The impact of biofuels for road traffic on air quality : a modelling approach

The selection of the energy source to power the transport sector is one of the main current concerns, not only relative with the energy paradigm but also due to the strong influence of road traffic in urban areas, which highly affects human exposure to air pollutants and human health and quality of life. Due to current important technical limitations of advanced energy sources for transportation purposes, biofuels are seen as an alternative way to power the world’s motor vehicles in a near-future, helping to reduce GHG emissions while at the same time stimulating rural development. Motivated by European strategies, Portugal, has been betting on biofuels to meet the Directive 2009/28/CE goals for road transports using biofuels, especially biodiesel, even though, there is unawareness regarding its impacts on air quality. In this sense, this work intends to clarify this issue by trying to answer the following question: can biodiesel use contribute to a better air quality over Portugal, particularly over urban areas? The first step of this work consisted on the characterization of the national biodiesel supply chain, which allows verifying that the biodiesel chain has problems of sustainability as it depends on raw materials importation, therefore not contributing to reduce the external energy dependence. Next, atmospheric pollutant emissions and air quality impacts associated to the biodiesel use on road transports were assessed, over Portugal and in particular over the Porto urban area, making use of the WRF-EURAD mesoscale numerical modelling system. For that, two emission scenarios were defined: a reference situation without biodiesel use and a scenario reflecting the use of a B20 fuel. Through the comparison of both scenarios, it was verified that the use of B20 fuels helps in controlling air pollution, promoting reductions on PM10, PM2.5, CO and total NMVOC concentrations. It was also verified that NO2 concentrations decrease over the mainland Portugal, but increase in the Porto urban area, as well as formaldehyde, acetaldehyde and acrolein emissions in the both case studies. However, the use of pure diesel is more injurious for human health due to its dominant VOC which have higher chronic hazard quotients and hazard indices when compared to B20.

Metabolic signature of lung cancer: a metabolomic study of human tissues and biofluids

This thesis reports the application of metabolomics to human tissues and biofluids (blood plasma and urine) to unveil the metabolic signature of primary lung cancer. In Chapter 1, a brief introduction on lung cancer epidemiology and pathogenesis, together with a review of the main metabolic dysregulations known to be associated with cancer, is presented. The metabolomics approach is also described, addressing the analytical and statistical methods employed, as well as the current state of the art on its application to clinical lung cancer studies. Chapter 2 provides the experimental details of this work, in regard to the subjects enrolled, sample collection and analysis, and data processing. In Chapter 3, the metabolic characterization of intact lung tissues (from 56 patients) by proton High Resolution Magic Angle Spinning (HRMAS) Nuclear Magnetic Resonance (NMR) spectroscopy is described. After careful assessment of acquisition conditions and thorough spectral assignment (over 50 metabolites identified), the metabolic profiles of tumour and adjacent control tissues were compared through multivariate analysis. The two tissue classes could be discriminated with 97% accuracy, with 13 metabolites significantly accounting for this discrimination: glucose and acetate (depleted in tumours), together with lactate, alanine, glutamate, GSH, taurine, creatine, phosphocholine, glycerophosphocholine, phosphoethanolamine, uracil nucleotides and peptides (increased in tumours). Some of these variations corroborated typical features of cancer metabolism (e.g., upregulated glycolysis and glutaminolysis), while others suggested less known pathways (e.g., antioxidant protection, protein degradation) to play important roles. Another major and novel finding described in this chapter was the dependence of this metabolic signature on tumour histological subtype. While main alterations in adenocarcinomas (AdC) related to phospholipid and protein metabolisms, squamous cell carcinomas (SqCC) were found to have stronger glycolytic and glutaminolytic profiles, making it possible to build a valid classification model to discriminate these two subtypes. Chapter 4 reports the NMR metabolomic study of blood plasma from over 100 patients and near 100 healthy controls, the multivariate model built having afforded a classification rate of 87%. The two groups were found to differ significantly in the levels of lactate, pyruvate, acetoacetate, LDL+VLDL lipoproteins and glycoproteins (increased in patients), together with glutamine, histidine, valine, methanol, HDL lipoproteins and two unassigned compounds (decreased in patients). Interestingly, these variations were detected from initial disease stages and the magnitude of some of them depended on the histological type, although not allowing AdC vs. SqCC discrimination. Moreover, it is shown in this chapter that age mismatch between control and cancer groups could not be ruled out as a possible confounding factor, and exploratory external validation afforded a classification rate of 85%. The NMR profiling of urine from lung cancer patients and healthy controls is presented in Chapter 5. Compared to plasma, the classification model built with urinary profiles resulted in a superior classification rate (97%). After careful assessment of possible bias from gender, age and smoking habits, a set of 19 metabolites was proposed to be cancer-related (out of which 3 were unknowns and 6 were partially identified as N-acetylated metabolites). As for plasma, these variations were detected regardless of disease stage and showed some dependency on histological subtype, the AdC vs. SqCC model built showing modest predictive power. In addition, preliminary external validation of the urine-based classification model afforded 100% sensitivity and 90% specificity, which are exciting results in terms of potential for future clinical application. Chapter 6 describes the analysis of urine from a subset of patients by a different profiling technique, namely, Ultra-Performance Liquid Chromatography coupled to Mass Spectrometry (UPLC-MS). Although the identification of discriminant metabolites was very limited, multivariate models showed high classification rate and predictive power, thus reinforcing the value of urine in the context of lung cancer diagnosis. Finally, the main conclusions of this thesis are presented in Chapter 7, highlighting the potential of integrated metabolomics of tissues and biofluids to improve current understanding of lung cancer altered metabolism and to reveal new marker profiles with diagnostic value.

