873 resultados para FAILURES
Resumo:
The failure of materials is always an unwelcome event for several reasons: human lives are put in danger, economic losses, and interference in the availability of products and services. Although the causes of failures and behaviour of materials can be known, the prevention of such a condition is difficult to be guaranteed. Among the failures, wear abrasion by the low voltage is the kind of failure that occurs in more equipment and parts industry. The Plants Sucroalcooleiras suffer significant losses because of such attrition, this fact that motivated their choice for the development of this work. For both, were considered failures in the swing hammers desfibradores stopped soon after the exchange provided in accordance with tonnage of cane processed, then were analyzed by the level of wear testing of rubber wheel defined by the standard ASTM G65-91.The failures were classified as to the origin of the cause and mechanism, moreover, were prepared with samples of welding procedures according to ASME code, sec. IX as well, using the technique of thermal spraying to analyze the performance of these materials produced in laboratories, and compares them with the solder used in the plant. It was observed that the bodies-of-proof prepared by the procedure described as welding, and the thermal spraying the results of losing weight have been minimized significantly compared to the preparations in the plant. This is because the use of techniques more appropriate and more controlled conditions of the parameters of welding. As for the thermal spraying, this technique has presented a satisfactory result, but requires the use of these coatings in the best condition for real affirmation of the results
Resumo:
Several problems related to the loss of hydraulic seal in oilwells, causing gas migration and/or contamination of the production zone by water, have been reported. The loss of the hydraulic seal is a consequence of cracks which can be occasioned either by the invasion of gas during the wait on cement or by the expansion of the casing causing the fracture of the cement sheath. In case of the pressure of the formation is higher than the pressure in the annulus, gas can migrate into the slurry and form microannulus, which are channels where gas migrates after the cement is set. Cracks can be also occasioned by the fracture of the cement sheath when it does not withstand the thermal and dynamic loads. In reservoirs where the oil is heavy, steam water injection operation is required in order to get the oil flowing. This operation increases the temperature of the casing, and then it expands and causes the fracture of the cement sheath in the annulus. When the failures on the cement are detected, remedial cementing is required, which raise costs caused by the interventions. Once the use of cement in the construction civil sector is older than its use in the petroleum sector, it is common to bring technologies and solutions from the civil construction and apply them on the petroleum area. In this context, vermiculite, a mineral-clay widely encountered in Brazil, has been used, on its exfoliated form, in the civil construction, especially on the manufacture of lights and fireproof concretes with excellent thermal and acoustical properties. It has already been reported in scientific journals, studies of the addition of exfoliated vermiculite in Portland cements revealing good properties related to oilwell cementing operations. Thus, this study aimed to study the rheological behavior, thickening time, stability and compressive strength of the slurries made of Portland cement and exfoliated vermiculite in 5 different compositions, at room temperature and heated. The results showed that the compressive strength decreased with the addition of exfoliated vermiculite, however the values are still allowed for oiwell cementing operations. The thickening time of the slurry with no exfoliated vermiculite was 120 min and the thickening time of the slurry with 12 % of exfoliated vermiculite was 98 min. The stability and the rheological behavior of the slurries revealed that the exfoliated vermiculite absorbed water and therefore increased the viscosity of the slurries, even though increasing the factor cement-water. The stability experiment carried out at 133 ºF showed that, there was neither sedimentation nor reduction of the volume of the cement for the slurry with 12 % of exfoliated vermiculite. Thus, the addition of exfoliated vermiculite accelerates the set time of the cement and gives it a small shrinkage during the wait on cement, which are important to prevent gas migration
Resumo:
