Political conditions for fair elections

Democracy is not necessarily consolidated simply by the introduction of formal democratic institutions. It is often observed in new democracies that democratic institutions are neglected and eroded in actual practice. Particularly, electoral fraud committed by a ruler is one of the main problems in this regard. This paper deals with two questions, (1) under what conditions does a ruler have an incentive to hold fair elections (or to rig elections), and (2) what makes a ruler prefer to establish an independent election governing institution? Assuming that a ruler prefers to maintain her power, basically she has an incentive to rig elections in order to be victorious in the political competition. A ruler, however, faces the risk of losing power if the opposition stages successful protests on a sufficiently large scale. If opponents are able to pose a credible threat to a ruler, she will have an incentive to hold fair elections. The problem is that information on electoral fraud is not shared by every player in the game. For the opposition, imperfect information deepens their coordination problems. Imperfect information, on the other hand, in some cases causes a problem for a ruler. If the opposition is sufficiently cohesive and have little tolerance of cheating, even unverified suspicions of fraud may trigger menacing protests. In such a case, a ruler has an incentive to establish an independent election commission to avoid unnecessary collisions by revealing the nature of the elections.

Study of the Mechanical Strength Improvement of Wafers for EWT Solar Cells by Chemical Etching after the Drilling Process

Mechanical stability of EWT solar cells deteriorates when holes are created in the wafer. Nevertheless, the chemical etching after the hole generation process improves the mechanical strength by removing part of the damage produced in the drilling process. Several sets of wafers with alkaline baths of different duration have been prepared. The mechanical strength has been measured by the ring on ring bending test and the failure stresses have been obtained through a FE simulation of the test. This paper shows the comparison of these groups of wafers in order to obtain an optimum value of the decreased thickness produced by the chemical etching

Accelerated life test of high luminosity AlGaInP LEDs

Specific tests to assess reliability of high luminosity AlInGaP LED for outdoor applications are needed. In this paper tests to propose a model involving three parameters: temperature, humidity and current have been carried out. Temperature, humidity and current accelerated model has been proposed to evaluate the reliability of this type of LED. Degradation and catastrophic failure mechanisms have been analyzed. Finally we analyze the effect of serial resistance in power luminosity degradation.

Preliminary temperature Accelerated Life Test (ALT) on III-V commercial concentrator triple-junction solar cells

A quantitative temperature accelerated life test on sixty GaInP/GaInAs/Ge triple-junction commercial concentrator solar cells is being carried out. The final objective of this experiment is to evaluate the reliability, warranty period, and failure mechanism of high concentration solar cells in a moderate period of time. The acceleration of the degradation is realized by subjecting the solar cells at temperatures markedly higher than the nominal working temperature under a concentrator Three experiments at three different temperatures are necessary in order to obtain the acceleration factor which relates the time at the stress level with the time at nominal working conditions. . However, up to now only the test at the highest temperature has finished. Therefore, we can not provide complete reliability information but we have analyzed the life data and the failure mode of the solar cells inside the climatic chamber at the highest temperature. The failures have been all of them catastrophic. In fact, the solar cells have turned into short circuits. We have fitted the failure distribution to a two parameters Weibull function. The failures are wear-out type. We have observed that the busbar and the surrounding fingers are completely deteriorate

Study about the Problem of Dropping of Subjects by Students During an Academinc Year at the University.

