A pseudo-dynamical systems approach to a class of inverse problems in engineering

A pseudo-dynamical approach for a class of inverse problems involving static measurements is proposed and explored. Following linearization of the minimizing functional associated with the underlying optimization problem, the new strategy results in a system of linearized ordinary differential equations (ODEs) whose steady-state solutions yield the desired reconstruction. We consider some explicit and implicit schemes for integrating the ODEs and thus establish a deterministic reconstruction strategy without an explicit use of regularization. A stochastic reconstruction strategy is then developed making use of an ensemble Kalman filter wherein these ODEs serve as the measurement model. Finally, we assess the numerical efficacy of the developed tools against a few linear and nonlinear inverse problems of engineering interest.

Arterial luminal curvature and fibrous-cap thickness affect critical stress conditions within atherosclerotic plaque: An in vivo MRI-based 2D finite-element study

High mechanical stress in atherosclerotic plaques at vulnerable sites, called critical stress, contributes to plaque rupture. The site of minimum fibrous cap (FC) thickness (FCMIN) and plaque shoulder are well-documented vulnerable sites. The inherent weakness of the FC material at the thinnest point increases the stress, making it vulnerable, and it is the big curvature of the lumen contour over FC which may result in increased plaque stress. We aimed to assess critical stresses at FCMIN and the maximum lumen curvature over FC (LCMAX) and quantify the difference to see which vulnerable site had the highest critical stress and was, therefore, at highest risk of rupture. One hundred patients underwent high resolution carotid magnetic resonance (MR) imaging. We used 352 MR slices with delineated atherosclerotic components for the simulation study. Stresses at all the integral nodes along the lumen surface were calculated using the finite-element method. FCMIN and LCMAX were identified, and critical stresses at these sites were assessed and compared. Critical stress at FC MIN was significantly lower than that at LCMAX (median: 121.55 kPa; inter quartile range (IQR) = [60.70-180.32] kPa vs. 150.80 kPa; IQR = [91.39-235.75] kPa, p < 0.0001). If critical stress at FCMIN was only used, then the stress condition of 238 of 352 MR slices would be underestimated, while if the critical stress at LCMAX only was used, then 112 out of 352 would be underestimated. Stress analysis at FCMIN and LCMAX should be used for a refined mechanical risk assessment of atherosclerotic plaques, since material failure at either site may result in rupture.

Critical Reappraisal Of Plasticity Index Of Soils

A fundamental approach, based on Gouy-Chapman theory of double layer, has been provided to micromechanistically interpret the plasticity index of soils and their relationship with liquid limit. The relationships between plasticity index and liquid limit, developed earlier, through statistical approaches and critical state concepts, have been reexamined. The statistical analysis of extensive published data has resulted in the relationship, IP = 0.74 (wL - 8). On comparison with other relationships in vogue the proposed equation has been found to give better agreement. From the reappraisal of critical state approaches consistent with the micromechanistic interpretation, the possible range of parameters have been computed and compared with those obtained by statistical means to enhance the credibility of the proposed relationship.

How critical is fibrous cap thickness to carotid plaque stability? A flow-plaque interaction model

Background and Purpose Acute cerebral ischemic events are associated with rupture of vulnerable carotid atheroma and subsequent thrombosis. Factors such as luminal stenosis and fibrous cap thickness have been thought to be important risk factors for plaque rupture. We used a flow-structure interaction model to simulate the interaction between blood flow and atheromatous plaque to evaluate the effect of the degree of luminal stenosis and fibrous cap thickness on plaque vulnerability. Methods A coupled nonlinear time-dependent model with a flow-plaque interaction simulation was used to perform flow and stress/strain analysis in a stenotic carotid artery model. The stress distribution within the plaque and the flow conditions within the vessel were calculated for every case when varying the fibrous cap thickness from 0.1 to 2 mm and the degree of luminal stenosis from 10% to 95%. A rupture stress of 300 kPa was chosen to indicate a high risk of plaque rupture. A 1-sample t test was used to compare plaque stresses with the rupture stress. Results High stress concentrations were found in the plaques in arteries with >70% degree of stenosis. Plaque stresses in arteries with 30% to 70% stenosis increased exponentially as fibrous cap thickness decreased. A decrease of fibrous cap thickness from 0.4 to 0.2 mm resulted in an increase of plaque stress from 141 to 409 kPa in a 40% degree stenotic artery. Conclusions There is an increase in plaque stress in arteries with a thin fibrous cap. The presence of a moderate carotid stenosis (30% to 70%) with a thin fibrous cap indicates a high risk for plaque rupture. Patients in the future may be risk stratified by measuring both fibrous cap thickness and luminal stenosis.