Estudo de defeitos em filmes finos de ZnO depositados por Rf-sputtering

Neste trabalho foram estudados diferentes filmes finos de ZnO depositados por Rf-Sputtering. Filmes finos de ZnO com diferentes propriedades óticas foram obtidos intencionalmente variando os parâmetros de deposição. De modo a correlacionar as propriedades óticas e estruturais com os parâmetros de deposição, foram utilizadas diferentes técnicas de caracterização avançadas, tais como, fotoluminescência, microscopia de força atómica, difração de raios- X e retrodispersão de Rutherford. Este trabalho centra-se na discussão e análise das bandas de emissão vermelha, verde e azul, comumente observadas em amostras de ZnO e cuja natureza tem sido objeto de grande controvérsia na literatura. A utilização de técnicas de caracterização estrutural revelou-se de extrema importância para correlacionar as propriedades físicas de composição e estrutura com os centros óticos observados nos filmes. Nesta base, foram propostos e discutidos diferentes modelos de recombinação ótica associados à qualidade estrutural dos filmes, considerando modelos de camadas que descrevem a heterogeneidade lateral e em profundidade. Desta análise verificou-se a presença de heterogeneidade estrutural e composicional, que aumenta a complexidade na compreensão da correlação dos parâmetros de deposição com as propriedades óticas dos filmes. Foi discutida a limitação e validade de diferentes modelos tendo em conta a presença da heterogeneidade existente nos filmes estudados. Este trabalho contribui assim para uma melhor compreensão da complexidade de interação dos diferentes defeitos e o seu efeito nas propriedades óticas, nomeadamente o papel dos defeitos de interface, na superfície, nas fronteiras de grão e junto ao substrato.

Novel hardware and software combination for automotive motorsport vehicles based on direct processing of graphical functions

The main motivation for the work presented here began with previously conducted experiments with a programming concept at the time named "Macro". These experiments led to the conviction that it would be possible to build a system of engine control from scratch, which could eliminate many of the current problems of engine management systems in a direct and intrinsic way. It was also hoped that it would minimize the full range of software and hardware needed to make a final and fully functional system. Initially, this paper proposes to make a comprehensive survey of the state of the art in the specific area of software and corresponding hardware of automotive tools and automotive ECUs. Problems arising from such software will be identified, and it will be clear that practically all of these problems stem directly or indirectly from the fact that we continue to make comprehensive use of extremely long and complex "tool chains". Similarly, in the hardware, it will be argued that the problems stem from the extreme complexity and inter-dependency inside processor architectures. The conclusions are presented through an extensive list of "pitfalls" which will be thoroughly enumerated, identified and characterized. Solutions will also be proposed for the various current issues and for the implementation of these same solutions. All this final work will be part of a "proof-of-concept" system called "ECU2010". The central element of this system is the before mentioned "Macro" concept, which is an graphical block representing one of many operations required in a automotive system having arithmetic, logic, filtering, integration, multiplexing functions among others. The end result of the proposed work is a single tool, fully integrated, enabling the development and management of the entire system in one simple visual interface. Part of the presented result relies on a hardware platform fully adapted to the software, as well as enabling high flexibility and scalability in addition to using exactly the same technology for ECU, data logger and peripherals alike. Current systems rely on a mostly evolutionary path, only allowing online calibration of parameters, but never the online alteration of their own automotive functionality algorithms. By contrast, the system developed and described in this thesis had the advantage of following a "clean-slate" approach, whereby everything could be rethought globally. In the end, out of all the system characteristics, "LIVE-Prototyping" is the most relevant feature, allowing the adjustment of automotive algorithms (eg. Injection, ignition, lambda control, etc.) 100% online, keeping the engine constantly working, without ever having to stop or reboot to make such changes. This consequently eliminates any "turnaround delay" typically present in current automotive systems, thereby enhancing the efficiency and handling of such systems.

