Untersuchungen zur Löslichkeit von Kobalt und Eisen in TiO 2-Bulk sowie in TiO 2-Nanoproben und deren Einfluss auf die magnetischen Eigenschaften

Co- und Fe-dotierte Rutil- und Anatas-Bulkproben wurden über einen Sol-Gel Prozess und anschließende thermische Behandlung dargestellt und auf ihre Zugehörigkeit zu der Gruppe der verdünnten magnetischen Oxide untersucht. Die Untersuchungen der dotierten Rutil-Proben mittels Röntgenbeugung, Elektronenmikroskopie und magnetischen Methoden zeigen, dass die Löslichkeit von Co und Fe in der TiO2-Modifikation Rutil sehr gering ist. Oberhalb von 1at% Co bzw. Fe wird neben Rutil die Bildung der Oxide CoTiO3 bzw. Fe2TiO5 beobachtet. Weitere thermische Behandlung im Argon-H2-Strom führte aufgrund der Bildung von metallischem Co bzw. Fe zu einem ferromagnetischen Verhalten. Die TiO2-Modifikation Anatas besitzt eine höhere Löslichkeit, so dass erst oberhalb von 4at% Co bzw. 10at% Fe die Phasen Co3O4 bzw. FeTiO3 neben Anatas auftreten. Entsprechende Proben zeigen ein paramagnetisches Verhalten. Oberhalb der Löslichkeitsgrenze führt die Reduktion im Argon-H2-Strom zu einem ferromagnetischen Verhalten, welches auf metallisches Co bzw. Fe zurückzuführen ist. Analog zu den Bulkproben wurden Co- und Fe-dotierte TiO2-Nanodrähte hergestellt. Das magnetische Verhalten der Fe-dotierten TiO2-Nanodrähte entspricht dem der Fe-dotierten Anatas-Bulkproben. Dagegen führt die Co-Dotierung nicht zu einem Einbau in die TiO2-Nanodrähte, sondern zur Bildung von CoOx-Nanopartikeln. Die entsprechenden Proben zeigen ein schwach ferromagnetisches Verhalten. Dies ist jedoch nicht auf eine ferromagnetische Dotierung der TiO2-Nanodrähte zurückzuführen, sondern auf nicht kompensierte Momente an den Oberflächen der als Verunreinigungen auftretenden CoOx-Nanopartikel. Zusammenfassend wird festgestellt, dass die Löslichkeit von Co und Fe in TiO2 für die Ausbildung eines ferromagnetischen Verhaltens zu gering ist. Der beobachtete Ferromagnetismus lässt sich eindeutig auf magnetische Verunreinigungen zurückführen. Somit können die dotierten TiO2 Proben nicht den verdünnten magnetischen Oxiden zugeordnet werden.

Weathering of Fe-bearing minerals under extraterrestrial conditions, investigated by Mössbauer spectroscopy

