Recovery and refining of manganese as by-product from hydrometallurgical processes

The consumption of manganese is increasing, but huge amounts of manganese still end up in waste in hydrometallurgical processes. The recovery of manganese from multi-metal solutions at low concentrations may not be economical. In addition, poor iron control typically prevents the production of high purity manganese. Separation of iron from manganese can be done with chemical precipitation or solvent extraction methods. Combined carbonate precipitation with air oxidation is a feasible method to separate iron and manganese due to the fast kinetics, good controllability and economical reagents. In addition the leaching of manganese carbonate is easier and less acid consuming than that of hydroxide or sulfide precipitates. Selective iron removal with great efficiency from MnSO4 solution is achieved by combined oxygen or air oxidation and CaCO3 precipitation at pH > 5.8 and at a redox potential of > 200 mV. In order to avoid gypsum formation, soda ash should be used instead of limestone. In such case, however, extra attention needs to be paid on the reagents mole ratios in order to avoid manganese coprecipitation. After iron removal, pure MnSO4 solution was obtained by solvent extraction using organophosphorus reagents, di-(2-ethylhexyl)phosphoric acid (D2EHPA) and bis(2,4,4- trimethylpentyl)phosphinic acid (CYANEX 272). The Mn/Ca and Mn/Mg selectivities can be increased by decreasing the temperature from the commonly used temperatures (40 –60oC) to 5oC. The extraction order of D2EHPA (Ca before Mn) at low temperature remains unchanged but the lowering of temperature causes an increase in viscosity and slower phase separation. Of these regents, CYANEX 272 is selective for Mn over Ca and, therefore, it would be the better choice if there is Ca present in solution. A three-stage Mn extraction followed by a two-stage scrubbing and two-stage sulfuric acid stripping is an effective method of producing a very pure MnSO4 intermediate solution for further processing. From the intermediate MnSO4 some special Mn- products for ion exchange applications were synthesized and studied. Three types of octahedrally coordinated manganese oxide materials as an alternative final product for manganese were chosen for synthesis: layer structured Nabirnessite, tunnel structured Mg-todorokite and K-kryptomelane. As an alternative source of pure MnSO4 intermediate, kryptomelane was synthesized by using a synthetic hydrometallurgical tailings. The results show that the studied OMS materials adsorb selectively Cu, Ni, Cd and K in the presence of Ca and Mg. It was also found that the exchange rates were reasonably high due to the small particle dimensions. Materials are stable in the studied conditions and their maximum Cu uptake capacity was 1.3 mmol/g. Competitive uptake of metals and acid was studied using equilibrium, batch kinetic and fixed-bed measurements. The experimental data was correlated with a dynamic model, which also accounts for the dissolution of the framework manganese. Manganese oxide micro-crystals were also bound onto silica to prepare a composite material having a particle size large enough to be used in column separation experiments. The MnOx/SiO2 ratio was found to affect significantly the properties of the composite. The higher the ratio, the lower is the specific surface area, the pore volume and the pore size. On the other hand, higher amount of silica binder gives composites better mechanical properties. Birnesite and todorokite can be aggregated successfully with colloidal silica at pH 4 and with MnO2/SiO2 weight ratio of 0.7. The best gelation and drying temperature was 110oC and sufficiently strong composites were obtained by additional heat-treatment at 250oC for 2 h. The results show that silica–supported MnO2 materials can be utilized to separate copper from nickel and cadmium. The behavior of the composites can be explained reasonably well with the presented model and the parameters estimated from the data of the unsupported oxides. The metal uptake capacities of the prepared materials were quite small. For example, the final copper loading was 0.14 mmol/gMnO2. According to the results the special MnO2 materials are potential for a specific environmental application to uptake harmful metal ions.