Avaliação da vulnerabilidade sísmica de edifícios escolares

A grande motivação para este trabalho resultou na avaliação da vulnerabilidade sísmica das escolas básicas e secundárias que fazem parte integrante do parque escolar de Portugal Continental. Apesar de até ao momento apenas se terem estudado a vulnerabilidade de algumas escolas em algumas zonas particulares do nosso país, para este trabalho de investigação tivemos uma ambição muito maior e obviamente fizemos um esforço muito maior. Estabelecemos assim como meta, a avaliação de todo o parque escolar. Embora todo o parque escolar possua na ordem das três centenas de escolas em todo o território nacional e sendo este projeto de reabilitação, um projeto com a duração de 2007 a 2015. Em 2011, por motivos da crise económica, todo o projeto congelou sendo reabilitadas até à data cerca de apenas um terço das escolas. Esta quantidade foi o número de escolas que avaliamos em todo o país. As escolas, sendo edifícios públicos com uma importância fundamental, tanto pela elevada concentração de jovens, como pela função essencial como centros de aprendizagem para as gerações vindouras, como também pela ameaça que representam na eventualidade dum cenário sísmico pela enorme densidade de utilizadores, e pela vantagem de nesse cenário de catástrofe a importância estrutural ser superior em relação à maior parte dos edifícios correntes, devidamente demonstrado pelos argumentos enumerados, consequentemente as escolas podem servir como instalações de proteção civil perante uma catástrofe sísmica para apoio das populações circundantes afetadas. Portanto para cada uma das escolas cordialmente fornecidas pelo Parque Escolar, E.P.E., foi feito um estudo exaustivo e muito individual de cada uma das escolas, onde cada análise foi desenvolvida por uma metodologia simplificada, sendo cada análise sempre individual, e nunca tendo sida aplicada em série, este fator melhora substancialmente a eficácia da avaliação para a quantificação das vulnerabilidades e da determinação do grau de dano e das frações de perda para os requisitos fundamentais de limitação de danos, de não colapso, e de colapso iminente que correspondem a ações com períodos de retorno de 95, 475 e 975 anos. Este trabalho é fundamental para as entidades competentes terem a consciência da vulnerabilidade das escolas secundárias, para puderem atuar a nível estrutural e diminuir assim a vulnerabilidade sísmica, e mesmo que por impossibilidade económica o poder governamental não intervenha, então pode e principalmente deve, elaborar planos de emergência tanto com engenheiros civis qualificados como com a total colaboração das corporações de bombeiros que fazem parte das forças de operação e socorro da Autoridade Nacional de Proteção Civil (ANPC).

Structural characterization and biological activity of polysaccharides from infusions used in the popular tradition

