Processability, hardness, andmagnetic properties of rubber ferrite composites containingmanganese zinc ferrites

Rubber ferrite composites have the unique advantage of mouldability, which is not easily obtainable using ceramic magnetic materials. The incorporation of mixed ferrites in appropriate weight ratios into the rubber matrix not only modi es the dielectric properties of the composite but also imparts magnetic properties to it. Mixed ferrites belonging to the series of Mn(1 – x )Znx Fe2O4 have been synthesised with diVerent values of x in steps of 0·2, using conventional ceramic processing techniques. Rubber ferrite composites were prepared by the incorporation of these pre-characterised polycrystallineMn(1 – x )Znx Fe2O4 ceramics into a natural rubber matrix at diVerent loadings according to a speci c recipe. The processability of these elastomers was determined by investigating their cure characteristics. The magnetic properties of the ceramic llers as well as of the rubber ferrite composites were evaluated and the results were correlated. Studies of the magnetic properties of these rubber ferrite composites indicate that the magnetisation increases with loading of the ller without changing the coercive eld. The hardness of these composites shows a steady increase with the loading of the magnetic llers. The evaluation of hardness andmagnetic characteristics indicates that composites with optimummagnetisation and almost minimum stiVness can be achieved with a maximum loading of 120 phr of the ller at x=0·4. From the data on the magnetisation of the composites, a simple relationship connecting the magnetisation of the rubber ferrite composite and the ller was formulated. This can be used to synthesise rubber ferrite composites with predetermined magnetic properties

Dielectric andmechanical properties of rubber ferrite composites

Rubber ferrite composites (RFCs) containing powdered nickel zinc ferrite (Ni1 – xZnxFe2O4 ) in a natural rubber matrix have been prepared and their mechanical and dielectric properties have been evaluated. Variations in the relative permittivity of both the ferrite ceramics and RFCs have been studied over a range of frequencies, ceramic compositions, ceramic ller loadings, and temperatures, and the results have been correlated. Appropriate mixture equations have been formulated to calculate the dielectric permittivity of the composite from the dielectric permittivity of its constituents. Values calculated using these equations have been compared with experimental data on relative permittivity, and the two have been found to be in good agreement. In the present investigationit was also observed that for x=0·4 and for the maximum ferrite loading, the composite sample exhibits maximum magnetisation and optimum exibility

Processability And Magnetic Properties Of Rubber Ferrite Composites Containing Barium Ferrite

Rubber ferrite composites (RFC) are magnetic polymer composites and have a variety of applications as flexible magnets, pressure=photo sensors, and microwave absorbers. The mouldability into complex shapes is one of the advantages of these magnetic elastomers. They have the potential of replacing the conventional ceramic materials, due to theire flexible nature. In the present study, the incorporation of pre-characterized hexagonal ferrites, namely barium ferrite (BaFe12O19), into natural rubber matrix is carried out according to a suitable recipe for various loadings of the filler. The processability of these compounds was determined by evaluating the cure characteristics: scorch time, cure time, and minimum and maximum torque. It has been found that the addition of magnetic fillers does not affect the processability of the composites, whereas the physical properties are modified. The magnetic properties of these composites containing various loadings of the magnetic filler were also investigated. The magnetic properties of RFC can be controlled by the addition of appropriate amount of the ferrite filler.

Magnetic and processability studies of nitrile rubber vulcanisates containing barium ferrite and carbon black

Fine particles of barium ferrite (BaFe12O19) belonging to the M-type hexagonal ferrites were prepared by the conventional ceramic techniques. They were incorporated into a nitrile rubber matrix according to a specific recipe for various loadings to produce rubber ferrite composites (RFC). The percolation threshold is not reached for a maximum loading of 130 phr (parts per hundred rubber). Here in this paper, the magnetic properties and processability of the nitrile rubber based RFCs containing barium ferrite (BaF) and HAF carbon black is reported. The magnetic properties of the ceramic ferrite and these rubber ferrite composites were evaluated and it was found that the coercivity values of RFCs were less than that of the ceramic BaF, but remained constant with the loading of both the ferrite filler and carbon black. However, other properties like saturation magnetization and magnetic remanence increased with the loading of ferrite filler.

