987 resultados para Polyharmonic order of precision


Relevância:

100.00% 100.00%

Publicador:

Resumo:

The purpose of this paper is to characterize the optimal time paths of production and water usage by an agricultural and an oil sector that have to share a limited water resource. We show that for any given water stock, if the oil stock is sufficiently large, it will become optimal to have a phase during which the agricultural sector is inactive. This may mean having an initial phase during which the two sectors are active, then a phase during which the water is reserved for the oil sector and the agricultural sector is inactive, followed by a phase during which both sectors are active again. The agricultural sector will always be active in the end as the oil stock is depleted and the demand for water from the oil sector decreases. In the case where agriculture is not constrained by the given natural inflow of water once there is no more oil, we show that oil extraction will always end with a phase during which oil production follows a pure Hotelling path, with the implicit price of oil net of extraction cost growing at the rate of interest. If the natural inflow of water does constitute a constraint for agriculture, then oil production never follows a pure Hotelling path, because its full marginal cost must always reflect not only the imputed rent on the finite oil stock, but also the positive opportunity cost of water.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Uncertainties as to future supply costs of nonrenewable natural resources, such as oil and gas, raise the issue of the choice of supply sources. In a perfectly deterministic world, an efficient use of multiple sources of supply requires that any given market exhausts the supply it can draw from a low cost source before moving on to a higher cost one; supply sources should be exploited in strict sequence of increasing marginal cost, with a high cost source being left untouched as long as a less costly source is available. We find that this may not be the efficient thing to do in a stochastic world. We show that there exist conditions under which it can be efficient to use a risky supply source in order to conserve a cheaper non risky source. The benefit of doing this comes from the fact that it leaves open the possibility of using it instead of the risky source in the event the latter’s future cost conditions suddenly deteriorate. There are also conditions under which it will be efficient to use a more costly non risky source while a less costly risky source is still available. The reason is that this conserves the less costly risky source in order to use it in the event of a possible future drop in its cost.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Cette étude a pour but de tester si l’ajout de variables biomécaniques, telles que celles associées à la morphologie, la posture et l’équilibre, permet d’améliorer l’efficacité à dissocier 29 sujets ayant une scoliose progressive de 45 sujets ayant une scoliose non progressive. Dans une étude rétrospective, un groupe d’apprentissage (Cobb: 27,1±10,6°) a été utilisé avec cinq modèles faisant intervenir des variables cliniques, morphologiques, posturales et d’équilibre et la progression de la scoliose. Un groupe test (Cobb: 14,2±8,3°) a ensuite servit à évaluer les modèles dans une étude prospective. Afin d’établir l’efficacité de l’ajout de variables biomécaniques, le modèle de Lonstein et Carlson (1984) a été utilisé à titre d’étalon de mesures. Le groupe d’apprentissage a été utilisé pour développer quatre modèles de classification. Le modèle sans réduction fut composé de 35 variables tirées de la littérature. Dans le modèle avec réduction, une ANCOVA a servit de méthode de réduction pour passer de 35 à 8 variables et l’analyse par composantes principales a été utilisée pour passer de 35 à 7 variables. Le modèle expert fut composé de huit variables sélectionnées d’après l’expérience clinque. L’analyse discriminante, la régression logistique et l’analyse par composantes principales ont été appliquées afin de classer les sujets comme progressifs ou non progressifs. La régression logistique utilisée avec le modèle sans réduction a présenté l’efficience la plus élevée (0,94), tandis que l’analyse discriminante utilisée avec le modèle expert a montré l’efficience la plus faible (0,87). Ces résultats montrent un lien direct entre un ensemble de paramètres cliniques et biomécaniques et la progression de la scoliose idiopathique. Le groupe test a été utilisé pour appliquer les modèles développés à partir du groupe d’apprentissage. L’efficience la plus élevée (0,89) fut obtenue en utilisant l’analyse discriminante et la régression logistique avec le modèle sans réduction, alors