The use of plants with medicinal purposes is an ancient practice still very common in developing regions, and is rapidly spreading in industrialized countries. This fact is evidenced by the large number of ethnobotanical studies found in the literature referring that these plants are often used as decoctions and infusions. In most studies the reported biological activities are attributed to the presence of phenolic compounds, due to their antioxidant properties, and to polysaccharides, with its anti-tumoral properties. In “Trás-os-Montes” region, some of the most popular infusions used by the popular medicine are prepared with the dried leaves of Fraxinus angustifolia, the dried shoots of Mentha suaveolens, and the dried inflorescences of Pterospartum tridentatum. However, there are no studies about the polysaccharides present in these infusions. Thus, through the structural characterization of the polysaccharides present in the infusions of F. angustifolia, M. suaveolens, and P. tridentatum, the present PhD thesis intends to evaluate the possible relation between polysaccharides and the immunostimulatory activity that these infusions might present. In a preliminary phase, infusions of F. angustifolia were prepared according to the popular tradition, and it was observed that the obtained water soluble material contained approximately 85% of material non-retained in C18 cartridges, with hydrophilic characteristics, with the remaining 15% comprising retained-material with hydrophobic characteristics. It was also shown that the infusions only contained between 2 and 4% of high molecular weight material (HMWM), which comprised approximately 30% of carbohydrate material. Sugar and methylation analysis of the HMWM suggested the presence of pectic polysaccharides, together with type II arabinogalactans, mannans, and xyloglucans. However, the amount of material obtained is to low for the fractionation, and structural analysis of the polysaccharides present. The 4 h decoction, divided in two periods of 2 h, with water renewal, allowed to increase the HMWM yield, relatively to the infusions traditional infusions. It was also observed that the decoction also allowed to increase the HMWM proportion of carbohydrate material, due to an increase in the proportion of uronic acid present, although the neutral sugar residues seemed to be detected in similar proportions. Therefore, in all the experiments subsequently performed, the HMWM used was obtained through the decoction of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences. x After the fractionation, through ethanol precipitation, and anion exchange chromatography, of the polysaccharides from the HMWM obtained by the decoction of the vegetable material of the distinct studied plants, it was observed the presence of high proportions of pectic polysaccharides, containing type I arabinogalactans, together with minor proportions of type II arabinogalactans, mannans, and xyloglucans. The presence of pectic polysaccharides in the extracts from F. angustifolia was also evidenced through endo-polygalacturonase treatment, and ESI-MS and ESI-MS/MS experiments. The detection of linked pentose and uronic acid residues, also seemed to suggest the presence of xylogalacturonan domains in the pectic polysaccharides from F. angustifolia. The extracts from F. angustifolia dried leaves also contained type II arabinogalactans that exhibited a higher structural diversity than those detected in the M. suaveolens, and P. tridentatum extracts, particularly in the substitution degree of the galactan backbone, and in the extension of the (1→5)-Araf side chains. Moreover, for all the plants studied, it was also observed that the type II arabinogalactans, extracted during the 2nd 2h of the extraction process, exhibited a substitution degree of the galactan backbone higher than those extracted during the 1st 2h. The extracts from P. tridentatum dried inflorescences contained higher proportions of mannans, and also of xyloglucans, both presenting a substitution degree higher than those, which were detected in lower proportion in the extracts of F. angustifolia and M. suaveolens. Through ESI-MS and ESI-MS/MS it was possible to evidence that the mannans present in the extracts of P. tridentatum presented acetyl groups on the O-2 of the mannosyl residues. It was also evidenced that the P. tridentatum mannans were more extensively acetylated than the mannans detected in the coffee infusion, LBG, and other non-conventional mannan sources. Moreover, it was detected the presence of oligosaccharides comprising hexose residues linked to non acetylated pentose residues, suggesting the possible presence of arabinose residues in the mannans from P. tridentatum extracts. The immunostimulatory activity of three fractions isolated from the extracts of F. angustifolia, M. suaveolens, and P. tridentatum, was tested and an increase in the NO production by macrophages, without compromising their cellular viability, was observed. The type I, and type II arabinogalactans detected in the extracts from F. angustifolia, and M. suaveolens seem to have contributed for the observed immunostimulatory activity. For the fraction from P. tridentatum, the mannans acetylation, and the presence of type I, and type II arabinogalactans seemed to contribute for the macrophage immunostimulatory activity observed. The possible presence of storage xyloglucans from the inflorescences seeds, also seems to have contributed for the immunostimulatory activity registered when the macrophages were stimulated with higher extract concentrations. The results obtained allow to conclude that the extracts of F. angustifolia dried leaves, M. suaveolens dried shoots, and P. tridentatum dried inflorescences contained high proportions of pectic polysaccharides, exhibiting type I arabinogalactans, together with other polysaccharides, such as type II arabinogalactans, mannans, and xyloglucans. This polysaccharide mixture seems to have contributed to the immunostimulatory activity of fractions isolated from the extracts of the studied plants. Therefore, as the same type of polysaccharides seem to be present in the decoctions and in the infusions, it seems possible that the polysaccharides might contribute for the therapeutic properties frequently associated by the popular tradition to the infusions of these plants.

Understanding and modelling hydrological and soil erosion processes in burnt forest catchments