The weathering of Fe-bearing minerals under extraterrestrial conditions was investigated by Mössbauer (MB) spectroscopy to gain insights into the role of water on the planet Mars. The NASA Mars Exploration Rovers Spirit and Opportunity each carry a miniaturized Mössbauer spectrometer MIMOS II for the in situ investigation of Martian soils and rocks as part of their payload. The MER flight instruments had to be modified in order to work over the Martian diurnal temperature range (180 K – 290 K) and within the unique electronic environment of the rovers. The modification required special calibration procedures. The integration time necessary to obtain a good quality Mössbauer spectrum with the MIMOS II flight instruments was reduced by 30 % through the design of a new collimator. The in situ investigation of rocks along the rover Spirit's traverse in Gusev crater revealed weakly altered olivine basalt on the plains and pervasively altered basalt in the Columbia Hills. Correlation plots of primary Fe-bearing minerals identified by MB spectroscopy such as olivine versus secondary Fe-bearing phases such as nanophase Fe oxides showed that olivine is the mineral which is primarily involved in weathering reactions. This argues for a reduced availability of water. Identification of the Fe-oxyhydroxide goethite in the Columbia Hills is unequivocal evidence for aqueous weathering processes in the Columbia Hills. Experiments in which mineral powders were exposed to components of the Martian atmosphere showed that interaction with the atmosphere alone, in the absence of liquid water, is sufficient to oxidize Martian surface materials. The fine-grained dust suspended in the Martian atmosphere may have been altered solely by gas-solid reactions. Fresh and altered specimens of Martian meteorites were investigated with MIMOS II. The study of Martian meteorites in the lab helped to identify in Bounce Rock the first rock on Mars which is similar in composition to basaltic shergottites, a subgroup of the Martian meteorites. The field of astrobiology includes the study of the origin, evolution and distribution of life in the universe. Water is a prerequisite for life. The MER Mössbauer spectrometers identified aqueous minerals such as jarosite and goethite. The identification of jarosite was crucial to evaluate the habitability of Opportunity's landing site at Meridiani Planum during the formation of the sedimentary outcrop rocks, because jarosite puts strong constrains on pH levels. The identification of olivine in rocks and soils on the Gusev crater plains provide evidence for the sparsity of water under current conditions on Mars. Ratios of Fe2+/Fe3+ were obtained with Mössbauer spectroscopy from basaltic glass samples which were exposed at a deep sea hydrothermal vent. The ratios were used as a measure of potential energy for use by a microbial community. Samples from Mars analogue field sites on Earth exhibiting morphological biosignatures were also investigated.

Physiological and Biochemical Aspects of Iron Nutrition in Grapevine

The objective of this thesis was to study the response mechanisms of grapevine to Fe-deficiency and to potential Fe chlorosis prevention strategies. The results show that the presence of bicarbonate in the nutrient solution shifted the activity of PEPC and TCA cycle enzymes and the accumulation/translocation of organic acids in roots of Fe-deprived plants. The rootstock 140 Ruggeri displayed a typical behavior of calcicole plants under bicarbonate stress. The Fe chlorosis susceptible rootstock 101-14 reacted to a prolonged Fe-deficiency reducing the root activity of PEPC and MDH. Noteworthy, it accumulates high levels of citric acid in roots, indicating a low capacity to utilizing, transporting and/or exudating organic acids into the rhizosfere. In contrast, 110 Richter rootstock is capable to maintain an active metabolism of organic acids in roots, accumulating them to a lesser extent than 101-14. Similarly to 101-14, SO4 genotype displays a strong decrease of mechanisms associated to Fe chlorosis tolerance (PEPC and MDH enzymes). Nevertheless it is able to avoid excessive accumulation of citric acid in roots, similar as 110 Richter rootstock. Intercropping with Festuca rubra increased leaf chlorophyll content and net photosynthesis. In addition, intercropping reduces the activity of PEPC in roots, similary to Fe-chelate supply. Applications of NH4+ with nitrification inhibitor prevents efficiently Fe-deficiency, increases chlorophyll content, and induces similar root biochemical responses as Fe-EDDHA. Without the addition of nitrification inhibitors, the effectiveness of NH4+ supply on Fe chlorosis prevention resulted significantly lower. The aspects intertwined in this investigation highlight the complexity of Fe physiology and the fine metabolic tuning of grapevine genotypes to Fe availability and soil-related environmental factors. The experimental evidences reveal the need to carry out future researches on Fe nutrition maintaining a continous flow of knowledge between theoretical and agronomical perspectives for fully supporting the efforts devoted to convert science into practice.