Oil wells subjected to cyclic steam injection present important challenges for the development of well cementing systems, mainly due to tensile stresses caused by thermal gradients during its useful life. Cement sheath failures in wells using conventional high compressive strength systems lead to the use of cement systems that are more flexible and/or ductile, with emphasis on Portland cement systems with latex addition. Recent research efforts have presented geopolymeric systems as alternatives. These cementing systems are based on alkaline activation of amorphous aluminosilicates such as metakaolin or fly ash and display advantageous properties such as high compressive strength, fast setting and thermal stability. Basic geopolymeric formulations can be found in the literature, which meet basic oil industry specifications such as rheology, compressive strength and thickening time. In this work, new geopolymeric formulations were developed, based on metakaolin, potassium silicate, potassium hydroxide, silica fume and mineral fiber, using the state of the art in chemical composition, mixture modeling and additivation to optimize the most relevant properties for oil well cementing. Starting from molar ratios considered ideal in the literature (SiO2/Al2O3 = 3.8 e K2O/Al2O3 = 1.0), a study of dry mixtures was performed,based on the compressive packing model, resulting in an optimal volume of 6% for the added solid material. This material (silica fume and mineral fiber) works both as an additional silica source (in the case of silica fume) and as mechanical reinforcement, especially in the case of mineral fiber, which incremented the tensile strength. The first triaxial mechanical study of this class of materials was performed. For comparison, a mechanical study of conventional latex-based cementing systems was also carried out. Regardless of differences in the failure mode (brittle for geopolymers, ductile for latex-based systems), the superior uniaxial compressive strength (37 MPa for the geopolymeric slurry P5 versus 18 MPa for the conventional slurry P2), similar triaxial behavior (friction angle 21° for P5 and P2) and lower stifness (in the elastic region 5.1 GPa for P5 versus 6.8 GPa for P2) of the geopolymeric systems allowed them to withstand a similar amount of mechanical energy (155 kJ/m3 for P5 versus 208 kJ/m3 for P2), noting that geopolymers work in the elastic regime, without the microcracking present in the case of latex-based systems. Therefore, the geopolymers studied on this work must be designed for application in the elastic region to avoid brittle failure. Finally, the tensile strength of geopolymers is originally poor (1.3 MPa for the geopolymeric slurry P3) due to its brittle structure. However, after additivation with mineral fiber, the tensile strength became equivalent to that of latex-based systems (2.3 MPa for P5 and 2.1 MPa for P2). The technical viability of conventional and proposed formulations was evaluated for the whole well life, including stresses due to cyclic steam injection. This analysis was performed using finite element-based simulation software. It was verified that conventional slurries are viable up to 204ºF (400ºC) and geopolymeric slurries are viable above 500ºF (260ºC)
Resumo:
Metal-ceramic interfaces are present in tricone drill bits with hard ceramic inserts for oil well drilling operations. The combination of actions of cutting, crushing and breaking up of rocks results in the degradation of tricone drill bits by wear, total or partial rupture of the drill bit body or the ceramic inserts, thermal shock and corrosion. Also the improper pressfitting of the ceramic inserts on the bit body may cause its total detachment, and promote serious damages to the drill bit. The improvement on the production process of metal-ceramic interfaces can eliminate or minimize some of above-mentioned failures presented in tricone drill bits, optimizing their lifetime and so reducing drilling metric cost. Brazing is a widely established technique to join metal-ceramic materials, and may be an excellent alternative to the common mechanical press fitting process of hard ceramic inserts on the steel bit body for tricone drill bit. Wetting phenomena plays an essential role in the production of metal/ceramic interfaces when a liquid phase is present in the process. In this work, 72Silver-28Copper eutectic based brazing alloys were melted onto zirconia, silicon nitride and tungsten carbide/Co substrates under high vacuum. Contact angle evolution was measured and graphically plotted, and the interfaces produced were analysed by SEM-EDX. The AgCu eutectic alloy did not wet any ceramic substrates, showing high contact angles, and so without chemical interaction between the materials. Better results were found for the systemns containing 3%wt of titanium in the AgCu alloy. The presence os titanium as a solute in the alloy produces wettable cand termodinamically stable compounds, increasing the ceramics wetting beahviour
Resumo:
Steam injection is the most used thermal recovery method of oil nowadays because of the high degree of development of the technique that allows high recovery factors. However, injection of superheated steam into the reservoir affects the entire structure of the well, including the cemented layer that presents a retrogression of compressive strength and increases the permeability due to formation of more crystalline and denser phases at temperatures above 110 °C. These changes result in failures in the cement that favor the entrance of formation fluids into the annulus space resulting in unsafe operations and restrictions in the economic life of the well. But the strength retrogression can be prevented by partial replacement of cement by silica-based materials that reduce the CaO/SiO2 ratio of cement slurries changing the trajectory of the reactions, converting those deleterious phases in phases with satisfactory mechanical strength and permeability. The aim of this study was to evaluate the behavior of a ceramic waste material rich in silica in partial and total substitution of a mineral additive used to fight the strength retrogression of cement slurries subjected to high temperatures. The evaluation was made by compression, X-ray diffraction (XRD) and thermogravimetry (TG/DTG). The samples were submitted to a cycle of low temperature (38 °C) for 28 days and a cycle of low temperature followed by exposure to 280 ºC and 1000 psi by 3 days. The results showed that slurries with additions of up to 30% of the waste material are not enough to prevent the strength retrogression, while slurries with additions of the waste material combined with silica flour in various proportions produced hydrated products of low Ca/Si ratios that maintained the compressive strength at satisfactory levels
