Monitoring and model updating of an FRP pedestrian truss bridge

This paper presents the results of a real bridge field experiment, carried out on a fiber reinforced polymer (FRP) pedestrian truss bridge of which nodes are reinforced with stainless steel plates. The aim of this paper is to identify the dynamic parameters of this bridge by using both conventional techniques and a model updating algorithm. In the field experiment, the bridge was instrumented with accelerometers at a number of locations on the bridge deck, recording both vertical and transverse vibrations. It was excited via jump tests at particular locations along its span and the resulting acceleration signals are used to identify dynamic parameters, such as the bridge mode shape, natural frequency and damping constant. Pedestrianinduced vibrations are also measured and utilized to identify dynamic parameters of the bridge. For a complete analysis of the bridge, a numerical model of the FRP bridge is created whose properties are calibrated utilizing a model updating algorithm. Comparable frequencies and mode shapes to those from the experiment were obtained by the FE models considering the reinforcement by increasing elastic modulus at every node of the bridge by stainless steel plate. Moreover, considering boundary conditions at both ends as fixed in the model resulted in modal properties comparable/similar to those from the experiment. This study also demonstrated that the effect of reinforcement and boundary conditions must be properly considered in an FE model to analyze real behavior of the FRP bridge.

Monosyllabic Circumflexion in Lithuanian

This PhD thesis examines a phenomenon known as Monosyllabic Circumflexion (MC, hereafter) from a historical linguistics / phonological point of view. MC denotes a Lithuanian or Balto-Slavic phenomenon according to which long vowels and diphthongs in monosyllabic words exhibit a circumflex tone instead of the expected acute tone.  It is observed in the following four categories: I. 3rd person future forms of monosyllabic stems (e.g., šõks ― šókti `to jump;' vy͂s ― výti `to drive') II. reflexes of PIE root nouns (e.g., Latv. gùovs `cow;' Lith. šuõ `dog') III. prepositions/adverbs (e.g., nuõ `from' ~  nùotaka `bride;' vė͂l `again' ~ Latv. vêl `still, yet,' tė͂ (permissive particle) < *teh1) IV. pronominal forms (e.g., tuõ ~ gerúoju `the good (m.~sg.~instr.),' tie͂ ~ tíeji `id. (pl.nom)'). The unexpected circumflex tone in these categories is problematic and important for the solution of a Balto-Slavic accentological question on the etymological background of acute and non-acute tones. The aim of this thesis is to partially contribute to the solution of this problem by establishing the existence of MC and its relative chronology. The first category, the 3rd person future forms, provides a substantial number of examples and counterexamples. The examination of them has revealed the fact that the counterexamples constitute a morpho-semantic group of verbs whose future stems underwent considerable morphological changes in the prehistory, hence not exhibiting MC. This shows that the regular tonal reflex of the 3rd person future forms of monosyllabic acute stem must be circumflex, allowing for the establishment of MC as a regular phonological process, although this category does not provide much information on the relative chronology of MC. The second category, the reflexes of Proto-Indo-European root nouns, gives an important clue as to where MC is located in the relative chronology of Balto-Slavic sound changes. Next, there is a discussion of whether the results of the examinations of the first two categories can be maintained for the data of the third and fourth categories, which show an irregular distribution of the acute and circumflex tones in monosyllabic forms. It is shown that various morphological factors, such as homonymic clashes within the paradigms for pronouns, can explain why some monosyllabic forms have acute tone. Also, the linguistic feature of West Aukštaitian dialects of Lithuanian that tend to preserve the results of MC is revealed. These dialects are known to have played an important role in the formation of standard Lithuanian. In this way, the monosyllabic forms with unexpected circumflex tone in Lithuanian are explained as a combination of MC in the Proto-Balto-Slavic time and the dialectal tendency of West Aukštaitian dialects of Lithuanian.

