Propriedades cerâmicas e imobilização do manganês em cerâmica estrutural

In this work is the addition of a metallic ion, of the metal Manganese, in a clay of Rio Grande do Norte state for structural ceramics use, the objective this study was to assess the evolution of ceramic properties. The clay was characterized by Chemical and Thermal analysis and Xray difraction. The metallic ion was added in the clay as aqueous solutions at concentrations of 100, 150 and 200 mg / L. The molded by extrusion and the burned were temperatures at 850, 950, 1050 and 1150 º C. Was made Chemical Analysis and investigated the following parameters environmental and ceramic: Solubility, Colour, Linear Retraction (%), Water Absorption (%), Gresification Curves, Apparent Porosity (%), Apparent Specific Mass (g/cm3) and Flexion Rupture Module (kgf/cm2). The results showed that increasing the concentration of metallic ion, properties such as Apparent Porosity (%), Water Absorption (%) decreases and the Flexion Rupture Module (kgf/cm2) increases with increasing temperature independent of the concentration of the ion. The gresification curves showed that the optimum firing temperatures were in the range between 950 and 1050 ° C. The evaluation of the properties showed that the ceramic material can be studied its use in solid brick and ceramic materials with structural function of filling. The results of solubility showed that the addition of ion offers no risk to the environment

Piroxicam encapsulated in liposomes: Characterization and in vivo evaluation of topical anti-inflammatory effect

Liposomes of soya phosphatidylcholine, cholesterol, and stearylamine (molar ratio 6/3/1) and 0.1% alpha-tocopherol were prepared by the extrusion of multilamellar vesicles through 0.2-mu m polycarbonate membrane. Liposomes were characterized by electron transmission microscopy, and the mean structure diameter was 278 nm. The encapsulation efficiency obtained was 12.73%. The topical anti-inflammatory effect was evaluated in vivo by the cotton pellet granuloma method. We analyzed free piroxicam at 4 mg/kg, piroxicam encapsulated in liposomes added to 1.5% hydroxyethylcellulose (HEC) gel at 1.6 mg/kg, and piroxicam encapsulated in liposomes added to HEC gel at 4 mg/kg; the inhibition of inflammation obtained was 21.1%, 32.8%, and 47.4%, respectively. These results showed that the encapsulation of piroxicam produced an increase of topical anti-inflammatory effect, suggesting that the inhibition of inflammation can be obtained with lower drug concentrations.

Structural analysis of fertilization in the fish Brycon orbignyanus

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Controle profissional de biofilme dentário como estratégia para manutenção da saúde periodontal de pacientes com aparelho ortodôntico fixo: análise comparativa entre diferentes períodos

The presence of fixed orthodontics appliances interfere on sanitation, allowing periodontal diseases to appear, despite the fact patients keep on visiting the dentist every month. This research aims to determine a protocol for the mechanical control of the dental biofilm performed by the professional. A protocol that was able to maintain the periodontal health of the patients under orthodontic treatment with fixed appliances, and in order to do so, it used a non-controlled, randomized and blind clinical essay. The sample involved 40 adolescents who were under the installation of fixed orthodontics appliances and it was divided in three groups, as follows: monthly controlled group (group 1) composed of 11 patients, the quarterly controlled group (group 2) with 16 patients and the semestrial controlled group (group 3) with 13 patients. For data collection, an interview and clinical exams with probing depth measurement, quantity of keratinized mucosa, Gingival Index and the Plaque Index were used. On the initial exam all patients received brushing guidelines as well as the professional control of dental biofilm, with periodontal scaler, Robinson s brush and prophylactic paste. However, Group 1 returned every month for control procedures; Group 2 every three months and Group 3 after six months. The intervention had a six-month duration (for all the three groups), when all the exams were repeated by another examiner who did not know which group each patient was inserted in. Finally, the research concluded that despite the fact there is no statistically significant difference among the three groups, clinically the patients from the monthly group presented a better response to professional control, with less accumulation of dental biofilm and less rate of gingival inflammation. Thus, the mechanical control of the dental biofilm performed by the professional could not avoid gingival increase, characterized by the raise of probing depth measurement, neither the quantity of keratinized mucosa

