modified silica gel (ATZ-SG). The adsorption was performed using a batchwise process and both organofunctionalized surfaces showed the ability to adsorb the metal ions from ethanol solution. The Langmuir model allowed to describe the sorption of the metal ions on ATZ-SSQ and ATTZ-SG in a satisfactory way. The equilibrium is reached very quickly Q min) for ATZ-SSQ, indicating that the adsorption sites are well exposed. The maximum metal ion uptake values for Cu(II), Co(II), Zn(II), Ni(II) and Fe(III) were 0.86, 0.09, 0.19, 0.09 and 0.10 mmol g(-1), respectively, for the ATZ-SSQ, which were higher than the corresponding values 0.21, 0.04, 0.14, 0.05 and 0.07 mmol g(-1) achieved with the ATZ-SG. In order to obtain more information on the metal-ligand interaction of the complexes on the surface of the ATZ-SSQ, Cu(II) was used as a probe to determine the arrangements of the ligands around the central metal ion by electron spin resonance (ESR). The ATZ-SSQ was used for the separation and determination (in flow using a column technique) of the metal ions present in commercial ethanol. (c) 2008 Elsevier B.V. All rights reserved.

Dosimetric properties of UV irradiated calcium co-doped borate glass-ceramic

The thermoluminescence (TL) response of Dy and Li doped 20CaB(4)O(7)-80CaB(2)O(4) (Wt%) glass-ceramic irradiated with ultraviolet (UV) radiation was studied. In order to act as TL activator ions, the Dy and Li ions were included in the matrix during the melting process to increase its TL efficiency. A single crystalline CaB2O4 phase was present in the glass-ceramic as determined by X-ray diffraction (XRD). The glass-ceramic 20CaB(4)O(7)-80CaB(2)O(4):Dy,Li wt% (named 20CBO7:Dy,Li) is a newly prepared TL material. Its thermoluminescent dosimetric characteristics have shown a linear response under UV radiation exposure and a good TL signal reproducibility, thus proving to be a promising material for using as an ultraviolet radiation dosimeter. (C) 2007 Elsevier B.V. All rights reserved.

Controle de qualidade e dosimetria em equipamentos de tomografia computadorizada

OBJETIVO: Avaliação de condições dos equipamentos e dosimetria em setores de tomografia computadorizada utilizando protocolos de cabeça, abdome e coluna lombar em pacientes adultos (em três equipamentos distintos) e pediátricos com até um ano e meio de vida (em um dos equipamentos avaliados). MATERIAIS E MÉTODOS: Foram estimados o índice de dose em tomografia computadorizada e a dose média em cortes múltiplos, em exames com pacientes adultos, em três distintos equipamentos. Ainda foram estimadas as doses na superfície de entrada e as doses absorvidas em exame de cabeça para pacientes adultos e pediátricos em um dos equipamentos avaliados. RESULTADOS: Foram realizados testes de controle de qualidade, mecânicos, demonstrando que os equipamentos satisfazem as especificações de uso estabelecidas pelas normas vigentes. Os resultados da dosimetria mostraram que valores de dose média em cortes múltiplos excederam em até 109,0% os valores de níveis de referência, apresentando consideráveis variações entre os equipamentos avaliados neste estudo. As doses absorvidas obtidas com protocolos pediátricos são inferiores aos de pacientes adultos, apresentando redução de até 51,0% na tireoide. CONCLUSÃO: Neste estudo foram avaliadas as condições de operação de três equipamentos tomográficos, estabelecendo quais parâmetros devem ser trabalhados para a implantação de um programa de controle de qualidade nas instituições onde esta pesquisa foi desenvolvida.