In university studies, it is not unusual for students to drop some of the subjects they have enrolled in for the academic year. They start by not attending lectures, sometimes due to neglect or carelessness, or because they find the subject too difficult, this means that they lose the continuity in the topics that the professor follows. If they try to attend again they discover that they hardly understand anything and become discouraged and so decide to give up attending lectures and study on their own. However some fail to turn up to do their final exams and the failure rate of those who actually do the exams is high. The problem is that this is not only the case with one specific subject, but it is often the same with many subjects. The result is that students arent’s productive enough, wasting time and also prolonging their years of study which entails a great cost for families. Degree courses structured to be conducted and completed in three academic courses, it may in fact take up to an average of six or more academic courses. In this paper, we have studied this problem, which apart from the waste of money and time, produces frustration in the student, who finds that he has not been able to achieve what he had proposed at the beginning of the course. It is quite common, to find students who do not even pass nor 50% of the subjects they had enrolled in for the academic year. If this happens repeatedly to a student, it can be the point when he considers dropping out altogether. This is also a concern for the universities, especially in the early courses. In our experience as professors, we have found that students, who attend lectures regularly and follow the explanations, approach the final exams with confidence and rarely fail the subject. In this proposal we present some techniques and methods carried out to solve in possible, the problem of lack of attendance to lectures. This involves "rewarding students for their assistance and participation in lectures". Rewarding assistance with a "prize" that counts for the final mark on the subject and involving more participation in the development of lectures. We believe that we have to teach students to use the lectures as part of their learning in a non-passive way. We consider the professor's work as fundamental in terms of how to convey the usefulness of these topics explained and the applications that they will have for their professional life in the future. In this way the student see for himself the use and importance of what he is learning. When his participation is required, he will feel more involved and confident participating in the educational system. Finally we present statistical results of studies carried out on different degrees and on different subjects over two consecutive years. In the first year we assessed only the final exams without considering the students attendance, or participation. In the second year, we have applied the techniques and methods proposed here. In addition we have compared the two ways of assessing subjects.

Risk-based methodology for parameter calibration of a reservoir flood control model

Flash floods are of major relevance in natural disaster management in the Mediterranean region. In many cases, the damaging effects of flash floods can be mitigated by adequate management of flood control reservoirs. This requires the development of suitable models for optimal operation of reservoirs. A probabilistic methodology for calibrating the parameters of a reservoir flood control model (RFCM) that takes into account the stochastic variability of flood events is presented. This study addresses the crucial problem of operating reservoirs during flood events, considering downstream river damages and dam failure risk as conflicting operation criteria. These two criteria are aggregated into a single objective of total expected damages from both the maximum released flows and stored volumes (overall risk index). For each selected parameter set the RFCM is run under a wide range of hydrologic loads (determined through Monte Carlo simulation). The optimal parameter set is obtained through the overall risk index (balanced solution) and then compared with other solutions of the Pareto front. The proposed methodology is implemented at three different reservoirs in the southeast of Spain. The results obtained show that the balanced solution offers a good compromise between the two main objectives of reservoir flood control management

Comportamiento a fatiga por cortante de elementos lineales de hormigón armado sin cercos