Forest fires implications in overland flow and soil erosion have been researched for several years. Therefore, is widely known that fires enhance hydrological and geomorphological activity worldwide as also in Mediterranean areas. Soil burn severity has been widely used to describe the impacts of fire on soils, and has being recognized as a decisive factor controlling post-fire erosion rates. However, there is no unique definition of the term and the relationship between soil burn severity and post-fire hydrological and erosion response has not yet been fully established. Few studies have assessed post-fire erosion over multiple years, and the authors are aware of none which assess runoff. Small amount of studies concerning pre-fire management practices were also found. In the case of soil erosion models, the Revised Universal Soil Loss Equation (RUSLE) and the revised Morgan–Morgan–Finney (MMF) are well-known models, but not much information is available as regards their suitability in predicting post-fire soil erosion in forest soils. The lack of information is even more pronounced as regards post-fire rehabilitation treatments. The aim of the thesis was to perform an extensive research under the post fire hydrologic and erosive response subject. By understanding the effect of burn severity in ecosystems and its implications regarding post fire hydrological and erosive responses worldwide. Test the effect of different pre-fire land management practices (unplowed, downslope plowed and contour plowed) and time-since-fire, in the post fire hydrological and erosive response, between the two most common land uses in Portugal (pine and eucalypt). Assess the performance of two widely-known erosion models (RUSLE and Revised MMF), to predict soil erosion rates during first year following two wildfires of distinctive burn severity. Furthermore, to apply these two models considering different post-fire rehabilitation treatments in an area severely affected by fire. Improve model estimations of post-fire runoff and erosion rates in two different land uses (pine and eucalypt) using the revised MMF. To assess these improvements by comparing estimations and measurements of runoff and erosion, in two recently burned sites, as also with their post fire rehabilitation treatments. Model modifications involved: (1) focusing on intra-annual changes in parameters to incorporate seasonal differences in runoff and erosion; and (2) inclusion of soil water repellency in runoff predictions. Additionally, validate these improvements with the application of the model to other pine and eucalypt sites in Central Portugal. The review and meta-analysis showed that fire occurrence had a significant effect on the hydrological and erosive response. However, this effect was only significantly higher with increasing soil burn severity for inter-rill erosion, and not for runoff. This study furthermore highlighted the incoherencies between existing burn severity classifications, and proposed an unambiguous classification. In the case of the erosion plots with natural rainfall, land use factor affected annual runoff while land management affected both annual runoff and erosion amounts significantly. Time-since-fire had an important effect in erosion amounts among unplowed sites, while for eucalypt sites time affected both annual runoff and erosion amounts. At all studied sites runoff coefficients increase over the four years of monitoring. In the other hand, sediment concentration in the runoff, recorded a decrease during the same period. Reasons for divergence from the classic post-fire recovery model were also explored. Short fire recurrence intervals and forest management practices are viewed as the main reasons for the observed severe and continuing soil degradation. The revised MMF model presented reasonable accuracy in the predictions while the RUSLE clearly overestimated the observed erosion rates. After improvements: the revised model was able to predict first-year post-fire plot-scale runoff and erosion rates for both forest types, these predictions were improved both by the seasonal changes in the model parameters; and by considering the effect of soil water repellency on the runoff, individual seasonal predictions were considered accurate, and the inclusion of the soil water repellency in the model also improved the model at this base. The revised MMF model proved capable of providing a simple set of criteria for management decisions about runoff and erosion mitigation measures in burned areas. The erosion predictions at the validation sites attested both to the robustness of the model and of the calibration parameters, suggesting a potential wider application.

4-Quinolonas: novos métodos de síntese e transformação em acridonas

A presente dissertação é constituída por quatro capítulos, organizados em introdução geral, discussão do trabalho desenvolvido na síntese de quinolin-4(1H)-onas e acridonas, caracterização estrutural dos novos compostos sintetizados e parte experimental. No primeiro capítulo desta dissertação é apresentada uma breve revisão bibliográfica de quinolin-4(1H)-onas e acridonas, abrangendo a respectiva nomenclatura, ocorrência natural e métodos de síntese. O segundo capítulo engloba estudos da reactividade de (E)-2-estirilquinolin-4(1H)-onas e (E)-N-(2-acetilfenil)-3-arilacrilamidas como dienófilos com o-benzoquinodimetanos, gerados in situ a partir da extrusão quelotrópica do dióxido de enxofre de 2,2-dióxidos de 1,3-di-hidrobenzo[c]tiofenos. Estes estudos conduziram à obtenção de novas 2-(3-aril-1,2,3,4-tetra-hidronaftalen-2-il)-1-metilquinolin-4(1H)-onas e análogos não substituídos no átomo de azoto N1 da quinolin-4(1H)-ona. Em seguida foram estudadas as reações de desidrogenação e fotociclização dos compostos obtidos anteriormente, com vista à obtenção de novas 2-(3-arilnaftalen-2-il)-1-metilquinolin-4(1H)-onas, análogos não substituídos em N1 e de novas acridonas. No segundo capítulo também é abordada a síntese dos compostos precursores, as (E)-N-(2-acetilfenil)-3-arilacrilamidas, as (E)-2-estirilquinolin-4(1H)-onas e os 2,2-dióxidos de 1,3-di-hidrobenzo[c]tiofenos. No terceiro capitulo é discutida a caracterização estrutural das novas quinolin-4(1H)-onas e acridona sintetizadas, com estudos de espetroscopia de ressonância magnética nuclear 1D (1H e 13C) e 2D (homo- e heteronuclear). O quarto capítulo inclui toda a parte experimental, contendo os procedimentos optimizados para a síntese e purificação destes compostos, e a caracterização estrutural dos novos compostos sintetizados.