Myyntivalmennuksen ja työympäristön tuen vaikutukset asiakaslähtöisen myyntityön käyttämiseen

Tämän tutkielman tavoitteena oli selvittää myyntivalmennuksen ja työympäristön tuen vaikutuksia asiakaslähtöisen myyntityön käyttämiseen. Tutkimuksessa selvitettiin myös, minkälainen on asiakaslähtöinen myyntiprosessi. Kirjallisuuskatsauksessa löydettiin useita tutkimusaukkoja avainkäsitteiden tutkimuskentästä, joihin tämä tutkielma osaltaan vastasi. Tutkielman kohdeyrityksenä käytettiin jälleenmyyntialalla toimivaa kodinkoneketjua, jonka noin 30 myymälästä valittiin kolme myymälää tarkempaa tutkimusta varten. Empiirinen osa suoritettiin haastattelemalla kuutta myyjää ja kolmea esimiestä näistä kolmesta myymälästä, ja suorittamalla lyhennetty versio SOCO-kyselystä 11 myyjälle, kolmelle esimiehelle ja 78 asiakkaalle. Tutkimuksessa käytettiin hyödyksi sekä kvalitatiivisia, että kvantitatiivisia tutkimusmenetelmiä. Johtopäätöksinä voidaan todeta, että myyntivalmennus ja työympäristöstä saatu tuki vaikuttaa myyjiin sekä asiakas-, että myyntilähtöisellä tavalla. Myyntiprosessitaitojen ja mukautuvan myyntityön harjoitteleminen valmennuksessa lisää myyjien asiakaslähtöisyyttä, mutta tuotekoulutuksen puuttuminen osana valmennusta ei kehitä myyjien argumentointitaitoja, jolloin myyjien myyntilähtöisyys lisääntyy. Työympäristöstä saadun tuen tulisi olla johdonmukaista, jotta myyjille asetetut käyttäytymisvaatimukset ja palkitsemismenetelmät eivät olisi ristiriidassa keskenään. Kohdeyrityksen myyjät arvioitiin olevan sekä myyjien, esimiesten että asiakkaiden mielestä enemmän asiakas-, kuin myyntilähtöisiä.

Motivational Influences on Transfer: Dimensions and Boundary Conditions

The focus of this dissertation is the motivational influences on transfer in higher education and professional training contexts. To estimate these motivational influences, the dissertation includes seven individual studies that are structured in two parts. Part I, Dimensions, aims at identifying the dimensionality of motivation to transfer and its structural relations with training-related antecedents and outcomes. Part II, Boundary Conditions, aims at testing the predictive validity of motivation theories used in contemporary training research under different study conditions. Data in this dissertation was gathered from multi-item questionnaires, which were analyzed differently in Part I and Part II. Studies in Part I employed exploratory and confirmatory factor analysis, structural equation modeling, partial least squares (PLS) path modeling, and mediation analysis. Studies in Part II used artifact distribution meta-analysis, (nested) subgroup analysis, and weighted least squares (WLS) multiple regression. Results demonstrate that motivation to transfer can be conceptualized as a three-dimensional construct, including autonomous motivation to transfer, controlled motivation to transfer, and intention to transfer, given a theoretical framework informed by expectancy theory, self-determination theory, and the theory of planned behavior. Results also demonstrate that a range of boundary conditions moderates motivational influences on transfer. To test the predictive validity of expectancy theory, social cognitive theory, and the theory of goal orientations under different study settings, a total of 17 boundary conditions were meta-analyzed, including age; assessment criterion; assessment source; attendance policy; collaboration among trainees; computer support; instruction; instrument used to measure motivation; level of education; publication type; social training context; SS/SMC bias; study setting; survey modality; type of knowledge being trained; use of a control group; and work context. Together, the findings cumulated in this thesis support the basic premise that motivation is centrally important for transfer, but that motivational influences need to be understood from a more differentiated perspective than commonly found in the literature, in order to account for several dimensions and boundary conditions. The results of this dissertation across the seven individual studies are reflected in terms of their implications for theory development and their significance for training evaluation and the design of training environments. Limitations and directions to take in future research are discussed.