Las estructuras de hormigón son susceptibles de sufrir los efectos asociados a las acciones de fatiga cuando estas se ven sometidas a un elevado número de cargas repetidas. Muchas de estas estructuras no requieren armadura transversal para cumplir los condicionantes de dimensionamiento estático como por ejemplo las losas superiores de tableros de puentes, los muros de contención, las losas de transición de puentes, las torres eólicas o las estructuras marítimas. La mayor parte de los códigos de diseño vigentes no incluyen una comprobación específica del nivel de seguridad a cortante de estas estructuras para acciones de fatiga, y aquellas que lo hacen prefieren utilizar expresiones de tipo empírico basadas en curvas S-N que relacionan el número de ciclos resistentes con el valor de la carga aplicada. A pesar de que el empleo de curvas S-N es de gran utilidad desde un punto de vista práctico, estas curvas no permiten comprender el proceso de rotura por cortante para cargas repetidas. El objetivo principal de esta Tesis es el de estudiar el comportamiento a cortante de elementos de hormigón armado sin cercos sometidos a fatiga. Además, el análisis es ampliado al estudio del comportamiento transversal de los voladizos de las losas superiores de tableros de puentes de hormigón que de forma habitual son diseñados sin armadura de cortante. De forma habitual estos elementos se diseñan atendiendo a criterios de dimensionamiento estáticos sin tener en cuenta la resistencia a cortante cuando se ven sometidos a cargas cíclicas. A pesar de que las cargas de fatiga son inferiores a aquellas que producen el fallo estático, es importante tener en cuenta el comportamiento de estos elementos ante cargas repetidas. Los trabajos experimentales existentes en vigas de hormigón armado sin cercos evidenciaron diferencias significativas entre los modos de fallo ante cargas estáticas y cíclicas. Estos trabajos llegaron a la conclusión de que estos elementos diseñados para tener un fallo dúctil por flexión pueden llegar a desarrollar un tipo de fallo frágil por cortante cuando se ven sometidos a cargas repetidas. El proceso de rotura por cortante en elementos de hormigón armado sin cercos sometidos a fatiga es un proceso complejo que debe ser estudiado en profundidad debido al carácter frágil de este tipo de fallo. Los trabajos experimentales permitieron comprobar que el origen de este fallo tiene lugar tras la formación de una fisura de cortante a partir de una fisura de flexión formada durante los primeros ciclos en el vano de cortante. Tras la formación de esta fisura, esta se va propagando hacia la cabeza de compresión hasta que finalmente se produce el fallo como consecuencia de la destrucción de la cabeza de compresión cuando la altura alcanzada por esta es insuficiente para resistir la fuerza de compresión aplicada en esta zona. Por otra parte, la propagación de esta fisura diagonal puede desarrollarse por completo en el instante en el que esta se forma derivando en un tipo de fallo por cortante más frágil que el anterior. El proceso de fatiga es estudiado en esta Tesis mediante un modelo mecánico. Por una parte, se propone un modelo predictivo para determinar el número de ciclos acumulados hasta que se forma la fisura diagonal en función del estado tensional que se tiene en la punta de una fisura crítica de flexión formada en los primeros ciclos. Por otra parte, la resistencia a fatiga tras la formación de la fisura diagonal se analiza teniendo en cuenta el daño por fatiga acumulado en la cabeza de compresión y las variables que afectan a la propagación de esta fisura de cortante. Para la evaluación de la resistencia a fatiga tras la formación de la fisura crítica de cortante en este tipo de elementos, se plantea un modelo teórico basado en conceptos de Mecánica de la Fractura adaptados al hormigón. Este modelo puede ser aplicado a vigas de hormigón armado sin cercos de canto constante o variable siguiendo diferentes procedimientos. Una campaña experimental ha sido llevada a cabo con el objetivo de estudiar el comportamiento a cortante de vigas de hormigón armado sin cercos de canto variable sometidas a cargas estáticas y de fatiga. Se han desarrollado un total de diez ensayos estáticos y de fatiga para diferentes niveles de carga y esbelteces de cortante, teniendo lugar diferentes modos de fallo. Estos elementos fueron diseñados para reproducir, a escala real y de forma simplificada, los voladizos laterales de las losas superiores de tableros de puentes de carretera de hormigón. Los resultados experimentales demostraron que el tipo de fallo desarrollado depende de varios parámetros como por ejemplo el nivel de carga máxima, el nivel de oscilación de tensiones en la armadura longitudinal, la esbeltez de cortante o la calidad del hormigón utilizado entre otros. Para valores similares de