Groundwater recharge estimate at Alto Rio Grande - MG watershed

Springs are outcrops of aquifers surface, and the water cycle in this environment pass through the recharge, generally defined as the amount of water added to the aquifer, which may occur locally from rainwater infiltration. This study uses the Water Table Fluctuation (WTF) method to estimate the direct recharge and a groundwater balance to estimate the deep recharge on unconfined aquifers. The WTF method employs data of the aquifer water levels and its specific yield to estimate the direct recharge. The groundwater balance considers the direct recharge estimated by the WTF method, as the water input in the system and outputs as the base flow and deep recharge. The recharge was estimated at four areas at the watershed of Alto Rio Grande city, Minas Gerais (MG) state, in Brazil. The direct recharge estimate was 121.11; 64.62; 83.99; 152.46 (mm/year) for the L1, L2, M1 and M2 areas. The effect of the presence of forest in the recharge area can prevail over slope of relief, allowing more direct recharge, even in sources with steeper relief. The runoff from the springs in the study period exceeded the direct recharge, indicating a situation in which the saturated zone feeds the vadose zone. The annual flow was above the direct recharge pointing a situation of over exploitation of the aquifer, a non sustainable situation. The specific yield of the aquifers could also have been underestimated.

Improved order fulfillment in paper production

For the paper mill profitability it is crucial to minimize overproduction and underproduction. Overproduction and underproduction both generate undesired costs and profit losses in paper mill production. This master’s thesis examines paper production order fulfillment subject from paper production level point of view. Research and development approach is selected due to clarification requirements in lately implemented manufacturing execution system. Manufacturing execution systems are generally expected to offer reliable and accurate information about mill production details. However, confusions are likely to occur after implementation of new manufacturing execution system. These confusions are usually harmful and become cumulatively more influential the longer they keep occurring. In this master’s thesis is presented actions to improve order fulfillment at paper mill production level. Central points of the improvement actions are a model for successful order fulfillment in paper mill production and manufacturing execution system catalogue configuration redesign. Improvement actions are implemented in Jokilaakso paper production plant and it is examined as a case study. In the end of this master’s thesis is presented performance measurements which demonstrate order fulfillment from case Jokilaakso.

Lactated Ringer's solution or 0.9% sodium chloride as fluid therapy in pigeons (Columba livia) submitted to humerus osteosynthesis

The study aimed to compare the effects of intraosseous infusion of lactated Ringer's and 0.9% sodium chloride solutions on the electrolytes and acid-base balance in pigeons submitted to humerus osteosynthesis. Eighteen pigeons were undergoing to isoflurane anesthesia by an avalvular circuit system. They were randomly assigned into two groups (n=9) receiving lactated Ringer's solution (LR) or 0.9% sodium chloride (SC), in a continuous infusion rate of 20mL/kg/h, by using an intraosseous catheter into the tibiotarsus during 60-minute anesthetic procedure. Heart rate (HR), and respiratory rate (RR) were measured every 10 min. Venous blood samples were collected at 0, 30 and 60 minutes to analyze blood pH, PvCO2, HCO3 -, Na+ and K+. Blood gases and electrolytes showed respiratory acidosis in both groups during induction, under physical restraint. This acidosis was evidenced by a decrease of pH since 0 min, associated with a compensatory response, observed by increasing of HCO3 - concentration, at 30 and 60 min. It was not observed any changes on Na+ and K+ serum concentrations. According to the results, there is no reason for choosing one of the two solutions, and it could be concluded that both fluid therapy solutions do not promote any impact on acid-base balance and electrolyte concentrations in pigeons submitted to humerus osteosynthesis.

