Nanocrystalline SnO2-based, UVB-activated, colourimetric oxygen indicator

Nanocrystalline SnO2, ncSnO(2), is used as a photosensitiser in a colourimetric O-2 indicator that comprises a sacrificial electron donor, glycerol, a redox dye, methylene blue (MB), and an encapsulating polymer, hydroxyethyl cellulose (HEC). Upon exposure to a burst of UVB light the indicator is activated (photo-bleached) as the MB is photoreduced by the ncSnO(2) particles. In the absence of oxygen, the film stays bleached, but recovers its original colour upon exposure to oxygen. Unlike its TiO2-based predecessor, the HEC/glycerol/MB/ncSnO(2) O-2 indicator is not activated by UVA light from white fluorescent lamps, but is by UVB light. This feature provides much greater control in the activation of the indicator. Other work shows the rate of activation depends upon I-0.75, where I is the UVB irradiance, indicating a partial dependence upon the electron-hole recombination process. The half-life of the recovery of the original colour of a UV-activated film, t(50), is directly proportional to the ambient level of oxygen. The advantages of using this indicator in modified atmosphere packaging as a possible quality assurance indicator are discussed briefly. (c) 2008 Elsevier B.V. All rights reserved.

Photocatalytic oxidation of deposited sulfur and gaseous sulfur dioxide by TiO2 films

Thick (4 mu m) films of anatase titania are used to photocatalyze the removal of deposited films of amorphous sulfur, similar to 2.8 mu m, thick and under moderate illumination conditions (I = 5.6 mW cm(-2)) on the open bench the process is complete within similar to 8 or 18 h using UVC or UVA light, respectively. Using UVA light, 96% of the product of the photocatalytic removal of the film of sulfur is sulfur dioxide, SO2. The photonic efficiency of this process is similar to 0.16%, which is much higher (> 15 times) than that of the removal of soot by the same films, under similar experimental conditions. In contrast to the open bench work, in a closed system the photocatalytic activity of a titania film toward the removal of sulfur decreased with repeated use, due to the accumulation of sulfuric acid on its surface generated by the subsequent photocatalytic oxidation of the initial product, SO2. The H2SO4-inactivated films are regenerated by soaking in water. The problems of using titania films to remove SO2 from a gaseous environment are discussed briefly.

Photochemical reduction of oxygen adsorbed to nanocrystalline TiO2 films: A transient absorption and oxygen scavenging study of different TiO2 preparations

Transient absorption spectroscopy (TAS) has been used to study the interfacial electron-transfer reaction between photogenerated electrons in nanocrystalline titanium dioxide (TiO2) films and molecular oxygen. TiO2 films from three different starting materials (TiO2 anatase colloidal paste and commercial anatase/rutile powders Degussa TiO2 P25 and VP TiO2 P90) have been investigated in the presence of ethanol as a hole scavenger. Separate investigations on the photocatalytic oxygen consumption by the films have also been performed with an oxygen membrane polarographic detector. Results show that a correlation exists between the electron dynamics of oxygen consumption observed by TAS and the rate of oxygen consumption through the photocatalytic process. The highest activity and the fastest oxygen reduction dynamics were observed with films fabricated from anatase TiO2 colloidal paste. The use of TAS as a tool for the prediction of the photocatalytic activities of the materials is discussed. TAS studies indicate that the rate of reduction of molecular oxygen is limited by interfacial electron-transfer kinetics rather than by the electron trapping/detrapping dynamics within the TiO2 particles.

The photo-oxidation of water by sodium persulfate, and other electron acceptors, sensitised by TiO2

A number of different electron acceptors are tested for efficacy in the oxidation of water to oxygen, photocatalysed by titanium dioxide. The highly UV-absorbing metal ion electron acceptors, Ce4+ and Fe3+, appear ineffective at high concentration (10(-2) M), due to UV-screening, but more effective at lower concentrations (10(-3) M). The metal-depositing electron acceptor, Ag+, is initially effective, but loses activity upon prolonged irradiation due to metal deposition which promotes electron-hole recombination as well as UV-screening the titania particles. Most striking of the electron acceptors tested is persulfate, particularly in alkaline solution (0.1 M NaOH). The kinetics of the photo-oxidation of water by persulfate, photocatalysed by titania are studied as a function of pH, [S2O82-] and incident light intensity (I). The initial rate of water oxidation increases with pH, is directly proportional to the concentration of persulfate present and depends upon I-0.6. The TiO2/alkaline persulfate photosystem is robust and shows very little evidence of photochemical wear upon repeated irradiation. The results of this work are discussed with regard to previous work in this area and current mechanistic thinking. The formal quantum efficiency of the TiO2/alkaline persulfate photosystem was estimated as ca. 2%. (C) 2004 Elsevier B.V. All rights reserved.