Advancing practice in critical care: A model of knowledge integration

It could be argued that advancing practice in critical care has been superseded by the advanced practice agenda. Some would suggest that advancing practice is focused on the core attributes of an individuals practice progressing onto advanced practice status. However, advancing practice is more of a process than identifiable skills and as such is often negated when viewing the development of practitioners to the advanced practice level. For example practice development initiatives can be seen as advancing practice for the masses which ensures that practitioners are following the same level of practice. The question here is; are they developing individually.

Influence of Elastic-Constants on Mode-I Stress-Intensity Factors in 3-Dimensional Crack Problems

Plates with V-through edge notches subjected to pure bending and specimens with rectangular edge-through-notches subjected to combined bending and axial pull were investigated (under live-load and stress-frozen conditions) in a completely nondestructive manner using scattered-light photoelasticity. Stress-intensity factors (SIFs) were evaluated by analysing the singular stress distributions near crack-tips. Improved methods are suggested for the evaluation of SIFs. The thickness-wise variation of SIFs is also obtained in the investigation. The results obtained are compared with the available theoretical solutions.

Critical Cation Balance In B-]Z Transition - Role Of Li+

The sodium salt of poly(dG-dC) is known to exhibit a B + Z transition in the presence of various cations and 60% alcohol. We here show that the lithium salt of poly(dG-dC) does not undergo B 4 Z transition in the presence of 60% alcohol since Li’ with its large hydration shell cannot stabilize the Z-form. On the other hand, high concentrations of Mg2* or micromolar concentrations of the cobalt hexamine complex which are known to stabilize the Z-form can compete with Li+ for charge neutraIization and hence bring about a B--t Z transition in the same polymer. From the model building studies the mode of action of the cobalt-hexamine complex in stabilizing the Z-form is postulated.

Process Analytical Technology Approach on Fluid Bed Granulation and Drying : Identifying Critical Relationships and Constructing the Design Space

Fluid bed granulation is a key pharmaceutical process which improves many of the powder properties for tablet compression. Dry mixing, wetting and drying phases are included in the fluid bed granulation process. Granules of high quality can be obtained by understanding and controlling the critical process parameters by timely measurements. Physical process measurements and particle size data of a fluid bed granulator that are analysed in an integrated manner are included in process analytical technologies (PAT). Recent regulatory guidelines strongly encourage the pharmaceutical industry to apply scientific and risk management approaches to the development of a product and its manufacturing process. The aim of this study was to utilise PAT tools to increase the process understanding of fluid bed granulation and drying. Inlet air humidity levels and granulation liquid feed affect powder moisture during fluid bed granulation. Moisture influences on many process, granule and tablet qualities. The approach in this thesis was to identify sources of variation that are mainly related to moisture. The aim was to determine correlations and relationships, and utilise the PAT and design space concepts for the fluid bed granulation and drying. Monitoring the material behaviour in a fluidised bed has traditionally relied on the observational ability and experience of an operator. There has been a lack of good criteria for characterising material behaviour during spraying and drying phases, even though the entire performance of a process and end product quality are dependent on it. The granules were produced in an instrumented bench-scale Glatt WSG5 fluid bed granulator. The effect of inlet air humidity and granulation liquid feed on the temperature measurements at different locations of a fluid bed granulator system were determined. This revealed dynamic changes in the measurements and enabled finding the most optimal sites for process control. The moisture originating from the granulation liquid and inlet air affected the temperature of the mass and pressure difference over granules. Moreover, the effects of inlet air humidity and granulation liquid feed rate on granule size were evaluated and compensatory techniques used to optimize particle size. Various end-point indication techniques of drying were compared. The ∆T method, which is based on thermodynamic principles, eliminated the effects of humidity variations and resulted in the most precise estimation of the drying end-point. The influence of fluidisation behaviour on drying end-point detection was determined. The feasibility of the ∆T method and thus the similarities of end-point moisture contents were found to be dependent on the variation in fluidisation between manufacturing batches. A novel parameter that describes behaviour of material in a fluid bed was developed. Flow rate of the process air and turbine fan speed were used to calculate this parameter and it was compared to the fluidisation behaviour and the particle size results. The design space process trajectories for smooth fluidisation based on the fluidisation parameters were determined. With this design space it is possible to avoid excessive fluidisation and improper fluidisation and bed collapse. Furthermore, various process phenomena and failure modes were observed with the in-line particle size analyser. Both rapid increase and a decrease in granule size could be monitored in a timely manner. The fluidisation parameter and the pressure difference over filters were also discovered to express particle size when the granules had been formed. The various physical parameters evaluated in this thesis give valuable information of fluid bed process performance and increase the process understanding.