A complete dosimetric characterization of two Sr-90-Y-90 dermatologic applicators

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Pulmonary tuberculosis: Hematology, serum biochemistry and the relation with the disease duration

The aim of the present study was to analyze the relationship between hematological and biochemical parameters and tuberculosis process activity time according to clinical complaint duration. It was a retrospective study analyzing medical records from 80 pulmonary tuberculosis patients at Botucatu Medical School University Hospital ( Botucatu, São Paulo State, Brazil), who were divided into 2 groups according to clinical complaint duration: Group 1 ( G1) - up to three months; Group 2 ( G2) - over three months. Parameters included: age, gender, bacilloscopy, erythrocyte sedimentation rate ( ESR), platelet count, alpha1-globulin, alpha2-globulin, gamma globulin, mucoprotein, alpha1-acid glycoprotein values, and the presence of risk factors such as smoking, alcoholism, drug addiction, sexual promiscuity, contact with tuberculosis carriers, and previous treatment. Groups were compared by calculating t and p, and Chi-square (X-2) and p. Comparisons revealed a tendency towards smoking with a higher frequency of smokers in G1 ( 0.05< p< 0.10). G1 also tended to present greater platelet values than G2 ( 0.05< p< 0.10) and presented significantly higher ESR values than G2 ( p< 0.05). Other factors did not show any significantly different behavior between groups ( p> 0.05). A correlation was found between ESR, platelet count, smoking and less than three months clinical duration.

Cytokines and acute-phase serum proteins as markers of inflammatory regression during pulmonary tuberculosis treatment

Tuberculosis is still increasing and was declared a worldwide sanitary emergency by the World Health Organization (WHO) in 1995. Its control is difficult due to long treatment duration and lack of markers of treatment success or failure. Cytokines such as IFN-gamma and TNF-alpha, a central factor in immune response against Mycobacterium tuberculosis, are responsible for the interaction between T lymphocytes and the infected macrophage and are also produced during this interaction. As proinflammatory cytokines have a close relationship with mycobacteria clearance, in fact even preceding it, they could be used as markers for inflammatory activity and response to treatment. Proinflammatory cytokines act in the liver and stimulate a strong local and systemic acute-phase response as a result of homeostatic and physiological responses also induced by them. Acute-phase proteins produced by cytokine activity are useful diagnostic markers that could also be used to monitor treatment response as they can be serially quantified. The objective of this study was to evaluate IFN-gamma, TNF-alpha, IL-10 and TGF-beta production in supernatant of peripheral blood mononuclear cell (PBMC) and monocyte (MO) cultures, as well as serum acute-phase response through total protein, albumin, globulin, C-reactive protein (CRP), alpha-1-acid glycoprotein (AGP), and erythrocyte sedimentation rate (ESR) as regression markers of inflammatory response during pulmonary tuberculosis treatment. Twenty blood donors (G1) from the Blood Bank at Botucatu School of Medicine's University Hospital (BSM-UH) were evaluated once and 28 pulmonary tuberculosis patients (G2): 13 from BSM-UH and 15 from the Bauru State Health Secretariat. Patients were evaluated at three moments of treatment: before (M1), at three months (M2), and at the end (M3). Cytokines were determined in 20ml of peripheral blood (ELISA), with or without activation: lipopolysaccharide (LPS) for MO culture and phytohemagglutinin (PHA) for PBMC culture. Acute-phase protein behavior in G2 throughout treatment was: Globulins: M1> M2, M1> M3 (rho < 0.001); CRP: M1> M2> M3 (.< 0.001); AGP for men: M1> M2, M1> M3 (rho < 0.001); ESR for men: M1> M2, M1> M3 (rho < 0.0016) and for women: M1> M2 (.< 0.025). Comparison between cytokine levels found in supernatant of MO and PBMC cultures, with and without stimulus, in G1 and G2 during treatment showed: TNF-alpha (with/ without LPS) at M1: G2> G1; at M2: G2> G1 (rho < 0.001); (without LPS) at M3: G2> G1 (rho < 0.001), (with LPS) at M3: G2> G1 (rho < 0.028); IFN-. (with and without PHA) at M1: G2> G1; at M2: G2> G1 (rho < 0.001); IL-10 (with and without LPS) at M1: G2> G1; at M2: G2> G1; at M3: G2> G1 (rho < 0.001); TGF-beta (with and without LPS) at M1: G2> G1; at M2: G2> G1 (rho < 0.001), (without LPS) at M3: G2> G1 (rho < 0.001). In G2, all cytokines in supernatant of MO and PBMC cultures, with and without stimulus, showed: M1> M2> M3 (rho < 0.01). Levels of globulins, CRP, AGP, and ESR in patients with pulmonary tuberculosis before treatment (M1) were significantly higher than reference values, suggesting their use as diagnostic markers and indicators of treatment. The CRP decreasing values along treatment could be taken as a marker of the regression of inflammatory process and of response to treatment in patients with pulmonary tuberculosis.Regarding cytokines, there was significant increase in TNF-alpha, IFN-gamma, IL-10, and TGF-alpha levels before and at three months treatment, with and without stimulus; in TNF-a and IL-10 lvels, with and without stimulus, as well as in TGF-alpha levels without stimulus at six months. Patients had higher levels of all studied cytokines than controls before treatment, and these values decreased along treatment. In this study, pulmonary tuberculosis patients showed a Th0 cytokine profile before treatment, with the production of both Th1 (IFN-gamma) and Th2 (IL-10) cytokines, in addition to TNF-alpha inflammatory and TGF-alpha regulatory and fibrosis-inducer cytokines. At the end of treatment, all had evolved to Th2 profile, probably in an attempt to reduce the harmful effects of the proinflammatory activity of the Th1 cytokine profile and of the still above-normal levels of TNF-alpha. The high levels of TGF-alpha, also found in these patients, are related to its important role in the extracellular matrix deposition and fibrosis induction that characterize tuberculosis healing process. IFN-gamma was the only cytokine reaching normal levels at the end of treatment, which suggests its use as a marker of response to treatment.