Qualidade de vida de pacientes com deformidade dentofacial

In the last decade, an increasing number of studies focusing on the impact of oral deformities on quality of life have been published. However, the evaluation of patients at different phases of the treatment has not been performed. Therefore, the purpose of this study was to determine the impact that dentofacial deformities have on patients` quality of life, as well as the influence exerted by social, economic, demographic and orthodontic factors, type and severity of malocclusion. A bicentric study - of the cross-sectional type of repeated panels - involving two cities - Natal and Rio de Janeiro - was carried out. A total of 227 patients participated in the study: 71 patients in the initial phase of the treatment (before any orthosurgical procedure), 115 patients in the pre-surgical (with braces) phase and 41 patients in the postoperative phase. The quality of life was measured using the Orthognatic Quality of Life Questionnnaire - OQLQ, translated and validated into Portuguese. The normative and aesthetic need for treatment was assessed with the Index of Orthodontic Treatment Need (IOTN) and the Dental Aesthetic Index (DAI); the social, economic and demographic factors, the type of service and malocclusion were also assessed. The data were analyzed through χ2/ Fisher`s exact test to seek the association between the nominal categorical variables in the three phases of treatment, Mann Whitney and Kruskal-Wallis test for gauging the existence of significant differences between two and three groups regarding each domain of OQLQ, respectively. For all tests, it was adopted a significance level of 5%. There was a statistically significant difference (p <0.001) in the general scores of OQLQ and in the domains of social aspects, facial aesthetics and oral function, when the "postoperative group" was compared to the "initial" and "orthodontic preparation" groups. Women, single, aged between 31 and 59 and living in Natal had the greatest impact on quality of life among patients in the "orthodontic preparation" group. Only the variable "income" (2 to 3 minimum wages), for the "initial" group, and gender (female) for the "postoperative" group, showed significant association with quality of life. The normative variable IOTN (DHC and AC) showed significant association with the OQLQ for the "initial" group, and the IOTN-AC-auto in the group of orthodontic preparation, being less important to women. We conclude that the ortho-surgical therapy has positive effects on quality of life after orthognathic surgery

Bolton freeware: aplicativo de avaliação de discrepância de massa dentária desenvolvido pelo programa de pós-graduação em odontologia/UFRN

The calculation of tooth mass discrepancy, essential for good planning and a proper orthodontic finishing, when performed manually, besides being laborious, requires considerable time consumption. The aim of this study was to develop and test Bolton Freeware, a software for analysis of the tooth mass discrepancy of Bolton, aiming to minimize the consumption of time in a less onerous way. The digital analysis of the software was done by means of two-dimensional scanning of plaster study models and compared to manual evaluation (gold standard), using 75 pairs of stone plaster study models divided into two groups according to the magnitude of the Curve of Spee (group I from 0 to 2 mm, group II greater than 2 to 3mm). All the models had permanent dentition and were in perfect condition. The manual evaluation was performed with a digital caliper and a calculator, and the time required to perform the analysis for both methods was recorded and compared. In addition, the software was evaluated by orthodontists regarding its use, by means of questionnaires developed specifically for this purpose. Calibration was performed prior to manual analysis, and excellent levels of inter-rater agreement were achieved, with ICC > 0.75 and r > 0.9 for total and anterior proportion. It was observed in the evaluation of error of the digital method that some teeth showed a significant systematic error, being the highest measured at 0.08 mm. The analysis of total tooth mass discrepancy performed by Bolton Freeware, for those cases in which the curve of Spee is mild and moderate, differ from manual analysis, on average, 0.09 mm and 0.07 mm respectively, for each tooth evaluated, with r> 0, 8 for total and anterior proportion. According to the specificity and sensitivity test, Bolton Freeware has an improved ability to detect true negatives, i.e. the presence of discrepancy. The Bolton analysis digitally performed was faster, with an average difference of time consumed to perform the analysis of Bolton between the two methods of approximately 6 minutes. Most experts interviewed (93%) approved the usability of the software

Influência das condições de saúde bucal no desempenho das atividades diárias de adolescentes escolares