que la plus faible (0,78) fut obtenue en utilisant le modèle de Lonstein et Carlson (1984). Ces valeurs permettent d’avancer que l’ajout de variables biomécaniques aux données cliniques améliore l’efficacité de la dissociation entre des sujets scoliotiques progressifs et non progressifs. Afin de vérifier la précision des modèles, les aires sous les courbes ROC ont été calculées. L’aire sous la courbe ROC la plus importante (0,93) fut obtenue avec l’analyse discriminante utilisée avec le modèle sans réduction, tandis que la plus faible (0,63) fut obtenue avec le modèle de Lonstein et Carlson (1984). Le modèle de Lonstein et Carlson (1984) n’a pu séparer les cas positifs des cas négatifs avec autant de précision que les modèles biomécaniques. L’ajout de variables biomécaniques aux données cliniques a permit d’améliorer l’efficacité de la dissociation entre des sujets scoliotiques progressifs et non progressifs. Ces résultats permettent d’avancer qu’il existe d’autres facteurs que les paramètres cliniques pour identifier les patients à risque de progresser. Une approche basée sur plusieurs types de paramètres tient compte de la nature multifactorielle de la scoliose idiopathique et s’avère probablement mieux adaptée pour en prédire la progression.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Les microcantileviers fonctionnalisés offrent une plateforme idéale pour la nano- et micro-mécanique et pour le développement de (bio-) capteurs tres sensible. Le principe d’opération consiste dans des évènements physicochimiques qui se passent du côté fonctionnalisé du microcantilevier induisant une différence de stress de surface entre les deux côtés du cantilevier qui cause une déflexion verticale du levier. Par contre, les facteurs et les phénomènes interfacials qui régissent la nature et l'intensité du stress de surface sont encore méconnus. Pour éclaircir ce phénomène, la première partie de cette thèse porte sur l'étude des réactions de microcantileviers qui sont recouverts d'or et fonctionnalisés par une monocouche auto-assemblée (MAA) électroactive. La formation d'une MAA de ferrocènylundécanethiol (FcC11SH) à la surface d'or d'un microcantilevier est le modèle utilisé pour mieux comprendre le stress de surface induit par l’électrochimie. Les résultats obtenus démontrent qu'une transformation rédox de la MAA de FcC11SH crée un stress de surface qui résulte dans une déflexion verticale du microcantilevier. Dépendamment de la flexibilité du microcantilevier, cette déflexion peut varier de quelques nanomètres à quelques micromètres. L’oxydation de cette MAA de FcC11SH dans un environnement d'ions perchlorate génère un changement de stress de surface compressive. Les résultats indiquent que la déflexion du microcantilevier est due à une tension latérale provenant d'une réorientation et d'une expansion moléculaire lors du transfért de charge et de pairage d’anions. Pour vérifier cette hypothèse, les mêmes expériences ont été répéteés avec des microcantileviers qui ont été couverts d'une MAA mixte, où les groupements électroactifs de ferrocène sont isolés par des alkylthiols inactifs. Lorsqu’un potentiel est appliqué, un courant est détecté mais le microcantilevier ne signale aucune déflexion. Ces résultats confirment que la déflexion du microcantilevier est due à une pression latérale provenant du ferrocènium qui se réorganise et qui crée une pression sur ses pairs avoisinants plutôt que du couplage d’anions. L’amplitude de la déflexion verticale du microcantilevier dépend de la structure moléculaire de la MAA et du le type d’anion utilisés lors de la réaction électrochimique. Dans la prochaine partie de la thèse, l’électrochimie et la spectroscopie de résonance de plasmon en surface ont été combinées pour arriver à une description de l’adsorption et de l’agrégation des n-alkyl sulfates à l’interface FcC11SAu/électrolyte. À toutes les concentrations de solution, les molécules d'agent tensio-actif sont empilées perpendiculairement à la surface d'électrode sous forme de monocouche condensé entrecroisé. Cependant, la densité du film spécifiquement adsorbé s'est avérée être affectée par l'état d'organisation des agents tensio-actifs en solution. À faible concentration, où les molécules d'agent tensio-actif sont présentes en tant que monomères solvatés, les monomères peuvent facilement s'adapter à l’évolution de la concentration en surface du ferrocènium lors du balayage du potential. Cependant, lorsque les molécules sont présentes en solution en tant que micelles une densité plus faible d'agent tensio-actif a été trouvée en raison de l'incapacité de répondre effectivement à la surface de ferrocenium générée dynamiquement.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