The alteration of the structural properties and photocatalytic activity of TiO2 following exposure to non-linear irradiation sources

When TiO2 powder was irradiated with a laser light (>0.8 MW peak pulse power (PPP) at 355 nm) a visible change in its colour from white to dark blue was observed. The initial rate of change of the total colour difference was related to the laser light intensity and the longer the irradiation time the more substantial the colour change. The result of X-ray diffraction (XRD) studies showed that the crystal structure of the TiO2 developed a more rutile form after laser exposure. ESR studies indicated that the colour change was associated with the generation of Ti(III) species in the photocatalyst. Electron microscopic studies showed that more spherical shaped particles of TiO2 were observed after laser treatment although the average particle size remained largely unchanged. No significant changes in the band gap or the surface area of the laser modified TiO2 were observed. The laser modified photocatalyst showed no enhancement in activity for the destruction of methylene blue, rhodamine B and stearic acids, indicating that the rutile/anatase ratio is unimportant in the destruction of the test pollutants used in this work, via TiO2 photocatalysis

Novel TiO2 CVD films for semiconductor photocatalysis

A novel CVD film of titanium(IV) oxide has been prepared on glass, via the reaction of titanium(IV) chloride and ethyl acetate, using a CVD technique. The film is clear, very robust mechanically and comprised of a thin (24 nm) layer of nanocrystalline anatase titania that absorbs light of lambda

Anodic stripping voltammetry with photochemical preconcentration at nanocrystalline TiO2 films: Detection of Ag+ and Hg2+

Nanocrystalline TiO2 deposited on conducting glass plates is shown to be an excellent material for preconcentration of silver and mercury, via photochemical reaction, prior to their detection by anodic stripping voltammetry (ASV). During the first stage of growth in the photoreduction of silver or mercury, 3D nuclei are formed on the TiO2 film. As the deposition proceeds micrometer size agglomerates grow on the surface. The conical morphology of the silver nuclei grown on a (110) rutile single crystal in the initial stages of growth suggests that there is a preferential deposition of silver at the centre of the growing nuclei. When the nuclei size reach a critical value (ca. 400 nm diameter, 40 nm height) the morphology changes to a globular shape without any preferential site for deposition on the surface of the silver nucleus. It was observed that micromolar concentrations of silver or mercury can be detected by anodic stripping voltammetry and relatively large amounts of these metals (micrometer scale nuclei) can be loaded on the nanocrystalline TiO2 film surface. The latter opens the possibility of analytical applications of nanocrystalline TiO2 electrodes for the selective detection of silver or mercury via photochemical anodic stripping voltammetry.

The kinetics of semiconductor photocatalysis: Light intensity effects

The kinetics of the photomineralisation of 4-chlorophenol, 4-CP, by oxygen, sensitized by TiO2 as a function of incident light intensity are described. Degussa P25 TiO2 in the form of either a thin film or a dispersion is used as the photocatalyst. With a TiO2 dispersion the initial rate of photomineralisation, R-i, depends upon I-0.64, implying that electron-hole recombination is the dominant process with respect to photogenerated holes (where R-i is expected proportional to I-0.5), but that the light intensities used spanned both the high (R-i expected proportional to I-0.5) and low (R-i expected proportional to I) intensity regimes. With a TiO2 film R-i is proportional to I indicating that the photocatalytically active particles of the TiO2 film are shielded in some way and so operate under low intensity conditions. Most significantly, it was also found that the apparent value of the Langmuir adsorption coefficient, K4-CP, as determined from the kinetic data, was not independent of I for either a TiO2, film or dispersion photocatalyst. Rather K4-CP increased with decreasing light intensity. A possible mechanism is suggested as a rationale for the observed light intensity effects reported.

Photobleaching of methylene blue sensitised by TiO2: an ambiguous system?

The photobleaching of methylene blue MB, sensitised by TiO2, in an aqueous solution is studied in the absence and presence of oxygen, in the absence of oxygen and in the presence of a sacrificial electron acceptor (SED), MB is photoreduced to its colourless leuco form, LMB, by the TiO2 photocatalyst. This same photoreduction process is observed even if an SED is not present, indicating that MB itself can act as an SED. The oxidation of LMB by oxygen to regenerate MB is significantly slower if the aqueous solution is acidified (0.01 mol dm(-3) HClO4) and, at low partial pressures, the rate of reaction depends directly upon the concentration of dissolved oxygen. The TiO2-sensitised photobleaching of MB is irreversible in an oxygen-saturated aqueous solution, as expected, since the bleaching was due to an oxidative process. However, in an acidified solution (0.01 mol dm(-3) HClO4), the photobleaching process, in an oxygen-saturated solution, generates LMB initially. The latter situation arises because, under acidic conditions, LMB reacts only very slowly with oxygen to form MB. The significance of these findings with respect to the popular use of photobleaching of MB as a demonstration of semiconductor photomineralisation is discussed. (C) 1999 Elsevier Science S.A. All rights reserved.