Computational studies on the structure and stabilities of magnetic inter-metallic compounds

The purpose of this thesis is to further the understanding of the structural, electronic and magnetic properties of ternary inter-metallic compounds using density functional theory (DFT). Four main problems are addressed. First, a detailed analysis on the ternary Heusler compounds is made. It has long been known that many Heusler compounds ($X_2YZ$; $X$ and $Y$ transition elements, $Z$ main group element) exhibit interesting half-metallic and ferromagnetic properties. In order to understand these, the dependence of magnetic and electronic properties on the structural parameters, the type of exchange-correlation functional and electron-electron correlation was examined. It was found that almost all Co$_2YZ$ Heusler compounds exhibit half-metallic ferromagnetism. It is also observed that $X$ and $Y$ atoms mainly contribute to the total magnetic moment. The magnitude of the total magnetic moment is determined only indirectly by the nature of $Z$ atoms, and shows a trend consistent with Slater-Pauling behaviour in several classes of these compounds. In contrast to experiments, calculations give a non-integer value of the magnetic moment in certain Co$_2$-based Heusler compounds. To explain deviations of the calculated magnetic moment, the LDA+$U$ scheme was applied and it was found that the inclusion of electron-electron correlation beyond the LSDA and GGA is necessary to obtain theoretical description of some Heusler compounds that are half-metallic ferromagnets. The electronic structure and magnetic properties of substitutional series of the quaternary Heusler compound Co$_2$Mn$_{1-x}$Fe$_x$Si were investigated under LDA+$U$. The calculated band structure suggest that the most stable compound in a half-metallic state will occur at an intermediate Fe concentration. These calculated findings are qualitatively confirmed by experimental studies. Second, the effect of antisite disordering in the Co$_2$TiSn system was investigated theoretically as well as experimentally. Preservation of half-metallicity for Co$_2$TiSn was observed with moderate antisite disordering and experimental findings suggest that the Co and Ti antisites disorder amounts to approximately 10~% in the compound. Third, a systematic examination was carried out for band gaps and the nature (covalent or ionic) of bonding in semiconducting 8- and 18-electron or half-metallic ferromagnet half-Heusler compounds. It was found that the most appropriate description of these compounds from the viewpoint of electronic structures is one of a $YZ$ zinc blende lattice stuffed by the $X$ ion. Simple valence rules are obeyed for bonding in the 8- and 18-electron compounds. Fourth, hexagonal analogues of half-Heusler compounds have been searched. Three series of compounds were investigated: GdPdSb, GdAutextit{X} (textit{X} = Mn, Cd and In) and EuNiP. GdPdSb is suggested as a possible half-metallic weak ferromagnet at low temperature. GdAutextit{X} (textit{X} = Mn, Cd and In) and EuNiP were investigated because they exhibit interesting bonding, structural and magnetic properties. The results qualitatively confirm experimental studies on magnetic and structural behaviour in GdPdSb, GdAutextit{X} (textit{X} = Mn, Cd and In) and EuNiP compounds. ~

Experimental analysis and FE Modeling of Aluminium alloys Microstructural Evolution in Extrusion

Extrusion is a process used to form long products of constant cross section, from simple billets, with a high variety of shapes. Aluminum alloys are the materials most processed in the extrusion industry due to their deformability and the wide field of applications that range from buildings to aerospace and from design to automotive industries. The diverse applications imply different requirements that can be fulfilled by the wide range of alloys and treatments, that is from critical structural application to high quality surface and aesthetical aspect. Whether one or the other is the critical aspect, they both depend directly from microstructure. The extrusion process is moreover marked by high deformations and complex strain gradients making difficult the control of microstructure evolution that is at present not yet fully achieved. Nevertheless the evolution of Finite Element modeling has reached a maturity and can therefore start to be used as a tool for investigation and prediction of microstructure evolution. This thesis will analyze and model the evolution of microstructure throughout the entire extrusion process for 6XXX series aluminum alloys. Core phase of the work was the development of specific tests to investigate the microstructure evolution and validate the model implemented in a commercial FE code. Along with it two essential activities were carried out for a correct calibration of the model beyond the simple research of contour parameters, thus leading to the understanding and control of both code and process. In this direction activities were also conducted on building critical knowhow on the interpretation of microstructure and extrusion phenomena. It is believed, in fact, that the sole analysis of the microstructure evolution regardless of its relevance in the technological aspects of the process would be of little use for the industry as well as ineffective for the interpretation of the results.

"Sleeping Princess" (1921) e "Baiser de la Fée" (1928): lesina e punteruolo di Stravinskij sulle musiche di Čajkovskij.