L'obligation de sécurité informationnelle - c'est-à-dire la tâche qui incombe aux entreprises d'assurer l'intégrité, la confidentialité et la disponibilité de l'information découle, tant en droit québécois que dans une majorité de juridictions occidentales, d'une série de dispositions législatives imposant non pas l'adoption de comportements ou l'utilisation de technologies ou de procédés identifiables, mais bien l'implantation de mesures de sécurité «raisonnables », «adéquates », ou « suffisantes ». Or, dans un domaine aussi embryonnaire et complexe que celui de la sécurité informationnelle, domaine dans lequel les solutions disponibles sont multiples et où la jurisprudence est éparse, comment une entreprise peut-elle jauger avec justesse l'étendue de son obligation? Bref, comment établir ce que ferait une entreprise raisonnablement prudente et diligente dans un domaine où il n'existe actuellement aucune balise législative, jurisprudentielle ou même coutumière permettant de fixer avec justesse le niveau de diligence imposé par le législateur? L'absence de sécurité juridique offerte par une telle situation est patente et nécessite une reconfiguration du cadre opératoire de l'obligation de sécurité informationnelle afin d'en identifier les composantes et les objectifs. Cet exercice passera par la redéfinition de l'obligation de sécurité informationnelle comme obligation de réduire les risques qui guettent l'information à un niveau socialement acceptable. En effet, la sécurité pouvant être définie comme étant la gestion du risque, c'est donc le risque qui réside au cœur de cette obligation. Or, en analysant les risques qui guettent un système, soit en analysant les menaces qui visent à exploiter ses vulnérabilités, il est possible d'établir quelles contre-mesures s'avèrent utiles et les coûts associés à leur mise en œuvre. Par la suite, il devient envisageable, en recourant à la définition économique de la négligence et en prenant compte des probabilités de brèches de sécurité et des dommages escomptés, d'établir les sommes optimales à investir dans l'achat, l'entretien et la mise à jour de ces contre-mesures. Une telle analyse permet ainsi de quantifier avec un certain degré de précision l'étendue de l'obligation de sécurité informationnelle en offrant aux entreprises un outil s'inspirant de données matérielles auxquelles elles ont librement accès et s'intégrant aisément dans le contexte juridique contemporain.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

La méthode de subdivision Catmull-Clark ainsi que la méthode de subdivision Loop sont des normes industrielle de facto. D'autre part, la méthode de subdivision 4-8 est bien adaptée à la subdivision adaptative, parce que cette méthode augmente le nombre de faces ou de sommets par seulement un facteur de 2 à chaque raffinement. Cela promet d'être plus pratique pour atteindre un niveau donné de précision. Dans ce mémoire, nous présenterons une méthode permettant de paramétrer des surfaces de subdivision de la méthode Catmull-Clark et de la méthode 4-8. Par conséquent, de nombreux algorithmes mis au point pour des surfaces paramétriques pourrant être appliqués aux surfaces de subdivision Catmull-Clark et aux surfaces de subdivision 4-8. En particulier, nous pouvons calculer des bornes garanties et réalistes sur les patches, un peu comme les bornes correspondantes données par Wu-Peters pour la méthode de subdivision Loop.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Ce mémoire présente l’application de la méthode de décomposition en termes de diagrammes aux désintégrations de mésons B vers trois mésons de type pseudos- calaire ne comportant pas de quarks charmés. La décomposition diagrammatique des désintégrations de types B → Kππ, B → KKK ̄, B → KK ̄π et B → πππ est effectuée de façon systématique. Il est démontré que lorsque l’on néglige les dia- grammes d’échanges et d’annihilations, dont les contributions sont estimées être petites, de nouvelles relations apparaissent entre les amplitudes. Ces relations sont de nouveaux tests du modèle standard qui ne peuvent être obtenus que par la méthode diagrammatique. Lorsque les données nécessaires sont disponibles, nous vérifions ces relations et obtenons un bon accord avec les données expérimentales. Nous démontrons également qu’il est possible d’utiliser le secteur B → Kππ pour mesurer la phase faible γ avec une incertitude théorique que nous estimons être de l’ordre de 5%. Les autres secteurs de désintégrations ne permettent d’extraire des phases faibles que si l’on invoque des approximations de précisions inconnues.