Very Intense Distinct Blue and Red Photoluminescence Emission in MgTiO3 Thin Films Prepared by the Polymeric Precursor Method: An Experimental and Theoretical Approach

MgTiO3 (MTO) thin films were prepared by the polymeric precursor method with posterior spin-coating deposition. The films were deposited on Pt(111)/Ti/SiO2/Si(100) substrates and heat treated at 350 degrees C for 2 h and then heat treated at 400, 450, 500, 550, 600, 650 and 700 C for 2 h. The degree of structural order disorder, optical properties, and morphology of the MTO thin films were investigated by X-ray diffraction (XRD), micro-Raman spectroscopy (MR), ultraviolet-visible (UV-vis) absorption spectroscopy, photoluminescence (PL) measurements, and field-emission gun scanning electron microscopy (FEG-SEM) to investigate the morphology. XRD revealed that an increase in the annealing temperature resulted in a structural organization of MTO thin films. First-principles quantum mechanical calculations based on density functional theory (B3LYP level) were employed to study the electronic structure of ordered and disordered asymmetric models. The electronic properties were analyzed, and the relevance of the present theoretical and experimental results was discussed in the light of PL behavior. The presence of localized electronic levels and a charge gradient in the band gap due to a break in the symmetry are responsible for the PL in disordered MTO lattice.

Polymorphic-induced transformations in CaTa2O6 single-crystal fibers obtained by laser-heated pedestal growth

Calcium tantalite (CaTa2O6) single crystal fibers were obtained by the laser-heated pedestal growth method (LHPG). At room temperature, this material can present three polymorphic modifications. The rapid crystallization inherent to the LHPG method produced samples within the Pm3 space group, with some chemical disorder. In order to check for polymorphic-induced transformations, the CaTa2O6 fibers have been submitted to different thermal treatments and investigated by micro-Raman spectroscopy. For short annealing times (15 min) at 1200 °C, the cubic modification was maintained, though with an improved crystalline quality, as evidenced by the enhanced inelastic scattered intensity (by ca. 250%) and narrowing of Raman bands. The polarized Raman spectra respected very well the predicted symmetries and the selection rules for this cubic modification. On the other hand, long annealing times (24 h) at 1200 °C led to a complete (irreversible) polymorphic transformation. The Raman bands became still more intense (ca. 15 times larger than for the as-grown fibers), narrower, and several new modes appeared. Also, the spectra became unpolarized, demonstrating a polycrystalline nature of the transformed crystals. The observed Raman modes could be fully assigned to an orthorhombic modification of CaTa2O6 belonging to the Pnma space group.

Influence of the network modifier on the characteristics of MSnO3 (M=Sr and Ca) thin films synthesized by chemical solution deposition

CaSnO3 and SrSnO3 alkaline earth stannate thin films were prepared by chemical solution deposition using the polymeric precursor method on various single crystal substrates (R- and C-sapphire and 100-SrTiO3) at different temperatures. The films were characterized by X-ray diffraction (θ-2θ, ω- and φ-scans), field emission scanning electron microscopy, atomic force microscopy, micro-Raman spectroscopy and photoluminescence. Epitaxial SrSnO3 and CaSnO3 thin films were obtained on SrTiO3 with a high crystalline quality. The long-range symmetry promoted a short-range disorder which led to photoluminescence in the epitaxial films. In contrast, the films deposited on sapphire exhibited a random polycrystalline growth with no meaningful emission regardless of the substrate orientation. The network modifier (Ca or Sr) and the substrate (sapphire or SrTiO3) influenced the crystallization process and/or the microstructure. Higher is the tilts of the SnO6 octahedra, as in CaSnO3, higher is the crystallization temperature, which changed also the nucleation/grain growth process.

Atmospheric corrosion of quaternary bronzes (Cu-Sn-Zn-Pb): laboratory tests (accelerated ageing in wet & dry conditions)and field studies (the Bottego monument in Parma, Italy).