Instruments are used in odontology to measure the Quality of Life Related to Oral Health (OHRQoL) to scale how the oral condition interferes with functional areas, of the people s psychological and social life. This cross-sectional study, held in Natal/RN, with 215 students from the Federal Institute of Education, Science and Technology of Rio Grande do Norte (IFRN) has investigated the association between the performance of daily activities and oral health status of school adolescents from 15 to 19 years of age, through the normative index DMFT (permanent teeth decayed, missing and filled), CPI (Community Periodontal Index) and DAI (dental Aesthetic Index) and subjective questionnaire assessment of quality of life related oral health OIDP index (oral impacts on daily performance). It was also carried out the socioeconomic characteristics of students through IFRN own data. Concerning the analysis of data was performed a descriptive analysis of the variables by their absolute and relative frequencies and measures of central tendency. The chi-square test was used to assess the association between the dependent variable and the independent categorical variables and the Student t test for quantitative. It was also conducted a further multiple analysis out using Poisson regression with robust variance between the outcome "presence of impact" and the independent variables that showed p <0.20. It was used for all the statistical tests a significance level of 5%. Among the adolescents surveyed, 51.16% reported that at least one activity assessed by OIDP had hampered its implementation due to some dental problem. The difficulties were more pronounced in the activities of eating (31.6%), oral hygiene (25.6%) and smile (25.1%).The tooth position, followed by toothache, were the causes of the impacts reported by most teenagers. There was a significant association between the presence and impact of the presence of one or more decayed teeth (p = 0.012), the presence of gum bleeding (p = 0.012) and for orthodontic treatment (p = 0.003), independently of other variables. There was no significant association between oral health status and socioeconomic and demographic characteristics of the adolescents. The survey results showed that there is an association between oral health status of the population studied and reports of difficulties in carrying out daily activities evaluated. The worse the oral health status, the greater the impact of this condition on the adolescents quality of life

Influência da laserterapia na proliferação de células-tronco do ligamento periodontal humano

Low level laser irradiation (LLLI) has been used in Dentistry to promote wound healing and tissue regeneration. The literature shows a positive effect of LLLI on cell proliferation, but little is known about their effectiveness in promoting stem cells proliferation. The aim of this study was to evaluate the effect of LLLI on the proliferative rate of human periodontal ligament stem cells. Extracts of periodontal ligament were isolated from two third molars removed by surgical and/or orthodontic indication. After enzymatic digestion, the cells were grown in α-MEM culture medium supplemented with antibiotics and 15% fetal bovine serum. On the third subculture, the cells were irradiated with a InGaAlP-diode laser, using two different energy densities (0,5J/cm 2 - 16 seconds and 1,0J/cm² - 33 seconds), with wavelength of 660nm and output power of 30mW. A new irradiation, using the same parameters, was performed 48h after the first. A control group (non irradiated) was kept under the same experimental culture conditions. The Trypan blue exclusion test and the mitochondrial activity of the cells measured by MTT [3-(4,5-Dimethylthiazol-2-yl)-2,5-Diphenyltetrazolium Bromide] essay were performed to assess the cell proliferation in the intervals of 0, 24, 48 e 72 h after irradiation. The data of cell counts were submitted to nonparametrical statistical tests (Kruskal-Wallis and Mann-Whitney), considering a confidence interval of 95%. DAPI (4 -6-Diamidino-2-phenylindole) staining of the cells was performed at 72h interval to evaluate possible nuclear morphological changes induced by LLLI. The results of this study show that the energy density of 1,0 J/cm² promoted greater cell proliferation compared to the other groups (control and 0,5 J/cm²) at intervals of 48 and 72h. The mitochondrial activity measured by MTT essay showed similar results to the Trypan blue cell counting test. The group irradiated with 1,0J/cm² exhibited a significantly higher MTT activity in the intervals of 48 and 72h, when compared to the group irradiated with 0,5J/cm². No nuclear morphological change was observed in the cells from the three groups studied. It is concluded that LLLI has stimulatory effects on the proliferation of human periodontal ligament stem cells. Therefore, the use of laser irradiation in this cell type may be important to promote future advances in periodontal regeneration

Debris, Roughness and Friction of Stainless Steel Archwires Following Clinical Use

