938 resultados para PARTICLE CORRELATIONS AND FLUCTUATIONS


Relevância:

100.00% 100.00%

Publicador:

Resumo:

The oxygen reduction reaction (ORR) was investigated on carbon-supported Pt-Co nanoparticle electrocatalysts with low Pt content in alkaline electrolyte. High resolution transmission electron microscopy, In situ X-ray absorption spectroscopy, and X-ray diffraction analysis evidenced large structural differences of the Pt-Co particles depending oil the route of the catalyst synthesis. It was demonstrated that although the Pt-Co materials contain low amounts of Pt, they show very good activities when the particles are formed by a Pt-rich shell and a Pt-Co core, which was obtained after submitting the electrocatalyst to a potential cycling in acid electrolyte. The high activity of this material was due to a major contribution from its higher surface area, as a result of the leaching of the Co atoms from the particle Surface. Furthermore, its high activity was ascribed to a minor contribution from the electronic interaction of the Pt atoms, at the particle surface, and the Co atoms located in the beneath layer, lowering the Pt cl-band center. As these electrocatalysts presented high activity for the ORR with low Pt content, the cost of the fuel cell cathodes could be lowered considerably. (c) 2009 Elsevier B.V. All rights reserved.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Herein, we report a new approach of an FePt nanoparticle formation mechanism studying the evolution of particle size and composition during the synthesis using the modified polyol process. One of the factors limiting their application in ultra-high-density magnetic storage media is the particle-to-particle composition, which affects the A1-to-L1(0) transformation as well as their magnetic properties. There are many controversies in the literature concerning the mechanism of the FePt formation, which seems to be the key to understanding the compositional chemical distribution. Our results convincingly show that, initially, Pt nuclei are formed due to reduction of Pt(acac)(2) by the diol, followed by heterocoagulation of Fe cluster species formed from Fe(acac)(3) thermal decomposition onto the Pt nuclei. Complete reduction of heterocoagulated iron species seems to involve a CO-spillover process, in which the Pt nuclei surface acts as a heterogeneous catalyst, leading to the improvement of the single-particle composition control and allowing a much narrower compositional distribution. Our results show significant decreases in the particle-to-particle composition range, improving the A1-to-L1(0) phase transformation and, consequently, the magnetic properties when compared with other reported methods.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Sedan fotbollens början 1863 har sporten idag vuxit till en mångmiljardindustri. Detta innebär att klubbarna framställs mer som företag där den visuella identiteten är en viktig faktor när det kommer till marknadsföring. Syftet med denna studie är att jämföra 98 europeiska fotbollsklubbars logotyper från fem olika ligor för att hitta samband och skillnader i utformningen mellan länder och ligor. Resultatet sammanfattades i form av generiska logotyper för respektive liga. De 98 klubbarna hämtades ur de fem europeiska ligor som 2014 hade störst tv-intäkter. Logotyperna samlades in genom bildsökningar via Google. Logotyperna sorterades efter respektive liga och överskådades för att definiera lämpliga kategorier för en visuell innehållsanalys. Den visuella innehållsanalysen visade att ligorna skiljer sig något vad beträffar logotypernas utformning, men att de har vissa gemensamma grundläggande drag.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The AFN1 gene is transiently expressed in germinating oat grains. As AFN1 is not expressed in dormant oat grains during imbibition, we hypothesize that AFN1 may be involved in stimulating the germination process. Sequence analysis of an AFN1 cDNA clone indicates that the AFN1 polypeptide is similar to a previously identified abscisic acid (ABA) glucosyl transferase. This suggests that AFN1 may be acting to glucosylate ABA, thereby inactivating it. As the hormone ABA is known to inhibit germination, ABA glucosylation/inactivation could lead to germination in grains expressing AFN1. To test this hypothesis, we have constructed an expression plasmid that encodes an MBP::AFN1 (maltose binding protein) fusion protein. E. coli cells carrying the expression plasmid were found to produce the MBP::AFN1 fusion protein as a substantial fraction of total protein. We are currently in the process of purifying the MBP::AFN1 fusion protein by affinity chromatography, so that it can be assayed for ABA glucosyl transferase activity. We also wish to test the effect of AFN1 gene expression during grain imbibition on the germination behavior of the grains. To this end, we have constructed plasmids for the overexpression and RNAi-based suppression of AFN1 in transgenic plants. These plasmids have been introduced into oat cells by particle bombardment and we are in the process of regenerating transgenic plants for study.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Foi construído um equipamento que possibilitou a determinação dos parâmetros de fluidização de amostras de granulometrias simples e de misturas binárias, de carvão de Charqueadas com granulonetrias entre 9 e 28 malhas (mesh number), à temperatura ambiente, tendo-se obtido uma correlação para o cálculo da velocidade mínima de fluidização em função do diâmetro das partículas.