The interactions between outdoor bronzes and the environment, which lead to bronze corrosion, require a better understanding in order to design effective conservation strategies in the Cultural Heritage field. In the present work, investigations on real patinas of the outdoor monument to Vittorio Bottego (Parma, Italy) and laboratory studies on accelerated corrosion testing of inhibited (by silane-based films, with and without ceria nanoparticles) and non-inhibited quaternary bronzes are reported and discussed. In particular, a wet&dry ageing method was used both for testing the efficiency of the inhibitor and for patinating bronze coupons before applying the inhibitor. A wide range of spectroscopic techniques has been used, for characterizing the core metal (SEM+EDS, XRF, AAS), the corroded surfaces (SEM+EDS, portable XRF, micro-Raman, ATR-IR, Py-GC-MS) and the ageing solutions (AAS). The main conclusions were: 1. The investigations on the Bottego monument confirmed the differentiation of the corrosion products as a function of the exposure geometry, already observed in previous works, further highlighting the need to take into account the different surface features when selecting conservation procedures such as the application of inhibitors (i.e. the relative Sn enrichment in unsheltered areas requires inhibitors which effectively interact not only with Cu but also with Sn). 2. The ageing (pre-patination) cycle on coupons was able to reproduce the relative Sn enrichment that actually happens in real patinated surfaces, making the bronze specimens representative of the real support for bronze inhibitors. 3. The non-toxic silane-based inhibitors display a good protective efficiency towards pre-patinated surfaces, differently from other widely used inhibitors such as benzotriazole (BTA) and its derivatives. 4. The 3-mercapto-propyl-trimethoxy-silane (PropS-SH) additivated with CeO2 nanoparticles generally offered a better corrosion protection than PropS-SH.

Sistemi multistrato per il miglioramento del comportamento tribologico dell'acciaio inossidabile AISI 316L: cementazione a bassa temperatura seguita da deposizione PACVD di carbonio amorfo (a-C:H)

Gli acciai inossidabili austenitici presentano ottime caratteristiche che li rendono ideali in tutti quei settori in cui è richiesta un’elevata resistenza alla corrosione associata a caratteristiche estetiche e funzionali. L’acciaio AISI 316L risulta essere uno dei più studiati ed utilizzati, specie nell’industria alimentare e farmaceutica, dove leapparecchiature debbono poter essere sottoposte ad aggressive procedure di sanificazione. Tuttavia, la modesta resistenza meccanica e la bassa durezza superficiale di questo acciaio determinano un comportamento non soddisfacente dal punto di vista dell’usura da strisciamento in assenza di lubrificanti, situazione che si verifica sovente in molti macchinari dedicati a queste industrie. Tra le varie soluzioni, studiate per migliorare il suo comportamento tribologico, la cementazione a bassa temperatura (LowTemperature Carburizing, LTC) seguita dalla deposizione PE-CVD (Plasma-Enhanced Chemical Vapour Deposition) di un rivestimento di carbonio amorfo idrogenato (a-C:H), sembra essere molto promettente. In questo lavoro vengono analizzate le caratteristiche tribologiche dell’acciaio AISI 316L cementato a bassa temperatura e rivestito di carbonio amorfo idrogenato, tramite prove tribologiche di strisciamento non lubrificato in geometria di contatto pattino su cilindro. Sono state verificate, inoltre, le caratteristiche microstrutturali e meccaniche superficiali del rivestimento multistrato LTC/a-C:H tramite osservazioni morfologiche/topografiche, analisi in spettroscopia micro-Raman e misure di indentazione strumentata sulle superfici rivestite, seguite da analisi metallografia e misura dei profili di microdurezza Vickers in sezione trasversale. I risultati ottenuti dimostrano che, ai fini di contenere l’effetto negativo legato all’aumento di rugosità dovuto al trattamento LTC, è opportuno effettuare una lucidatura precedente al trattamento stesso, poiché effettuandola successivamente si rischierebbe dicomprometterne lo strato efficace. Inoltre, si osserva come il trattamento LTC incrementi le capacità del substrato di supportare il rivestimento a-C:H, portando ad un miglioramento delle prestazioni tribologiche, nelle prove di strisciamento non lubrificato. Infine, si dimostra come l’utilizzo di un rivestimento a base di carbonio amorfo idrogenato adeguatamente supportato permetta una riduzione dell’attrito (di oltre cinque volte) e dell’usura (di circa dieci ordini di grandezza) rispetto ai corrispondenti materiali non rivestiti.

Biomaterials for Clinical Application in Endodontics

Endodontic therapy consists in the management of several tissues such as pulp tissue, periodontal tissue, periapical bone and dentine. These tissues are often contaminated by blood, periapical exudates and biological fluids. An ideal orthograde or retrograde filling material should be non toxic, noncarcinogenic, nongenotoxic, biocompatible with the host tissues, insoluble in tissue fluids, and dimensionally stable. Calcium-silicate MTA based cements own many of these ideal characteristics, but the long setting time, the non-easy handling and the lack of mechanical properties at early times are few drawbacks which may complicate the clinical application. The aim of this study was to investigate the chemical, physical and biological properties of calcium-silicate MTA cements in order to improve the mechanical properties and the handling keeping the biological characteristics unchanged. Chemical and physical properties such as setting time, solubility, water-uptake, ion release, sealing ability were investigated according the ISO and ADA specifications. The bioactivity (ability to produce apatite nano-sferulities) of MTA cements were evaluated using ESEM/EDX, micro-Raman and ATR/FTIR spettroscopy.