Network effects: Scale development and implications for new product performance

More and more innovations currently being commercialized exhibit network effects, in other words, the value of using the product increases as more and more people use the same or compatible products. Although this phenomenon has been the subject of much theoretical debate in economics, marketing researchers have been slow to respond to the growing importance of network effects in new product success. Despite an increase in interest in recent years, there is no comprehensive view on the phenomenon and, therefore, there is currently incomplete understanding of the dimensions it incorporates. Furthermore, there is wide dispersion in operationalization, in other words, the measurement of network effects, and currently available approaches have various shortcomings that limit their applicability, especially in marketing research. Consequently, little is known today about how these products fare on the marketplace and how they should be introduced in order to maximize their chances of success. Hence, the motivation for this study was driven by the need to increase our knowledge and understanding of the nature of network effects as a phenomenon, and of their role in the commercial success of new products. This thesis consists of two parts. The first part comprises a theoretical overview of the relevant literature, and presents the conclusions of the entire study. The second part comprises five complementary, empirical research publications. Quantitative research methods and two sets of quantitative data are utilized. The results of the study suggest that there is a need to update both the conceptualization and the operationalization of the phenomenon of network effects. Furthermore, there is a need for an augmented view on customers’ perceived value in the context of network effects, given that the nature of value composition has major implications for the viability of such products in the marketplace. The role of network effects in new product performance is not as straightforward as suggested in the existing theoretical literature. The overwhelming result of this study is that network effects do not directly influence product success, but rather enhance or suppress the influence of product introduction strategies. The major contribution of this study is in conceptualizing the phenomenon of network effects more comprehensively than has been attempted thus far. The study gives an augmented view of the nature of customer value in network markets, which helps in explaining why some products thrive on these markets whereas others never catch on. Second, the study discusses shortcomings in prior literature in the way it has operationalized network effects, suggesting that these limitations can be overcome in the research design. Third, the study provides some much-needed empirical evidence on how network effects, product introduction strategies, and new product performance are associated. In general terms, this thesis adds to our knowledge of how firms can successfully leverage network effects in product commercialization in order to improve market performance.

Frequency-Domain and Wide-Pulse Time-Domain Measurements of Lanthanide Luminescence and Lanthanide-Based Resonance Energy Transfer

Resonance energy transfer (RET) is a non-radiative transfer of the excitation energy from the initially excited luminescent donor to an acceptor. The requirements for the resonance energy transfer are: i) the spectral overlap between the donor emission spectrum and the acceptor absorption spectrum, ii) the close proximity of the donor and the acceptor, and iii) the suitable relative orientations of the donor emission and the acceptor absorption transition dipoles. As a result of the RET process the donor luminescence intensity and the donor lifetime are decreased. If the acceptor is luminescent, a sensitized acceptor emission appears. The rate of RET depends strongly on the donor–acceptor distance (r) and is inversely proportional to r6. The distance dependence of RET is utilized in binding assays. The proximity requirement and the selective detection of the RET-modified emission signal allow homogeneous separation free assays. The term lanthanide-based RET is used when luminescent lanthanide compounds are used as donors. The long luminescence lifetimes, the large Stokes’ shifts and the intense, sharply-spiked emission spectra of the lanthanide donors offer advantages over the conventional organic donor molecules. Both the organic lanthanide chelates and the inorganic up-converting phosphor (UCP) particles have been used as donor labels in the RET based binding assays. In the present work lanthanide luminescence and lanthanide-based resonance energy transfer phenomena were studied. Luminescence lifetime measurements had an essential role in the research. Modular frequency-domain and time-domain luminometers were assembled and used successfully in the lifetime measurements. The frequency-domain luminometer operated in the low frequency domain ( 100 kHz) and utilized a novel dual-phase lock-in detection of the luminescence. One of the studied phenomena was the recently discovered non-overlapping fluorescence resonance energy transfer (nFRET). The studied properties were the distance and temperature dependences of nFRET. The distance dependence was found to deviate from the Förster theory and a clear temperature dependence was observed whereas conventional RET was completely independent of the temperature. Based on the experimental results two thermally activated mechanisms were proposed for the nFRET process. The work with the UCP particles involved the measurement of the luminescence properties of the UCP particles synthesized in our laboratory. The goal of the UCP particle research is to develop UCP donor labels for binding assays. In the present work the effect of the dopant concentrations and the core–shell structure on the total up-conversion luminescence intensity, the red–green emission ratio, and the luminescence lifetime was studied. Also the non-radiative nature of the energy transfer from the UCP particle donors to organic acceptors was demonstrated for the first time in aqueous environment and with a controlled donor–acceptor distance.