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Os resultados obtidos possibilitam afirmar que as indústrias que mais investiram em Tecnologia de Informação (TI), no período de 2001 a 2011, obtiveram maior crescimento da sua receita operacional e resultados operacionais mais eficazes, comparadas com as indústrias que investiram menos no período. De acordo com o modelo proposto, para as empresas estudadas foi possível encontrar, no prazo de dois anos, um crescimento de 7% no resultado operacional para cada 1% a mais de investimentos em TI. Destaca-se o objetivo da pesquisa de identificar e analisar os impactos dos gastos e investimentos em tecnologia de informação no desempenho financeiro das indústrias brasileiras, para alcançá-lo, adotou-se um modelo de pesquisa que utilizou métricas contábeis-financeiras e indicadores de uso TI, bem como a combinação de técnicas estatísticas para as análises. O trabalho aprofunda e amplia as discussões existentes sobre a avaliação dos investimentos em TI e como aferir o impacto desta sobre o desempenho organizacional. O universo do estudo foi composto pelas companhias brasileiras, de capital aberto, do ramo industrial, com ações ativas na BOVESPA, totalizando 119 companhias. Por meio de uma survey obteve-se os dados complementares referentes aos gastos e investimentos em TI; os questionários semiestruturados foram encaminhados diretamente ao Gerente de TI (Chief Information Officer). Estes esforços na coleta de dados primários possibilitaram a obtenção de uma amostra bastante significativa, com 63 indústrias, ou seja, 53% da população estudada. Após coleta, a análise dos dados foi desenvolvida em três etapas: (1) Análise Fatorial (AF) para seleção de fatores de desempenho que resultou no final do processo em doze variáveis para o modelo da pesquisa; (2) Análise de Cluster (AC) que evidenciou três agrupamentos distintos de indústrias por suas características e desempenho e (3) Regressão Múltipla que adotou um modelo econométrico dinâmico, estimado pelo Método dos Momentos Generalizado (GMM), satisfazendo as condições do modelo de Arellano-Bond (1991). Salienta-se que o modelo proposto permitiu tratar de forma adequada metodologicamente as correlações espúrias, possibilitando identificar que os gastos e investimentos em TI, (IGTI t-2), de dois períodos anteriores impactaram no Resultado Operacional Atual, (ROPt), evidenciando o efeito tardio, ou lag effect. Além disso, foi constatado que outras variáveis de rentabilidade e liquidez impactam neste resultado, também adotando defasagem das variáveis. A principal variável de TI da pesquisa, o IGTI, é calculada pela soma de gastos e investimentos em TI anuais (OPEX/CAPEX), dividida pela Receita Operacional Líquida anual. Para pesquisas futuras, há a possibilidade de buscar medidas de avaliação por tipos (categorias) de investimento em TI, visando ao aprofundamento da análise destes impactos no desempenho setorizado (ligado a cada investimento) e da análise de clusters, adotando o modelo de análise da pesquisa.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In this work, was studied the formation of a composite of the refractory metal niobium with copper, through the process of high-energy milling and liquid phase sintering. The HEM can be used to synthesize composite powders with high homogeneity and fine size particle distribution. It may also produce the solid solubility in immiscible systems such as Nb-Cu, or extend the solubility of systems with limited solubility. Therefore, in the immiscible system Cu-Nb, the high-energy milling was successfully used to obtain the composite powder particles. Initially, the formation of composite particles during the HEM and the effect of preparation technique on the microstructure of the material was evaluated. Four loads of Nb and Cu powders containing 20%wt Cu were synthesized by MAE in a planetary type ball mill under different periods of grinding. The influence of grinding time on the metal particles is evaluated during the process by the withdrawal of samples at intermediate times of milling. After compaction under different forces, the samples were sintered in a vacuum furnace. The liquid phase sintering of these samples prepared by HEM produced a homogeneous and fine grained. The composite particles forming the sintered samples are the addition of a hard phase (Nb) with a high melting point, and a ductile phase (Cu) with low melting point and high thermal and electrical conductivities. Based on these properties, the Nb-Cu system is a potential material for many applications, such as electrical contacts, welding electrodes, coils for generating high magnetic fields, heat sinks and microwave absorbers, which are coupled to electronic devices. The characterization techniques used in this study, were laser granulometry, used to evaluate the homogeneity and particle size, and the X-ray diffraction, in the phase identification and to analyze the crystalline structure of the powders during milling. The morphology and dispersion of the phases in the composite powder particles, as well the microstructures of the sintered samples, were observed by scanning electron microscopy (SEM). Subsequently, the sintered samples are evaluated for density and densification. And finally, they were characterized by techniques of measuring the electrical conductivity and microhardness, whose properties are analyzed as a function of the parameters for obtaining the composite