esbeltez de cortante, los ensayos de fatiga realizados permitieron comprobar que la rotura por cortante de estos elementos está asociada a niveles de carga máxima elevados, mientras que el fallo por fatiga de la armadura longitudinal tiene mayor probabilidad de ocurrir en elementos sometidos a elevados niveles de oscilación de tensiones en esta armadura. Además, estos ensayos han sido analizados a través del modelo propuesto para tratar de comprender el comportamiento resistente de estos elementos sometidos a cargas de fatiga. Concrete structures are able to suffer fatigue when they are subjected to high number of cyclic loads. Many of these need not shear reinforcement to satisfy static design requirements, such as bridge deck slabs, retaining walls, bridge approach slabs, wind towers or maritime structures among others. Many codes of practice do not include a verification of the shear fatigue safety. Moreover, those which include it still prefer empirical S-N-based approaches that provide the number of cycles as a function of applied forces. S-N models are practical but they do not provide information to understand the shear fatigue process. The main objective of this Thesis is to study shear behaviour of reinforced concrete elements without stirrups subjected to fatigue loads. In addition, the analysis is extended in order to study the transverse behaviour of cantilever slabs of concrete bridges that traditionally are designed without shear reinforcement. These elements usually are designed on the basis of static strength and it is unusual that codes consider fatigue strength of concrete in shear. Accordingly, it is important to take into account the fatigue behaviour of structural members subjected to cyclic loads although these loads are lower than those which produce the static failure. Existing experimental works show important differences between the static and cyclic failure modes of reinforced concrete beams without stirrups. These works concluded that beams without transverse reinforcement, designed to have a ductile failure mode in flexure, can submit a brittle shear failure mode when they are subjected to repeated loads. Shear fatigue failure of reinforced concrete beams without stirrups is a rather complex process from the mechanical viewpoint. Since it leads to a brittle failure mode it should be better understood. Experimental evidence indicates that a diagonal crack first develops from the inclination of flexural cracks in the shear span. Thereafter, the diagonal crack propagates into the compression zone. Failure normally takes place by the destruction of the compression zone when its depth is too small to resist the applied force. The propagation of the diagonal crack can also be instantaneous, leading to sudden diagonal cracking fatigue failure rather than shear-compression failure. Fatigue process is studied in this Thesis on a mechanical basis. On the one hand, a predictive model is derived to obtain the number of cycles up to diagonal cracking, as a function of the stress state at the tip of a critical flexural crack. On the other hand, the residual fatigue strength after diagonal cracking is analyzed taking into account the fatigue damage accumulated by the compression zone and the variables affecting the propagation of the diagonal crack. In order to assess the residual fatigue strength after diagonal cracking of such elements, a theoretical model is proposed based on concepts from fracture mechanics adapted to concrete. This model can be successfully applied for straight or haunched reinforced concrete beams without stirrups following different procedures. In order to achieve a more advanced knowledge in this subject, an experimental campaign has been carried out with the aim of study the shear behaviour of reinforced concrete haunched beams without stirrups subjected to static and fatigue loads. A total of ten static and fatigue tests have been performed with distinct load levels and shear span-to-depth ratios, presenting different failures modes. These elements were designed to reproduce in a simplified form the cantilever slab of concrete bridges at real scale. Experimental results showed that the type of failure depends on several parameters as for example the maximum load level, the stress oscillation level on the longitudinal reinforcement, the shear span-to-depth ratio or the quality of the concrete used among others. For a similar value of the shear span-to-depth ratio, tests evidenced that shear fatigue failure is related to high maximum load levels, while steel fatigue failure is easier to occur in elements subjected to high stress oscillation level on the reinforcement bars. Besides, these tests have been analyzed through the proposed model in order to clarify the structural behaviour of such elements subjected to fatigue loads.