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In recent years scientists have made rapid and significant advances in the field of semiconductor physics. One of the most important fields of current interest in materials science is the fundamental aspects and applications of conducting transparent oxide thin films (TCO). The characteristic properties of such coatings are low electrical resistivity and high transparency in the visible region. The first semitransparent and electrically conducting CdO film was reported as early as in 1907 [1]. Though early work on these films was performed out of purely scientific interest, substantial technological advances in such films were made after 1940. The technological interest in the study of transparent semiconducting films was generated mainly due to the potential applications of these materials both in industry and research. Such films demonstrated their utility as transparent electrical heaters for windscreens in the aircraft industry. However, during the last decade, these conducting transparent films have been widely used in a variety of other applications such as gas sensors [2], solar cells [3], heat reflectors [4], light emitting devices [5] and laser damage resistant coatings in high power laser technology [6]. Just a few materials dominate the current TCO industry and the two dominant markets for TCO’s are in architectural applications and flat panel displays. The architectural use of TCO is for energy efficient windows. Fluorine doped tin oxide (FTO), deposited using a pyrolysis process is the TCO usually finds maximum application. SnO2 also finds application ad coatings for windows, which are efficient in preventing radiative heat loss, due to low emissivity (0.16). Pyrolitic tin oxide is used in PV modules, touch screens and plasma displays. However indium tin oxide (ITO) is mostly used in the majority of flat panel display (FPD) applications. In FPDs, the basic function of ITO is as transparent electrodes. The volume of FPD’s produced, and hence the volume of ITO coatings produced, continues to grow rapidly. But the current increase in the cost of indium and the scarcity of this material created the difficulty in obtaining low cost TCOs. Hence search for alternative TCO materials has been a topic of active research for the last few decades. This resulted in the development of binary materials like ZnO, SnO2, CdO and ternary materials like II Zn2SnO4, CdSb2O6:Y, ZnSO3, GaInO3 etc. The use of multicomponent oxide materials makes it possible to have TCO films suitable for specialized applications because by altering their chemical compositions, one can control the electrical, optical, chemical and physical properties. But the advantages of using binary materials are the easiness to control the chemical compositions and depositions conditions. Recently, there were reports claiming the deposition of CdO:In films with a resistivity of the order of 10-5 ohm cm for flat panel displays and solar cells. However they find limited use because of Cd-Toxicity. In this regard, ZnO films developed in 1980s, are very useful as these use Zn, an abundant, inexpensive and nontoxic material. Resistivity of this material is still not very low, but can be reduced through doping with group-III elements like In, Al or Ga or with F [6]. Hence there is a great interest in ZnO as an alternative of ITO. In the present study, we prepared and characterized transparent and conducting ZnO thin films, using a cost effective technique viz Chemical Spray Pyrolysis (CSP). This technique is also suitable for large area film deposition. It involves spraying a solution, (usually aqueous) containing soluble salts of the constituents of the desired compound, onto a heated substrate.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Heterotrophic bacterial flora of Pmonadon from an apparently healthy hatchery system as well as a pool with heavy mortality were isolated and studied. In the healthy systems comparatively higher generic diversity with Pseudomonas, Acinetobacter, Bacillus, Micrococcus, members of the family Enterobacteriaceae and coryneform group in the diminishing order of dominance was recorded. Meanwhile from the moribund larvae and rearing water Aeromonas and Pseudomonas could be isolated in almost equal proportions. Strikingly, Aeromonas could not be isolated from the apparently healthy larval rearing system and its exclusive occurrence in the sick culture system in comparatively higher percentage suggested its possible role in the mortality. They were found to be highly halophilic exhibiting growth at 10% NaCl. On testing their sensitivity to twenty antibiotics, four of them (Streptomycin, Gentamycin, Methamine mandelate and Cloramphenicol) were found to be effective on all the isolates of Aeromonas and Pseudomonas suggesting their possible application in the hatchery system in times of emergency. While doing so, Streptomycin would do comparatively better than the others as the minimum inhibitory dose required was comparatively lower (200ppm) within a period of 24 hours