Objective: To investigate the degree of debris, roughness, and friction of stainless steel orthodontic archwires before and after clinical use.Materials and Methods: For eight individuals, two sets of three brackets (n = 16) each were bonded from the first molar to the first premolar. A passive segment of 0.019- x 0.025-inch stainless steel archwire was inserted into the brackets and tied by elastomeric ligature. Debris level (via scanning electron microscopy), roughness, and frictional force were evaluated as-received and after 8 weeks of intraoral exposure. Mann-Whitney, Wilcoxon signed-rank, and Spearman correlation tests were used for statistical analysis at the .05 level of significance.Results: There were significant increases in the level of debris (P = .0004), roughness of orthodontic wires (P = .002), and friction (P = .0001) after intraoral exposure. Significant positive correlations (P < .05) were observed between these three variables.Conclusion: Stainless steel rectangular wires, when exposed to the intraoral environment for 8 weeks, showed a significant increase in the degree of debris and surface roughness, causing an increase in friction between the wire and bracket during the mechanics of sliding. (Angle Orthod. 2010;80:521-527.)

Condicionamento estrutural das zonasa de cisalhamento da região de Forquilha, domínio Ceará Central: uma abordagem integrada de sensoriamento remoto e geologia estrutural

The studied region, named Forquilha and localized in northwestern Central Ceará domain (northern portion of Borborema Province), presents a lithostratigraphic framework constituted by paleoproterozoic metaplutonics, metasedimentary sequences and neoproterozoic granitoids. The metasedimentary rocks of Ceará group occupy most part of the area. This group is subdivided in two distinct units: Canindé and Independência. Canindé unit is represented basically by biotite paragneisses and muscovite paragneisses, with minor metabasic rocks (amphibolite lens). Independência sequence is composed by garnetiferous paragneisses, sillimanite-garnet-quartz-muscovite schists and quartz-muscovite schists, pure or muscovite quartzites and rare marbles. At least three ductile deformation events were recognized in both units of Ceará group, named D1, D2 and D3. The former one is interpreted as related to a low angle tangential tectonics which mass transport is southward. D2 event is marked by the development of close/isoclinal folds with a N-S oriented axis. Refolding patterns generated by F1 and F2 superposition are found in several places. The latest event (D3) corresponds to a transcurrent tectonics, which led to development of mega-folds and several shear zones, under a transpressional regime. The mapped shear zones are Humberto Monte (ZCHM), Poço Cercado (ZCPC) and Forquilha (ZCF). Digital image processing of enhanced Landsat 7-ETM+ satellite images, combined with field data, demonstrate that these penetrative structures are associated with positive and negative geomorphologic patterns, distributed in linear and curvilinear arrangements with tonal banding, corresponding to the ductile fabric and to crests. Diverse color composites were tested and RGB-531 and RGB-752 provided the best results for lineament analysis of the most prominent shear zones. Spatial filtering techniques (3x3 and 5x5 filters) were also used and the application of Prewitt filters generated the best products. The integrated analysis of morphological and textural aspects from filtered images, variation of tonalities related to the distribution of geologic units in color composites and the superposition over a digital elevation model, contributed to a characterization of the structural framework of the study area. Kinematic compatibility of ZCHM, ZCPC, ZCF shear zones, as well as Sobral-Pedro II (ZCSPII) shear zone, situated to the west of the study area, was one of the goal of this work. Two of these shear zones (ZCHM, ZCPC) display sinistral movements, while the others (ZCSPII, ZCF) exhibit dextral kinematics. 40Ar/39Ar ages obtained in this thesis for ZCSPII and ZCPC, associated with other 40Ar/39Ar data of adjacent areas, indicate that all these shear zones are related to Brasiliano orogeny. The trend of the structures, the opposite shear senses and the similar metamorphic conditions are fitted in a model based on the development of conjugate shear zones in an unconfined transpression area. A WNW-ESE bulk shortening direction is infered. The geometry and kinematic of the studied structures suggest that shortening was largely accommodated by lateral extrusion, with only minor amounts of vertical stretch