Resumo:
The Electrical Submersible Pumping is an artificial lift method for oil wells employed in onshore and offshore areas. The economic revenue of the petroleum production in a well depends on the oil flow and the availability of lifting equipment. The fewer the failures, the lower the revenue shortfall and costs to repair it. The frequency with which failures occur depends on the operating conditions to which the pumps are submitted. In high-productivity offshore wells monitoring is done by operators with engineering support 24h/day, which is not economically viable for the land areas. In this context, the automation of onshore wells has clear economic advantages. This work proposes a system capable of automatically control the operation of electrical submersible pumps, installed in oil wells, by an adjustment at the electric motor rotation based on signals provided by sensors installed on the surface and subsurface, keeping the pump operating within the recommended range, closest to the well s potential. Techniques are developed to estimate unmeasured variables, enabling the automation of wells that do not have all the required sensors. The automatic adjustment, according to an algorithm that runs on a programmable logic controller maintains the flow and submergence within acceptable parameters avoiding undesirable operating conditions, as the gas interference and high engine temperature, without need to resort to stopping the engine, which would reduce the its useful life. The control strategy described, based on modeling of physical phenomena and operational experience reported in literature, is materialized in terms of a fuzzy controller based on rules, and all generated information can be accompanied by a supervisory system
Resumo:
Rio Grande do Norte is among the Brazilian States where the tourism and sexual violence increasingly grow in the country, occupying 4th place in 2004. Associated to this fact, it comes the problematic one of the contamination of the women by Sexually Transmitted Disease (STD). Studies in Brazil have presented a considerable increase of the STDs, caused through lack of suitable protection in the sexual relationships. Due to the biological and psychosocial vulnerability, besides failures or inconsistencies in the condom use associated to the raised taxes of sexual activity with different partners, the STDs constitute the main risk of health. Many difficulties are found by the confrontation of this problem. In this context, this project had as aim to evaluate the vulnerability of this population of sexually active women in Natal-RN Ponta Negra neighbourhood to the infections by STDs, such as, Candida sp., Vaginoses Bacterial, Trichomonas Vaginalis and Chlamydia sp., arisen with the explosion of the sex market, showing a current statistical panorama. It was possible to detect vulnerable points in prevention through patient anamnesis, where the study it showed: high number of partners (8,3% with more than five), low age of first relationship and not the use of condoms (31,8% sometimes use and 45,8% had not used in the first relationship). Already consolidated by the preventive cytopathologic examination, these data were strengthened by high incidence of causing agents of STDs (58,6%). In this way, it is clear that the sexuality must to be thought on the context of the deep economic and socio-cultural transformations in which pass societies, and mainly the ones concerning to the sexuality exercise and to the sex market. With the profile change of the infections, new demands are placed in relation to the risk factors. Therefore, it can be concluded that the prevention vulnerable points detected as more important had been the deficiency in self-perception and wareness of the risk existence among the studied women
Resumo:
