Estudo e desenvolvimento de um capacitor eletrolítico de nióbio

It seeks to find an alternative to the current tantalum electrolytic capacitors in the market due to its high cost. Niobium is a potential substitute, since both belong to the same group of the periodic table and because of this have many similar physical and chemical properties. Niobium has several technologically important applications, and Brazil has the largest reserves, around 96%. There are including niobium in reserves of tantalite and columbite in Rio Grande do Norte. These electrolytic capacitors have high capacitance specifies, ie they can store high energy in small volumes compared to other types of capacitors. This is the main attraction of this type of capacitor because is growing demand in the production of capacitors with capacitance specifies increasingly high, this because of the miniaturization of various devices such as GPS devices, televisions, computers, phones and many others. The production route of the capacitor was made by powder metallurgy. The initial niobium powder supplied by EEL-USP was first characterized by XRD, SEM, XRF and laser particle size, to then be sieved into three particle size, 200, 400 e 635mesh. The powders were then compacted and sintered at 1350, 1450 and 1550°C using two sintering time 30 and 60min. Sintering is one of the most important parts of the process as it affects properties as porosity and surface cleaning of the samples, which greatly affected the quality of the capacitor. The sintered samples then underwent a process of anodic oxidation, which created a thin film of niobium pentóxido over the whole porous surface of the sample, this film is the dielectric capacitor. The oxidation process variables influence the performance of the film and therefore the capacitor. The samples were characterized by electrical measurements of capacitance, loss factor, ESR, relative density, porosity and surface area. After the characterizations was made an annealing in air ate 260ºC for 60min. After this treatment were made again the electrical measurements. The particle size of powders and sintering affected the porosity and in turn the specific area of the samples. The larger de area of the capacitor, greater is the capacitance. The powder showed the highest capacitance was with the smallest particle size. Higher temperatures and times of sintering caused samples with smaller surface area, but on the other hand the cleaning surface impurities was higher for this cases. So a balance must be made between the gain that is achieved with the cleaning of impurities and the loss with the decreased in specific area. The best results were obtained for the temperature of 1450ºC/60min. The influence of annealing on the loss factor and ESR did not follow a well-defined pattern, because their values increased in some cases and decreased in others. The most interesting results due to heat treatment were with respect to capacitance, which showed an increase for all samples after treatment

Estudo da adição de resíduo de scheelita em matriz cerâmica: formulação, propriedades físicas e microestrutura

Extractivism mineral is considered an activity highly degrading, due to the large volume of material that he moves in the form of ore and residues. The vast majority of mining companies do not show any technology or economically viable application that will allow the recycling of mineral residue, these being launched in areas receiving located the "open skies" degrade the environment. In Rio Grande do Norte to the production of ceramic red restricts their activities to the production of products such as: solid bricks, ceramic blocks, tiles, among others. Seeking to unite experiences and technical information that favor sustainable development, with important benefits to the construction sector and civil society in general, the present work studies the incorporation of the residue of scheelite in ceramic matrix kaolinitic, coming from the municipality of Boa Saúde - RN, in percentage of 5 %, 10 %, 20 %, 30% 40% and 50 %, by evaluating its microstructure, physical properties and formulation. The raw materials were characterized through the trials of X ray fluorescence, Diffraction of X rays, Differential Thermal Analysis and Termogravimetric Analysis. The samples were formed and fired at temperatures of 850o, 900o, 1000o, 1050o, 1100o, 1150o and 1200 oC, with isotherm of 1 hour and heating rate of 10 oC/min. Assays were performed technological of loss to fire, Water Absorption, Apparent Porosity, Apparent Density, Mass Loss in Fire and Bending Resistance; in addition to the Scanning Electron Microscopy, analyzing their physical and mechanical properties. The use of residue of scheelite in ceramic mass kaolinitic provided a final product with technological properties that meet the technical standards for the production of bricks and roofing tiles, with the percentage of 20% of waste that showed the best results

Avaliação da incorporação combinada dos resíduos de cascalho de perfuração de poço de petróleo e de polimento do porcelanato em cerâmica vermelha