Effective diffusivity and convective mass transfer coefficient during the drying of bananas

In this article, a methodology is used for the simultaneous determination of the effective diffusivity and the convective mass transfer coefficient in porous solids, which can be considered as an infinite cylinder during drying. Two models are used for optimization and drying simulation: model 1 (constant volume and diffusivity, with equilibrium boundary condition), and model 2 (constant volume and diffusivity with convective boundary condition). Optimization algorithms based on the inverse method were coupled to the analytical solutions, and these solutions can be adjusted to experimental data of the drying kinetics. An application of optimization methodology was made to describe the drying kinetics of whole bananas, using experimental data available in the literature. The statistical indicators enable to affirm that the solution of diffusion equation with convective boundary condition generates results superior than those with the equilibrium boundary condition.

Water transfer from São Francisco river to semiarid northeast of Brazil: technical data, environmental impacts, survey of opinion about the amount to be transferred

The transposition of the São Francisco River is considered one of the greatest engineering works in Brazil of all time since it will cross an extensive agricultural region of continental dimensions, involving environmental impacts, water, soil, irrigation, water payment and other multidisciplinary themes. Taking into account its importance, this subject was incorporated into a discipline of UFSCar (Federal University of São Carlos - Brazil) named "Pollution and Environmental Impacts". It was noted strong reaction against the project, even before the presentation. To allow a critical analysis, the first objective was to compile the main technical data and environmental impacts. The second objective was to detect the three most important aspects that cause reaction, concluding for the following reasons: assumption that the volume of water to be transferred was much greater than it actually is proposed in the project; lack of knowledge about similar project already done in Brazil; the idea that the artificial canal to be built was much broader than that proposed by the project. The participants' opinion about "volume to be transferred" was raised quantitatively four times: 2-undergraduate students; 1-graduate; 1-outside community. The average resulted 14 times larger than that proposed in the project, significant according to t-test. It was concluded that the reaction to water transfer project is due in part to the ignorance combined with a preconceived idea that tend to overestimate the magnitude of environmental impacts.

Production of a product similar to gelatin from chicken feet collagen

Chicken feet can be used as an alternative source of collagen for the development of new products. In this sense, the aim of this study was the production of a product similar to gelatin from collagen extracted from chicken feet and the evaluation of sensory quality. The products were produced in two distinct flavors, with grape flavor called GU and pineapple flavor called GA. Subsequently, we compared these formulations with gelatin of a trademark established in the market. We used in the verification of sensory acceptability of products a hedonic scale of 9 points and the availability of consuming the product by 30 untrained tasters. According to the results, all formulations showed good levels of acceptability, indicating the collagen from chicken feet as an alternative source of high quality in the production of gelatin.