Charakterisierung antiker Keramik und ihrer Herstellungstechniken mit mineralogischen Methoden am Beispiel Mayener Gebrauchskeramik

Mehr als hundert Jahre archäologischer Forschung haben gezeigt, dass in Mayen in römischer und mittelalterlicher Zeit eines der wichtigsten europäischen Produktionszentren für die Herstellung qualitätsvoller Gebrauchskeramik bestand. Im Rahmen dieser Studie wurden vier Befundkomplexe aus Töpfereisiedlungen vom 4. bis in das 14. Jahrhundert untersucht. Genauer handelt es sich um Keramik aus zwei spätantiken Brennanlagen des 4. Jahrhunderts im Bereich der Flur „Auf der Eich“ an den Straßen „Am Sonnenhang“ und „Frankenstraße“. Weiterhin konnte Material aus zwei Töpferofenfüllungen des 5. bis 9. Jahrhunderts analysiert werden, das 1975 auf dem Grundstück 55 an der „Siegfriedstraße“ in Brennanlagen entdeckt wurde. Hinzu kam Brenngut aus elf Töpferöfen des späten 8. bis 14. Jahrhunderts, welches in den so genannten „Burggärten“ der Genovevaburg von Mayen in den Jahren 1986/87 durch die archäologische Denkmalpflege in Koblenz geborgen wurde. Die mineralogischen Untersuchungen zur Charakterisierung der „Mayener Keramik“ wurden systematisch an den Keramikmaterialien aus diesen Fundstellen durchgeführt. Mittelalterliche Keramik aus Bornheim-Walberberg, Brühl-Eckdorf, Höhr-Grenzhausen, Langerwehe, Frechen, Brühl-Pingsdorf, Paffrath, Raeren, Ratingen-Breitscheid, Siegburg-Seehofstraße, Siegburg-Scherbenhügel, Fredelsloh und Brühl-Badorf konnte für diese Arbeit als Referenzmaterialien ebenfalls untersucht werden. Provenienzanalysen wurden an Keramikproben aus 27 Fundorten, die makroskopisch nach Mayener Ware aussehen, mit mineralogischen Methoden durchgeführt, um sie der Fundregion Mayen eindeutig zuordnen zu können.rnPhasenanalyse, chemische Analyse und thermische Analyse wurden an Keramik sowie Ton durchgeführt. Die Phasenanalyse wurde zur Bestimmung der mineralischen Zusammensetzung von Grundmasse und Magerungsmittel (Röntgendiffraktometrie (XRD), Polarisationsmikroskop, Mikro-Raman-Spektroskopie) verwendet. Die chemische Zusammensetzung wurde durch Röntgenfluoreszenzanalyse (RFA) ermittelt. Elektronenstrahlmikroanalyse (ESMA) und Laser-Massenspektrometrie mit induktiv gekoppeltem Plasma (LA-ICP-MS) wurden bei den Proben, bei denen weniger als 2g Material zur Verfügung standen, eingesetzt. Brennexperimente wurden am originalen Rohstoff der Keramik aus den „Burggärten“ der Genovevaburg durchgeführt. Gebrannter Ton wurde durch Röntgendiffraktometrie (XRD), Infrarotspektroskopie (IR) und Differential-Thermoanalyse (DTA) analysiert. rnAnhand der Messergebnisse lässt sich die Mayener Keramik aus den vier Fundplätzen in zwei Typen zusammenzufassen: der mit Feldspat-reichem Sand gemagerte römische Typ und der mit Quarz-reichem Sand gemagerte mittelalterliche Typ. Die Änderung des Magerungsmittels von Feldspat- zu Quarzsand weist eine technische Entwicklung zu höheren Brenntemperaturen von der Römerzeit bis in das Mittelalter nach. Nach der Untersuchung und dem Vergleich mit den Referenzkeramikgruppen ist festzustellen, dass durch multivariate Statistikanalysen der chemischen Komponenten die Charakterisierung der Keramik und eine Differenzierung zwischen den Keramikgruppen gelingt. Diese Erkenntnisse bildeten die Basis für Provenienzanalysen. 16 Fundorte können durch Provenienzanalyse sicher als Exportregionen der Mayener Ware festgestellt werden. Gemäß den Brennexperimenten lassen sich die chemischen Reaktionen während des Brandprozesses nachvollziehen. Zwei Methoden wurden mittels Röntgendiffraktometrie (XRD) und Differential-Thermoanalyse (DTA) zur Bestimmung der Brenntemperaturen der Keramik modelliert. Die Töpferöfen der „Burggärten“ können nach der Brenntemperatur in zwei Typen zusammengefasst werden: solche mit einer Brenntemperatur unter 1050°C und solche mit einer Brenntemperatur über 1050°C.rn

