Low-Cost Micromechanically Tunable Optical Devices: Strained Resonator Engineering, Technological Implementation and Characterization

The rapid growth of the optical communication branches and the enormous demand for more bandwidth require novel networks such as dense wavelength division multiplexing (DWDM). These networks enable higher bitrate transmission using the existing optical fibers. Micromechanically tunable optical microcavity devices like VCSELs, Fabry-Pérot filters and photodetectors are core components of these novel DWDM systems. Several air-gap based tunable devices were successfully implemented in the last years. Even though these concepts are very promising, two main disadvantages are still remaining. On the one hand, the high fabrication and integration cost and on the other hand the undesired adverse buckling of the suspended membranes. This thesis addresses these two problems and consists of two main parts: • PECVD dielectric material investigation and stress control resulting in membranes shape engineering. • Implementation and characterization of novel tunable optical devices with tailored shapes of the suspended membranes. For this purposes, low-cost PECVD technology is investigated and developed in detail. The macro- and microstress of silicon nitride and silicon dioxide are controlled over a wide range. Furthermore, the effect of stress on the optical and mechanical properties of the suspended membranes and on the microcavities is evaluated. Various membrane shapes (concave, convex and planar) with several radii of curvature are fabricated. Using this resonator shape engineering, microcavity devices such as non tunable and tunable Fabry-Pérot filters, VCSELs and PIN photodetectors are succesfully implemented. The fabricated Fabry-Pérot filters cover a spectral range of over 200nm and show resonance linewidths down to 1.5nm. By varying the stress distribution across the vertical direction within a DBR, the shape and the radius of curvature of the top membrane are explicitely tailored. By adjusting the incoming light beam waist to the curvature, the fundamental resonant mode is supported and the higher order ones are suppressed. For instance, a tunable VCSEL with 26 nm tuning range, 400µW maximal output power, 47nm free spectral range and over 57dB side mode suppresion ratio (SMSR) is demonstrated. Other technologies, such as introducing light emitting organic materials in microcavities are also investigated.

Development of hybrid UV VCSEL with organic active material and dielectric DBR mirrors for medical, sensoric and data storage applications

Lasers play an important role for medical, sensoric and data storage devices. This thesis is focused on design, technology development, fabrication and characterization of hybrid ultraviolet Vertical-Cavity Surface-Emitting Lasers (UV VCSEL) with organic laser-active material and inorganic distributed Bragg reflectors (DBR). Multilayer structures with different layer thicknesses, refractive indices and absorption coefficients of the inorganic materials were studied using theoretical model calculations. During the simulations the structure parameters such as materials and thicknesses have been varied. This procedure was repeated several times during the design optimization process including also the feedback from technology and characterization. Two types of VCSEL devices were investigated. The first is an index coupled structure consisting of bottom and top DBR dielectric mirrors. In the space in between them is the cavity, which includes active region and defines the spectral gain profile. In this configuration the maximum electrical field is concentrated in the cavity and can destroy the chemical structure of the active material. The second type of laser is a so called complex coupled VCSEL. In this structure the active material is placed not only in the cavity but also in parts of the DBR structure. The simulations show that such a distribution of the active material reduces the required pumping power for reaching lasing threshold. High efficiency is achieved by substituting the dielectric material with high refractive index for the periods closer to the cavity. The inorganic materials for the DBR mirrors have been deposited by Plasma- Enhanced Chemical Vapor Deposition (PECVD) and Dual Ion Beam Sputtering (DIBS) machines. Extended optimizations of the technological processes have been performed. All the processes are carried out in a clean room Class 1 and Class 10000. The optical properties and the thicknesses of the layers are measured in-situ by spectroscopic ellipsometry and spectroscopic reflectometry. The surface roughness is analyzed by atomic force microscopy (AFM) and images of the devices are taken with scanning electron microscope (SEM). The silicon dioxide (SiO2) and silicon nitride (Si3N4) layers deposited by the PECVD machine show defects of the material structure and have higher absorption in the ultra violet range compared to ion beam deposition (IBD). This results in low reflectivity of the DBR mirrors and also reduces the optical properties of the VCSEL devices. However PECVD has the advantage that the stress in the layers can be tuned and compensated, in contrast to IBD at the moment. A sputtering machine Ionsys 1000 produced by Roth&Rau company, is used for the deposition of silicon dioxide (SiO2), silicon nitride (Si3N4), aluminum oxide (Al2O3) and zirconium dioxide (ZrO2). The chamber is equipped with main (sputter) and assisted ion sources. The dielectric materials were optimized by introducing additional oxygen and nitrogen into the chamber. DBR mirrors with different material combinations were deposited. The measured optical properties of the fabricated multilayer structures show an excellent agreement with the results of theoretical model calculations. The layers deposited by puttering show high compressive stress. As an active region a novel organic material with spiro-linked molecules is used. Two different materials have been evaporated by utilizing a dye evaporation machine in the clean room of the department Makromolekulare Chemie und Molekulare Materialien (mmCmm). The Spiro-Octopus-1 organic material has a maximum emission at the wavelength λemission = 395 nm and the Spiro-Pphenal has a maximum emission at the wavelength λemission = 418 nm. Both of them have high refractive index and can be combined with low refractive index materials like silicon dioxide (SiO2). The sputtering method shows excellent optical quality of the deposited materials and high reflection of the multilayer structures. The bottom DBR mirrors for all VCSEL devices were deposited by the DIBS machine, whereas the top DBR mirror deposited either by PECVD or by combination of PECVD and DIBS. The fabricated VCSEL structures were optically pumped by nitrogen laser at wavelength λpumping = 337 nm. The emission was measured by spectrometer. A radiation of the VCSEL structure at wavelength 392 nm and 420 nm is observed.

