PROPERTIES OF ZNS THIN-FILMS PREPARED BY 248-NM PULSED-LASER DEPOSITION

Pulsed laser deposition (PLD) from a hot pressed manganese doped ZnS target using a KrF laser, has produced a high rate deposition method for growing luminescent thin films. Good stoichiometric quality and typical luminescent crystal structures have been observed with a predominant hexagonal phase and little evidence of the cubic phase. The luminescent characteristics were determined by cathodoluminescence and photoluminescence excitation and stable electroluminescence was observed under pulsed dc conditions with a minimum brightness of 150 cd/m2. PLD film characteristics are compared with those observed in radio-frequency sputtered samples.

Hybrid FIB milling strategy for the fabrication of plasmonic nanostructures on semiconductor substrates

The optical properties of plasmonic semiconductor devices fabricated by focused ion beam (FIB) milling deteriorate because of the amorphisation of the semiconductor substrate. This study explores the effects of combining traditional 30 kV FIB milling with 5 kV FIB patterning to minimise the semiconductor damage and at the same time maintain high spatial resolution. The use of reduced acceleration voltages is shown to reduce the damage from higher energy ions on the example of fabrication of plasmonic crystals on semiconductor substrates leading to 7-fold increase in transmission. This effect is important for focused-ion beam fabrication of plasmonic structures integrated with photodetectors, light-emitting diodes and semiconductor lasers.

Plasmonic junctions with cucurbit[5]uril 'glue': fabrication of precise sub-nm junctions in gold nanoparticle assemblies

Aggregation of gold nanoparticles with rigid cucurbit[5]uril molecules generates fixed inter-particle separations of 0.91 nm. These nanoparticle assemblies possess discrete plasmonic modes which elucidate nanoscale growth and serve as molecular-recognition based SERS substrates.

Piezoresponse force microscopy of ferroelectric thin films: Frequency dependence of phase imaging

The objective of this work is an evaluation of quantitative measurements of piezoresponse force microscopy for nanoscale characterization of ferroelectric films. To this end, we investigate how the piezoresponse phase difference Delta Phi between c domains depends on the frequency omega of the applied ac field much lower than the cantilever first resonance frequency. The main specimen under study was a 102 nm thick film of Pb(Zr(0.2)Ti(0.8))O(3). For the sake of comparison, a 100 nm thick PbTiO(3) film was also used. From our measurements, we conclude a frequency dependent behavior Delta Phi similar to omega(-1), which can only be partially explained by the presence of adsorbates on the surface. (C) 2008 American Institute of Physics.

Application of surface plasmon polaritons in the laser ablation and characterisation of thin aluminium films

Surface modification of thin aluminium films is both produced and characterised by exciting surface plasmon polaritons in an attenuated total reflection geometry: silica prism/aluminium/aluminium oxide system. The modification is performed, under ambient conditions, by exposure to a low fluence (

SURFACE-PLASMON ENHANCED LASER-ABLATION OF THIN METAL-FILMS

Surface plasmon enhancement of laser ablation of thin Al films is examined with a view to its application in metal film patterning and nano-structuring. Al films, deposited on silica prisms, are first characterized by attenuated total reflection using a broadband UV source and appropriate interference filter. The films are subsequently subjected to excimer laser radiation of wavelength 248 nm under conditions both of direct incidence from the air side of the film, and of surface plasmon excitation in which light is incident through the prism at greater than critical angle. For a given level of ablation damage in a particular film the fluence required using the surface plasmon technique is 3-5 times less than that needed when direct incidence is used. This is roughly in line with the energy absorbed in the film. From a practical standpoint it is clear that ablation of metal films can be achieved with much lower fluences than has hitherto been possible, thus reducing the requirements on laser output and relaxing the power handling constraints on any input optical elements.

Rapid, simple method for determining the porosity of mesoporous TiO2 films using a quartz crystal microbalance (QCM)

Two different mesoporous films of TiO2 were coated onto a QCM disc and fired at 450o C for 30 min. The first film was derived from a sol-gel paste that was popular in the early days of dye-sensitised solar cell, i.e. dssc, research, a TiO2(sg) film. The other was a commercial colloidal paste used to make examples of the current dssc cell; a TiO2(ds) film. A QCM was used to determine the mass of the TiO2 film deposited on each disc and the increase in the mass of the film when immersed in water/glycerol solutions with wt% values spanning the range 0-70%. The results of this work reveal that with both TiO2 mesoporous films the solution fills the film's pores and acts as a rigid mass, thereby allowing the porosity of each film to be calculated as: 59.1% and 71.6% for the TiO2(sg) and TiO2(ds) films, respectively. These results, coupled with surface area data, allowed the pore radii of the two films to be calculated as: 9.6 and 17.8 nm, respectively. This method is then simplified further, to just a few frequency measurements in water and only air to reveal the same porosity values. The value of the latter ‘one point’ method for making porosity measurements is discussed briefly.

Development of chitosan packaging films with carvacrol and grape seed extract as antimicrobial and antioxidant agents

In order to produce packaging films with a broad spectrum of action on microorganisms, the effect of two antimicrobial (AM) to be included in the films, carvacrol and GSE were studied separately on different microorganisms. Carvacrol was more effective against the grampositive bacteria than against the gram-negative bacterium. GSE was not effective against yeast. Subsequently, a search for optimal combinations of carvacrol, GSE and the addition of chitosan (as a third component with film forming properties) was carried out. Response surface analysis showed several synergetic effects and three optimal AM combinations (OAMC) were obtained for each microorganism. The experimental validation confirmed that the optimal solutions found can successfully predict the response for each microorganism. The optimization of mixtures of the three components, but this time, using the same concentration for all microorganisms, was also studied to obtain an OAMC with wide spectrum of activity. The results of the response surface analysis showed several synergistic effects for all microorganisms. Three OAMC, OAMC-1, OAMC-2, OAMC-3, were found to be the optimal mixtures for all microorganisms. The radical scavenging activity (RSA) of the different agents was then compared with a standard antioxidant (AOX) BHT, at different concentrations; as also at the OAMC. The RSA increased in the following order: chitosanof OAMC-3. The physico-mechanical properties of 3 films, film-1 with OAMC-1, film-2 with OAMC-2 and film-3 with OAMC-3 were studied. Film-3 presented the lowest WVP, CO2P and TS values and the highest O2P whereas film-1 presented the highest WVP and the lowest crystallinity, CO2P, TS and luminosity. Being one of the components of GSE, gallic acid (GA) release in water from film-1, film-2 and film-3 was next studied over a 30 day period. The mathematical model for the release of GA based on Fick’s law successfully fitted the experimental data and GA diffusion coefficients, assumed to be Arrhenius temperature dependent were obtained for each film. This work will contribute to the development of environmentally friendly packaging films, resulting in improved food preservation and shelf-life extension.