Internal characteristics, chemical compounds and spectroscopy of sapphire as single crystals

In this study more than 450 natural sapphire samples (most of basaltic type) collected from 19 different areas were examined. They are from Dak Nong, Dak Lak, Quy Chau, two unknown sources from the north (Vietnam); Bo Ploi, Khao Ploi Waen (Thailand); Ban Huay Sai (Laos); Australia; Shandong (China); Andapa, Antsirabe, Nosibe (Madagascar); Ballapana (Sri Lanka); Brazil; Russia; Colombia; Tansania and Malawi. rnThe samples were studied on internal characteristics, chemical compositions, Raman-, luminescence-, Fourier transform infrared (FTIR)-, and ultraviolet-visible-near infrared (UV-Vis-NIR)- spectroscopy. The internal features of these sapphire samples were observed and identified by gemological microscope, con focal micro Raman and FTIR spectroscopy. The major and minor elements of the samples were determined by electron probe microanalysis (EPMA) and the trace elements by laser ablation inductively coupled plasma mass spectrometry (LA-ICP-MS). rnThe structural spectra of sapphire were investigated by con focal Raman spectroscopy. The FTIR spectroscopy was used to study the vibration modes of OH-groups and also to determine hydrous mineral inclusions in sapphire. The UV-Vis-NIR absorption spectroscopy was used to analyze the cause of sapphire color. rnNatural sapphires contain many types of mineral inclusions. Typically, they are iron-containing inclusions like goethite, ilmenite, hematite, magnetite or silicate minerals commonly feldspar, and often observed in sapphires from Asia countries, like Dak Nong, Dak Lak in the south of Vietnam, Ban Huay Sai (Laos), Khao Ploi Waen and Bo Ploi (Thailand) or Shandong (China). Meanwhile, CO2-diaspore inclusions are normally found in sapphires from Tansania, Colombia, or the north of Vietnam like Quy Chau. rnIron is the most dominant element in sapphire, up to 1.95 wt.% Fe2O3 measured by EPMA and it affects spectral characteristics of sapphire.rnThe Raman spectra of sapphire contain seven peaks (2A1g + 5Eg). Two peaks at about 418.3 cm-1 and 577.7 cm-1 are influenced by high iron content. These two peaks shift towards smaller wavenumbers corresponding to increasing iron content. This shift is showed by two equations y(418.3)=418.29-0.53x andy(577.7)=577.96-0.75x, in which y is peak position (cm-1) and x is Fe2O3 content (wt.%). By exploiting two these equations one can estimate the Fe2O3 contents of sapphire or corundum by identifying the respective Raman peak positions. Determining the Fe2O3 content in sapphire can help to distinguish sapphires from different origins, e.g. magmatic and metamorphic sapphire. rnThe luminescence of sapphire is characterized by two R-lines: R1 at about 694 nm and R2 at about 692 nm. This characteristic is also influenced by high iron content. The peak positions of two R-lines shift towards to smaller wavelengths corresponding to increasing of iron content. This correlation is showed by two equations y(R_2 )=692.86-0.049x and y(R_1 )=694.29-0.047x, in which y is peak position (nm) of respective R-lines and x is Fe2O3 content (wt.%). Two these equations can be applied to estimate the Fe2O3 content of sapphire and help to separate sapphires from different origins. The luminescence is also applied for determination of the remnant pressure or stress around inclusions in Cr3+-containing corundum by calibrating a 0-pressure position in experimental techniques.rnThe infrared spectra show the presence of vibrations originating from OH-groups and hydrous mineral inclusions in the range of 2500-4000 cm-1. Iron has also an effect upon the main and strongest peak at about 3310 cm-1. The 3310 cm-1 peak is shifted to higher wavenumber when iron content increases. This relationship is expressed by the equation y(3310)=0.92x+3309.17, in which y is peak position of the 3310 cm-1 and x is Fe2O3 content (wt.%). Similar to the obtained results in Raman and luminescence spectra, this expression can be used to estimate the Fe2O3 content and separate sapphires from different origins. rnThe UV-Vis-NIR absorption spectra point out the strong and sharp peaks at about 377, 387, and 450 nm related to dispersed Fe3+, a broad band around 557 and 600 nm related to intervalence charge transfer (IVCT) Fe2+/Ti4+, and a broader band around 863 nm related to IVCT of Fe2+/Fe3+. rnGenerally, sapphires from different localities were completely investigated on internal features, chemical compounds, and solid spectral characteristics. The results in each part contribute for identifying the iron content and separate sapphires from different localities order origins. rn