Igor Stravinskij (1882-1971) utilizzò di sovente fonti preesistenti come parte integrante del proprio artigianato compositivo. In questa tesi dottorale ho studiato il processo creativo di Stravinskij negli anni Venti sulle musiche di Pëtr Il'ič Čajkovskij (1840-1893). Nella prima parte della dissertazione ho indagato la Sleeping Princess (1921) e il successivo Mariage d’Aurore (1922-1929), entrambi allestiti dai Ballets russes di Sergej Djagilev (1872-1929). Dopo aver localizzato e contestualizzato le fonti manoscritte e i materiali d’uso, ho ricostruito le ri-orchestrazioni effettuate da Stravinskij della Danse russe (Coda del Pas de deux n. 28) e del Presto del Finale (n. 30), che erano a tutt’oggi inedite. La ricerca sulla Sleeping Princess si è rivelata fondamentale per la conseguente analisi del Baiser de la Fée (1928, Ballets de Mme Ida Rubinstein), balletto basato su pezzi pianistici e romanze per voce e pianoforte di Čajkovskij. Grazie allo studio dello Skizzenbuch VIII, della partitura pianistica manoscritta e di tutte le fonti rinvenute, ho gettato ulteriore luce sul processo compositivo di Stravinskij sulle fonti čajkovskiane. Ho rinvenuto nuove appropriazioni che finora non erano note.

Investigation on laser shock peening capability by FE simulation

Laser shock peening is a technique similar to shot peening that imparts compressive residual stresses in materials for improving fatigue resistance. The ability to use a high energy laser pulse to generate shock waves, inducing a compressive residual stress field in metallic materials, has applications in multiple fields such as turbo-machinery, airframe structures, and medical appliances. The transient nature of the LSP phenomenon and the high rate of the laser's dynamic make real time in-situ measurement of laser/material interaction very challenging. For this reason and for the high cost of the experimental tests, reliable analytical methods for predicting detailed effects of LSP are needed to understand the potential of the process. Aim of this work has been the prediction of residual stress field after Laser Peening process by means of Finite Element Modeling. The work has been carried out in the Stress Methods department of Airbus Operations GmbH (Hamburg) and it includes investigation on compressive residual stresses induced by Laser Shock Peening, study on mesh sensitivity, optimization and tuning of the model by using physical and numerical parameters, validation of the model by comparing it with experimental results. The model has been realized with Abaqus/Explicit commercial software starting from considerations done on previous works. FE analyses are “Mesh Sensitive”: by increasing the number of elements and by decreasing their size, the software is able to probe even the details of the real phenomenon. However, these details, could be only an amplification of real phenomenon. For this reason it was necessary to optimize the mesh elements' size and number. A new model has been created with a more fine mesh in the trough thickness direction because it is the most involved in the process deformations. This increment of the global number of elements has been paid with an "in plane" size reduction of the elements far from the peened area in order to avoid too high computational costs. Efficiency and stability of the analyses has been improved by using bulk viscosity coefficients, a merely numerical parameter available in Abaqus/Explicit. A plastic rate sensitivity study has been also carried out and a new set of Johnson Cook's model coefficient has been chosen. These investigations led to a more controllable and reliable model, valid even for more complex geometries. Moreover the study about the material properties highlighted a gap of the model about the simulation of the surface conditions. Modeling of the ablative layer employed during the real process has been used to fill this gap. In the real process ablative layer is a super thin sheet of pure aluminum stuck on the masterpiece. In the simulation it has been simply reproduced as a 100µm layer made by a material with a yield point of 10MPa. All those new settings has been applied to a set of analyses made with different geometry models to verify the robustness of the model. The calibration of the model with the experimental results was based on stress and displacement measurements carried out on the surface and in depth as well. The good correlation between the simulation and experimental tests results proved this model to be reliable.