Nutrient cycling and nutrient use efficiency in urban and peri-urban agriculture of Kabul, Afghanistan

Like elsewhere also in Kabul, Afghanistan urban and peri-urban agriculture (UPA) has often been accused of being resource inefficient and unsustainable causing negatives externalities to community health and to the surroundings. These arise from the inappropriate management and use of agricultural inputs, including often pesticides and inter-city wastes containing heavy metal residues and pathogens. To address these concerns, parallel studies with the aims of quantification of carbon (C), nitrogen (N), phosphorus (P) and potassium (K) horizontal and vertical fluxes; the assessment of heavy metal and pathogen contaminations of UPA produce, and an economic analysis of cereal, vegetable and grape production systems conducted for two years in UPA of Kabul from April 2008 to October 2009. The results of the studies from these three UPA diverse production systems can be abridged as follows: Biennial net balances in vegetable production systems were positive for N (80 kg ha-1 ), P (75 kg ha-1) and C (3,927 kg ha-1), negative for K (-205 kg ha-1), whereas in cereal production systems biennial horizontal balances were positive for P (20 kg ha-1 ) and C (4,900 kg ha-1) negative for N (-155 kg ha-1) and K (-355 kg ha-1) and in vineyards corresponding values were highly positive for N (295 kg ha-1), P (235 kg ha-1), C (3,362 kg ha-1) and slightly positive for K (5 kg ha-1). Regardless of N and C gaseous emissions, yearly leaching losses of N and P in selected vegetable gardens varied from 70 - 205 kg N ha-1 and 5 - 10 kg P ha-1. Manure and irrigation water contributed on average 12 - 79% to total Inputs of N, P, K and C, 10 - 53% to total inputs of C in the gardens and fields. The elevated levels of heavy metal and pathogen loads on fresh UPA vegetables reflected contamination from increasing traffic in the city, deposits of the past decades of war, lacking collection and treatment of raw inter-city wastes which call for solutions to protect consumer and producer health and increase reliability of UPA productions. A cost-revenue analysis of all inputs and outputs of cereal, vegetable and grapes production systems over two years showed substantial differences in net UPA household income. To confirm these results, more detailed studies are needed, but tailoring and managing the optimal application of inputs to crop needs will significantly enhance farmer’s better revenues as will as environmental and produce quality.

Development of directly modulated high speed telecommunication lasers based on surface defined feedback gratings