Fotocatalizzatori di seconda generazione: sintesi e indagine strutturale su nanoparticelle di Ti1-xVxO2

Il TiO2 è probabilmente il fotocatalizzatore maggiormente studiato in letteratura a partire già dagli anni settanta. Le applicazioni più rilevanti dei dispositivi fotocatalitici sono in campo ambientale (depurazione delle acque da inquinanti quali coloranti, microbatteri e residui metallici) e nella produzione di "solar fuel" (combustibili solari), fra questi l'idrogeno. L'idrogeno come vettore energetico è eco-compatibile e può essere utilizzato come carburante il cui prodotto di scarto è vapor d'acqua. Il biossido di titanio è uno dei materiali più promettenti per la costruzione di celle fotocatalitiche, grazie alla sua biocompatibilità e resistenza alla corrosione in ambiente acquoso. Il limite principale di questo materiale è legato allo scarso assorbimento nel visibile dovuto al band gap troppo elevato (circa 3.2 eV). Fra le varie strategie per superare questo problema, è stato mostrato che opportuni droganti permettono di incrementare la "Visible Light Activity", portando ai cosiddetti fotocatalizzatori di 2a generazione. I droganti più promettenti sono il vanadio e l'azoto che possono essere utilizzati singolarmente o in co-doping. L'inserimento di questi materiali nella matrice di TiO2 porta a un notevole miglioramento dei dispositivi abbassando il valore di band gap e permettendo un maggiore assorbimento nello spettro solare. Scopo di questa tesi è lo studio dei processi di crescita di film nanoparticellari di TiO2 drogato con vanadio. La tecnica di crescita usata è la Condensazione in Gas Inerte (IGC), mentre per l'indagine di morfologia e composizione ci si è serviti della microscopia elettronica. Con l'ausilio della diffrazione di raggi X è stato possibile controllare lo stato di cristallizzazione e determinare a quali temperature di trattamento in atmosfera ossidante avviene quest'ultima. Tramite le misure micro-Raman effettuate presso i laboratori dell'Università di Trento è stato possibile monitorare l'andamento della cristallizzazione di campioni depositati con parametri di evaporazione differenti (presenza di ossigeno o meno nell'atmosfera di evaporazione), evidenziando un maggior controllo sulla fase cristallina ottenuta per i campioni cresciuti in atmosfera ricca di ossigeno. Sono state effettuate analisi strutturali avanzate presso i laboratori ESRF di Grenoble, dove sono state portate avanti misure di assorbimento di raggi X di tipo EXAFS e XANES sulla soglia del titanio e del vanadio, evidenziando il carattere sostituzionale del vanadio all'interno della matrice di TiO2 e le diverse fasi di cristallizzazione.

Looking at Chemistry in Hard to See Places: Understanding Energy Conversion at 1400° Celsius

Solid oxide fuel cells (SOFCs) are promising devices for stationary and portable power and heat generation, because they can use complex fuels such as hydro-carbons, CO, and alcohols. Extreme, non-equilibrium conditions and high tem-peratures (≥ 700 ˚C) required for SOFC operation hamper efforts to understand the mechanisms of component degradation in SOFCs. This talk focuses on new insights into SOFC chemistry and the conversion of carbon-containing fuels (both hydrocarbons and oxygenated) into electricity, carbon dioxide and water, gleaned from a combination of techniques including electrochemical impedance spectroscopy, voltammetry, and vibrational Raman scattering.