Modeling of Liquid-Solid Flow in Industrial Scale

In the present work, liquid-solid flow in industrial scale is modeled using the commercial software of Computational Fluid Dynamics (CFD) ANSYS Fluent 14.5. In literature, there are few studies on liquid-solid flow in industrial scale, but any information about the particular case with modified geometry cannot be found. The aim of this thesis is to describe the strengths and weaknesses of the multiphase models, when a large-scale application is studied within liquid-solid flow, including the boundary-layer characteristics. The results indicate that the selection of the most appropriate multiphase model depends on the flow regime. Thus, careful estimations of the flow regime are recommended to be done before modeling. The computational tool is developed for this purpose during this thesis. The homogeneous multiphase model is valid only for homogeneous suspension, the discrete phase model (DPM) is recommended for homogeneous and heterogeneous suspension where pipe Froude number is greater than 1.0, while the mixture and Eulerian models are able to predict also flow regimes, where pipe Froude number is smaller than 1.0 and particles tend to settle. With increasing material density ratio and decreasing pipe Froude number, the Eulerian model gives the most accurate results, because it does not include simplifications in Navier-Stokes equations like the other models. In addition, the results indicate that the potential location of erosion in the pipe depends on material density ratio. Possible sedimentation of particles can cause erosion and increase pressure drop as well. In the pipe bend, especially secondary flows, perpendicular to the main flow, affect the location of erosion.

Glyphosate translocation in hairy fleabane (Conyza bonariensis) biotypes

The objective of this work was to evaluate the translocation of glyphosate in C. bonariensis plants resistant and susceptible to that herbicide. The 14C-glyphosate was mixed with commercial gyhphosate (800 g ha-1) and applied on the center of the adaxial face of a third node leaf, using a micro syringe, and adding 10 µL of a solution with specific activity of 1,400 Bq, 45 days after plant emergence. The concentration of the glyphosate translocated in the plant was evaluated at time intervals of 6, 12, 36 and 72 hours after being applied on the application leaf, stem, roots and leaves. Ten hours after treatment application, the distribution of the product in the application leaf, divided into base, center and apex, was also evaluated by measuring the radiation emitted by 14C-glyphosate in a liquid scintillation spectrometer. Greater glyphosate retention was observed in the resistant biotype leaf, approximately 90% of the total absorbed up to 72 hours. In the susceptible biotype, this value was close to 70% in the same period. Susceptible biotype leaves, stem and roots showed greater concentration of glyphosate, indicating greater translocation efficiency in this biotype. In the resistant biotype, the herbicide accumulated in greater quantity at the apex and center of the application leaf, while in the susceptible biotype greater accumulation was observed at the base and center leaf. Thus, it can be stated that the resistance mechanism is related to the differential translocation of this herbicide in the biotypes.

Growth inhibitors in turfgrass

Well-maintained lawns are comfortable and safe places for leisure activities and sports practice, and they also bring environmental benefits; for example, they reduce soil exposure to erosion and releases atmospheric CO2, thus reducing the greenhouse effect. However, regardless of the purpose of use or the choice of the plant species to form the lawn, the highest costs involve cutting that is needed to keep the turfgrass at its appropriate height. Successive lawn cutting operations are necessary basically because of the vegetative and reproductive growth of turfgrass which, in Brazil, occurs mainly from October to March. Expenditures with successive mechanical cuttings have fostered the search of alternative procedures to keep lawn plants at appropriate height, such as the use of plant growth inhibitors, an increasingly interesting procedure. Since the use of this technology in Brazil is still at its early stage, the aim of this literature review is to examine aspects associated with lawn management by using growth inhibitors. Another alternative is to increase the knowledge of the classification and rational application of the different compounds currently available in the market.

CARDINAL TEMPERATURES FOR GERMINATION OF THE MEDICINAL ANDDESERT PLANT, Calotropis procera

ABSTRACT Calotropis procera, Apocynaceae, is a wild perennial shrub that originated in the Persian deserts. It is known to provide key resources in degraded ecosystems to about 80 animal species. C. procera is regenerated by seed and produces lots of small seeds that are dispersed by wind; nonetheless, its density is very low. The purpose of this study is to estimate the cardinal temperatures including the base, optimum, and maximum temperatures of Calotropis procera looking at two different ecotypes in the Iranian desert. The germination behavior of C. procera seeds was tested at temperature regimens of 0, 5, 10, 15, 20, 25, 30, 35 and 40oC and was analyzed using linear regression models. The rate of germination increased between base and optimum thermal conditions, and decreased between optimum and maximum thermal conditions. The base, optimum and maximum temperatures for germination of C. procera seeds were estimated at 19.10, 30.75 and 47.80 oC for the Fars and 20.00, 31.82 and 49.69oC for the Zahedan desert, respectively. Temperature and germination were rated to determine the seeding dates of the C. procera. Overall, cardinal temperatures for germination were dependent on local climate characteristics for the range of adaptations in plant growth of the given species.