Biobutanol from lignocellulosic biomass by a novel Clostridium sporogenes BE01

In the current study, a novel non-acetone forming butanol and ethanol producer Was isolated and identified. Based on the 16s rDNA sequence BLAST and phylogenetic analyses, it was found to have high similarity with the reported hydrogen producing strains of Clostridium sporogenes. Biochemical studies revealed that it is lipase and protease positive. The lipolytic and proteolytic properties are the very important characteristics of Clostridium sporogenes. Sugar utilization profile studies were positive for glucose, saccharose, cellobiose and weakly positive result to xylose. This study demonstrated C. sporogenes BE01, an isolate from NIIST is having potential to compete with existing, well known butanol producers with the advantage of no acetone in the final solvent mixture. Rice straw hydrolysate is a potent source of substrate for butanol production by C. sporogenes BE01. Additional supplementation of vitamins and minerals were avoided by using rice straw hydrolysate as substrate. Its less growth, due to the inhibitors present in the hydrolysate and also inhibition by products resulted in less efficient conversion of sugars to butanol. Calcium carbonate played an important role in improving the butanol production, by providing the buffering action during fermentation and stimulating the electron transport mediators and redox reactions favoring butanol production. Its capability to produce acetic acid, butyric acid and hydrogen in significant quantities during butanol production adds value to the conversion process of lignocellulosic biomass to butanol. High cell density fermentation by immobilizing the cells on to ceramic particles improved the solvents and VFA production. Reduced sugar utilization from the concentrated hydrolysate could be due to accumulation of inhibitors in the hydrolysate during concentration. Two-stage fermentation was very efficient with immobilized cells and high conversions of sugars to solvents and VFAs were achieved. The information obtained from the study would be useful to develop a feasible technology for conversion of lignocellulosic biomass to biobutanol.