We study the health care focused on care in an intercessor and dialogical relationship with the User, which involves the construction of therapeutic projects essential to the quality of the treatment of the user in health services, and it is necessary individual and collective actions. It is intended to acknowledge and analyze the perception of social subjects, users and professionals on the treatment given to a user of a Specialized Outpatient Service (Serviço Ambulatorial Especializado SAE) in STD/HIV/AIDS state reference in Natal, RN. The study is structured in a transdisciplinary vision of science and knowledge, theoretical and methodological principles that give meaning to the expression of the institutional features of care and health care reconnecting them to the social context. As a research strategy we seek the expressions of 56 subjects of social research, which agreed to participate in the sample, from a symbolic map of the attention, coupled with the techniques of observation and semi-structured interview. For the analysis of the results, five categories of analysis were established: the meaning of the service, care perception, process of communication and interaction, treatment perception and organization and evaluation of the service. It is argued that the attention and care are developed in a technical health care assistance to the disease, focusing on attention based on treatment, on diagnostic and drug therapy of antiretroviral drugs, reflecting the traditional biomedical paradigm of attention to the disease. This is also the mode of organization of practical actions in daily SAE: the therapy proves to be fragmented in several specialties, vertical and feeds the same model, generating tension and overload for professionals; showing impersonal care focused on structured and informative technology, unrelated to an interactive dialogic. From the speech of the subjects, the SAE is understood as the place of confrontation with the disease, but also enables greater elaboration of the illness by meeting their peers. Living with HIV and AIDS is living with concern, apprehension and fear, but mainly with the stigma, prejudice and exclusion, which require that the disease is kept in secret. There is a movement of forces and power, expressed in the knowledge-power of those who dominate the technical and administrative capabilities, devices that concentrate the maintenance of the medicalization of care, rapid consultations and with little attention, making it difficult to interact with and listen to, combined with structural failures, organizational and inadequate management of the service. We conclude that there are dimensions that are not considered in the internal dynamics of the care service multiple forms, characterized by care conflicting models, marked by individual interventions related to the disease. The subject is not considered together with his speech as technical discourse is imposed and care production based on material technology is observed
Resumo:
This thesis is defined as a reflection on the mechanisms of expression and insertion of the homo situs in the participatory governance in Mozambique. For a better understanding of this social fact, it was settled a periodization which covered the decline of colonialism at the time of the independence, which was proclaimed in June 1975, the civil war that lasted over 16 years and the period of the democratic State, further established. Therefore, we sought to understand the mechanisms and failures of the participation of the homo situs in local development projects that absorbed the needs and problems of these peasants, not mobilizing the skills and social competences of these communities. It would be essential for the homo situs a genuine democratic practice involving a political culture based on the social construction of the territories of the traditional man which was characterized by being procedural and historical, finding in participation its higher base. In this context, it would be desirable that the community development in Mozambique could contemplate and respect the choices of the homo situs. For this purpose, it would be fundamental the consistency between theory and practice, which builds and rebuilds, continually the competence of the peasants, facilitating the possibility of realization of their primordial aspirations. In the research, it became apparent that there is not a continuous process of participation of the rural communities, which appear as participants, only at the time of the implementation of the activities. Therefore, even having the participation of the communities expected by the law, with predictable moments of discussion and necessary conditions for that, the State failed to establish an ongoing process of democratic dialogue with traditional populations, as well as it failed to organize, properly, accurate informational bases to help solve the problems of rural areas. These facts have led to obstacles to the process of conquest of the human and civil rights of the traditional communities
Resumo:
In the Brazilian legal scenario, the study of taxation has traditionally been restricted to positivist analysis, concerned with investigating the formal aspects of the tax legal rule. Despite its relevance to the formation of the national doctrine of tax, such formalist tradition limits the discipline, separating it from reality and the socioeconomic context in which the Tax Law is inserted. Thus, the proposal of the dissertation is to examine the fundamentals and nature of taxation and tax legal rules from the perspective of Law and Economics (Economic Analysis of Law). For this purpose, the work initially reconnects the Tax Law and Science of Finance (or Public Finance) and Fiscal Policy, undertaking not only a legal analysis, but also economic and financial analysis of the theme. The Economics of Public Sector (or Modern Public Finance) will contribute to the research through topics such as market failures and economic theory of taxation, which are essential to an economic approach to Tax Law. The core of the