Erythrocytes may contain a ouabain-insensitive K+-ATPase which plays a role in internal K+ balance

Erythrocytes are useful in evaluating K+ transport pathways involved in internal K+ balance. Several forms of H+,K+-ATPase have been described in nephron segments active in K+ transport. Furthermore, the activity of a ouabain-insensitive isoform of H+,K+-ATPase expressed in collecting duct cells may be modulated by acid-base status. Various assays were performed to determine if a ouabain-insensitive K+-ATPase is present in rat erythrocytes and, if so, whether it plays a role in internal K+ balance. Kinetic studies demonstrated that maximal stimulation of enzyme activity was achieved with 2.5 mM K+ at pH 7.4. Subsequent experiments were performed on erythrocyte membranes collected from animals submitted to varying degrees of K+ homeostasis: control rats, K+-depleted rats, K+-loaded rats, and rats rendered hyperkalemic due to acute renal failure. As observed in the collecting duct cell studies, there was a significant decrease in the activity of ouabain-insensitive K+-ATPase in the erythrocytes of both K+-loaded and metabolically alkalotic K+-depleted rats. However, this enzyme activity in erythrocyte membranes of rats with metabolic acidosis-related hyperkalemia was similar to that of control animals. This finding may be interpreted as resulting from two potentially modulating factors: the stimulating effect that metabolic acidosis has on K+-ATPase and the counteracting effect that hyperkalemia and uremia have on metabolic acidosis. In summary, we present evidence of a ouabain-insensitive K+-ATPase in erythrocytes, whose activity is modulated by acid-base status and K+ levels.

Antibacterial activity of indole alkaloids from Aspidosperma ramiflorum

We evaluated the antibacterial activities of the crude methanol extract, fractions (I-V) obtained after acid-base extraction and pure compounds from the stem bark of Aspidosperma ramiflorum. The minimum inhibitory concentration (MIC) was determined by the microdilution technique in Mueller-Hinton broth. Inoculates were prepared in this medium from 24-h broth cultures of bacteria (10(7) CFU/mL). Microtiter plates were incubated at 37ºC and the MICs were recorded after 24 h of incubation. Two susceptibility endpoints were recorded for each isolate. The crude methanol extract presented moderate activity against the Gram-positive bacteria B. subtilis (MIC = 250 µg/mL) and S. aureus (MIC = 500 µg/mL), and was inactive against the Gram-negative bacteria E. coli and P. aeruginosa (MIC > 1000 µg/mL). Fractions I and II were inactive against standard strains at concentrations of <=1000 µg/mL and fraction III displayed moderate antibacterial activity against B. subtilis (MIC = 500 µg/mL) and S. aureus (MIC = 250 µg/mL). Fraction IV showed high activity against B. subtilis and S. aureus (MIC = 15.6 µg/mL) and moderate activity against E. coli and P. aeruginosa (MIC = 250 µg/mL). Fraction V presented high activity against B. subtilis (MIC = 15.6 µg/mL) and S. aureus (MIC = 31.3 µg/mL) and was inactive against Gram-negative bacteria (MIC > 1000 µg/mL). Fractions III, IV and V were then submitted to bioassay-guided fractionation by silica gel column chromatography, yielding individual purified ramiflorines A and B. Both ramiflorines showed significant activity against S. aureus (MIC = 25 µg/mL) and E. faecalis (MIC = 50 µg/mL), with EC50 of 8 and 2.5 µg/mL for ramiflorines A and B, respectively, against S. aureus. These results are promising, showing that these compounds are biologically active against Gram-positive bacteria.