Oförändrad prestation, men varierande motivation under menstruationscykeln : Ett examensarbete som undersöker om maximalstyrka och explosivitet förändras under menstruationscykeln samt om motivationen korrelerar med prestationen

Syfte - Studien avser att undersöka om prestation gällande maximalstyrka och explosivitet varierar under menstruationscykeln. Dessutom undersöks om den psykologiska motivationen eller känslan korrelerar med prestationen. Studiens syfte är att skapa en utgångspunkt för att se om periodisering av styrketräning i relation till menstruationscykeln faser är aktuell för kvinnor inom prestationsidrotter. Metod - Testerna genomfördes under en menstruationscykel, fyra veckor. Ett test genomfördes varje vecka för att täcka in fyra faser under menstruationscykeln och för att erhålla ett konsekvent veckomönster. Menstruationscykelns faser räknades ut i efterhand för att inte i förhand påverka testdeltagarnas motivation och prestation i förhållande till menstruationscykeln. Fas 1 menstruationsfas, fas 2 intermenstruation, fas 3 intermenstruation/ägglossning och fas 4 premenstruation. I testgruppen ingick fyra kvinnor, 32 år (± 10), längd 162,8 cm (± 7,32), vikt 57,4 kg (± 5,79). I kontrollgruppen ingick en man och två kvinnor utan menstruation, 26,67 år (± 9,02), längd 168,3 cm (± 8,96), vikt 71,7 kg (± 11,02). Fysiska tester, längdhopp och knäböj. En standardiserad uppvärmning genomfördes inför varje test, följdes av tre stycken jämfota längdhopp utan ansats med två minuter vila mellan hoppen. Bästa hoppet av tre dokumenterades. Längdhopp (CV 1,8 %) (Hopkins, Schabort & Hawley, 2001), knäböj, en repetition max [1RM] (CV 1,57 %) (Urquhart, Moir, Graham & Connaboy, 2015). En specifik uppvärmning genomfördes även inför 1RM knäböj därefter försök på en repetition på 1RM. Frågeformulär gällande hälsotillstånd och motivation “Snabbkollen” (Cross & Lyle, 1999) besvarades inför varje testtillfälle. Vid sista testtillfället fick alla testdeltagare fylla i ett frågeformulär om upplevda symptom och tillstånd under den gångna menstruationscykeln. Resultat och slutsats - Det är ur denna studie svårt att tyda om menstruationscykelns olika faser skulle ha någon relevant effekt värd att ta hänsyn till när det gäller prestationen hos idrottande kvinnor. Dock visar resultaten att menstruationscykeln påverkar motivationen.  

“Art Will Not Disappear Into Nothing; It Will Disappear Into Everything“: The Black Audio Film Collective and Latin America

The development of Latin American cinema in the 1960s was underwritten by a number of key texts that outlined the aesthetic and political direction of individual filmmakers and collectives (Solanas and Getino, 1969; Rocha, 1965; Espinosa, 1969). Although asserting the specificity of Latin American culture, the theoretical foundations of its New Wave influenced oppositional filmmaking way beyond its own regional boundaries. This chapter looks at how movements in British art cinema, especially the Black Audio Film Collective, were inspired and propelled by the theories behind New Latin American cinema. Facilitated by English translations in journals such as Jump Cut in the early ‘80s, Cuban and Argentine cinematic manifestoes provided a radical alternative to the traditional language of film theory available to filmmakers in Europe and works such as Signs of Empire (1983-4); Handsworth Songs (1986) and Seven Songs for Malcolm X (1993) grew out of this trans-continental exchange. The Black Audio Film Collective represented a merging of politics, popular culture, and art that was, at once, oppositional and melodic. Fusing postcolonial discourse with pop music, the avant-garde and re-imaginings of subalternity, the work of ‘The Collective’ provides us with a useful example of how British art cinema has drawn from theoretical foundations formed outside of Europe and the West. As this chapter will argue however, the Black Audio Film Collective’s work can also be read as a reaction to the specificity of British socio-politics of the ‘80s and ‘90s. Its engagement with the aesthetico-political strategies of Latin American cinema, then, undercut what was a solidly British project, rooted in (post)colonial history and emerging ideas of disaporic identity. If the propulsive thrust of The Black Audio Film Collective’s art was shaped by Third Cinema, its images and concerns were self-consciously British.