Among the industries, those that produce ceramic porcelain for use in construction industry and oil, during the exploration and production period, play an important role in the production of waste. Much research has been carried out both by academia and the productive sector, sometimes reintroducing them in the same production line that generated them, sometimes in areas unrelated to their generation, as in the production of concrete and mortar for the construction, for example, but each one in an isolated way. In this research, the aim is to study the combined incorporation of the waste drill cuttings of oil well and the residue of the polishing of porcelain, generated in the final stage of finishing of this product in a clay matrix, for the production of red pottery, specifically bricks, ceramic blocks and tiles. The clay comes from the municipality of São Gonçalo, RN, the drilling waste is from the Natal basin, in Rio Grande do Norte, and the residue of the polishing proceeds from a ceramic porcelain of the State of Paraíba. For this purpose, we used a mixture of a plastic clay with a non-plastic, in a ratio of 50% each, settling formulations with the addition of these two residues in this clay matrix. In the formulations, both residues were incorporated with a minimum percentage of 2.5% and maximum of 12.5%, varying from 2.5% each, in each formulation, which the sum of the waste be no more than 15%. It should be noted that the residue of the polishing of ceramic porcelain is a IIa class (not inert). The materials were characterized by XRF, XRD, TG, DTA, laser granulometry and the plasticity index. The technological properties of water absorption, apparent porosity, linear shrinkage of burning, flexural tensile strength and bulk density were evaluated after the sintering of the pieces to 850 °C, 950 °C and 1050 °C, with a burning time of 3 hr, 3 hr and 30 minutes, and 3 hr and 50 minutes, respectively, with a heating rate of 10 °C/minute, for all formulations and landing of 30 minutes. To better understand the influence of each residue and temperature on the evaluated properties, we used the factorial planning and its surfaces of response for the interpretation of the results. It was found that the temperature has no statistical significance at a 95% of reliability level in flexural tensile strength and that it decreases the water absorption and the porosity, but increases the shrinkage and the bulk density. The results showed the feasibility of the desired incorporation, but adjusting the temperature to each product and formulation, and that the temperatures of 850 °C and 950 °C were the one that responded to the largest number of formulations

Estudo de reatores eletroquímicos para remoção de Cu2+ , Zn2+, Fenol e BTEX em água produzida

The production of water has become one of the most important wastes in the petroleum industry, specifically in the up stream segment. The treatment of this kind of effluents is complex and normally requires high costs. In this context, the electrochemical treatment emerges as an alternative methodology for treating the wastewaters. It employs electrochemical reactions to increase the capability and efficiency of the traditional chemical treatments for associated produced water. The use of electrochemical reactors can be effective with small changes in traditional treatments, generally not representing a significant additional surface area for new equipments (due to the high cost of square meter on offshore platforms) and also it can use almost the same equipments, in continuous or batch flow, without others high costs investments. Electrochemical treatment causes low environmental impact, because the process uses electrons as reagent and generates small amount of wastes. In this work, it was studied two types of electrochemical reactors: eletroflocculation and eletroflotation, with the aim of removing of Cu2+, Zn2+, phenol and BTEX mixture of produced water. In eletroflocculation, an electrical potential was applied to an aqueous solution containing NaCl. For this, it was used iron electrodes, which promote the dissolution of metal ions, generating Fe2+ and gases which, in appropriate pH, promote also clotting-flocculation reactions, removing Cu2+ and Zn2+. In eletroflotation, a carbon steel cathode and a DSA type anode (Ti/TiO2-RuO2-SnO2) were used in a NaCl solution. It was applied an electrical current, producing strong oxidant agents as Cl2 and HOCl, increasing the degradation rate of BTEX and phenol. Under different flow rates, the Zn2+ was removed by electrodeposition or by ZnOH formation, due the increasing of pH during the reaction. To better understand the electrochemical process, a statistical protocol factor (22) with central point was conducted to analyze the sensitivity of operating parameters on removing Zn2+ by eletroflotation, confirming that the current density affected the process negatively and the flow rate positively. For economical viability of these two electrochemical treatments, the energy consumption was calculated, taking in account the kWh given by ANEEL. The treatment cost obtained were quite attractive in comparison with the current treatments used in Rio Grande do Norte state. In addition, it could still be reduced for the case of using other alternative energy source such as solar, wind or gas generated directly from the Petrochemical Plant or offshore platforms