Messung von Q beta-Werten neutronenreicher Tc- bis Pd-Isotope im Massenbereich A=110 bis A=117

In der vorliegenden Arbeit wurden zwölf Q(beta)-Werte von beta-instabilen Pd, Ru, Rh und Tc-Isotopen gemessen. Der betrachtete Massenbereich A=110 bis A=117 liegt am Rande des bekannten Gebiets der Nuklidkarte und umfasst sehr neutronenreiche kurzlebige Isotope dieser Elemente, die sich durch geringe Spalthäufigkeit auszeichnen. Durch die geringen (Spalt-)Häufigkeiten dieser Nuklide liegen kaum Daten vor, teilweise auch nicht über die Niveauschemata. Es ist daher notwendig, eine protoneninduzierte Spaltungsreaktion zur Darstellung dieser Isotope zu verwenden und die Spaltprodukte innerhalb kürzester Zeit für die Messung nach Massen aufzutrennen, wie dies am IGISOL in Jyväskylä/Finnland geschieht. Die aufgebaute Apparatur zur beta,gamma,X-Koinzidenz erlaubt es, während ein und desselben Experiments neben der Messung der Q(beta)-Werte gleichzeitig gamma,X-Koinzidenzen auszuwerten, die die benötigten Grundinformationen für die Q(beta)-Bestimmung über die beta,gamma-Koinzidenzen liefern. Es können somit nicht nur Q(beta)-Werte von Nukliden mit bereits bekannten Niveauschemata ermittelt, sondern auch erfolgreich Nuklide mit unvollständigen Niveauschemata einer ersten Messung unterzogen werden. Umgekehrt können beta,gamma-Koinzidenzdaten weitere Informationen zum Aufbau neuer Niveauschemata liefern. Mit Hilfe der beschriebenen Koinzidenzmessung konnten zwölf Q(beta)-Werte von sehr neutronenreichen Pd- bis Tc-Isotopen gemessen und daraus die Kernmassen, Massenüberschüsse und Neutronen-Separationsenergien bestimmt werden. Von diesen wurden acht Werte erstmalig bestimmt, ein weiterer Wert konnte bestätigt sowie die Fehler von drei weiteren Werten um den Faktor Zehn verringert werden. Die gewonnenen Daten sind von Interesse für die Beurteilung von Kernmassenmodellen und gehen ebenso in Modellrechnungen der nuklearen Astrophysik ein.

Genderperspektive und Frauenförderung in der deutschen Entwicklungszusammenarbeit : der „Entwicklungspolitische Gender-Aktionsplan 2009 - 2012“ des Bundesministeriums für wirtschaftliche Zusammenarbeit und Entwicklung (BMZ)/// Arbeitspapiere / Institut für Ethnologie und Afrikastudien ; 110

Der vorliegende Artikel befasst sich mit aktuellen Strategien bezüglich Gender und Frauenförderung in der deutschen Entwicklungspolitik. Dabei steht eine Analyse des „Entwicklungspolitischen Gender-Aktionsplans 2009-2012“ des Bundesministeriums für Wirtschaftliche Zusammenarbeit und Entwicklung (BMZ) im Fokus. Ausgangspunkt hierfür ist die internationale Debatte über Gender und Frauenförderung in der Entwicklungspolitik, welche eine Reihe unterschiedlicher, zum Teil konträrer Argumentationsstränge und strategischer Handlungsweisen hervorgebracht hat. Auf den ersten Blick ist das BMZ den neuesten Entwicklungen in dieser Debatte vollständig gefolgt. Die Analyse des Gender-Aktionsplans zeigt jedoch, dass in der Politikformulierung des BMZ nur partiell auf Argumente zurückgegriffen wird, die eine konsequente Einbeziehung von Gender sowie die Umsetzung von Empowerment und Gender Mainstreaming fordern. Das Resultat ist eine unzulängliche Darstellung von Frauen und Geschlechterverhältnissen in Entwicklungsländern.