Aplicación de la regresión logística en la predicción empírica de fenómenos complejos en obras subterráneas : squeezing y rotura de pilares de carbón

La heterogeneidad del medio geológico introduce en el proyecto de obra subterránea un alto grado de incertidumbre que debe ser debidamente gestionado a fin de reducir los riesgos asociados, que son fundamentalmente de tipo geotécnico. Entre los principales problemas a los que se enfrenta la Mecánica de Rocas moderna en el ámbito de la construcción subterránea, se encuentran la fluencia de roca en túneles (squeezing) y la rotura de pilares de carbón. Es ampliamente conocido que su aparición causa importantes perjuicios en el coste y la seguridad de los proyectos por lo que su estudio, ha estado tradicionalmente vinculado a la predicción de su ocurrencia. Entre las soluciones existentes para la determinación de estos problemas se encuentran las que se basan en métodos analíticos y numéricos. Estas metodologías son capaces de proporcionar un alto nivel de representatividad respecto del comportamiento geotécnico real, sin embargo, su utilización solo es posible cuando se dispone de una suficiente caracterización geotécnica y por tanto de una detallada definición de los parámetros que alimentan los complejos modelos constitutivos y criterios de rotura que los fenómenos estudiados requieren. Como es lógico, este nivel de definición solo es posible cuando se alcanzan etapas avanzadas de proyecto, incluso durante la propia construcción, a fin de calibrar adecuadamente los parámetros introducidos en los modelos, lo que supone una limitación de uso en etapas iniciales, cuando su predicción tiene verdadero sentido. Por su parte, los métodos empíricos permiten proporcionar soluciones a estos complejos problemas de un modo sencillo, con una baja parametrización y, dado su eminente enfoque observacional, de gran fiabilidad cuando se implementan sobre condiciones de contorno similares a las originales. La sencillez y escasez de los parámetros utilizados permiten a estas metodologías ser utilizadas desde las fases preliminares del proyecto, ya que estos constituyen en general, información habitual de fácil y económica adquisición. Este aspecto permite por tanto incorporar la predicción desde el principio del proceso de diseño, anticipando el riesgo en origen. En esta tesis doctoral, se presenta una nueva metodología empírica que sirve para proporcionar predicciones para la ocurrencia de squeezing y el fallo de pilares de carbón basada en una extensa recopilación de información de casos reales de túneles y minas en las que ambos fenómenos fueron evaluados. Esta información, recogida de referencias bibliográficas de prestigio, ha permitido recopilar una de las más extensas bases de datos existentes hasta la fecha relativa a estos fenómenos, lo que supone en sí mismo una importante contribución sobre el estado del arte. Con toda esta información, y con la ayuda de la teoría de clasificadores estadísticos, se ha implementado sobre las bases de datos un clasificador lineal de tipo regresión logística que permite hacer predicciones sobre la ocurrencia de ambos fenómenos en términos de probabilidad, y por tanto ponderar la incertidumbre asociada a la heterogeneidad incorporada por el medio geológico. Este aspecto del desarrollo es el verdadero valor añadido proporcionado por la tesis y la principal ventaja de la solución propuesta respecto de otras metodologías empíricas. Esta capacidad de ponderación probabilística permite al clasificador constituir una solución muy interesante como metodología para la evaluación de riesgo geotécnico y la toma de decisiones. De hecho, y como ejercicio de validación práctica, se ha implementado la solución desarrollada en un modelo coste-beneficio asociado a la optimización del diseño de pilares involucrados en una de mina “virtual” explotada por tajos largos. La capacidad del clasificador para cuantificar la probabilidad de fallo del diseño, junto con una adecuada cuantificación de las consecuencias de ese fallo, ha permitido definir una ley de riesgo que se ha incorporado al balance de costes y beneficios, que es capaz, a partir del redimensionamiento iterativo del sistema de pilares y de la propia configuración de la mina, maximizar el resultado económico del proyecto minero bajo unas condiciones de seguridad aceptables, fijadas de antemano. Geological media variability introduces to the subterranean project a high grade of uncertainty that should be properly managed with the aim to reduce the associated risks, which are mainly geotechnical. Among the major problems facing the modern Rock Mechanics in the field of underground construction are both, the rock squeezing while tunneling and the failure of coal pillars. Given their harmfulness to the cost and safety of the projects, their study has been traditionally linked to the determination of its occurrence. Among the existing solutions for the determination of these problems are those that are based on analytical and numerical methods. Those methodologies allow providing a high level of reliability of the geotechnical behavior, and therefore a detailed definition of the parameters that feed the complex constitutive models and failure criteria that require the studied phenomena. Obviously, this level of definition is only possible when advanced stages of the project are achieved and even during construction in order to properly calibrate the parameters entered in the models, which suppose a limited use in early stages, when the prediction has true sense. Meanwhile, empirical methods provide solutions to these complex problems in a simple way, with low parameterization and, given his observational scope, with highly reliability when implemented on similar conditions to the original context. The simplicity and scarcity of the parameters used allow these methodologies be applied in the early stages of the project, since that information should be commonly easy and cheaply to get. This aspect can therefore incorporate the prediction from the beginning of the design process, anticipating the risk beforehand. This thesis, based on the extensive data collection of case histories of tunnels and underground mines, presents a novel empirical approach used to provide predictions for the occurrence of both, squeezing and coal pillars failures. The information has been collected from prestigious references, providing one of the largest databases to date concerning phenomena, a fact which provides an important contribution to the state of the art. With all this information, and with the aid of the theory of statistical classifiers, it has been implemented on both databases, a type linear logistic regression classifier that allows predictions about the occurrence of these phenomena in terms of probability, and therefore weighting the uncertainty associated with geological variability. This aspect of the development is the real added value provided by the thesis and the main advantage of the proposed solution over other empirical methodologies. This probabilistic weighting capacity, allows being the classifier a very interesting methodology for the evaluation of geotechnical risk and decision making. In fact, in order to provide a practical validation, we have implemented the developed solution within a cost-benefit analysis associated with the optimization of the design of coal pillar systems involved in a "virtual" longwall mine. The ability of the classifier to quantify the probability of failure of the design along with proper quantification of the consequences of that failure, has allowed defining a risk law which is introduced into the cost-benefits model, which is able, from iterative resizing of the pillar system and the configuration of the mine, maximize the economic performance of the mining project under acceptable safety conditions established beforehand.