Automação da drenagem no teste de produção convencional em tanque cilíndrico

This document aims to improve the quality of the production test in vertical tanks with free water drain pipes, through a device to control the draining system. This proposal consists of an interface detector close to the tank bottle and a control valve on the pipe-drain; they are attached to a remote supervisor system, which will be minimizing the human influence in the conclusion of the test result. And for more consciousness the work shows the importance of the wells production test in the attendance and diagnosis of the productive process, informing the large number of tests executed and problems of the procedure adopted in the field today. There are many possible sources of uncertainty in this kind of test as shown in the experiments realized in the field; the object prototype of this dissertation will be made in the field, based upon the definition of parameters and characteristics of the devices proposal. For a better definition of the draining process the action results of the assessment test are shown, especially changed some for the understand ing of the real process. It shows the proposal details and the configuration that will be used in the tank of Monte Alegre s field Production Station, explaining the interface detector kind and the control system. It is the base to a pilot project now in development, named as the new project classified in the status of the new technology and production improvement of PETROBRAS in Rio Grande do Norte and Ceará. This dissertation concludes that the automation of the conventional test with the draining system will bring benefits both economically as metrologically, because it reduces the uncertainty of the test procedures with free water draining, and also decreases the number of tests with problems

Gerenciamento de alarmes em plataformas marítimas de produção de hidrocarbonetos: metodologia e estudo de caso

In the operational context of industrial processes, alarm, by definition, is a warning to the operator that an action with limited time to run is required, while the event is a change of state information, which does not require action by the operator, therefore should not be advertised, and only stored for analysis of maintenance, incidents and used for signaling / monitoring (EEMUA, 2007). However, alarms and events are often confused and improperly configured similarly by developers of automation systems. This practice results in a high amount of pseudo-alarms during the operation of industrial processes. The high number of alarms is a major obstacle to improving operational efficiency, making it difficult to identify problems and increasing the time to respond to abnormalities. The main consequences of this scenario are the increased risk to personal safety, facilities, environment deterioration and loss of production. The aim of this paper is to present a philosophy for setting up a system of supervision and control, developed with the aim of reducing the amount of pseudo-alarms and increase reliability of the information that the system provides. A real case study was conducted in the automation system of the offshore production of hydrocarbons from Petrobras in Rio Grande do Norte, in order to validate the application of this new methodology. The work followed the premises of the tool presented in ISA SP18.2. 2009, called "life cycle alarm . After the implementation of methodology there was a significant reduction in the number of alarms

Extração de boro de água produzida sintética por sistema microemulsionado

Boron is a semi-metal present in certain types of soils and natural waters. It is essential to the healthy development of plants and non-toxic to humans, depending on its concentration. It is used in various industries and it s present in water production coming from oil production. More specifically in Rio Grande do Norte, one of the largest oil producers on shore of Brazil, the relationship water/oil in some fields becomes more than 90%. The most common destination of this produced water is disposal in open sea after processing to meet the legal specification. In this context, this research proposes to study the extraction of boron in water produced by microemulsion systems for industrial utilization. It was taken into account the efficiency of extraction of boron related to surfactant (DDA and OCS, both characterized by FT-IR), cosurfactant (butanol and isoamyl alcohol), organic phase (kerosene and heptanes) and aqueous phase (solution of boron 3.6 ppm in alkaline pH). The ratio cosurfactant/ surfactant used was four and the percentage of organic phases for all points of study was set at 5%. It was chosen points with the highest percentage of aqueous phase. Each system was designed for three points of different compositions in relation to the constituents of a pseudoternary diagram. These points were chosen according to studies of phase behavior in pseudoternary diagrams made in previous studies. For this research, points were chosen in the Winsor II region. The excess aqueous solution obtained in these systems was separated and analyzed by ICP OES. For the data set obtained, the better efficiency in the extraction of boron was obtained using the system with DAC, isoamyl alcohol and heptanes, which extracted 49% in a single step. OCS was not viable to the extraction of boron by microemulsion system in the conditions defined in this study