Serumfreie Collagen-Monolayer- und Sandwich-Kulturen primärer Hepatozyten als ein wertvolles Modell zur Detektion von Toxizität und Arzneimittelwechselwirkungen in vitro

In dieser Arbeit wurden Zellkulturen primärer Hepatozyten von Ratte und Mensch hinsichtlich ihrer Eignung untersucht Speziesunterschiede der toxischen Wirkung und des Metabolismus von Substanzen darzustellen und inwieweit die in vitro-Ergebnisse in vivo vergleichbar bzw. übertragbar sind. Des Weiteren wurde ein Zellkulturmodell entwickelt, das eine Kultivierung von primären Hepatozyten aus Ratte, Mensch und Maus über einen Zeitraum von mindestens einer bis zwei Wochen erlaubt.rnrnDie Zellkulturen primärer Hepatozyten von Ratte und Mensch zeigten deutliche Unterschiede in der substanzinduzierten Veränderung der Genexpression nach Behandlung mit den, vor allem für den Menschen, lebertoxischen Substanzen Diclofenac und Troglitazon. Diese Unterschiede traten hauptsächlich in der Induktion fremdstoffmetabolisierender Enzyme sowie deren transkriptionsregulierenden Kernrezeptoren in den humanen Hepatozyten auf. Ebenso war eine verstärkte Stressantwort zu beobachten.rnDeutliche Speziesunterschiede konnten ebenso in der Wirkung der Arzneimittelentwicklungssubstanz EMD 392949 auf die Aktivität bzw. Genexpression von Cytochrom P450 Enzymen sowie deren Regulatoren nachgewiesen werden. Des Weiteren konnte hier eine sehr gute Übereinstimmung der Ergebnisse aus den Zellkulturen primärer Ratten- bzw. Humanhepatozyten mit jenen aus in vivo-Experimenten mit Ratten bzw. Affen (Macaca fascicularis) beobachtet werden, was die Aussagekraft der Primärkulturen verdeutlichte.rnDie große Übereinstimmung zwischen Enzymaktivität und Genexpression in der Induktion fremdstoffmetabolisierender Enzyme konnte durch die Behandlung mit einer Reihe speziesspezifischer Induktoren in Zellkulturen primärer Ratten- bzw. Humanhepatozyten bestätigt werden; vor allem nach dem von der amerikanischen Arzneimittelzulassungsbehörde (FDA, Food and Drug Administartion) vorgeschlagenen Bewertungsschema zur Untersuchung der CYP-Induktion.rnrnDie Lebensdauer sowie der Differenzierungsgrad von primären Hepatozyten in Kultur sind stark abhängig von den Zellkulturbedingungen. Durch diese Arbeit konnte gezeigt werden, dass spezifische Eigenschaften von Rattenleberzellen durch Kultivierung in einem Sandwich aus zwei hydratisierten Collagengelschichten und unter serumfreien Bedingungen für einen Zeitraum von mindestens zwei Wochen aufrechterhalten werden können. Dieses Kulturmodel konnte auf Primärhepatozyten von Mensch und Maus übertragen werden und erweitert die möglichen Anwendungen hin zu einer Behandlung über einen längeren Zeitraum und der Untersuchung von subchronischen Effekten.rn

Hard x-ray photoelectron spectroscopy of bulk and thin films of Heusler compounds