Effects of Country of Origin on Consumer Product Evaluations: Finnish clothing products in the minds of Russian tourists

Companies operating in today’s highly internationalized markets consider product differentiation the key priority in pursue to attain a constant competitive advantage in challenging global environment (Baker and Ballington 2002, 158). The main driver affecting companies’ differentiation actions was described as early as 1912 by one of the marketing pioneers A. W. Shaw (1912, 710) as meeting human wants more accurate than the competition, and thus increasing customers’ perceived value and satisfaction. Dickson and Ginter (1987, 2) point out in their study based on earlier research by Chamberlin (1965) and Porter (1976) that differentiation can be based on either tangible characteristics of a product such as design or intangible characteristics such as a brand name and country of origin (hereafter referred to as COO). The concept of COO and its impact on consumers’ evaluation of a product as an extrinsic product cue has been one of the most noteworthy topics in international marketing, having been voluminously examined by over 780 authors in more than 750 academic publications in the past 40 years (Papadopoulos and Heslop 2002, 294). Many of these studies accentuate the significant effect the COO has on consumers’ product attribute evaluations. People routinely associate country images with products and services in order to judge and categorize them based on perceived quality and risk levels; thereby COO can influence the likelihood of a purchase (Peterson and Jolibert 1995, 883-884; Verlegh and Steenkamp 1999, 523). Based on the vast research related to COO in the field of international business, it is widely recognized that the country associated with a product can act in a similar way as the name of a brand and even become a part of product’s total image. Thereby depending on customer’s values and perceptions, the product-country image can either increase or decrease perceived value.

Streamlining Launch Support Operations in a Product Platform

The new product development process is a massive investment to a company that aims to reduce their products’ time-to-market. Capability to shorter time-to market allows longer life-cycle to products which are introduced to market earlier but also give advantage to start product launch later while simultaneously learning from customer behavior and competitors. The product launch support operations are the last ramp-up activities before the product launching. This study defines what these operations mean in a product platform and how they can be streamlined to be more efficient. The methodology includes interviews, innovative group brainstorming and regular working group meetings. The challenges concerning the current situation of product launch support operations are allocated into four categories: General, Process, Project Resources and Project Management including altogether ten sub challenges. The challenges include issues related to technology and marketing management, branding strategy, organizing the global platform structure, harmonizing processes and clarifying handovers between shareholders in the process. The study makes a suggestion of a new Product Launch Support organization and clarification of its roles, responsibilities and tasks. In addition a new project management tool and Lessons Learned are suggested to improve the project management. The study can be seen as a pre-study when having an aim at combining technological and marketing know-how in the product ramp-up process before actual production. The future proceedings are suggested to include more detailed specifications and implementation in order to reach the long range target, reduced the time-to-market.

Making Sense of Software Product Requirements

One of the most crucial tasks for a company offering a software product is to decide what new features should be implemented in the product’s forthcoming versions. Yet, existing studies show that this is also a task with which many companies are struggling. This problem has been claimed to be ambiguous and changing. There are better or worse solutions to the problem, but no optimal one. Furthermore, the criteria determining the success of the solution keeps changing due to continuously changing competition, technologies and market needs. This thesis seeks to gain a deeper understanding of the challenges that companies have reportedly faced in determining the requirements for their forthcoming product versions. To this end, product management related activities are explored in seven companies. Following grounded theory approach, the thesis conducts four iterations of data analysis, where each of the iterations goes beyond the previous one. The thesis results in a theory proposal intended to 1) describe the essential characteristics of organizations’ product management challenges, 2) explain the origins of the perceived challenges and 3) suggest strategies to alleviate the perceived challenges. The thesis concludes that current product management approaches are becoming inadequate to deal with challenges that have multiple and conflicting interpretations, different value orientations, unclear goals, contradictions and paradoxes. This inadequacy continues to increase until current beliefs and assumptions about the product management challenges are questioned and a new paradigm for dealing with the challenges is adopted.