Avaliação preliminar da contaminação por BTEX, em água subterrânea de poços tubulares, no município de Natal-RN

Among the different types of pollutants typically attributed to human activities, the petroleum products are one of the most important because of its toxic potential. This toxicity is attributed to the presence of substances such as benzene and its derivatives are very toxic to the central nervous system of man, with chronic toxicity, even in small concentrations. The area chosen for study was the city of Natal, capital of Rio Grande do Norte, where samples were collected in six different areas in the city, comprising 10 wells located in the urban area, being carried out in three distinct periods March/2009, December / June/2010 and 2009, and were evaluated for contamination by volatile hydrocarbons (BTEX - benzene, toluene, ethylbenzene and xylenes), so this work aimed to assess the quality of groundwater wells that supply funding for public supply and trade in the urban area of the city of Natal, in Rio Grande do Norte, contributing to the environmental assessment of the municipality. The analysis of BTEX in water was performed according to EPA Method 8021b. Was used the technique of headspace (TriPlus TP100) coupled to high resolution gas chromatography with selective photoionization detector (PID) and flame ionization (FID) - model Trace GC Ultra, Thermo Electron Corporation brand. The procedure adopted allowed the detection of concentrations of the order of μg.L-1. Data analysis with respect to BTEX in groundwater in the area monitored so far, shows that water quality is still preserved, because it exceeds the limits imposed by the potability Resolution CONAMA Nº. 396, April 2008

Fungos ectomicorrízicos em áreas de Mata Atlântica do Nordeste do Brasil

Ectomycorrhizal associations are poorly known from tropical lowlands of South America. Recent field trips to the reserve Parque Estadual das Dunas in Natal, in Rio Grande do Norte state, Brazil, revealed a undocumented community of ectomycorrhizal fungi. This type of Mycorrhizal association is frequently in the north hemisphere in temperate and boreal forests. The aim of this work is to analyze the occurrence of ectotrophic areas in atlantic rainforest. Collections along and around the trails in the reserve revealed six genera of putatively ECM fungi which belong to the basidiomycete, Amanitaceae, Boletaceae, Russulaceae, Entolomataceae, and Sclerodermataceae family which are poorly documented in Brazil. Plants belonging to Myrtaceae, Polygonaceae, Leguminosae/Caesalpinioideae, Erythroxylaceae, Malphigiaceae, Bromeliaceae, Loganiaceae, Sapotaceae e Celastraceae were found living next to the species of fungi analized. Our results suggest that the area studied is an ectotrophic environment which shows high diversity of putatively ECM fungi and some plants probably host ECM. The tropical lands are a potential focus to study reinforced by the new records of Scleroderma in Brazil and Northwest of Brazil

Diversidade de invertebrados em cavernas calcárias do oeste potiguar : subsídios para a determinação de áreas prioritárias para conservação.

It is estimated that the Brazilian karst areas sum about 200.000 km2. The caves, one of the main components of karst, are important windows into the biological studies on hypogean environments. In Rio Grande do Norte are known 563 caves, and 476 of them are in the municipalities of Baraúna, Felipe Guerra, Governador Dix-Sept Rosado, Apodi and Mossoró, the Western region of the State. However, like in the rest of the country, the cave fauna of the State is still poorly understood. This study used data from invertebrates harvested in 47 caves and aimed to analyze the effect of environmental change between the dry and rainy seasons in the communities of cave invertebrates, characterize these communities and evaluate the relationships between morphological and biotic variables of the caves and surroundings, and to define priority areas for conservation of cave environments of the study area from biotic parameters. Strong effects were found in the community structure of cave invertebrates due environmental changes between seasons, with values of total richness, abundance, diversity and ecological complexity significantly higher in the rainy season. It was possible to assess how the morphology of the cave and the external environment variables affect the biotic system, so that the variety of resources, forest cover in the vicinity, the area of the cave and its entrance were the variables that best explained the structure communities of cave invertebrates in the region. High values of total richness of invertebrates (36,62 ± 14,04 spp / cave) and troglomorphic species (61 species, mean 1,77 ± 2,34 spp / cave) were found and, given the biological relevance in the context of the area national and the imminent anthropogenic pressures existing, we defined four priority areas for actions aiming cave biodiversity conservation in the region.