Citocinas e proteínas de fase aguda do soro como marcadores de regressão da resposta inflamatória ao tratamento da tuberculose pulmonar

OBJETIVO: Analisar o padrão de citocinas pró- e antiinflamatórias e da resposta de fase aguda (RFA) como marcadores de resposta ao tratamento da tuberculose pulmonar. MÉTODOS: Determinação dos níveis de interferon-gama (IFN-γ), tumor necrosis factor-alpha (TNF-α, fator de necrose tumoral-alfa), interleucina-10 (IL-10) e transforming growth factor-beta (TGF-β, fator transformador de crescimento-beta), pelo método ELISA, em sobrenadante de cultura de células mononucleares do sangue periférico e monócitos, assim como dos níveis de proteínas totais, albumina, globulinas, alfa-1-glicoproteína ácida (AGA), proteína C reativa (PCR) e velocidade de hemossedimentação (VHS) em 28 doentes com tuberculose pulmonar, em três tempos: antes (T0), aos três meses (T3) e aos seis meses (T6) de tratamento, em relação aos controles saudáveis, em um único tempo. RESULTADOS: Os pacientes apresentaram valores maiores de citocinas e RFA que os controles em T0, com diminuição em T3 e diminuição (TNF-α, IL-10, TGF-β, AGA e VHS) ou normalização (IFN-γ e PCR) em T6. CONCLUSÕES: PCR, AGA e VHS são possíveis marcadores para auxiliar no diagnóstico de tuberculose pulmonar e na indicação de tratamento de indivíduos com baciloscopia negativa; PCR (T0 > T3 > T6 = referência) pode também ser marcador de resposta ao tratamento. Antes do tratamento, o perfil Th0 (IFN-γ, IL-10, TNF-α e TGF-β), indutor de e protetor contra inflamação, prevaleceu nos pacientes; em T6, prevaleceu o perfil Th2 (IL-10, TNF-α e TGF-β), protetor contra efeito nocivo pró-inflamatório do TNF-α ainda presente. O comportamento do IFN-γ (T0 > T3 > T6 = controle) sugere sua utilização como marcador de resposta ao tratamento.