Chemical compositions of solid particles present in the Greenland NEEM ice core over the last 110,000 years

This study reports the chemical composition of particles present along Greenland’s North Greenland Eemian Ice Drilling (NEEM) ice core, back to 110,000 years before present. Insoluble and soluble particles larger than 0.45 μm were extracted from the ice core by ice sublimation, and their chemical composition was analyzed using scanning electron microscope and energy dispersive X-ray spectroscopy and micro-Raman spectroscopy. We show that the dominant insoluble components are silicates, whereas NaCl, Na₂SO₄, CaSO ₄, and CaCO₃ represent major soluble salts. For the first time, particles of CaMg(CO₃)₂ and Ca(NO₃)₂ 4H₂O are identified in a Greenland ice core. The chemical speciation of salts varies with past climatic conditions. Whereas the fraction of Na salts (NaCl + Na₂SO₄) exceeds that of Ca salts (CaSO₄+ CaCO₃) during the Holocene (0.6–11.7 kyr B.P.), the two fractions are similar during the Bølling-Allerød period (12.9–14.6 kyr B.P.). During cold climate such as over the Younger Dryas (12.0–12.6 kyr B.P.) and the Last Glacial Maximum (15.0–26.9 kyr B.P.), the fraction of Ca salts exceeds that of Na salts, showing that the most abundant ion generally controls the salt budget in each period. High-resolution analyses reveal changing particle compositions: those in Holocene ice show seasonal changes, and those in LGM ice show a difference between cloudy bands and clear layers, which again can be largely explained by the availability of ionic components in the atmospheric aerosol body of air masses reaching Greenland.

Properties of seawater and particulate matter from a WETLabs ALFA hyperspectral laser spectrofluorometer mounted on the continuous surface water sampling system during the Tara Oceans expedition 2009-2013

The Tara Oceans Expedition (2009-2013) sampled the world oceans on board a 36 m long schooner, collecting environmental data and organisms from viruses to planktonic metazoans for later analyses using modern sequencing and state-of-the-art imaging technologies. Tara Oceans Data are particularly suited to study the genetic, morphological and functional diversity of plankton. The present data set provides continuous measurements made with an Aquatic Laser Fluorescence Analyzer (ALFA) (Chekalyuk et al., 2014), connected in-line to the TARA flow through system during 2013. The ALFA instrument provides dual-wavelength excitation (405 and 514 nm) of laser-stimulated emission (LSE) for spectral and temporal analysis. It offers in vivo fluorescence assessments of phytoplankton pigments, biomass, photosynthetic yield (Fv/Fm), phycobiliprotein (PBP)-containing phytoplankton groups, and chromophoric dissolved organic matter (CDOM) (Chekalyuk and Hafez, 2008; 2013A). Spectral deconvolution (SDC) is used to assess the overlapped spectral bands of aquatic fluorescence constituents and water Raman scattering (R). The Fv/Fm measurements are spectrally corrected for non-chlorophyll fluorescence background produced by CDOM and other constituents (Chekalyuk and Hafez, 2008). The sensor was cleaned weakly following the manufacturer recommended protocol.

Estudio de limitaciones en sistemas WDM

Los avances tecnológicos de los últimos años han modificado el panorama de las comunicaciones ópticas. Los amplificadores EDFA (Erbium-Doped Fiber Amplifier) han alterado dos aspectos fundamentales de los sistemas WDM (Wavelength Division Multiplexing): el aumento considerable de las distancias de regeneración y además, la tecnología WDM es un medio más económico de incrementar la capacidad de los sistemas que la tecnología TDM (Time Division Multiplexing). Sin embargo, la implementación de sistemas WDM con grandes tramos sin regeneración de señal óptica trae consigo la aparición de nuevos problemas, entre los que se encuentran las no-linealidades en fibra óptica. Estas no-linealidades en fibras de sílice se pueden clasificar en dos categorías: dispersión estimulada (de Raman y de Brillouin) y efectos debidos al índice no lineal de refracción (automodulación y modulación cruzada de fase y mezcla de cuatro ondas). Este Proyecto Fin de Carrera pretende ser un estudio teórico que refleje el actual Estado del Arte de los principales efectos no-lineales que se producen en los sistemas WDM: dispersión estimulada de Raman (SRS, Stimulated Raman Scattering), dispersión estimulada de Brillouin (SBS,Stimulated Brilfouin Scattering), automodulación de fase (SPM, Self-Phase Modulation), modulación cruzada de fase (XPM, Cross-Phase Modulation) y mezcla de cuatro ondas (FWM, Four-Wave Mixing).

Experimental and numerical study of cw green laser crystallization of a-Si:H thin films

Crystallization and grain growth technique of thin film silicon are among the most promising methods for improving efficiency and lowering cost of solar cells. A major advantage of laser crystallization and annealing over conventional heating methods is its ability to limit rapid heating and cooling to thin surface layers. Laser energy is used to heat the amorphous silicon thin film, melting it and changing the microstructure to polycrystalline silicon (poly-Si) as it cools. Depending on the laser density, the vaporization temperature can be reached at the center of the irradiated area. In these cases ablation effects are expected and the annealing process becomes ineffective. The heating process in the a-Si thin film is governed by the general heat transfer equation. The two dimensional non-linear heat transfer equation with a moving heat source is solve numerically using the finite element method (FEM), particularly COMSOL Multiphysics. The numerical model help to establish the density and the process speed range needed to assure the melting and crystallization without damage or ablation of the silicon surface. The samples of a-Si obtained by physical vapour deposition were irradiated with a cw-green laser source (Millennia Prime from Newport-Spectra) that delivers up to 15 W of average power. The morphology of the irradiated area was characterized by confocal laser scanning microscopy (Leica DCM3D) and Scanning Electron Microscopy (SEM Hitachi 3000N). The structural properties were studied by micro-Raman spectroscopy (Renishaw, inVia Raman microscope).