Pathways of oxidative degradation of wine

The production of color/flavor compounds in wine is the result of different interrelated mechanism reactions. Among these, the oxidation phenomenon and the Maillard reaction stands out with particular relevance due to their large impact on the sensory quality of wines and consequently on the product shelflife. The aim of this thesis is to achieve a global vision of wine degradation mechanisms. The identification of mediators’ reactions involved in oxidative browning and aromatic degradation will be attempted based on different detectors. Two approaches are implemented in this work: a “non-target” approach by which relevant analytical tools will be used to merge the information of cyclic voltammetry and Diode-Array (DAD) detectors, allowing a broader overview of the system and the note of interesting compounds, and a “target” approach by which the identification and quantification of the different compounds related to the wine degradation process will be performed using different detectors (HPLC-UV/Vis, LC-MS, GC-MS, and FID). Two different patterns of degradation will be used in this study: wines generated by O2 and temperature perturbations, and synthetic solutions with relevant wine constituents for mechanisms validation. Results clearly demonstrate a “convolution” of chemical mechanisms. The presence of oxygen combined with temperature had a synergistic effect on the formation of several key odorant compounds.The results of this work could be translated to the wine-making and wine-storage environment from the modelling of the analysed compounds.

Avanços metodológicos na síntese de novos derivados de flavonas

As estirilflavonas poli-hidroxiladas são compostos heterocíclicos de natureza polifenólica que suscitam interesse devido à atividade biológica que possuem atuando, por exemplo, como antioxidantes. O desenvolvimento de novas rotas de síntese de estirilflavonas constitui um desafio e é neste contexto que se têm efetuado vários estudos sobre a aplicação de reações de acoplamento cruzado catalisadas por paládio, como a reação de Heck, na preparação deste tipo de compostos. Nesta dissertação reporta-se a síntese de (E)-8-estirilflavonas através da reação de Heck de 8-iodoflavonas com derivados de estireno com rendimentos excelentes, descrevendo-se um estudo no qual se optimizaram as condições experimentais desta reação. Adicionalmente, descrevem-se duas tentativas de desmetilação da (E)-8-[2-(4-metoxifenil)vinil]-4’,5,7-trimetoxiflavona. As 8- iodoflavonas foram preparadas com elevada regiosseletividade através da ciclização oxidativa/iodação das (E)-2’-hidroxicalconas correspondentes por aplicação do sistema de reagentes I2/DMSO. A propósito, descreve-se um estudo de ciclização oxidativa/iodação da (E)-2’-hidroxi-4,4’,6’- trimetoxicalcona, no qual se testou a aplicação do sistema de reagentes I2/DMSO na síntese de iodoflavonas em reações one-pot. As (E)-2’- hidroxicalconas foram sintetizadas através da condensação aldólica catalisada por base entre a 2’-hidroxi-4’,6’-dimetoxiacetofenona, previamente preparada, e derivados de benzaldeído. A caraterização estrutural da maioria dos compostos obtidos neste trabalho foi efetuada com base em estudos de espetroscopia de ressonância magnética nuclear (RMN), nomeadamente de 1H e 13C, e, sempre que possível, em estudos bidimensionais de correlação espetroscópica heteronuclear (HSQC e HMBC), bem como em estudos de espetrometria de massa (EM).

Regional and urban air quality modelling under a climate change scenario

The better understanding of the interactions between climate change and air quality is an emerging priority for research and policy. Climate change will bring changes in the climate system, which will affect the concentration and dispersion of air pollutants. The main objective of the current study is to assess the impacts of climate change on air quality in 2050 over Portugal and Porto urban area. First, an evaluation and characterization of the air quality over mainland Portugal was performed for the period between 2002 and 2012. The results show that NO2, PM10 and O3 are the critical pollutants in Portugal. Also, the influence of meteorology on O3, NO2 and PM10 levels was investigate in the national main urban areas (Porto and Lisboa) and was verified that O3 has a statistically significant relationship with temperature in most of the components. The results also indicate that emission control strategies are primary regulators for NO2 and PM10 levels. After, understanding the national air quality problems and the influence that meteorology had in the historical air quality levels, the air quality modelling system WRF-CAMx was tested and the required inputs for the simulations were prepared to fulfil the main goal of this work. For the required air quality modelling inputs, an Emission Projections under RCP scenarios (EmiPro-RCP) model was developed to assist the estimation of future emission inventories for GHG and common air pollutants. Also, the current emissions were estimated for Portugal with a higher detailed disaggregation to improve the performance of the air quality simulations. The air quality modelling system WRF/CAMx was tested and evaluated over Portugal and Porto urban area and the results point out that is an adequate tool for the analysis of air quality under climate change. For this purpose, regional simulations of air quality during historical period and future (2045-2050) were conducted with CAMx version 6.0 to evaluate the impacts of simulated future climate and anthropogenic emission projections on air quality over the study area. The climate and the emission projections were produced under the RCP8.5 scenario. The results from the simulations point out, that if the anthropogenic emissions keep the same in 2050, the concentrations of NO2, PM10 and O3 will increase in Portugal. When, besides the climate change effects, is consider the projected anthropogenic emissions the annual mean concentrations of NO2 decrease significantly in Portugal and Porto urban area, and on the contrary the annual mean PM10 concentrations increases in Portugal and decrease in Porto urban area. The O3 results are mainly caused by the reduction of ozone precursors, getting the higher reductions in urban areas and increases in the surrounding areas. All the analysis performed for both simulations for Porto urban area support that, for PM10 and O3, there will be an increase in the occurrence of extreme values, surpassing the annual legislated parameters and having more daily exceedances. This study constitutes an innovative scientific tool to help in future air quality management in order to mitigate future climate change impacts on air quality.