A saúde psíquica de quem faz saúde: uma análise crítica sobre a humanização direcionada ao profissional de saúde

It is noticeable that pressure, tension and overwork are frequent in health professionals routine. The work related to the ward area demands deep attention and surveillance. Because of that, it is essential to have a specific look at the humanization directed at health professionals, considering that taking care of other human beings is the essence of their job. This study has analyzed the psychic health levels, as well as the stress health professionals are submitted to, providing a debate about the humanization in 06 public hospitals (03 of them awarded by actions of humanization, and 03 not awarded) in Rio Grande do Norte state, Brazil. A study with 126 active health professionals (doctors, nurses, psychologists, nutritionists and social workers) in ward areas in their respective institutions was carried out. The thesis presented, with multi-disciplinary characteristic, counted on the support of statisticians (to calculate samples and data analysis), psychologists, social workers and administrators (linked to the human resources sector in each hospital). A cross-sectional study was performed, taking into consideration both quantitative and qualitative factors. The tools used for that were a semistructured questionnaire with socio-demographic characteristics, work and humanization; Lipp's Stress Symptoms Inventory for Adults (ISSL), and the Goldberg s General Health Questionnaire (QSG). The workers are predominantly women (84,9%), married (54,8%), between 46 and 55 years old (40,5%), working in the same institution for more than 20 years (22,2%), and between 16 and 20 years (20,6%), respectively. They work 40 hours a week (71,4%) and have multiple jobs (61,9%). Although most of these individuals global psychic health is in a good level, there are a significant number of people that is gradually getting worse concerning psychic stress (F1) showed by QSG (54,7%), and stress showed by ISSL(42,1%). Observing the categories, nurses (41,5%). Nutritionists (20,8%), doctors and social workers (18,9%), were among the most affected. About general health (F6), 63% of the awarded hospitals and 70% of the not awarded ones, presented good health levels (ranging from 5 to 50%). It was also noticed that, in the groups mentioned above, 25 and 20% respectively, were inserted in scores between 55 to 90%, what means that they are in worsening phase. The fact that the hospital is awarded or well recognized doesn t interfere in health professionals stress level and in their psychic health. Through what was heard from these individuals, it was possible to verify that they know little about humanization, once few of them identify or know that the service they offer is in an adoption process by Ministerial Policies. It was also detected the necessity of developing actions aimed at worker s health. Such results showed the importance of have more investments in programs that are directed to workers well-being, because they deal with other people s health and it is known that it is difficult for them to offer high-quality assistance if there are not suitable physical, psychological and material conditions to help them develop their jobs. As a warning, it is fair to say that investments in actions that provide humanized care to health professionals, mainly concerning preventive care for their health and life quality in their work

Sistemas de informação geográfica e análise espacial de dados como ferramentas para determinação de agregação espacial de doenças: a hanseníase como modelo

This work demonstrates the importance of using tools used in geographic information systems (GIS) and spatial data analysis (SDA) for the study of infectious diseases. Analysis methods were used to describe more fully the spatial distribution of a particular disease by incorporating the geographical element in the analysis. In Chapter 1, we report the historical evolution of these techniques in the field of human health and use Hansen s disease (leprosy) in Rio Grande do Norte as an example. In Chapter 2, we introduced a few basic theoretical concepts on the methodology and classified the types of spatial data commonly treated. Chapters 3 and 4 defined and demonstrated the use of the two most important techniques for analysis of health data, which are data point processes and data area. We modelled the case distribution of Hansen s disease in the city of Mossoró - RN. In the analysis, we used R scripts and made available routines and analitical procedures developed by the author. This approach can be easily used by researchers in several areas. As practical results, major risk areas in Mossoró leprosy were detected, and its association with the socioeconomic profile of the population at risk was found. Moreover, it is clearly shown that his approach could be of great help to be used continuously in data analysis and processing, allowing the development of new strategies to work might increase the use of such techniques in data analysis in health care