High-speed semiconductor lasers are an integral part in the implemen- tation of high-bit-rate optical communications systems. They are com- pact, rugged, reliable, long-lived, and relatively inexpensive sources of coherent light. Due to the very low attenuation window that exists in the silica based optical fiber at 1.55 μm and the zero dispersion point at 1.3 μm, they have become the mainstay of optical fiber com- munication systems. For the fabrication of lasers with gratings such as, distributed bragg reflector or distributed feedback lasers, etching is the most critical step. Etching defines the lateral dimmensions of the structure which determines the performance of optoelectronic devices. In this thesis studies and experiments were carried out about the exist- ing etching processes for InP and a novel dry etching process was de- veloped. The newly developed process was based on Cl2/CH4/H2/Ar chemistry and resulted in very smooth surfaces and vertical side walls. With this process the grating definition was significantly improved as compared to other technological developments in the respective field. A surface defined grating definition approach is used in this thesis work which does not require any re-growth steps and makes the whole fabrication process simpler and cost effective. Moreover, this grating fabrication process is fully compatible with nano-imprint lithography and can be used for high throughput low-cost manufacturing. With usual etching techniques reported before it is not possible to etch very deep because of aspect ratio dependent etching phenomenon where with increasing etch depth the etch rate slows down resulting in non-vertical side walls and footing effects. Although with our de- veloped process quite vertical side walls were achieved but footing was still a problem. To overcome the challenges related to grating defini- tion and deep etching, a completely new three step gas chopping dry etching process was developed. This was the very first time that a time multiplexed etching process for an InP based material system was demonstrated. The developed gas chopping process showed extra ordinary results including high mask selectivity of 15, moderate etch- ing rate, very vertical side walls and a record high aspect ratio of 41. Both the developed etching processes are completely compatible with nano imprint lithography and can be used for low-cost high-throughput fabrication. A large number of broad area laser, ridge waveguide laser, distributed feedback laser, distributed bragg reflector laser and coupled cavity in- jection grating lasers were fabricated using the developed one step etch- ing process. Very extensive characterization was done to optimize all the important design and fabrication parameters. The devices devel- oped have shown excellent performance with a very high side mode suppression ratio of more than 52 dB, an output power of 17 mW per facet, high efficiency of 0.15 W/A, stable operation over temperature and injected currents and a threshold current as low as 30 mA for almost 1 mm long device. A record high modulation bandwidth of 15 GHz with electron-photon resonance and open eye diagrams for 10 Gbps data transmission were also shown.

Optimization in the Technological Steps for the Fabrication of Large Area Micromirror Arrays

Micromirror arrays are a very strong candidate for future energy saving applications. Within this work, the fabrication process for these micromirror arrays has been optimized and some steps for the large area fabrication of micromirror modules were performed. At first the surface roughness of the insulation layer of silicon dioxide (SiO2) was investigated. This SiO2 thin layer was deposited on three different type of substrates i.e. silicon, glass and Polyethylene Naphthalate (PEN) substrates. The deposition techniques which has been used are Plasma Enhanced Chemical Vapor Deposition (PECVD), Physical Vapor Deposition (PVD) and Ion Beam Sputter Deposition (IBSD). The thickness of the SiO2 thin layer was kept constant at 150nm for each deposition process. The surface roughness was measured by Stylus Profilometry and Atomic Force Microscopy (AFM). It was found that the layer which was deposited by IBSD has got the minimum surface roughness value and the layer which was deposited by PECVD process has the highest surface roughness value. During the same investigation, the substrate temperature of PECVD was varied from 80° C to 300° C with the step size of 40° C and it was found that the surface roughness keeps on increasing as the substrate holder temperature increases in the PECVD process. A new insulation layer system was proposed to minimize the dielectric breakdown effect in insulation layer for micromirror arrays. The conventional bilayer system was replaced by five layer system but the total thickness of insulation layer remains the same. It was found that during the actuation of micromirror arrays structure, the dielectric breakdown effect was reduced considerably as compared to the bilayer system. In the second step the fabrication process of the micromirror arrays was successfully adapted and transferred from glass substrates to the flexible PEN substrates by optimizing the conventional process recipe. In the last section, a large module of micromirror arrays was fabricated by electrically interconnecting four 10cm×10cm micromirror modules on a glass pane having dimensions of 21cm×21cm.

Technical and scale efficiency of cassava production system in Delta State, Nigeria: an application of Two-Stage DEA approach

The present study examines the level of pure technical and scale efficiencies of cassava production system including its sub-processes (that is production and processing stages) of 278 cassava farmers/processors from three regions of Delta State, Nigeria by applying Two-Stage Data Envelopment Analysis (DEA) approach. Results reveal that pure technical efficiency (PTE) is significantly lower at the production stage 0.41 vs 0.55 for the processing stage, but scale efficiency (SE) is high at both stages (0.84 and 0.87), implying that productivity can be improved substantially by reallocation of resources and adjusting operation size. The socio-economic determinants exert differential impacts on PTE and SE at each stage. Overall, education, experience and main occupation as farmer significantly improve SE while subsistence pressure reduces it. Extension contact significantly improves SE at the processing stage but reduces PTE and SE overall. Inverse size-PTE and size-SE relationships exist in cassava production system. In other words, large/medium farms are technically and scale inefficient. Gender gap exists in performance. Male farmers are technically efficient at processing stage but scale inefficient overall. Farmers in northern region are technically efficient. Investments in education, extension services and infrastructure are suggested as policy options to improve the cassava sector in Nigeria.