Critical-Behavior Of The Diameters Of Liquid-Liquid Coexistence Curves

We have analyzed the diameters of the liquid–liquid coexistence curves of several binary liquid mixtures in search of the critical anomaly predicted by current theories. We find that while the data are consistent with the predicted functional form, the evidence for such an anomaly is not compelling.

Critical remarks on "On the compensation effect"

A critical assessment of a published paper (by Agrawal) is presented. The procedure proposed and used by Agrawal to distinguish a false compensation effect from a true one is shown not to be correct.

An E-Convergence Method For The Evaluation Of Critical Parameters

A simple cconversence technique is applied to obtain accurate estimates of critical temperatures and critical it\ponmts of a few two- and threpdiniensional king models. When applied to the virial series for hard spheres and hard discs, this method predicts a divergence of the equation-of-state at the density of closest packing.

Expansivity of liquid (cyclohexane + acetic anhydride) near its critical solution point

A simple volume dilatometer is described for the precise measurements of volume changes as a function of temperature in liquid mixtures. The expansivity of (cyclohexane + acetic anhydride) in the critical region was measured. The critical solution temperature Tc was approached to within 9 mK. For T > (Tc + 0.3 K), the results results follow both a logarithmic and a power-law behaviour with an exponent ≈ 1/8. But for T < (Tc + 0.3 K), the results seem to be affected possibly by gravity or temperature gradients. In this region, the expected expansivity anomaly is rounded off to a cusp. The expansivity shows a reduced anomaly for off-critical compositions. A discussion of the local extremum and a correlation between negative expansivity and the resistivity anomaly are also given.

Ant Colony Optimization Algorithms for Shortest Path Problems

We propose four variants of recently proposed multi-timescale algorithm in [1] for ant colony optimization and study their application on a multi-stage shortest path problem. We study the performance of the various algorithms in this framework. We observe, that one of the variants consistently outperforms the algorithm [1].

Problems of Proto-Slavic Historical Nominal Morphology : On the Basis of Old Church Slavic

In this study I offer a diachronic solution for a number of difficult inflectional endings in Old Church Slavic nominal declensions. In this context I address the perhaps most disputed and the most important question of the Slavic nominal inflectional morphology: whether there was in Proto-Slavic an Auslautgesetz (ALG), a law of final syllables, that narrowed the Proto-Indo-European vowel */o/ to */u/ in closed word-final syllables. In addition, the work contains an exhaustive morphological classification of the nouns and adjectives that occur in canonical Old Church Slavic. I argue that Proto-Indo-European */o/ became Proto-Slavic */u/ before word-final */s/ and */N/. This conclusion is based on the impossibility of finding credible analogical (as opposed to phonological) explanations for the forms supporting the ALG hypothesis, and on the survival of the neuter gender in Slavic. It is not likely that the */o/-stem nominative singular ending */-u/ was borrowed from the accusative singular, because the latter would have been the only paradigmatic form with the stem vowel */-u-/. It is equally unlikely that the ending */-u/ was borrowed from the */u/-stems, because the latter constituted a moribund class. The usually stated motivation for such an analogical borrowing, i.e. a need to prevent the merger of */o/-stem masculines with neuters of the same class, is not tenable. Extra-Slavic, as well as intra-Slavic evidence suggests that phonologically-triggered mergers between two semantically opaque genders do not tend to be prevented, but rather that such mergers lead to the loss of the gender opposition in question. On the other hand, if */-os/ had not become */-us/, most nouns and, most importantly, all adjectives and pronouns would have lost the formal distinction between masculines and neuters. This would have necessarily resulted in the loss of the neuter gender. A new explanation is given for the most apparent piece of evidence against the ALG hypothesis, the nominative-accusative singular of the */es/-stem neuters, e.g. nebo 'sky'. I argue that it arose in late Proto-Slavic dialects, replacing regular nebe, under the influence of the */o/- and */yo/-stems where a correlation had emerged between a hard root-final consonant and the termination -o, on the one hand, and a soft root-final consonant and the termination -e, on the other.