Thermal, stress, and traps effects in AlGaN/GaN HEMTs

GaN y AlN son materiales semiconductores piezoeléctricos del grupo III-V. La heterounión AlGaN/GaN presenta una elevada carga de polarización tanto piezoeléctrica como espontánea en la intercara, lo que genera en su cercanía un 2DEG de grandes concentración y movilidad. Este 2DEG produce una muy alta potencia de salida, que a su vez genera una elevada temperatura de red. Las tensiones de puerta y drenador provocan un stress piezoeléctrico inverso, que puede afectar a la carga de polarización piezoeléctrica y así influir la densidad 2DEG y las características de salida. Por tanto, la física del dispositivo es relevante para todos sus aspectos eléctricos, térmicos y mecánicos. En esta tesis se utiliza el software comercial COMSOL, basado en el método de elementos finitos (FEM), para simular el comportamiento integral electro-térmico, electro-mecánico y electro-térmico-mecánico de los HEMTs de GaN. Las partes de acoplamiento incluyen el modelo de deriva y difusión para el transporte electrónico, la conducción térmica y el efecto piezoeléctrico. Mediante simulaciones y algunas caracterizaciones experimentales de los dispositivos, hemos analizado los efectos térmicos, de deformación y de trampas. Se ha estudiado el impacto de la geometría del dispositivo en su auto-calentamiento mediante simulaciones electro-térmicas y algunas caracterizaciones eléctricas. Entre los resultados más sobresalientes, encontramos que para la misma potencia de salida la distancia entre los contactos de puerta y drenador influye en generación de calor en el canal, y así en su temperatura. El diamante posee une elevada conductividad térmica. Integrando el diamante en el dispositivo se puede dispersar el calor producido y así reducir el auto-calentamiento, al respecto de lo cual se han realizado diversas simulaciones electro-térmicas. Si la integración del diamante es en la parte superior del transistor, los factores determinantes para la capacidad disipadora son el espesor de la capa de diamante, su conductividad térmica y su distancia a la fuente de calor. Este procedimiento de disipación superior también puede reducir el impacto de la barrera térmica de intercara entre la capa adaptadora (buffer) y el substrato. La muy reducida conductividad eléctrica del diamante permite que pueda contactar directamente el metal de puerta (muy cercano a la fuente de calor), lo que resulta muy conveniente para reducir el auto-calentamiento del dispositivo con polarización pulsada. Por otra parte se simuló el dispositivo con diamante depositado en surcos atacados sobre el sustrato como caminos de disipación de calor (disipador posterior). Aquí aparece una competencia de factores que influyen en la capacidad de disipación, a saber, el surco atacado contribuye a aumentar la temperatura del dispositivo debido al pequeño tamaño del disipador, mientras que el diamante disminuiría esa temperatura gracias a su elevada conductividad térmica. Por tanto, se precisan capas de diamante relativamente gruesas para reducer ele efecto de auto-calentamiento. Se comparó la simulación de la deformación local en el borde de la puerta del lado cercano al drenador con estructuras de puerta estándar y con field plate, que podrían ser muy relevantes respecto a fallos mecánicos del dispositivo. Otras simulaciones se enfocaron al efecto de la deformación intrínseca de la capa de diamante en el comportamiento eléctrico del dispositivo. Se han comparado los resultados de las simulaciones de la deformación y las características eléctricas de salida con datos experimentales obtenidos por espectroscopía micro-Raman y medidas eléctricas, respectivamente. Los resultados muestran el stress intrínseco en la capa producido por la distribución no uniforme del 2DEG en el canal y la región de acceso. Además de aumentar la potencia de salida del dispositivo, la deformación intrínseca en la capa de diamante podría mejorar la fiabilidad del dispositivo modulando la deformación local en el borde de la puerta del lado del drenador. Finalmente, también se han simulado en este trabajo los efectos de trampas localizados en la superficie, el buffer y la barrera. Las medidas pulsadas muestran que tanto las puertas largas como las grandes separaciones entre los contactos de puerta y drenador aumentan el cociente entre la corriente pulsada frente a la corriente continua (lag ratio), es decir, disminuir el colapse de corriente (current collapse). Este efecto ha sido explicado mediante las simulaciones de los efectos de trampa de superficie. Por su parte, las referidas a trampas en el buffer se enfocaron en los efectos de atrapamiento dinámico, y su impacto en el auto-calentamiento del dispositivo. Se presenta también un modelo que describe el atrapamiento y liberación de trampas en la barrera: mientras que el atrapamiento se debe a un túnel directo del electrón desde el metal de puerta, el desatrapamiento consiste en la emisión del electrón en la banda de conducción