Niobium oxides and niobates physical properties

Niobium oxides have been pointed as an alternative to tantalum in the production of solid electrolytic capacitors, with advantages regarding the dielectric constant, density and price. In this work, it is intended to create a new family of niobium oxides based capacitors, adapting the technology and production line currently used with tantalum. Despite the known potentialities of niobium oxides, and many types of niobates, in several technological applications, the understanding of these oxide systems is still noticeably insufficient. Hence, a careful bibliographic review is shown, which evidences the complexity of these materials, the difficulty in identifying of their different phases and polymorphs, as well as in the interpretation of their properties. In this context, several fundamental studies on niobium oxides are presented, namely structural, microstructural, optical and electrical characterizations, which allow not only to contribute in an important way for the general knowledge of the physical properties of these materials, but also to advance to a sustained development of the niobium oxides based solid electrolytic capacitors. Several processing parameters were studied, clearing the way towards the creation of a prototype. It was also decided to perform a preliminary study on the synthesis and characterization of other oxide systems based in niobium, namely rare-earth orthoniobates (RENbO4), which interest has been related to their optical properties and protonic conductivity. Hence, single and polycrystalline samples of RENbO4 were synthesized and characterized structural, optical and electrically, leaving open an interesting future work.

A computational study of ionic liquids used in the production of fuels and biofuels

For the past decades it has been a worldwide concern to reduce the emission of harmful gases released during the combustion of fossil fuels. This goal has been addressed through the reduction of sulfur-containing compounds, and the replacement of fossil fuels by biofuels, such as bioethanol, produced in large scale from biomass. For this purpose, a new class of solvents, the Ionic Liquids (ILs), has been applied, aiming at developing new processes and replacing common organic solvents in the current processes. ILs can be composed by a large number of different combinations of cations and anions, which confer unique but desired properties to ILs. The ability of fine-tuning the properties of ILs to meet the requirements of a specific application range by mixing different cations and anions arises as the most relevant aspect for rendering ILs so attractive to researchers. Nonetheless, due to the huge number of possible combinations between the ions it is required the use of cheap predictive approaches for anticipating how they will act in a given situation. Molecular dynamics (MD) simulation is a statistical mechanics computational approach, based on Newton’s equations of motion, which can be used to study macroscopic systems at the atomic level, through the prediction of their properties, and other structural information. In the case of ILs, MD simulations have been extensively applied. The slow dynamics associated to ILs constitutes a challenge for their correct description that requires improvements and developments of existent force fields, as well as larger computational efforts (longer times of simulation). The present document reports studies based on MD simulations devoted to disclose the mechanisms of interaction established by ILs in systems representative of fuel and biofuels streams, and at biomass pre-treatment process. Hence, MD simulations were used to evaluate different systems composed of ILs and thiophene, benzene, water, ethanol and also glucose molecules. For the latter molecules, it was carried out a study aiming to ascertain the performance of a recently proposed force field (GROMOS 56ACARBO) to reproduce the dynamic behavior of such molecules in aqueous solution. The results here reported reveal that the interactions established by ILs are dependent on the individual characteristics of each IL. Generally, the polar character of ILs is deterministic in their propensity to interact with the other molecules. Although it is unquestionable the advantage of using MD simulations, it is necessary to recognize the need for improvements and developments of force fields, not only for a successful description of ILs, but also for other relevant compounds such as the carbohydrates.

Oxidation and glycoxidation of phosphatidylserine and their effect in immune response : a lipidomic approach