Determinants of technical efficiency of freshwater prawn farming in southwestern Bangladesh

This paper estimates a translog stochastic production function to examine the determinants of technical efficiency of freshwater prawn farming in Bangladesh. Primary data has been collected using random sampling from 90 farmers of three villages in southwestern Bangladesh. Prawn farming displayed much variability in technical efficiency ranging from 9.50 to 99.94% with mean technical efficiency of 65%, which suggested a substantial 35% of potential output can be recovered by removing inefficiency. For a land scarce country like Bangladesh this gain could help increase income and ensure better livelihood for the farmers. Based on the translog production function specification, farmers could be made scale efficient by providing more input to produce more output. The results suggest that farmers’ education and non-farm income significantly improve efficiency whilst farmers’ training, farm distance from the water canal and involvement in fish farm associations reduces efficiency. Hence, the study proposes strategies such as less involvement in farming-related associations and raising the effective training facilities of the farmers as beneficial adjustments for reducing inefficiency. Moreover, the key policy implication of the analysis is that investment in primary education would greatly improve technical efficiency.

Technological convergence: a strategic perspective

The information and communication technologies (ICT) sectors are in a process of technological convergence. Determinant factors in this process are the liberalisation of the telecommunications markets and technological change. Many firms are engaged in a process of mergers and alliances to position themselves in this new framework. Technological and demand uncertainties are very important. Our objective in this paper is to study the economic determinants of the strategies of the firms. With this aim, we review some key technological and demand aspects. We shed some light on the strategic motivations of the firms by establishing a parallel with the evolution of the retailing sector

The efficiency of direct payments versus tax reductions under uncertainty

This paper analyzes the optimal behavior of farmers in the presence of direct payments and uncertainty. In an empirical analysis for Switzerland, it confirms previously obtained theoretical results and determines the magnitude of the theoretical predicted effects. The results show that direct payments increase agricultural production between 3.7% to 4.8%. Alternatively to direct payments, the production effect of tax reductions is evaluated in order to determine its magnitude. The empirical analysis corroborates the theoretical results of the literature and demonstrates that tax reductions are also distorting, but to a substantially lesser degree if losses are not offset. However, tax reductions, independently whether losses are offset or not, lead to higher government spending than pure direct payments

Panorama de la contratación pública electrónica en Colombia

La implementación de los procesos de contratación pública electrónica permite aprovechar las ventajas de los avances tecnológicos en el manejo de la información y las telecomunicaciones, con el fin de aumentar la eficiencia y la eficacia de los procesos de contratación estatal, así como la transparencia de los mismos. En ese sentido, el presente trabajo de investigación se centrará en analizar si, de acuerdo con nuestro modelo jurídico, el procedimiento administrativo electrónico como “equivalente funcional” del procedimiento administrativo tradicional, posibilita la simplificación y racionalización de trámites en los procesos de contratación que adelanta la Administración Pública, permitiendo la realización de los principios de igualdad, moralidad, eficacia, economía, eficiencia, celeridad, imparcialidad y publicidad.

Biased Technological Change, Impatience and Welfare

En este artículo utilizamos un modelo de generaciones traslapadas con heterogeneidad en la tasa de impaciencia para mostrar que los efectos de un cambio tecnológico aumentador de capital no son simétricos en los agentes y pueden conllevar una reducci on en el consumo. La asimetría en la tasa de impaciencia de los agentes en un período, tiene consecuencias sobre los beneficios del cambio tecnológico para las generaciones futuras. Menores tasas de impaciencia llevan a mayores niveles de capital y de consumo, si se entiende que la economía tiene el suficiente nivel de capital per capita.