Magnetische Kopplungen in magneto-optischen Speicherschichten

Im Rahmen dieser Arbeit wurden magneto-optische Speicherschichten und ihre Kopplungen untereinander untersucht. Hierzu wurden zum Einen die für die magneto-optische Speichertechnologie "klassischen" Schichten aus RE/TM-Legierungen verwendet, zum Anderen aber auch erfolgreich Granate integriert, die bisher nicht in diesem Anwendungsgebiet verwendet wurden. Einleitend werden die magneto-optischen Verfahren, die resultierenden Anforderungen an die dünnen Schichten und die entsprechenden physikalischen Grundlagen diskutiert. Außerdem wird auf das Hochfrequenz-Sputtern von RE/TM-Legierungen eingegangen und die verwendeten magneto-optischen Messverfahren werden erläutert [Kap. 2 & 3]. Die Untersuchungen an RE/TM-Schichten bestätigen die aus der Literatur bekannten Eigenschaften. Sie lassen sich effektiv, und für magneto-optische Anwendungen geeignet, über RF-Sputtern herstellen. Die unmittelbaren Schicht-Parameter, wie Schichtdicke und Terbium-Konzentration, lassen sich über einfache Zusammenhänge einstellen. Da die Terbium-Konzentration eine Änderung der Kompensationstemperatur bewirkt, lässt sich diese mit Messungen am Kerr-Magnetometer überprüfen. Die für die Anwendung interessante senkrechte magnetische Anisotropie konnte ebenfalls mit den Herstellungsbedingungen verknüpft werden. Bei der Herstellung der Schichten auf einer glatten Glas-Oberfläche (Floatglas) zeigt die RE/TM-Schicht bereits in den ersten Lagen ein Wachstumsverhalten, das eine senkrechte Anisotropie bewirkt. Auf einer Quarzglas- oder Keramik-Oberfläche wachsen die ersten Lagen in einer durch das Substrat induzierten Struktur auf, danach ändert sich das Wachstumsverhalten stetig, bis eine senkrechte Anisotropie erreicht wird. Dieses Verhalten kann auch durch verschiedene Pufferschichten (Aluminium und Siliziumnitrid) nur unwesentlich beeinflusst werden [Kap. 5 & Kap. 6]. Bei der direkten Aufbringung von Doppelschichten, bestehend aus einer Auslese-Schicht (GdFeCo) auf einer Speicherschicht (TbFeCo), wurde die Austausch-Kopplung demonstriert. Die Ausleseschicht zeigt unterhalb der Kompensationstemperatur keine Kopplung an die Speicherschicht, während oberhalb der Kompensationstemperatur eine direkte Kopplung der Untergitter stattfindet. Daraus ergibt sich das für den MSR-Effekt erwünschte Maskierungsverhalten. Die vorher aus den Einzelschichten gewonnen Ergebnisse zu Kompensationstemperatur und Wachstumsverhalten konnten in den Doppelschichten wiedergefunden werden. Als Idealfall erweist sich hier die einfachste Struktur. Man bringt die Speicherschicht auf Floatglas auf und bedeckt diese direkt mit der Ausleseschicht [Kap. 7]. Weiterhin konnte gezeigt werden, dass es möglich ist, den Faraday-Effekt einer Granatschicht als verstärkendes Element zu nutzen. Im anwendungstauglichen, integrierten Schichtsystem konnten die kostengünstig, mit dem Sol-Gel-Verfahren produzierten, Granate die strukturellen Anforderungen nicht erfüllen, da sich während der Herstellung Risse und Löcher gebildet haben. Bei der experimentellen Realisierung mit einer einkristallinen Granatschicht und einer RE/TM-Schicht konnte die prinzipielle Eignung des Schichtsystems demonstriert werden [Kap. 8].

Piezoelectric Ultrasonic Micromotors

This report describes development of micro-fabricated piezoelectric ultrasonic motors and bulk-ceramic piezoelectric ultrasonic motors. Ultrasonic motors offer the advantage of low speed, high torque operation without the need for gears. They can be made compact and lightweight and provide a holding torque in the absence of applied power, due to the traveling wave frictional coupling mechanism between the rotor and the stator. This report covers modeling, simulation, fabrication and testing of ultrasonic motors. Design of experiments methods were also utilized to find optimal motor parameters. A suite of 8 mm diameter x 3 mm tall motors were machined for these studies and maximum stall torques as large as 10^(- 3) Nm, maximum no-load speeds of 1710 rpm and peak power outputs of 27 mW were realized. Aditionally, this report describes the implementation of a microfabricated ultrasonic motor using thin-film lead zirconate titanate. In a joint project with the Pennsylvania State University Materials Research Laboratory and MIT Lincoln Laboratory, 2 mm and 5 mm diameter stator structures were fabricated on 1 micron thick silicon nitride membranes. Small glass lenses placed down on top spun at 100-300 rpm with 4 V excitation at 90 kHz. The large power densities and stall torques of these piezoelectric ultrasonic motors offer tremendous promis for integrated machines: complete intelligent, electro-mechanical autonomous systems mass-produced in a single fabrication process.