Análisis de la preposición hacia y establecimiento de sus equivalentes en finés

Title of the Master's thesis: Análisis de la preposición hacia y establecimiento de sus equivalentes en finés (trans. Analysis of the Spanish preposition hacia and the finding of its equivalents in Finnish) Abstracts: The aim of this Master thesis is to provide a detailed analysis of the Spanish preposition hacia from a cognitive perspective and to establish its equivalents in Finnish language. In this sense, my purpose is to demonstrate the suitability of both cognitive perspectives and Contrastive Linguistics for semantic analysis. This thesis is divided into five chapters. The first chapter includes a presentation and a critical review of the monolingual lexical processing and semantic analysis of the Spanish preposition hacia in major reference works. Through this chapter it is possible to see both the inadequacies and omissions that are present in all the given definitions. In this sense, this chapter shows that these problems are not but the upper stage of an ontological (and therefore methodological) problem in the treatment of prepositions. The second chapter covers the presentation of the methodological and theoretical perspective adopted for this thesis for the monolingual analysis and definition of the Spanish preposition hacia, following mainly the guidelines established by G. Lakoff (1987) and R. Langacker (2008) in his Cognitive grammar. Taken together, and within the same paradigm, recent analytical and methodological contributions are discussed critically for the treatment of polysemy in language (cf. Tyler ja Evans 2003). In the third chapter, and in accordance with the requirements regarding the use of empirical data from corpora, is my aim to set out a monolingual original analysis of the Spanish preposition hacia in observance of the principles and the methodology spelled out in the second chapter. The main objective of this chapter is to build a full fledged semantic representation of the polysemy of this preposition in order to understand and articulate its meanings with Finnish language (and other possible languages). The fourth chapter, in accordance with the results of chapter 3, examines and describes and establishes the corresponding equivalents in Finnish for this preposition. The results obtained in this chapter are also contrasted with the current bilingual lexicographical definitions found in the most important dictionaries and grammars. Finally, in the fifth chapter of this thesis, the results of this work are discussed critically. In this way, some observations are given regarding both the ontological and theoretical assumptions as well regarding the methodological perspective adopted. I also present some notes for the construction of a general methodology for the semantic analysis of Spanish prepositions to be carried out in further investigations. El objetivo de este trabajo, que caracterizamos como una tarea de carácter comparativo-analítico, es brindar un análisis detallado de la preposición castellana hacia desde una perspectiva cognitiva en tanto y a través del establecimiento de sus equivalentes en finés. Se procura, de esta forma, demostrar la adecuación de una perspectiva cognitiva tanto para el examen como para el establecimiento y articulación de la serie de equivalentes que una partícula, en nuestro caso una preposición, encuentra en otra lengua. De esta forma, y frente a definiciones canónicas que advierten sobre la imposibilidad de una caracterización acabada del conjunto de usos de una preposición, se observa como posible, a través de la aplicación de una metodología teórica-analítica adecuada, la construcción de una definición viable tanto en un nivel jerárquico como descriptivo. La presente tesis se encuentra dividida en cinco capítulos. El primer capítulo comprende una exposición y revisión critica del tratamiento monolingüe lexicográfico y analítico que la preposición hacia ha recibido en las principales obras de referencia, donde se observa que las inadecuaciones y omisiones presentes en la totalidad de las definiciones analizadas representan tan sólo el estadio superior de una problemática de carácter ontológico y, por tanto, metodológico, en el tratamiento de las preposiciones. El capítulo segundo comprende la presentación de la perspectiva teórica metodológica adoptada en esta tesis para el análisis y definición monolingüe de la preposición hacia, teniendo por líneas directrices las propuestas realizadas por G. Lakoff , así como a los fundamentos establecidos por R. Langacker en su propuesta cognitiva para una nueva gramática. En forma conjunta y complementaria, y dentro del mismo paradigma, empleamos, discutimos críticamente y desarrollamos diferentes aportes analítico-metodológicos para el tratamiento de la polisemia en unidades lingüísticas locativas. En el capítulo tercero, y en acuerdo con las exigencias respecto a la utilización de datos empíricos obtenidos a partir de corpus textuales, se expone un análisis original monolingüe de la preposición hacia en observancia de los principios y la metodología explicitada en el capítulo segundo, teniendo por principal objetivo la construcción de una representación semántica de la polisemia de la preposición que comprenda y articule los sentidos prototípicos para ésta especificados. El capítulo cuarto, y en acuerdo con los resultados de nuestro análisis monolingual de la preposición, se examinan, describen y establecen los equivalentes correspondientes en finés para hacia; asimismo, se contrastan en este capítulo los resultados obtenidos con las definiciones lexicográficas bilingües vigentes. Se recogen en el último y quinto capítulo de esta tesis algunas observaciones tanto respecto a los postulados ontológicos y teórico-metodológicos de la perspectiva adoptada, así como algunas notas para la construcción de una metodología general para el análisis semántico preposicional.