Associação entre fatores nutricionais e a resposta frente à infecção por Leishmania chagasi

Leishmania chagasi infection presents a wide spectrum of clinical outcomes, ranging from asymptomatic self resolving infection to disease, visceral leishmaniasis (VL). The exact mechanisms that lead the evolution of infection to disease are not understood. It is believed that malnutrition is a risk factor associated with VL development, although there are few human studies in the area. We aimed to assess the nutritional factors associated with the response to L. chagasi infection in Rio Grande do Norte. The study was conducted from December 2006 to January 2008. 149 children were assessed: 20 active VL cases, 33 children with VL history, 40 DTH+ asymptomatic children and 56 DTH-. Nutritional status was assessed using z scores for Weight/Age, Weight/Height, Height/Age, Body Mass Index (BMI), and mid-upper arm circumference/height (MUAC/height). Vitamin A status was determined by serum retinol concentrations and the modified-relative-dose-esponse test (MRDR). Breastfeeding time and birth weight were also evaluated. VL children presented compromised nutritional status when compared to the other groups using BMI and MUAC/age, with means -1,53 ± 1,10 and -1,48 ± 1,28 z scores, respectively (ANOVA, p < 0,05). VL children also showed lower vitamin A levels: 43% presented serum retinol < 20 µg/dL and 15% MRDR > 0,060. Birth weight was inverserly associated with the risk to belong the VL group (β = -0,00; OR = 0,84; 95% CI 0,73 - 0,99; p = 0,047), whereas more breastfeeding time was directly associated with the risk to belong to the DTH+ group (β = 0,02; OD = 1,16; 95% CI 1,01 - 1,33; p = 0,036). The nutritional variables evaluated were associated with the response to the L. chagasi infection, with malnutrition and compromised vitamin A status as markers of children who present with VL. Higher birth weight was associated with protection to disease, and higher breastfeeding time was associated with increased likelihood of an asymptomatic infection. The results show that modifiable nutritional aspects in the study population are associated with the response to the L. chagasi infection

Síndrome metabólica e fatores associados: estudo comparativo com mulheres que apresentaram pré-eclâmpsia e gravidez normal, acompanhadas cinco anos após o parto

Preeclampsia is defined as an extremely serious complication of the pregnancy-puerperium cycle with delayed emergence of cardiovascular risk factors, including metabolic syndrome. The research aimed estimate the prevalences of metabolic syndrome and associated factors in women with preeclampsia and normal pregnancy followed five years after childbirth. This is a cross-sectional observational study using a quantitative approach, conducted at a maternity school in the city of Natal in Rio Grande do Norte state. The sample was composed of 70 women with previous preeclampsia and 75 normal selected by simple random probability sampling. Subjects were analyzed for sociodemographic, obstetric, clinical, anthropometric and biochemical parameters. International Diabetes Federation criteria were adopted to diagnose metabol ic syndrome. The Kolmogorov-Smirnov, Mann-Whitney, Student s t, Pearson s chi-squared, and Fisher s exact tests, in addition to simple logistic regression, were used for data analysis, at a 5% significance level (p ≤ 0.05). Statistical tests demonstrated elevated body mass index (p = 0.001), predominance of family history of diabetes mellitus (p = 0.022) and significantly higher prevalence of metabolic syndrome in the preeclampsia group (37.1%) when compared to normal (22.7%) (p = 0.042). Intergroup comparison showed a high number of metabolic syndrome components in women with previous preeclampsia. Altered systolic and diastolic blood pressure (p < 0.001) was the most prevalent, followed by low concentrations of high-density lipoproteins (p = 0.049), and hyperglycemia (p=0.030). There was a predominance of the metabolic syndrome in women with schooling 0-9 years (42.4%) (p = 0.005), body mass index above 30Kg.m 2 (52.3%) (p < 0.001), uric acid high (62.5%) (p = 0.050 and family history of hypertension (38.5%) (p< 0.001). Multivariate analysis of the data showed that the body mass index above 30 kg.m2, education level less than 10 years of study (p < 0.001) and family history of hypertension (p = 0.002) remained associated with the metabolic syndrome after multivariate analysis of the data. It is considered Women with previous preeclampsia exhibited high prevalence of metabolic syndrome and their individual components in relation to normal, especially, altered systolic and diastolic blood pressure, low concentrations of high-density lipoproteins and hyperglycemia. The factors associated to this ou tcome were obesity, less than 10 years of schooling, and family history of hypertension. Overall, this study identified young women with a history of PE exposed to a higher cardiovascular risk than normal