X-ray photoemission spectroscopy (XPS) is one of the most universal and powerful tools for investigation of chemical states and electronic structures of materials. The application of hard x-rays increases the inelastic mean free path of the emitted electrons within the solid and thus makes hard x-ray photoelectron spectroscopy (HAXPES) a bulk sensitive probe for solid state research and especially a very effective nondestructive technique to study buried layers.rnThis thesis focuses on the investigation of multilayer structures, used in magnetic tunnel junctions (MTJs), by a number of techniques applying HAXPES. MTJs are the most important components of novel nanoscale devices employed in spintronics. rnThe investigation and deep understanding of the mechanisms responsible for the high performance of such devices and properties of employed magnetic materials that are, in turn, defined by their electronic structure becomes feasible applying HAXPES. Thus the process of B diffusion in CoFeB-based MTJs was investigated with respect to the annealing temperature and its influence on the changes in the electronic structure of CoFeB electrodes that clarify the behaviour and huge TMR ratio values obtained in such devices. These results are presented in chapter 6. The results of investigation of the changes in the valence states of buried off-stoichiometric Co2MnSi electrodes were investigated with respect to the Mn content α and its influence on the observed TMR ratio are described in chapter 7.rnrnMagnetoelectronic properties such as exchange splitting in ferromagnetic materials as well as the macroscopic magnetic ordering can be studied by magnetic circular dichroism in photoemission (MCDAD). It is characterized by the appearance of an asymmetry in the photoemission spectra taken either from the magnetized sample with the reversal of the photon helicity or by reversal of magnetization direction of the sample when the photon helicity direction is fixed. Though recently it has been widely applied for the characterization of surfaces using low energy photons, the bulk properties have stayed inaccessible. Therefore in this work this method was integrated to HAXPES to provide an access to exploration of magnetic phenomena in the buried layers of the complex multilayer structures. Chapter 8 contains the results of the MCDAD measurements employing hard x-rays for exploration of magnetic properties of the common CoFe-based band-ferromagnets as well as half-metallic ferromagnet Co2FeAl-based MTJs.rnrnInasmuch as the magnetoresistive characteristics in spintronic devices are fully defined by the electron spins of ferromagnetic materials their direct measurements always attracted much attention but up to date have been limited by the surface sensitivity of the developed techniques. Chapter 9 presents the results on the successfully performed spin-resolved HAXPES experiment using a spin polarimeter of the SPLEED-type on a buried Co2FeAl0.5Si0.5 magnetic layer. The measurements prove that a spin polarization of about 50 % is retained during the transmission of the photoelectrons emitted from the Fe 2p3/2 state through a 3-nm-thick oxide capping layer.rn

Interazione di cluster carbonilici FE-CU con complessi di metalli di transizione e leganti azotati

Nel corso di questa Tesi sono state studiate reazioni di cluster carburo-carbonilici Fe/Cu con composti azotati di varia natura: complessi fosforescenti di metalli di transizione, 1-10 fenantrolina, L-amminoacidi e Chinolina. In particolare la reazione tra Fe4C(CO)12Cu2(CH3CN)2 e [Ru(tpy)(bpy)(N4C-C6H4-CN)]+ ha portato alla sintesi dell’addotto Fe4C(CO)12{Cu2Cl[Ru(tpy)(bpy)(N4C-C6H4-CN)]}, sul quale sono state condotte misure di luminescenza (emissione, eccitazione e misura dei tempi di vita degli stati eccitati). Per confronto degli spettri registrati su campioni di adotto in soluzione con quelli del complesso cationico di Ru(II), si è ipotizzato che l’addotto sintetizzato in soluzione dia origine ad un sistema in equilibrio tra le specie legate e dissociate. Le reazioni di Fe4C(CO)12Cu2(CH3CN)2 e [NEt4][Fe5C(CO)14Cu(CH3CN)] con 1-10 fenantrolina hanno permesso di isolare le nuove specie [Fe4C(CO)12(Cuphen)]–, [Fe4C(CO)12(Cuphen)] e [Fe5C(CO)14(Cuphen)]–, sottoforma dei loro sali [Cu(phen)2][Fe4C(CO)12(Cuphen)], [NEt4] [Fe4C(CO)12(Cuphen)], [Fe4C(CO)12(Cuphen)], [NEt4][Fe5C(CO)14(Cuphen)]• CH2Cl2 e [NEt4][Fe5C(CO)14(Cuphen)]•THF. In tali cluster si nota come la natura bidentata di phen e il suo ingombro sterico abbiano causato notevoli riarrangiamenti strutturali rispetto alle specie iniziali contenenti acetonitrile. La sintesi di Fe4C(CO)12(CuQ)2 e [NEt4][Fe5C(CO)14(CuQ)] è avvenuta inaspettatamente a partire dalle reazioni condotte tra Fe4C(CO)12Cu2(CH3CN)2 e [NEt4][Fe5C(CO)14Cu(CH3CN)] con le molecole L-prolina, L-metionina e guanina, a causa della chinolina contenuta come impurezza nei reagenti di partenza. L’esito di questa reazione ha comunque mostrato l’elevata affinità dei cluster per il legante chinolina, sebbene presente in ambiente di reazione in misura sensibilmente inferiore rispetto agli altri reagenti. Tutte le nuove specie sintetizzate sono stati caratterizzate mediante spettroscopia IR e le strutture molecolari sono state determinate mediante diffrazione di raggi X su cristallo singolo.