Influence of high aluminium content on the mechanical properties of directionally solidified multicrystalline silicon

The purpose of this research is the mechanical characterisation of multicrystalline silicon crystallised from silicon feedstock with a high content of aluminium for photovoltaic applications. The mechanical strength, fracture toughness and elastic modulus were measured at different positions within the multicrystalline silicon block to quantify the impact of the segregation of impurities on these mechanical properties. Aluminium segregated to the top of the block and caused extensive micro-cracking of the silicon matrix due to the thermal mismatch between silicon and the aluminium inclusions. Silicon nitride inclusions reduced the fracture toughness and caused failure by radial cracking in its surroundings due to its thermal mismatch with silicon. However, silicon carbide increased the fracture toughness and elastic modulus of silicon.

A numerical study of the influence of microvoids in the transverse mechanical response of unidirectional composites

The effect of porosity on the transverse mechanical properties of unidirectional fiber-reinforced composites is studied by means of computational micromechanics. The composite behavior is simulated by the finite element analysis of a representative volume element of the composite microstructure in which the random distribution of fibers and the voids are explicitly included. Two types of voids – interfiber voids and matrix voids – were included in the microstructure and the actual damage mechanisms in the composite, namely matrix and interface failure, were accounted for. It was found that porosity (in the range 1–5%) led to a large reduction in the transverse strength and the influence of both types of voids in the onset and propagation of damage throughout the microstructure was studied under transverse tension and compression. Finally, the failure locus of the composite lamina under transverse tension/compression and out-of-plane shear was obtained by means of computational micromechanics and compared with the predictions of Puck’s model and with experimental data available in the literature. The results show that the strength of composites is significantly reduced by the presence of voids

Micromechanical basis for shear strength of rock discontinuities

The theoretical basis for evaluating shear strength in rock joints is presented and used to derive an equation that governs the relationship between tangential and normal stress on the joint during situations of slippage between the joint faces. The dependent variables include geometric dilatancy, the instantaneous friction angle, and a parameter that considers joint surface roughness. The effect roughness is studied, and the aforementioned formula is used to analyse joints under different conditions. A mathematical expression is deduced that explains Barton's value for the joint roughness coefficient (JRC) according to the roughness geometry. In particular, when the Hoek and Brown failure criterion is used for a rock in the contact with the surface roughness plane, it is possible to determine the shear strength of the joint as a function of the relationship between the uniaxial compressive strength of the wall with the normal stress acting on the wall. Finally, theoretical results obtained for the geometry of a three-dimensional joint are compared with those of the Barton's formulation