Relevância:

100.00% 100.00%

Publicador:

Resumo:

This masther dissertation presents a contribution to the study of 316L stainless steel sintering aiming to study their behavior in the milling process and the effect of isotherm temperature on the microstructure and mechanical properties. The 316L stainless steel is a widely used alloy for their high corrosion resistance property. However its application is limited by the low wear resistance consequence of its low hardness. In previous work we analyzed the effect of sintering additives as NbC and TaC. This study aims at deepening the understanding of sintering, analyzing the effect of grinding on particle size and microstructure and the effect of heating rate and soaking time on the sintered microstructure and on their microhardness. Were milled 316L powders with NbC at 1, 5 and 24 hours respectively. Particulates were characterized by SEM and . Cylindrical samples height and diameter of 5.0 mm were compacted at 700 MPa. The sintering conditions were: heating rate 5, 10 and 15◦C/min, temperature 1000, 1100, 1200, 1290 and 1300◦C, and soaking times of 30 and 60min. The cooling rate was maintained at 25◦C/min. All samples were sintered in a vacuum furnace. The sintered microstructure were characterized by optical and electron microscopy as well as density and microhardness. It was observed that the milling process has an influence on sintering, as well as temperature. The major effect was caused by firing temperature, followed by the grinding and heating rate. In this case, the highest rates correspond to higher sintering.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Over recent years the structural ceramics industry in Brazil has found a very favorable market for growth. However, difficulties related to productivity and product quality are partially inhibiting this possible growth. An alternative for trying to solve these problems and, thus, provide the pottery industry the feasibility of full development, is the substitution of firewood used in the burning process by natural gas. In order to contribute to this process of technological innovation, this paper studies the effect of co-use of ceramic phyllite and kaolin waste on the properties of a clay matrix, verifying the possible benefits that these raw materials can give to the final product, as well as the possibility of such materials to reduce the heat load necessary to obtain products with equal or superior quality. The study was divided into two steps: characterization of materials and study of formulations. Two clays, a phyllite and a residue of kaolin were characterized by the following techniques: laser granulometry, plasticity index by Atterberg limits, X-ray fluorescence, X-ray diffraction, mineralogical composition by Rietveld, thermogravimetric and differential thermal analysis. To study the formulations, specifically for evaluation of technological properties of the parts, was performed an experimental model that combined planning involving a mixture of three components (standard mass x phyllite x kaolin waste) and a 23 factorial design with central point associated with thermal processing parameters. The experiment was performed with restricted strip-plot randomization. In total, 13 compositional points were investigated within the following constraints: phyllite ≤ 20% by weight, kaolin waste ≤ 40% by weight, and standard mass ≥ 60% by weight. The thermal parameters were used at the following levels: 750 and 950 °C to the firing temperature, 5 and 15 °C/min at the heating rate, 15 and 45min to the baseline. The results showed that the introduction of phyllite and/or kaolin waste in ceramic body produced a number of benefits in properties of the final product, such as: decreased absorption of water, apparent porosity and linear retraction at burn; besides the increase in apparent specific mass and mechanical properties of parts. The best results were obtained in the compositional points where the sum of the levels of kaolin waste and phyllite was maximal (40% by weight), as well as conditions which were used in firing temperatures of 950 °C. Regarding the prospect of savings in heat energy required to form the desired microstructure, the phyllite and the residue of kaolin, for having small particle sizes and constitutions mineralogical phases with the presence of fluxes, contributed to the optimization of the firing cycle.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

In recent years, the area of advanced materials has been considerably, especially when it comes to materials for industrial use, such as is the case with structured porosity of catalysts suitable for catalytic processes. The use of catalysts combined with the fast pyrolysis process is an alternative to the oxygenate production of high added value, because, in addition to increasing the yield and quality of products, allows you to manipulate the selectivity to a product of interest, and therefore allows greater control over the characteristics of the final product. Based on these arguments, in this work were prepared titanium catalysts supported on MCM-41 for use in catalytic pyrolysis of biomass, called elephant grass. The reactions of pyrolysis of biomass were performed in a micro pyrolyzer, Py-5200, coupled to GC / MS, the company CDS Corporation, headquartered in the United States. The catalysts Ti-MCM-41 in different molar ratios were characterized by XRD, TG / DTG, FT-IR, SEM, XRF, UV-visible adsorption of nitrogen and the distribution of particle diameter and specific surface area measurement by the BET method. From the catalytic tests it was observed that the catalysts synthesized showed good results for the pyrolysis reaction.The main products were obtained a higher yield of aldehydes, ketones and furan. It was observed that the best reactivity is a direct function of the ratio Si/Ti, nature and concentration of the active species on mesoporous supports. Among the catalysts Ti-MCM-41 (molar ratio Si / Ti = 25 and 50), the ratio Si / Ti = 25 (400 ° C and 600 ° C) favored the cracking of oxygenates such as acids , aldehydes, ketones, furans and esters. Already the sample ratio Si / Ti = 50 had the highest yield of aromatic oxygenates