Produção de biscoitos extrusados de polvilho azedo com fibras: efeito de parâmetros operacionais sobre as propriedades físicas

Neste trabalho buscou-se avaliar o efeito de parâmetros operacionais do processo de extrusão no desenvolvimento de biscoitos de polvilho com fibras, utilizando como matérias-primas o polvilho azedo e o farelo de mandioca. O processamento foi realizado em um extrusor mono-rosca, sendo considerados parâmetros variáveis: temperatura na 3ª zona de extrusão, umidade e porcentagem de fibras na mistura. Para analisar o efeito combinado das variáveis independentes nas características tecnológicas dos extrusados, utilizou-se o delineamento 'central composto rotacional' para três fatores. Os resultados obtidos mostraram efeitos significativos da umidade e porcentagem de fibras sobre o volume específico, sendo que a temperatura afetou os índices de solubilidade e absorção de água dos produtos extrusados. Condições de baixa temperatura (65 °C), baixa umidade (12%) e baixo teor de fibras (<4%), nas condições de processo utilizadas, produzem biscoitos com boas características tecnológicas.

Rapid prototyping and inclined plane technique in the treatment of maxillofacial malformations in a fox

An approximately 9-month-old fox (Pseudalopex ventulus) was presented With malocclusion and deviation of the lower jaw to the right side. Orthodontic treatment was performed using the inclined plane technique. Virtual 3D models and prototypes of the head were based on computed tomography (CT) image data to assist in diagnosis and treatment.

Efeito dos parâmetros de extrusão sobre as propriedades funcionais de extrusados da farinha de batata-doce

Farinha de batata-doce (Ipomoea batatas) foi extrusada em equipamento de rosca simples, mantendo-se fixas as temperaturas na 1ª e 2ª zonas de extrusão (20ºC e 60ºC, respectivamente). O efeito das variáveis umidade da farinha (15, 18 e 21%), temperatura na 3ª zona (100, 120 e 140ºC) e rotação da rosca (180, 210 e 240 rpm) sobre as características dos extrusados foi investigado utilizando-se metodologia de superfície de resposta. O teor de umidade e a temperatura de extrusão influenciaram significativamente a expansão dos extrusados. O índice de expansão apresentou valores crescentes com a temperatura sob baixos teores de umidade. A dureza dos extrusados e também o índice de absorção de água e o índice de solubilidade em água das farinhas extrusadas não mostraram modelo de regressão significativo com as condições de processo. Quanto à cor das farinhas, o componente L* (luminosidade) apresentou valores crescentes e o parâmetro a*, valores decrescentes com a elevação do teor de umidade até 20-21%. O parâmetro b* e a diferença de cor entre farinhas extrusadas e não extrusadas mostraram valores decrescentes com o aumento da umidade.

Desenvolvimento de misturas instantâneas de mandioca e caseína: efeito do teor de proteína e parâmetros de extrusão sobre a viscosidade

O interesse da indústria de alimentos por produtos desenvolvidos a partir de farinhas acrescidas de proteína não se deve somente às suas características nutricionais, senão também às suas propriedades funcionais e reológicas, as quais definem as suas aplicações comerciais. Este trabalho teve por objetivo avaliar o efeito de parâmetros operacionais do processo de extrusão sobre as propriedades de pasta de misturas de farinha de mandioca e caseína. O processo de extrusão seguiu o delineamento 'central composto rotacional' para três fatores: teor de proteína (2,5 a 9,5%), umidade (14,5 a 19,5%) e temperatura de extrusão (65 a 135 ºC). As misturas antes e após a extrusão foram analisadas no Rapid Visco Analyser (RVA) quanto a: viscosidade inicial, pico de viscosidade, quebra de viscosidade, viscosidade final e tendência à retrogradação. Os resultados obtidos nas misturas antes da extrusão mostraram aumento dos valores de viscosidade com o aumento da concentração de proteína até o ponto central (6%) e, nos teores mais elevados de proteína, ocorreu redução destes. Após a extrusão, observou-se que o teor de proteína foi a variável de maior efeito sobre as propriedades de pasta, seguida pela umidade das misturas.

Thermal and pasting properties of cassava starch-dehydrated orange pulp blends

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)