An R Library for Compositional Data Analysis in Archaeometry

Compositional data naturally arises from the scientific analysis of the chemical composition of archaeological material such as ceramic and glass artefacts. Data of this type can be explored using a variety of techniques, from standard multivariate methods such as principal components analysis and cluster analysis, to methods based upon the use of log-ratios. The general aim is to identify groups of chemically similar artefacts that could potentially be used to answer questions of provenance. This paper will demonstrate work in progress on the development of a documented library of methods, implemented using the statistical package R, for the analysis of compositional data. R is an open source package that makes available very powerful statistical facilities at no cost. We aim to show how, with the aid of statistical software such as R, traditional exploratory multivariate analysis can easily be used alongside, or in combination with, specialist techniques of compositional data analysis. The library has been developed from a core of basic R functionality, together with purpose-written routines arising from our own research (for example that reported at CoDaWork'03). In addition, we have included other appropriate publicly available techniques and libraries that have been implemented in R by other authors. Available functions range from standard multivariate techniques through to various approaches to log-ratio analysis and zero replacement. We also discuss and demonstrate a small selection of relatively new techniques that have hitherto been little-used in archaeometric applications involving compositional data. The application of the library to the analysis of data arising in archaeometry will be demonstrated; results from different analyses will be compared; and the utility of the various methods discussed

Compositional data analysis in archaeometry

We shall call an n × p data matrix fully-compositional if the rows sum to a constant, and sub-compositional if the variables are a subset of a fully-compositional data set1. Such data occur widely in archaeometry, where it is common to determine the chemical composition of ceramic, glass, metal or other artefacts using techniques such as neutron activation analysis (NAA), inductively coupled plasma spectroscopy (ICPS), X-ray fluorescence analysis (XRF) etc. Interest often centres on whether there are distinct chemical groups within the data and whether, for example, these can be associated with different origins or manufacturing technologies

El Cas de l'arrendament de tota la terrissa de Quart

Descripció dels diferents privilegis que varen obtenir els ollers de Quart, des del Privilegi Reial, que els fou concedit pel rei Felip el 7 de maig de 1572

La tecnología del hidrógeno, una oportunidad estratégica para la perdurabilidad del sector energético en Colombia

El incremento de la actividad humana en el último siglo y el desarrollo de tecnologías ligadas con el petróleo como vector energético, han generado efectos medioambientales adversos que aunados con las limitadas reservas mundiales de crudo y su estrecha relación con el crecimiento económico mundial ha generado presiones economías, políticas y sociales en todos los países. Esta situación ha dinamizado la investigación y desarrollo de nuevas tecnologías basadas en el hidrogeno como un nuevo vector energético tecnológicamente compatible que permita la portabilidad de energía con el menor impacto ambiental y económico a la luz de la prospectiva de consumo y la perdurabilidad energética. Este trabajo identifica las experiencias más relevantes respecto a la tecnología del hidrogeno a nivel mundial con el fin de consolidar un plan estratégico para la incorporación del hidrógeno como vector energético al portafolio productivo colombiano mediante la aplicación de un modelo que permite el análisis del nivel de integración de los sectores educativo, empresarial y gubernamental, teniendo como base los resultados del análisis estructural y análisis de actores.

Prevalencia de dolor lumbar en los trabajadores de una planta de fabricación de productos de cerámica de Madrid, Cundinamarca, en el turno de 6 am a 2pm, año 2014.