Analysis of the damage domains of sbo sequences with rcp passive thermal shutdown

The integrated Safety Assessment (ISA) methodology, developed by the Spanish Nuclear Safety Council (CSN), has been applied to a thermal-hydraulic analysis of PWR Station Blackout (SBO) sequences in the context of the IDPSA (Integrated Deterministic-Probabilistic Safety Assessment) network objectives. The ISA methodology allows obtaining the damage domain (the region of the uncertain parameters space where the damage limit is exceeded) for each sequence of interest as a function of the operator actuations times. Given a particular safety limit or damage limit, several data of every sequence are necessary in order to obtain the exceedance frequency of that limit. In this application these data are obtained from the results of the simulations performed with MAAP code transients inside each damage domain and the time-density probability distributions of the manual actions. Damage limits that have been taken into account within this analysis are: local cladding damage (PCT>1477 K); local fuel melting (T>2499 K); fuel relocation in lower plenum and vessel failure. Therefore, to every one of these damage variables corresponds a different damage domain. The operation of the new passive thermal shutdown seals developed by several companies since Fukushima accident is considered in the paper. The results show the capability and necessity of the ISA methodology, or similar, in order to obtain accurate results that take into account time uncertainties.

Methodology based on FBG sensors for monitoring of FRP-strengthened beams

Advanced composite materials are increasingly used in the strengthening of reinforced concrete (RC) structures. The use of externally bonded strips made of fibre-reinforced plastics (FRP) as strengthening method has gained widespread acceptance in recent years since it has many advantages over the traditional techniques. However, unfortunately, this strengthening method is often associated with a brittle and sudden failure caused by some form of FRP bond failure, originated at the termination of the FRP material or at intermediate areas in the vicinity of flexural cracks in the RC beam. Up to date, little effort in the early prediction of the debonding in its initial instants even though this effect is not noticeable by simple visual observation. An early detection of this phenomenon might help in taking actions to prevent future catastrophes. Fibre-optic Bragg grating (FBG) sensors are able to measure strains locally with high resolution and accuracy. Furthermore, as their physical size is extremely small compared with other strain measuring components, it enables to be embedded at the concrete-FRP interface for determining the strain distribution without influencing the mechanical properties of the host materials. This paper shows the development of a debonding identification methodology based on strains experimentally measured. For, it a simplified model is implemented to simulate the behaviour of FRP-strengthened reinforced concrete beams. This model is taken as a basis to. develop an model updating procedure able to detect minor debonding at the concrete-FRP interface from experimental strains obtained by using FBG sensors embedded at the interface

Strain rate effect on semi‐crystalline plla mechanical properties measured by instrumented indentation tests

Poly(L‐lactide) is a widely studied biomaterial, currently approved for use in a range of medical devices. Its mechanical properties can be tailored giving the material different crystallinity degrees. PLLA presents a complex non‐linear behaviour that depends not only on structural parameters such as crystallinity degree but also on external parameters such as strain rate and temperature. Failure of polymeric implants is attributed to their intrinsic time‐dependent performance under static loading conditions.

Towards an optimal implementation of cascade

The aim of this contribution is to study the modifications of Cascade, comparing them with the original protocol on the grounds of a full set of parameters, so that the effect of these modifications can be fairly assessed. A number of simulations were performed to study not only the efficiency but also other characteristics of the protocol that are important for its practical application, such as the number of communications and the failure probability. Note that, although it is generally believed that the only price to pay for an improved efficiency is an increased interactivity, when looking at all the significant magnitudes a different view emerges, showing that, for instance, the failure probability eliminate some the supposed advantages of these improvements.