Phosphatidylserine (PS) is a member of the class of phospholipids, and is distributed among all cells of mammalians, playing important roles in diverse biological processes, including blood clotting and apoptosis. When externalized, PS is a ligand that is recognized on apoptotic cells. It has been considered that before externalization PS is oxidized and oxPS enhance the recognition by macrophages receptors, however the knowledge about oxidation of PS is still limited. PS, like others phospholipids, has two fatty acyl chains and one polar head group, in this case is the amino acid serine. The modifications in PS structure can occur by oxidation of the unsaturated fatty acyl chains and by glycation of the polar head group, due to free amine group, thus increasing the susceptibility to oxidative events. The main goal of this work was to characterize and identify oxidized and glycoxidized PS, contributing to the knowledge of the biological role of oxidation products of PS, as well as of glycated PS, in immune and inflammatory processes. To achieve this goal, PS standards (1-palmitoyl-2-oleoyl-sn-glycero-3-phospho- L-serine (POPS), 1,2-dipalmitoyl-sn-glycero-3-phospho-L-serine (DPPS), 1- palmitoyl-2-linoleoyl-sn-glycero-3-phospho-L-serine (PLPS) and 1-palmitoyl-2- arachidonoyl-sn-glycero-3-phospho-L-serine (PAPS)) and glycated PS (PAPS and POPS) were induced to oxidize in model systems, using different oxidant reagents: HO• and 2,2'-azobis-2-methyl-propanimidamide dihydrochloride (AAPH) . The detailed structural characterization of the oxidative products was performed by ESI-MS and MS/MS coupled to separation techniques such as off line TLC-MS and on line LC-MS, in order to obtained better characterization of the larger number of PS and glycated PS oxidation products. The results obtained in this work allowed to identify several oxidation products of PS and glycated PS with modifications in unsaturated fatty acyl chain. Also, oxidation products formed due to structural changes in the serine polar head with formation of terminal acetamide, terminal hydroperoxyacetaldehyde.and terminal acetic acid (glycerophosphacetic acid, GPAA) were identified. The mass spectrometric specific fragmentation pathway of each type of oxidation product was determined using different mass spectrometry approaches. Based on the identified fragmentation pathways, targeted lipidomic analysis was performed to detect oxidation products modified in serine polar head in HaCaT cell line treated with AAPH. The GPAA was detected in HaCaT cells treated with AAPH to induce oxidative stress, thus confirming that modifications in PS polar head is possible to occur in biological systems. Furthermore, it was found that glycated PS species are more prone to oxidative modifications when compared with non glycated PS. During oxidation of glycated PS, besides the oxidation in acyl chains, new oxidation products due to oxidation of the glucose moiety were identified, including PS advanced glycation end products (PSAGES). To investigate if UVA oxidative stress exerted changes in the lipidome of melanoma cell lines, particularly in PS profile, a lipidomic analysis was performed. The lipid profile was obtained using HILIC-LC-MS and GC-MS analysis of the total lipid extracts obtained from human melanoma cell line (SKMEL- 28) after UVA irradiation at 0, 2 and 24 hours. The results did not showed significant differences in PS content. At molecular level, only PS (18:0:18:1) decreased at the moment of irradiation. The most significant changes in phospholipids content occurred in phosphatidylcholines (PC) and phosphatidylinositol (PI) classes, with an increase of mono-unsaturated fatty acid (MUFA), similarly as observed for the fatty acid analysis. Overall, these data indicate that the observed membrane lipid changes associated with lipogenesis after UVA exposure may be correlated with malignant transformations associated with cancer development and progression. Despite of UVA radiation is associated with oxidative damage, in this work was not possible observe oxidation phospholipids. The anti/pro-inflammatory properties of the oxidized PLPS (oxPLPS) versus non-oxidized PLPS were tested on LPS stimulated RAW 264.7 macrophages. The modulation of intracellular signaling pathways such as NF-kB and MAPK cascades by oxPLPS and PS was also examined in this study. The results obtained from evaluation of anti/pro-inflammatory properties showed that neither PLPS or oxPLPS species activated the macrophages. Moreover only oxidized PLS were found to significantly inhibit NO production and iNOS and il1β gene transcription induced by LPS. The analysis at molecular level showed that this was the result of the attenuation of LPS-induced c-Jun-N-terminal kinase (JNK) and p65 NF-kB nuclear translocation. Overall these data suggest that oxPLPS, but not native PLPS, mitigates pro-inflammatory signaling in macrophages, contributing to containment of inflammation during apoptotic cell engulfment. The results obtained in this work provides new information on the modifications of PS, facilitating the identification of oxidized species in complex samples, namely under physiopathologic conditions and also contributes to a better understanding of the role of oxPS and PS in the inflammatory response, in the apoptotic process and other biological functions.

Design e desenvolvimento de equipamentos de iluminação técnica

Este documento é uma sinopse das atividades desenvolvidas e, conhecimentos adquiridos ao longo do estágio na empresa Lightenjin, Sistemas de Iluminação, Lda. e, surge em forma de relatório de projeto. O primeiro projeto foi o desenvolvimento de uma família de candeeiros. O segundo e principal projeto foi a criação e desenvolvimento de um projetor para aplicação em calha eletrificada, com as devidas restrições do Project brief apresentado pela empresa. O terceiro projeto foi o desenvolvimento de um projetor Downlight de encastrar. Houve outras tarefas ligadas à modelação de componentes, desenhos técnicos, manuais de instruções, fichas técnicas e prototipagem rápida. Em todos os projetos foi utilizada a metodologia de trabalho apresentada.