mediante túnel asistido por fonones. El modelo también simula la corriente de puerta, debida a la emisión electrónica dependiente de la temperatura y el campo eléctrico. Además, también se ilustra la corriente de drenador dependiente de la temperatura y el campo eléctrico. ABSTRACT GaN and AlN are group III-V piezoelectric semiconductor materials. The AlGaN/GaN heterojunction presents large piezoelectric and spontaneous polarization charge at the interface, leading to high 2DEG density close to the interface. A high power output would be obtained due to the high 2DEG density and mobility, which leads to elevated lattice temperature. The gate and drain biases induce converse piezoelectric stress that can influence the piezoelectric polarization charge and further influence the 2DEG density and output characteristics. Therefore, the device physics is relevant to all the electrical, thermal, and mechanical aspects. In this dissertation, by using the commercial finite-element-method (FEM) software COMSOL, we achieved the GaN HEMTs simulation with electro-thermal, electro-mechanical, and electro-thermo-mechanical full coupling. The coupling parts include the drift-diffusion model for the electron transport, the thermal conduction, and the piezoelectric effect. By simulations and some experimental characterizations, we have studied the device thermal, stress, and traps effects described in the following. The device geometry impact on the self-heating was studied by electro-thermal simulations and electrical characterizations. Among the obtained interesting results, we found that, for same power output, the distance between the gate and drain contact can influence distribution of the heat generation in the channel and thus influence the channel temperature. Diamond possesses high thermal conductivity. Integrated diamond with the device can spread the generated heat and thus potentially reduce the device self-heating effect. Electro-thermal simulations on this topic were performed. For the diamond integration on top of the device (top-side heat spreading), the determinant factors for the heat spreading ability are the diamond thickness, its thermal conductivity, and its distance to the heat source. The top-side heat spreading can also reduce the impact of thermal boundary resistance between the buffer and the substrate on the device thermal behavior. The very low electrical conductivity of diamond allows that it can directly contact the gate metal (which is very close to the heat source), being quite convenient to reduce the self-heating for the device under pulsed bias. Also, the diamond coated in vias etched in the substrate as heat spreading path (back-side heat spreading) was simulated. A competing mechanism influences the heat spreading ability, i.e., the etched vias would increase the device temperature due to the reduced heat sink while the coated diamond would decrease the device temperature due to its higher thermal conductivity. Therefore, relative thick coated diamond is needed in order to reduce the self-heating effect. The simulated local stress at the gate edge of the drain side for the device with standard and field plate gate structure were compared, which would be relevant to the device mechanical failure. Other stress simulations focused on the intrinsic stress in the diamond capping layer impact on the device electrical behaviors. The simulated stress and electrical output characteristics were compared to experimental data obtained by micro-Raman spectroscopy and electrical characterization, respectively. Results showed that the intrinsic stress in the capping layer caused the non-uniform distribution of 2DEG in the channel and the access region. Besides the enhancement of the device power output, intrinsic stress in the capping layer can potentially improve the device reliability by modulating the local stress at the gate edge of the drain side. Finally, the surface, buffer, and barrier traps effects were simulated in this work. Pulsed measurements showed that long gates and distances between gate and drain contact can increase the gate lag ratio (decrease the current collapse). This was explained by simulations on the surface traps effect. The simulations on buffer traps effects focused on illustrating the dynamic trapping/detrapping in the buffer and the self-heating impact on the device transient drain current. A model was presented to describe the trapping and detrapping in the barrier. The trapping was the electron direct tunneling from the gate metal while the detrapping was the electron emission into the conduction band described by phonon-assisted tunneling. The reverse gate current was simulated based on this model, whose mechanism can be attributed to the temperature and electric field dependent electron emission in the barrier. Furthermore, the mechanism of the device bias via the self-heating and electric field impact on the electron emission and the transient drain current were also illustrated.