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The thesis presents the dynamics of a polymer chain under tension. It includes existing theories of polymer fracture, important theories of reaction rates, the rate using multidimensional transition state theory and apply it to the case of polyethylene etc. The main findings of the study are; the life time of the bond is somewhat sensitive to the potential lead to rather different answers, for a given potential a rough estimate of the rate can be obtained by a simples approximation that considers the dynamics of only the bond that breaks and neglects the coupling to neighboring bonds. Dynamics of neighboring bonds would decrease the rate, but usually not more than by one order of magnitude, for the breaking of polyethylene, quantum effects are important only for temperatures below 150K, the lifetime strongly depends on the strain and as the strain varies over a narrow range, the life varies rapidly from 105 seconds to 10_5 seconds, if we change one unit of the polymer by a foreign atom, say by one sulphure atom, in the main chain itself, by a weaker bond, the rate is found to increase by orders of magnitude etc.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A fibre optic technique for detecting trace amounts of nitrite compounds in water is described. The off-line fibre optic sensor outlined here is based on evanescent field absorption in a test solution formed by the reaction of nitrite compounds in water with suitable chemical reagents. A short unclad portion of a plastic clad silica fibre acts as the sensing region. The experimental results clearly establish the usefulness of the present technique for detecting very low concentrations of the order of 1 ppb (parts per billion) of nitrite compounds with a large dynamic range of 1–1000 ppb. Such a high sensitivity enables the present device to be used for measuring the nitrite content in drinking water.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The design and development of a fibre optic evanescent wave refractometer for the detection of trace amounts of paraffin oil and palm oil in coconut oil is presented. This sensor is based on a side-polished plastic optical fibre. At the sensing region, the cladding and a small portion of the core are removed and the fibre nicely polished. The sensing region is fabricated in such a manner that it sits perfectly within a bent mould. This bending of the sensing region enhances its sensitivity. The oil mixture of different mix ratios is introduced into the sensing region and we observed a sharp decrease in the output intensity. The observed variation in the intensity is found to be linear and the detection limit is 2% (by volume) paraffin oil/palm oil in coconut oil. The resolution of this refractometric sensor is of the order of 10−3. Since coconut oil is consumed in large volumes as edible oil in south India, this fibre optic sensor finds great relevance for the detection of adulterants such as paraffin oil or palm oil which are readily miscible in coconut oil. The advantage of this type of sensor is that it is inexpensive and easy to set up. Another attraction of the side-polished fibre is that only a very small amount of analyte is needed and its response time is only 7 s.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A silver target kept under partial vacuum conditions was irradiated with focused nanosecond pulses at 1:06 mm from a Nd:YAG laser. The electron emission monitored with a Langmuir probe shows a clear twin-peak distribution. The first peak which is very sharp has only a small delay and it indicates prompt electron emission with energy as much as 60 5 eV. Also the prompt electron emission shows a temporal profile with a width that is same as that for the laser pulse whereas the second peak is broader, covers several microseconds, and represents the low-energy electrons (2 0:5 eV) associated with the laser-induced silver plasma as revealed by time-of-flight measurements. It has been found that prompt electrons ejected from the target collisionally excite and ionize ambient gas molecules. Clearly resolved rotational structure is observed in the emission spectra of ambient nitrogen molecules. Combined with time-resolved spectroscopy, the prompt electrons can be used as excitation sources for various collisional excitation–relaxation experiments. The electron density corresponding to the first peak is estimated to be of the order of 1017 cm?--3 and it is found that the density increases as a function of distance away from the target. Dependence of probe current on laser intensity shows plasma shielding at high laser intensities.