Ohuiden päällystyskerrosten applikointi puukuitupohjaisille materiaaleille

Työn aiheena oli tutkia vaahdon soveltuvuutta ohuiden päällystyskerrosten applikointiin paperin tai kartongin pinnalle. Paperia ja kartonkia päällystetään teollisessa mittakaavassa eri menetelmillä, mutta niille kaikille yhteistä on päällystyspastan laimentaminen vedellä ennen applikointia ja laimennusveden haihduttaminen applikoinnin jälkeen päällysteen asettamiseksi. Laimennus on tärkeää pastan komponenttien tasaisen levittämisen vuoksi, mutta veden haihduttaminen kuluttaa valtavasti energiaa. Tekstiiliteollisuudessa on saavutettu merkittäviä säästöjä kuivausenergiassa korvaamalla laajalti vedellä laimentaminen vaahdottamisella. Diplomityön kirjallisessa osassa käytiin läpi vaahdon kemiallisia ja fysikaalisia ominaisuuksia sekä selvitettiin mitä kemikaaleja ja laitteita vaahdotukseen käytetään. Lisäksi luotiin katsaus vaahtoprosessien käyttöön tekstiiliteollisuudessa ja muilla aloilla. Kokeellinen osa koostui esikokeista, joissa selvitettiin pastan koostumuksen vaikutuksia vaahtoamiseen, ja pilot-mittakaavan koeajoista, joissa esikokeiden tuloksia hyödynnettiin. Esikokeissa huomiota kiinnitettiin varsinkin eri polyvinyylialkoholien (PVA) seosten erinomaiseen vaahtoavuuteen. Pilot-koeajoissa vaahtopäällystys vaikutti lupaavalta menetelmältä, joskaan täysin tyydyttävää päällystystulosta ei saavutettu. Suurimpana ongelmana esiintyi ilman pääseminen pohjapaperin ja päällysteen väliin ja siitä seuraava huono päällystejälki. Toisen ongelmakokonaisuuden muodostivat päällysteeseen jäävät reiät. Vaahtopäällystys vaikuttaa lupaavalta tekniikalta ohuiden päällystekerrosten applikointiin, mutta pastareseptejä tulee optimoida ja ratkaista päällysteen alle pääsevän ilman ongelma.

Weld joint characteristics by nano-materials addition

The need for industries to remain competitive in the welding business, has created necessity to develop innovative processes that can exceed customer’s demand. Significant development in improving weld efficiency, during the past decades, still have their drawbacks, specifically in the weld strength properties. The recent innovative technologies have created smallest possible solid material known as nanomaterial and their introduction in welding production has improved the weld strength properties and to overcome unstable microstructures in the weld. This study utilizes a qualitative research method, to elaborate the methods of introducing nanomaterial to the weldments and the characteristic of the welds produced by different welding processes. The study mainly focuses on changes in the microstructural formation and strength properties on the welded joint and also discusses those factors influencing such improvements, due to the addition of nanomaterials. The effect of nanomaterial addition in welding process modifies the physics of joining region, thereby, resulting in significant improvement in the strength properties, with stable microstructure in the weld. The addition of nanomaterials in the welding processes are, through coating on base metal, addition in filler metal and utilizing nanostructured base metal. However, due to its insignificant size, the addition of nanomaterials directly to the weld, would poses complications. The factors having major influence on the joint integrity are dispersion of nanomaterials, characteristics of the nanomaterials, quantity of nanomaterials and selection of nanomaterials. The addition of nanomaterials does not affect the fundamental properties and characteristics of base metals and the filler metal. However, in some cases, the addition of nanomaterials lead to the deterioration of the joint properties by unstable microstructural formations. Still research are ongoing to achieve high joint integrity, in various materials through different welding processes and also on other factors that influence the joint strength.

Item-level life-cycle model for maintenance network – from cost to additional value