work lies in the application of Law and Economics instruments in the study of taxation, analyzing the effects of tax rules on the economic system. Accordingly, the dissertation examines the fundamental assumptions that make up the Economic Analysis of Law (as the concept of economic efficiency and its relation to equity), relating them to the tax phenomenon. Due to the nature of the Brazilian legal system, any worth investigation or approach, including Law and Economics, could not pass off the Constitution. Thus, the constitutional rules will serve as a limit and a prerequisite for the application of Law and Economics on taxation, particularly the rules related to property rights, freedom, equality and legal certainty. The relationship between taxation and market failures receives prominent role, particularly due to its importance to the Law and Economics, as well as to the role that taxation plays in the correction of these failures. In addition to performing a review of taxation under the approach of Economic Analysis of Law, the research also investigates the reality of Brazilian tax system, applying the concepts developed in relevant cases and issues to the national scene, such as the relationship between taxation and development, the compliance costs of taxation, the tax evasion and the tax enforcement procedure. Given the above, it is intended to lay the groundwork for a general theory of Economic Analysis of Tax Law, contextualizing it with the Brazilian tax system
Resumo:
The existence of inequalities among the Brazilian regions is an indeed fact along the country s history. Before this reality the constitutional legislator inserted into the Federal Constitution of 1988, as a purpose of the Federative Republic of Brazil, the reduction of regional inequalities. The development has also been included as a purpose from the State, because there is an straight relation with the reduction of regional inequalities. In both situations is searched the improvement of people s living conditions. . In pursuit of this achievement, the State must implement public policy, and, for this to happen, it needs the ingress of income inside of the public coffers and support of economic agents, therefore the importance of constitucionalization of the economic policy. The 1988 s Constitution adopted a rational capitalism regime consentaneous with current legal and social conceptions, that s why it enabled the State s intervention into economy to correct the so-called market failures or to make the established objectives fulfilled. About this last one, the intervention may happen by induction through the adoption of regulatory Standards of incentive or disincentive of economic activity. Among the possible inductive ways there are the tax assessments that aim to stimulate the economic agents behavior in view of finding that the development doesn t occur with the same intensity in all of the country s regions. Inside this context there are the Export Processing Zones (EPZs) which are special areas with different customs regime by the granting of benefits to the companies that are installed there. The EPZs have been used, by several countries, in order to develop certain regions, and economic indicators show that they promoted economic and social changes in the places where they are installed, especially because, by attracting companies, they provide job creation, industrialization and increased exports. In Brazil, they can contribute decisively to overcome major obstacles or decrease the attraction of economic agents and economic development of the country. In the case of an instrument known to be effective to achieve the goals established by the Constitution, it is duty of the Executive to push for the law that governs this customs regime is effectively applied. If the Executive doesn t fulfill this duty, incurs into unjustifiable omission, correction likely by the Judiciary, whose mission is to prevent acts or omissions contrary to constitutional order
Resumo:
For young people and adults that have not yet conquered reading and writing, being literate is the most important thing in life , a dream . Scholarly learning for them is like hegemonic knowledge in contemporary literate society. Thus, for them to get into school is to be able to have such knowledge and, through it, feel inserted into this society. However, along this process of learning, they start to drop out, little by little, statistically increasing the number of people who give up on young people and adult education Eja, as well as slowly reducing the contingent of illiteracy in the country. With this reality as a starting point, we question the concrete and symbolic reasons or motives that lead to a dropping out of the literacy classes at Eja. To do so, we have established, as the object of our study, the feelings of giving up among those involved in young people and adult literacy training. To understand such feelings is our purpose in this investigation. The theory of Social Representations (MOSCOVICI, 1978, 2004) was the theoretical-methodological option for subsidizing data search, analyses and interpretation, making us perceive the significance of the object of this study for these individuals. The gathering of such symbolic content involved the use of semi-structured interviews with eleven drop-outs and ten students