Objetivo: Establecer la prevalencia, incapacidad y discapacidad de dolor lumbar en los trabajadores de la planta de fabricación de productos de cerámica, de Madrid Cundinamarca, del turno de 6 am a 2 pm año 2014. Metodología: Se realizó un estudio de corte transversal para determinar la prevalencia, incapacidad y discapacidad de dolor lumbar en un grupo de trabajadores que asisten en el turno de 6 am a 2 pm, en una empresa fabricante de productos de cerámica en el municipio de Madrid, departamento de Cundinamarca, Colombia. Se tuvieron en cuenta variables como edad, puesto de trabajo, antigüedad en cargo actual, consumo de cigarrillo, actividad física, presencia o ausencia de dolor lumbar e intensidad del dolor lumbar. Se aplicaron dos escalas para determinar el nivel de incapacidad y discapacidad para el dolor lumbar. Se empleó la escala de Owestry (ODI, OswestryDisabilityIndex) para evaluar la incapacidad de dolor lumbar y la escala de Roland-Morris para discapacidad física. Para le análisis de las variables continuas se determinó el supuesto de normalidad utilizando la prueba de ShapiroWilks.Para determinar la presencia de asociaciones se utilizó la prueba de Ji cuadrado de Pearson o el test exacto de Fischer si el valor esperado es menor a cinco. Para el análisis de la información se utilizó el software EpiInfo versión 7.1.3 (CDC, Atlanta, EE.UU.) Resultados: Se incluyeron 99 trabajadores, rango de edad entre 32 y 46 años y una mediana de 37 años. Más de la mitad de los trabajadores evaluados reportaron un dolor moderado (n=57), tan solo un 10% reportó máximo dolor, la escala de incapacidad de Oswestry78 trabajadores se ubicaron entre 0 y 40% reflejando esto ausencia de incapacidad, y solo 4 pacientes presentaron valores entre 40 y 60% incapacidad moderada. La escala de discapacidad de Roland-Morris mostró que la mayoría de los trabajadores presentan una discapacidad leve (n=97) y tan solo 2 trabajadores presentaron discapacidad moderada.La única asociación positiva encontrada se dio entre la presencia de dolor lumbar y la ejecución de actividad física una vez a la semana (p 0,005). Conclusiones: el dolor lumbar está presente en más del 50% de los trabajadores encuestados; sin embargo solo 4 de los trabajadores encuestados, presenta incapacidad por este dolor. En cuanto a la discapacidad pudimos determinar que solo 2 de los trabajadores la manifiesta.

Análisis de los componentes de la cadena de suministro y su relación con el desempeño superior de la organización en el sector manufacturero

En este documento se evidencia como el desempeño organizacional de una empresa, entendido como el rendimiento superior de la misma, se ve modificado por las prácticas o metodologías utilizadas, aplicadas e integradas a cada uno de los componentes de la Cadena de suministros. Es así que el propósito principal es demostrar cual es la relación entre los componentes de la Cadena de Suministros y su gestión sobre los rendimientos económicos de la empresa. De esa manera se encontraron múltiples actividades que toman lugar en los procesos característicos de cada uno de los componentes de la cadena de suministros y que al final nos presentan una variabilidad sobre los rendimientos de la empresa. Cabe recalcar que la investigación se realizó con respecto a empresas pertenecientes al sector manufacturero y abarca una buena parte de este. La importancia que tiene la investigación, es el haber entregado como resultado, el conocimiento sobre algunas de las practicas más utilizadas en el sector en cada uno de sus componentes, lo cual hace de la Cadena de suministros, un factor por excelencia para ser tratado e implementado con el fin de alcanzar mayores rendimientos económicos a nivel de empresa. En la investigación se utilizaron los casos de empresas reales tanto nacionales como internacionales y se encontraron situaciones claves que evidenciaban la hipótesis de la relación entre la cadena de suministros y el desempeño organizacional. Es por ello, que si bien es ahora cierto, que las actividades desarrolladas en los componentes de la Cadena de Suministros de las empresas influyen en el incremento de los rendimientos, es importante que las empresas conozcan de esta información para tener una idea de cómo desarrollar ventajas competitivas que los posicionen como empresa y les genere entonces mayores rendimientos, o por el contrario, les genere ahorros en costos y por ende altos beneficios y nuevas inversiones en prácticas que a la larga volverá a la empresa en un organismo eficientes y próspero.

Oscil.lacions del nivell del mar i sediments associats durant l'Holocè a la Costa Brava Meridional (Girona)

Several marine deposits in the southern Costa Brava shoreline have been studied. They appear at different heights above and below the present sea level. Three groups are defined in relation to their origin: conglomerate levels at the bottom of the cliffs, not-cemented emerged beaches and cemented submerged beaches. The age of the emerged beaches has been accurately determined by means of the ceramic content and radiocarbon dating. Chronological succession of the deposits and their stratigraphic and paleontological characteristics allow to define a sequence of the sea level changes during the latest stages of the versiliane transgression in the studied area