The role of dendritic cells (DC) in Friend retrovirus-induced immunosuppression and immunotherapeutic applications of functionalized nanoparticles

Friend murine leukemia Virus (FV) infection of immunocompetent mice is a well- established model to acquire further knowledge about viral immune suppression mechanisms, with the aim to develop therapeutics against retrovirus-induced diseases. Interestingly, BALB/c mice are infected by low doses of FV and die from FV-induced erythroleukemia, while C57/BL6 mice are infected by FV only at high viral dose, and remain persistently infected for their whole life. Due to the central role of dendritic cells (DC) in the induction of anti-viral responses, we asked for their functional role in the genotype-dependent sensitivity towards FV infection. In my PhD study I showed that bone marrow (BM)-derived DC differentiated from FV-infected BM cells obtained from FV-inoculated BALB/c (FV susceptible) and C57BL/6 (FV resistant) mice showed an increased endocytotic activity and lowered expression of MHCII and of costimulatory receptors as compared with non-infected control BMDC. FV-infected BMDC from either mouse strain were partially resistant towards stimulation-induced upregulation of MHCII and costimulators, and accordingly were poor T cell stimulators in vitro and in vivo. In addition, FV-infected BMDC displayed an altered expression profile of proinflammator cytokines and favoured Th2 polarization. Ongoing work is focussed on elucidating the functional role of proteins identified as differentially expressed in FV-infected DC in a genotype-dependent manner, which therefore may contribute to the differential course of FV infection in vivo in BALB/c versus C57BL/6 mice. So far, more than 300 proteins have been identified which are differently regulated in FV-infected vs. uninfected DC from both mouse strains. One of these proteins, S100A9, was strongly upregulated specifically in BMDC derived from FV-infected C57BL/6 BM cells. S100A9-/- mice were more sensitive towards inoculation with FV than corresponding wild type (WT) mice (both C57BL/6 background), which suggests a decisive role of this factor for anti-viral defense. In addition, FV-infected S100A9-/- BMDC showed lower motility than WT DC. The future work is aimed to further elucidate the functional importance of S100A9 for DC functions. To exploit the potential of DC for immunotherapeutic applications, in another project of this PhD study the usability of different types of functionalized nanoparticles

Dynamics of the Heisenberg XXZ model across the ferromagnetic transition

In questa tesi viene presentata un'analisi numerica dell'evoluzione dinamica del modello di Heisenberg XXZ, la cui simulazione è stata effettuata utilizzando l'algoritmo che va sotto il nome di DMRG. La transizione di fase presa in esame è quella dalla fase paramagnetica alla ferromagnetica: essa viene simulata in una catena di 12 siti per vari tempi di quench. In questo modo si sono potuti esplorare diversi regimi di transizione, da quello istantaneo al quasi-adiabatico. Come osservabili sono stati scelti l'entropia di entanglement, la magnetizzazione di mezza catena e lo spettro dell'entanglement, particolarmente adatti per caratterizzare la fisica non all'equilibrio di questo tipo di sistemi. Lo scopo dell'analisi è tentare una descrizione della dinamica fuori dall'equilibrio del modello per mezzo del meccanismo di Kibble-Zurek, che mette in relazione la sviluppo di una fase ordinata nel sistema che effettua la transizione quantistica alla densità di difetti topologici, la cui legge di scala è predicibile e legata agli esponenti critici universali caratterizzanti la transizione.