Análisis y diseño para la construcción de un plan estratégico de manejo eficiente de energía en la Universidad del Rosario

De acuerdo con el Programa de la Naciones Unidas para el Medio Ambiente (PNUMA), la producción más limpia «es una estrategia ambiental preventiva integrada que se aplica a los procesos, productos y servicios a fin de aumentar la eficiencia y reducir los riesgos para los seres humanos y el ambiente.» (Programa de las Naciones Unidas para el Medio Ambiente (PNUMA), 2006) Esta estrategia es aplicable para cualquier proceso, producto o servicio y contiene diversas acciones que incluyen sencillos pasos que van desde pequeños cambios en los procedimientos operacionales de fácil e inmediata ejecución, hasta cambios mayores que impliquen la sustitución de materias primas, insumos o líneas de producción a unas más eficientes. De acuerdo con la investigación realizada, se formuló un plan estratégico de PML para la Universidad del Rosario que permita la conservación de las materias primas, como el agua y el manejo energético eficiente, la reducción de las materias primas toxicas, en cuanto a toxicidad y cantidad, y la reducción de emisiones y residuos que van al agua y a la atmósfera impactando el entorno a causa de los procesos que se desarrollan en la Universidad para la prestación de sus servicios. En este orden de ideas, la Producción más Limpia implementada en la Universidad requiere que se modifiquen ciertas actitudes, el desarrollo de una gestión ambiental responsable, la creación de políticas convenientes y la evaluación de nuevas opciones tecnologías que impacten de manera positiva su implementación a través de las siguientes técnicas: • Mejoras en el proceso • Buenas prácticas operativas • Mantenimiento de equipos • Reutilización y reciclaje • Cambios en la materia prima • Cambios en la tecnología De esta manera los resultados presentarán un modelo transformador para la Institución, que permita su perdurabilidad, convirtiéndola en una Universidad pionera capaz de disminuir su impacto de operaciones en la sociedad.

Adopción de TIC como mecanismos facilitadores de la gestión organizacional

Los avances tecnológicos y la entrada a una nueva era digital son una realidad presente en todos los aspectos de la sociedad actual. El mundo organizacional se incluye en esta nueva era digital modernizando sus procesos y soportando sus actividades empresariales en tecnologías de la información y comunicaciones. La inclusión en la era digital por parte de las organizaciones es un paso importante que se debe dar para obtener los crecientes beneficios que la tecnología ofrece. Esta transformación organizacional hacia la implementación de herramientas TIC, como soporte del quehacer misional, debe darse bajo unos lineamientos de planeación estratégica e integración organizacional. Este estudio contiene una revisión conceptual con los lineamientos que una empresa debe tener en cuenta al momento de implementar herramientas TIC a sus áreas y actividades. Los hallazgos teóricos planteados son llevados a la realidad estudiando cómo empresas de Bogotá adoptan recursos tecnológicos. Los resultados principales del estudio muestran que la agrupación empresarial clasificada como gran empresa es el segmento que mejor aplica los lineamientos teóricos para la implementación correcta de herramientas TIC en un ambiente organizacional. El segmento de mediana y pequeña empresa da muestras de uso de herramientas TIC, sin embargo se nota una debilidad en la falta de planeación estratégica e integración de estos recursos tecnológicos al sistema organizacional. Esta investigación concluye mostrando un conjunto de recomendaciones y hallazgos de acuerdo a los datos analizados.

Aproximación a la asociatividad y la estructuración de redes basadas en confianza en instituciones prestadoras de servicios de salud

En este documento se concentra en un análisis sobre la asociatividad y la conformación de redes empresariales en dos instituciones prestadoras de servicios de salud del municipio de Tenjo Cundinamarca. En la primera parte se desarrolla el estado de la asociatividad con un enfoque de red, se plantea los objetivos, la justificación y los alcances de la investigación. En el segunda parte se hace alusión al marco teórico, marco legal, sistema general de seguridad social en salud, y la importancia que tiene las asociaciones empresariales, cooperación, participación y la confianza en las instituciones de salud; haciendo mención sobre clusters, alianzas y ecosistemas empresariales. En la tercera parte se realizó el marco metodológico de la investigación, análisis de resultado de las entrevistas, se describen las organizaciones objeto de este estudio. En la cuarta parte se realizan la discusión de la investigación, y se presentan las conclusiones que los autores de este estudio han presentado sobre la confianza fortalecida y la obligación prolongada de las empresas en el tiempo. Finamente, esta investigación presenta un punto de partida para la conformación de modelos que integren varias empresas, que puedan mejorar la competitividad, en las instituciones prestadoras de servicios de salud, permitiendo el acercando de los procesos del área administrativa con el área asistencia, en procura de brindar un mejoramiento continuo en la atención de los pacientes y su grupo familiar.