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The multiphase flow occurrence in the oil and gas industry is common throughout fluid path, production, transportation and refining. The multiphase flow is defined as flow simultaneously composed of two or more phases with different properties and immiscible. An important computational tool for the design, planning and optimization production systems is multiphase flow simulation in pipelines and porous media, usually made by multiphase flow commercial simulators. The main purpose of the multiphase flow simulators is predicting pressure and temperature at any point at the production system. This work proposes the development of a multiphase flow simulator able to predict the dynamic pressure and temperature gradient in vertical, directional and horizontal wells. The prediction of pressure and temperature profiles was made by numerical integration using marching algorithm with empirical correlations and mechanistic model to predict pressure gradient. The development of this tool involved set of routines implemented through software programming Embarcadero C++ Builder® 2010 version, which allowed the creation of executable file compatible with Microsoft Windows® operating systems. The simulator validation was conduct by computational experiments and comparison the results with the PIPESIM®. In general, the developed simulator achieved excellent results compared with those obtained by PIPESIM and can be used as a tool to assist production systems development

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Injectivity decline, which can be caused by particle retention, generally occurs during water injection or reinjection in oil fields. Several mechanisms, including straining, are responsible for particle retention and pore blocking causing formation damage and injectivity decline. Predicting formation damage and injectivity decline is essential in waterflooding projects. The Classic Model (CM), which incorporates filtration coefficients and formation damage functions, has been widely used to predict injectivity decline. However, various authors have reported significant discrepancies between Classical Model and experimental results, motivating the development of deep bed filtration models considering multiple particle retention mechanisms (Santos & Barros, 2010; SBM). In this dissertation, inverse problem solution was studied and a software for experimental data treatment was developed. Finally, experimental data were fitted using both the CM and SBM. The results showed that, depending on the formation damage function, the predictions for injectivity decline using CM and SBM models can be significantly different

Relevância:

100.00% 100.00%

Publicador:

Resumo:

Modeling transport of particulate suspensions in porous media is essential for understanding various processes of industrial and scientific interest. During these processes, particles are retained due to mechanisms like size exclusion (straining), adsorption, sedimentation and diffusion. In this thesis, a mathematical model is proposed and analytical solutions are obtained. The obtained analytic solutions for the proposed model, which takes pore and particle size distributions into account, were applied to predict the particle retention, pore blocking and permeability reduction during dead-end microfiltration in membranes. Various scenarios, considering different particle and pore size distributions were studied. The obtained results showed that pore blocking and permeability reduction are highly influenced by the initial pore and particle size distributions. This feature was observed even when different initial pore and particle size distributions with the same average pore size and injected particle size were considered. Finally, a mathematical model for predicting equivalent permeability in porous media during particle retention (and pore blocking) is proposed and the obtained solutions were applied to study permeability decline in different scenarios

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The reaction of post-consumer poly(ethylene terephthalate) with aqueous solutions of sulfuric acid 7.5M was investigated in terms of temperature, time and particle size. The reaction extent reached 80% in four days at 100 degrees C and 90% in 5 hours at 135 degrees C. TPA obtained was purified and considered in the same level of quality of the commercial one after tests of elemental analysis, particle size and color. It was concluded that the hydrolysis occurred preferentially at the chain ends and superficially, having as controller mechanism the acid diffusion into the polymer structure. The shrinking-core model can explain the reaction kinetics.

Relevância:

100.00% 100.00%

Publicador:

Resumo:

The inorganic actives, represented mainly by microfine zinc oxide and titanium dioxide, have shown great potential to protect against large UV spectrum. The aim of this study is the development, characterization and analysis of stability in the short term of microemulsions containing inorganic fotoprotection agents. The microemulsions identified by the phases diagram containing the metallic oxides were produced by two different methods and subjected to the centrifugation test and thermal stress cycles, and subsequently characterized by macroscopic evaluation, test dilution, electrical conductivity, pH, particle size, and zeta potential. This study highlights the influence of the metal oxides addition in the structure and distribution of micelles in the microemulsions