A Case Study of Agile Software Engineering Methods and Practices in the MeeGo Harmattan Open Source and Product Context

The aim of this master’s thesis is to study how Agile method (Scrum) and open source software are utilized to produce software for a flagship product in a complex production environment. The empirical case and the used artefacts are taken from the Nokia MeeGo N9 product program, and from the related software program, called as the Harmattan. The single research case is analysed by using a qualitative method. The Grounded Theory principles are utilized, first, to find out all the related concepts from artefacts. Second, these concepts are analysed, and finally categorized to a core category and six supported categories. The result is formulated as the operation of software practices conceivable in circumstances, where the accountable software development teams and related context accepts a open source software nature as a part of business vision and the whole organization supports the Agile methods.

Worker motivation in crowdsourcing new product development

In the study the recently appeared technology of crowdsourcing and its implications to new product development activities. The goal of the research is to figure out the motivating factors used in crowdsourcing projects related to new product development. The study is based on the theoretical backgrounds of crowdsourcing; new product development, and motivation, which resulted in the framework for the crowdsourcing cases assessment and the list of possible motivating factors used for the analysis. The research is based on 16 crowdsourcing projects divided in 4 sets according to the stage of new product development at which they are directed. The motivating factors present in the projects were distinguished and explained. Further analysis allowed making conclusions showing which of the motivating factors are suitable for the crowdsourcing projects related to the particular stage of new product development. The results can be used for creation or assessment of crowdsourcing projects for the companies because the main factor of success for crowdsourcing is motivation, and the work is answering how to motivate the workers.

Improving product profitability control in continuous IT-services

The target of the thesis is to improve product profitability control in continuous IT-services. Accurate product cost accounting and correctly allocated revenues are a necessity for good product profitability control. The focus of the study is on costs and revenues that are not traced directly to services. The thesis is focused on revenue allocations as revenue allocation methods have not been used in the case company before. In order to achieve the target revenue allocation methods, which improve the product profitability accounting and control, are presented. The research methods used in the thesis are literature review and empirical case study. The research approach is constructive. The theoretical part is composed of literature and articles that create a base for the empirical part. Internal interviews describe the current situation in the company and based on it development actions are planned. The part of the empirical case study is seen mostly in the limitations as the research is limited to concern only one department in the company. Problems in the revenue tracing are caused by customer specific services and lack of service definitions because of which the revenues are not traced correctly. Methods to allocate revenues are presented in the thesis and stand-alone revenue allocation method is the most suitable one because it is fair and it can be modified. Approximate product profitability analysis is done in the thesis and the results of it indicate that some services are profitable and some unprofitable.

Intra-organizational knowledge transfer in a Finnish multinational company

The ability of a multinational company to effectively transfer knowledge from one unit to another can create a great source of competitive advantage and is crucial for long-term success. However, in their attempts to disseminate existent knowledge across national boundaries, organizations encounter several obstacles. Especially challenging is the transfer of tacit knowledge, the most valuable kind, as it is embedded in the minds and the behavior of people. The purpose of this study is to identify the main factors and challenges to be considered in intra-organizational knowledge transfer and consequently develop a framework that could be utilized to improve the process. The research is of qualitative nature and it adopts an exploratory approach. The study was further conducted as an intensive single-case study through studying a Finnish multinational company, and the researcher adopted a role as a participant observant in the research setting. Other data collection methods include semi-structured interviews and an online survey. The research findings show that knowledge transfer is currently challenging within the international sales organization of the case company. The majority of knowledge is currently concentrated in the company headquarters, and it is not always systematically distributed to the regional offices abroad. The main factor affecting knowledge transfer seems to be the organizational culture, which does not support or encourage knowledge sharing. The company is struggling in having a common place for information and employees that lack proper social networks have difficulties accessing relevant knowledge. Some recommended improvement suggestions include the institutionalization of knowledge transfer by turning it into an articulated organizational goal, and the implementation of a reward system that includes soft factors, such as teamwork and knowledge sharing behavior. Furthermore, the organizational culture should be more open and supportive in order to reinforce trust. Individuals in regional offices should be given better support by offering them dedicated mentors and increasing the amount of expatriation. Finally, knowledge should actively be codified and stored in commonly shared platforms where it is easily accessible by all employees.