Estudo do perfil térmico de fornos do tipo "caipira" utilizados pelo setor de cerâmica vermelha em parelhas na região Seridó-RN

The present study aimed to characterize the thermal profile of wood fired oven used by the red ceramic industry in Parelhas, in the Seridó region/RN, aiming to propose structural interventions that can contribute to increasing productivity and product quality, optimize wood consumption and mitigate existing losses during the burning process. The study was conducted at Cerâmica Esperança in the city of Parelhas -RN, Brazil, during the period from August 2012 to September 2013. Four treatments were performed with three replicates, ie, with, a total of 12 experimental units (burnings). In the first stage 4 treatments were performed with three replicates, totaling 12 experimental units (firings). In the second stage 2 treatments were performed with three replications, totaling 6 experimental units (firings). The physical characteristics of the wood were analyzed using standard NBR 11941 and NBR 7190 for basic density and moisture, respectively. The clay was used as a reference parameter for distinguishing treatments. For both the analysis and characterization was carried out using techniques of fluorescence X (XRF) rays, X-ray diffraction (XRD) analysis, particle size analysis (FA). In the first and second stages were monitored: the time during the firing process, the amount of wood used at each firing, the number of parts enfornadas for subsequent determination of the percentages of losses, but also product quality. To characterize the thermal profile of the oven, we measured the temperature at 15 points scored in the surface charge put into the oven. Measurements were taken every 30 minutes from preheat until the end of burning, using a pyrometer laser sight sighting from preheating until the end of burning. In the second step 12 metal cylinders distributed on the oven walls, and the cylinder end walls 8 of the furnace 2 and rollers on each side walls are installed equidistant to 17 cm from the soil and the surface 30 of the wall are installed. The cylinders distributed on the front were placed 50 cm above the furnace, and the base of the oven 20 cm distant from the ground. 10 also thermocouples were installed, and five thermocouples distributed 1.77 cm above the combustion chambers, and one thermocouple on each side, and three thermocouples in front of the oven. We carried out the measurements of the temperatures every 1 hour during the burning two hours in cooling the cylinders with a pyrometer and thermocouples for dattaloger. These were fixed with depth of 30 cm from the wall. After statistical analysis it was found that: the thermal profile of the furnace surface and at different heights was heterogeneous; and the ranges of density and moisture content of wood are within recommended for use as an energy source standards. We conclude that even at low temperatures reached during firing there was a significant production of good quality products, this is due to high concentrations of iron oxide and potassium oxide found in clay, which lowers the melting point of the piece. The average burn time for each step varied 650-2100 minutes wood consumption was on average 20 m3, product quality was on average 16% of first quality, 70% second, third and 5% to 10% loss . The distance between the wire and the surface of the oven was a significant parameter for all treatments, but with different variations, meaning that the wire should not be so generic and unique form, used as a criterion for completion of the burn process. The central part of the furnace was the area that reached higher temperature, and in a unified manner, with the highest concentration of top quality products. The ideal temperature curve, which provided the highest quality of ceramic products was achieved in the central part of the furnace