The importance of industrial maintenance has been emphasized during the last decades; it is no longer a mere cost item, but one of the mainstays of business. Market conditions have worsened lately, investments in production assets have decreased, and at the same time competition has changed from taking place between companies to competition between networks. Companies have focused on their core functions and outsourced support services, like maintenance, above all to decrease costs. This new phenomenon has led to increasing formation of business networks. As a result, a growing need for new kinds of tools for managing these networks effectively has arisen. Maintenance costs are usually a notable part of the life-cycle costs of an item, and it is important to be able to plan the future maintenance operations for the strategic period of the company or for the whole life-cycle period of the item. This thesis introduces an itemlevel life-cycle model (LCM) for industrial maintenance networks. The term item is used as a common definition for a part, a component, a piece of equipment etc. The constructed LCM is a working tool for a maintenance network (consisting of customer companies that buy maintenance services and various supplier companies). Each network member is able to input their own cost and profit data related to the maintenance services of one item. As a result, the model calculates the net present values of maintenance costs and profits and presents them from the points of view of all the network members. The thesis indicates that previous LCMs for calculating maintenance costs have often been very case-specific, suitable only for the item in question, and they have also been constructed for the needs of a single company, without the network perspective. The developed LCM is a proper tool for the decision making of maintenance services in the network environment; it enables analysing the past and making scenarios for the future, and offers choices between alternative maintenance operations. The LCM is also suitable for small companies in building active networks to offer outsourcing services for large companies. The research introduces also a five-step constructing process for designing a life-cycle costing model in the network environment. This five-step designing process defines model components and structure throughout the iteration and exploitation of user feedback. The same method can be followed to develop other models. The thesis contributes to the literature of value and value elements of maintenance services. It examines the value of maintenance services from the perspective of different maintenance network members and presents established value element lists for the customer and the service provider. These value element lists enable making value visible in the maintenance operations of a networked business. The LCM added with value thinking promotes the notion of maintenance from a “cost maker” towards a “value creator”.

Crescimento da firma e comércio exterior: revisitando a teoria de Adrian Wood

This paper analyzes the growth of the firm by foreign trade. The theory of Adrian Wood is revisited for the analysis of growth and profit trade-off and improved to cope with growth by exports. The main outcome of this paper is that low domestic demand can be a very important factor to firm choices growth by foreign market. However, the growth of domestic demand does not necessarily reduce exports.

Tuotesuunnittelu direktiiviperustaisesti

Onnistuneen tuotekehitysprojektin läpivieminen vaatii huolellisen alkusuunnittelun ennen varsinaista tuotteen kehityksen aloitusta. Projektin läpiviemiseksi esitetään usein malleja joissa tuotekehitysprojektissa edetään yksi vaihe kerrallaan ja siirrytään seuraavaan vasta, kun edellinen on valmis. Tämän perinteisen mallin rinnalle on tullut DFMA-suunnittelu, jossa murretaan kommunikaatiomuuri suunnittelun ja valmistuksen väliltä ja useita vaiheita tehdään samanaikaisesta. Näin saadaan valmistus- ja kokoonpanoystävällisiä tuotteita, joilla tuotteesta saatava kate voidaan maksimoida samalla kun tuotteen laatua saadaan parannettua. Teknisen kehityksen lisäksi on tuotekehitysprosessissa erottamattomana osana direktiivien asettamien vaatimusten huomioon ottaminen. Jo lähes kaikissa tuotteissa on oltava CE-merkintä. CE-merkinnällä tuotteen valmistaja ottaa täyden vastuun siitä, että tuote täyttää sitä koskevien direktiivien asettamat vaatimukset vaatimustenmukaisuudesta. Direktiivien asettamat vaatimukset on hyvä tiedostaa jo tuotteen suunnittelun alkuvaiheista lähtien, jotta nämä osataan ottaa heti huomioon ja jälkikäteen tehtäviltä muutoksilta vältytään. Teknisten ratkaisujen lisäksi tuotteen dokumentoinnilla on suuri rooli vaatimustenmukaisuuden täyttämisessä. Tuotteesta tulee koota tekninen tiedosto, joka sisältää kaikki tarpeelliset dokumentit, joilla tuotteen vaatimustenmukaisuus voidaan todeta. Teknisen tiedoston vaatimukset on hyvä tiedostaa jo suunnittelun alusta lähtien, jotta tarvittavat dokumentit osataan kerätä projektin aikana tekniseen tiedostoon. Tässä työssä kehitettiin peltier-jäähdytin, jollaiselle asiakkailta saadun palautteen perusteella oli markkinoilla tarve. Jäähdyttimen suunnittelussa käytettiin DFMA:n keinoja yksinkertaistamaan kokoonpanoa. Jäähdyttimelle tehtiin vaatimustenmukaisuustarkastelu, missä tarkasteltiin peltier-jäähdytintä koskevien direktiivien asettamia vaatimuksia ja mitä asioita näiden vaatimusten täyttämiseksi tuli huomioida.

Fantasiakirjallisuuden muuttuvia tyttöjä

Kirjallisuusarvostelu