who had repeated this modality of teaching in public schools in Natal, RN, during the 2006 school year. From the thematic and categorical analyses (BARDIN, 1977), we identified elements that gave support to some themes. Later, these themes led to three categories, suggesting that feelings associated with dropping out were based on the following: learning difficulties because they did not understand the contents; having their lack of knowledge exposed, thus bringing forth feelings of shame, humiliation, and embarrassment for not knowing how to read and write at a mature age; work, tiredness and sickness. The students who manage to remain in school are those who force themselves to live with the feelings of maladaptation and those who develop a sense of adaptation the other way round to the institution, that is, acceptance of institutional failures and omissions
Resumo:
This master´s thesis presents a reliability study conducted among onshore oil fields in the Potiguar Basin (RN/CE) of Petrobras company, Brazil. The main study objective was to build a regression model to predict the risk of failures that impede production wells to function properly using the information of explanatory variables related to wells such as the elevation method, the amount of water produced in the well (BSW), the ratio gas-oil (RGO), the depth of the production bomb, the operational unit of the oil field, among others. The study was based on a retrospective sample of 603 oil columns from all that were functioning between 2000 and 2006. Statistical hypothesis tests under a Weibull regression model fitted to the failure data allowed the selection of some significant predictors in the set considered to explain the first failure time in the wells
Resumo:
This work searches to offer a model to improve spare parts stock management for companies of urban passenger transport by bus, with the consequent progress in their maintenance management. Also known as MRO items (Maintenance, Repair and Operations), these spare parts, according their consumption and demand features, cost, criticity to operation, lead-time, quantity of suppliers, among other parameters, shouldn´t have managed their inventory like normal production items (work in process e final products), that because their features, are managed by more predictable models based, for example, in economic order quantity. In the case specifically of companies of urban passenger transport by bus, items MRO have significant importance in their assets and a bad management of these inventories can cause serious losses to company, leading it even bankrupticy business, in more severe situations which missing spare part provokes vehicles shutdown indefinitely. Given slight attention to the issue, which translates in little literature available about it when compared to that literature about normal items stocks, and due the fact that MRO items be critical to bus urban transport of passengers companies´, it is necessary, so, deepen in this theme searching to give technical and scientific subsidies to companies that work, in many times, empirically, with these so decisive inputs to their business. As a typical portfolio problem, in which there are n items, separated into critical and noncritical, while competing for the same resource, it was developed a new algorithm to aid in a better inventory management of spare parts used only in corrective maintenance (whose failures are unpredictable and random), by analyzing the cost-benefit ratio, which compares the level of service versus cost of each item. The model was tested in a company of urban passenger transport by bus from the city of Natal, who anonymously provided their real data to application in this work
Resumo:
The research aimed identify how the quality of services provided by Casa de Apoio à Criança com Câncer Durval Paiva is perceived by its users, giving an opportunity of improve their performance in social services provision pointing out the failures experienced, the institution will have the user as a important partner in fails identification, serving as a subsidy to the actions of correction and improvement to such situations demands. With this work implementation will be observed contributions that will permeate to the fields of theory and practice, enabling progress and enrichment on the subject. The theoretical contribution is observed as this work execution will provide greater advance about the models developed for the third sector. The proposed work will raise awareness issues about the full potential of the social economy, with regard to the quality of services provided by organizations, allowing a better definition of priorities on their development. The study addressed three issues: identifying the people that receive support of the Casa Durval Paiva, identifying what is the level of satisfaction of families served and evaluate the services provided by Casa Durval Paiva that demand improvements in the perception of families assisted. Found a demand for services has been found that the institution has a multidisciplinary team with a high level of professionalism, and supervised with students of various educational institutions and many volunteers to complement the actions of individual professionals. Was measured a high satisfaction of users of the services provided by Casa Durval Paiva