Modification and enhanced photocatalytic activity of TiO2 following exposure to non-linear irradiation sources

The effects of high power pulsed laser light on a TiO2 photocatalyst (powder and 0.1% (w/v) aqueous suspension) are reported. When this material was irradiated with a laser of power over 0.8 MW peak pulse power at 355 nm wavelength a visible change in colour from white to dark blue was observed. The initial rate of change of the total colour difference is related to the laser power; the stronger the laser power the darker the colour change. The result of X-ray diffraction studies indicates that the crystal structure of the TiO2 developed a more rutile form after laser exposure. Electron microscopic studies showed that spherical shaped particles of TiO2 were observed after laser treatment. Preliminary results show enhanced photocatalytic activity for the destruction of methylene blue. (C) 1999 Elsevier Science S.A. All rights reserved.

Photomineralisation of 4-chlorophenol sensitised by TiO2 thin films

The results of a study of the oxidative mineralisation of 4-CP by oxygen, sensitised by thin films of Degussa P25 TiO2, are reported. The films are used under conditions in which the kinetics of photomineralisation are independent of mass transfer effects and stable towards repeated irradiation. Using a TiO2 film, the process goes through the same mechanism as a TiO2 dispersion, generating the same intermediates, namely: 4-chlorocatechol and hydroquinone. The kinetics of photomineralisation show clear differences between a TiO2 film and a dispersion. With TiO2 films the initial rate of photomineralisation is strongly dependent upon photocatalyst loading, (units; g dm(-3)) reaching a distinct maximum, which appears to be associated with the formation of a monolayer of aggregated particles - the diameter of the aggregated particles is estimated as 0.44 mu m. A simple 2D model is presented to help illustrate the features of such a system. With TiO2 dispersions the rate usually reaches a plateau at ca. 0.5 g dm(-3) of TiO2. For TiO2 films the initial rate depends directly upon the incident light intensity, implying that the photocatalytically active particles are under low illumination conditions, partially shielded by the other particles making up each aggregated particle. In contrast, with TiO2 dispersions R-i depends upon I-0.64, implying that the different light intensities used spanned both the high (R(i)proportional to I-1/2) and low (R(i)proportional to I) intensity kinetic regions. The kinetics of photomineralisation of 4-CP, sensitised by TiO2 films obey the same Langmuir-Hinshelwood expressions as found in most semiconductor photocatalyst work conducted with TiO2 dispersions. However, in a study of the variation R-i as a function of [4-CP] and [O-2] the values for the maximum rates were larger, and those for the apparent Langmuir adsorption coefficients were smaller, than those found for TiO2 dispersions. (C) 1998 Elsevier Science S.A. All rights reserved.

ACID ENHANCEMENT EFFECT IN THE CLEAN OXIDATION OF TOLUENES PHOTOCATALYZED BY TIO2

The yield of substituted benzaldehydes and benzoic acids formed by the aerial oxidation of a range of substituted toluenes photocatalysed by titanium dioxide in acetonitrile is dramatically improved by the addition of small amounts of sulfuric acid.

EFFECT OF PH ON THE STABILITY OF TIO2 COATINGS ON GLASS PHOTOCATALYSIS REACTORS FOR WATER-PURIFICATION

TiO2 coated glass shows excellent stability in the range pH 2-9, however, there is rapid and complete stripping of the TiO2 coating between pH 11 and 12.

PHOTOMINERALIZATION OF SALICYLIC-ACID - A KINETIC-STUDY

The kinetics of the photomineralization of salicylic acid (SA) sensitized by Degussa P25 titanium dioxide (TiO2) dispersions in oxygenated aqueous solution are reported as a function of the following experimental parameters: [TiO2], percentage of O-2, [SA], temperature (T) and light intensity (I). The kinetics of SA photomineralization conform to a Langmuir-Hinshelwood kinetic scheme with SA and O-2 adsorbed at different sites with apparent Langmuir adsorption coefficients of (6.1 +/- 1.2) x 10(4) mol(-1) dm(3) and 0.061 +/- 0.007 kPa(-1) respectively. The overall activation energy for the system was determined as 4.6 +/- 0.2 kJ mol(-1). Two major stable reaction intermediates are identified (dihydroxybenzoic acids (DHBA) and catechol (C)) and the existence of a further pathway involving one or more very unstable and, as yet, unidentified reaction intermediates is proposed. A kinetic model is presented which describes the temporal behaviour of the concentrations of SA, CO2 and the major photogenerated intermediates (DHBA and C). This model is used to predict successfully the temporal behaviour of the major intermediates in the photomineralization of SA under non-standard conditions.

WATER-PURIFICATION BY SEMICONDUCTOR PHOTOCATALYSIS

The basic principles of the photooxidative mineralization of organic pollutants by O2, sensitized by TiO2, are described. The kinetics of this process as a function of [TiO2], [organic pollutant], [O2], light intensity, temperature, pH, and the type of anion present are discussed, and a general kinetic model is presented. Standard test and demonstration systems for water purification by TiO2 photocatalysis are described and other novel applications of semiconductor photocatalysis are outlined.