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This thesis presents in detail. the theoretical developments and calculations which are used for the simultaneous determination of thermal parameters, namely thermal diffusivity (a). thermal effusivity (e), thermal conductivity (K) and heat capacity (cr ) employing photopyroelectric technique. In our calculations. we have assumed that the pyroelectric detector is supported on a copper backing. so that there will be sufficient heat exchange between the heated pyroelectric detector and the backing so that the signal fluctuations are reduced to a minimum. Since the PPE signal depends on the properties of the detector that are also temperature dependent. a careful temperature calibration of the system need to be carried out. APPE cell has been fabricated for the measurements that can be used to measure the thermal properties of solid samples from ~ 90 K to ~ 350 K. The cell has been calibrated using standard samples and the accuracy of the technique is found to be of the order of± 1%.In this thesis, we have taken up work n photopyroelectric investigation of thermal parameters of ferroelectric crystals such as Glycine phosphite (NH3CH2COOH3P03), Triglycine sulfate and Thiourea as well as mixed valence perovskites samples such as Lead doped Lanthanum Manganate (Lal_xPb~Mn03) Calcium doped (Lal_xCaxMnOJ) and Nickel doped Lanthanum Stroncium Cobaltate (Lao~Sro5Ni,Col_x03).The three ferroelectric crystals are prepared by the slow evaporation technique and the mixed valence perovskites by solid state reaction technique.Mixed valence perovskites, with the general formula RI_xA~Mn03 (R = La. Nd or Pr and A = Ba, Ca, Sr or Pb) have been materials of intense experimental and theoretical studies over the past few years. These materials show . colossal magneloresis/ance' (CMR) in samples with 0.2 < x < 0.5 in such a doping region, resistivity exhibits a peak at T = T p' the metal - insulator transition temperature. The system exhibits metallic characteristics with d %T > Oabove Tp (wherep is the resistivity) and insulating characteristics with d % T < 0 above T p. Despite intensive investigations on the CMR phenomena and associated electrical properties. not much work has been done on the variation of thermal properties of these samples. We have been quite successful in finding out the nature of anomaly associated with thermal properties when the sample undergoes M-I transition.The ferroelectric crystal showing para-ferroelectric phase transitions - Glycine phosphite. Thiourea and Triglycine sulfate - are studied in detail in order to see how well the PPE technique enables one to measure the thermal parameters during phase transitions. It is seen that the phase transition gets clearly reflected in the variation of thermal parameters. The anisotropy in thermal transport along different crystallographic directions are explained in terms of the elastic anisotropy and lattice contribution to the thermal conductivity. Interesting new results have been obtained on the above samples and are presented in three different chapters of the thesis.In summary. we have carried investigations of the variations of the thermal parameters during phase transitions employing photopyroelectric technique. The results obtained on different systems are important not only in understanding the physics behind the transitions but also in establishing the potentiality of the PPE tool. The full potential of PPE technique for the investigation of optical and thermal properties of materials still remains to be taken advantage of by workers in this field.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

A laser produced plasma from the multielement solid target YBa2Cu3O7 is generated using 1.06 μm, 9 ns pulses from a Q-switched Nd:YAG laser in air at atmospheric pressure. A time resolved analysis of the profile of the 4554.03 Å resonance line emission from Ba II at various laser power densities has been carried out. It has been found that the line has a profile which is strongly self-reversed. It is also observed that at laser power densities equal to or exceeding 1.6×1011 W cm−2, a third peak begins to develop at the centre of the self-reversed profile and this has been interpreted as due to the anisotropic resonance scattering (fluorescence). The number densities of singly ionized barium ions evaluated from the width of the resonance line as a function of time delay with respect to the beginning of the laser pulse give typical values of the order of 1019 cm−3. The higher ion concentrations existing at smaller time delays are seen to decrease rapidly. The Ba II ions in the ground state resonantly absorb the radiation and this absorption is maximum around 120 ns after the laser pulse.