Proprioception in ankle sprain from exercises and bandages

Ankle sprains are the most common injuries in sports, usually causing damage to the lateral ligaments. Recurrence has as usual result permanent instability, and thus loss of proprioception. This fact, together with residual symptoms, is what is known as chronic ankle instability, CAI, or FAI, if it is functional. This problem tries to be solved by improving musculoskeletal stability and proprioception by the application of bandages and performing exercises. The aim of this study has been to review articles (meta-analisis, systematic reviews and revisions) published in 2009-2015 in PubMed, Medline, ENFISPO and BUCea, using keywords such as “sprain instability”, “sprain proprioception”, “chronic ankle instability”. Evidence affirms that there does exist decreased proprioception in patients who suffer from CAI. Rehabilitation exercise regimen is indicated as a treatment because it generates a subjective improvement reported by the patient, and the application of bandages works like a sprain prevention method limiting the range of motion, reducing joint instability and increasing confidence during exercise. As podiatrists we should recommend proprioception exercises to all athletes in a preventive way, and those with CAI or FAI, as a rehabilitation programme, together with the application of bandages. However, further studies should be generated focusing on ways of improving proprioception, and on the exercise patterns that provide the maximum benefit.

Aerobic and anaerobic test performance among elite male football players in different team positions

The purpose was to determine the magnitude of aerobic and anaerobic performance factors among elite male football players in different team positions. Thirty-nine players from the highest Swedish division classified as defenders (n=18), midfield players (n=12) or attackers (n=9) participated. Their mean (± sd) age, height and body mass (bm) were 24.4 (±4.7) years, 1.80 (±5.9)m and 79 (±7.6)kg, respectively. Running economy (RE) and anaerobic threshold (AT) was determined at 10, 12, 14, and 16km/h followed by tests of maximal oxygen uptake (VO2max). Maximal strength (1RM) and average power output (AP) was performed in squat lifting. Squat jump (SJ), counter-movement jump with free arm swing (CMJa), 45m maximal sprint and the Wingate test was performed. Average VO2max for the whole population (WP) was 57.0mL O2•kg-1min-1 . The average AT occurred at about 84% of VO2max. 1RM per kg bm0.67 was 11.9±1.3kg. Average squat power in the whole population at 40% 1RM was 70±9.5W per kg bm0.67 . SJ and CMJa were 38.6±3.8cm and 48.9±4.4cm, respectively. The average sprint time (45m) was 5.78± 0.16s. The AP in the Wingate test was 10.6±0.9W•kg-1 . The average maximal oxygen uptake among players in the highest Swedish division was lower compared to international elite players but the Swedish players were better off concerning the anaerobic threshold and in the anaerobic tests. No significant differences were revealed between defenders, midfielders or attackers concerning the tested parameters presented above.

Aerobic and anaerobic test performance among elite male football players in different team positions

The purpose was to determine the magnitude of aerobic and anaerobic performance factors among elite male football players in different team positions. Thirty-nine players from the highest Swedish division classified as defenders (n=18), midfield players (n=12) or attackers (n=9) participated. Their mean (± sd) age, height and body mass (bm) were 24.4 (±4.7) years, 1.80 (±5.9)m and 79 (±7.6)kg, respectively. Running economy (RE) and anaerobic threshold (AT) was determined at 10, 12, 14, and 16km/h followed by tests of maximal oxygen uptake (VO2max). Maximal strength (1RM) and average power output (AP) was performed in squat lifting. Squat jump (SJ), counter-movement jump with free arm swing (CMJa), 45m maximal sprint and the Wingate test was performed. Average VO2max for the whole population (WP) was 57.0mL O2•kg-1min-1. The average AT occurred at about 84% of VO2max. 1RM per kg bm0.67 was 11.9±1.3kg. Average squat power in the whole population at 40% 1RM was70±9.5W per kg bm0.67. SJ and CMJa were 38.6±3.8cm and 48.9±4.4cm,respectively. The average sprint time (45m) was 5.78± 0.16s. The AP in the Wingate test was 10.6±0.9W•kg-1. The average maximal oxygen uptake among players in the highest Swedish division was lower compared to international elite players but the Swedish players were better off concerning the anaerobic threshold and in the anaerobic tests. No significant differences were revealed between defenders, midfielders or attackers concerning the tested parameters presented above.

How do Small Players Deduce Beliefs about Uncertainty? A Look at Texas Shale Oil Investments

Thesis (Ph.D.)--University of Washington, 2016-08

Bayesian nonparametric latent variable models

L’un des problèmes importants en apprentissage automatique est de déterminer la complexité du modèle à apprendre. Une trop grande complexité mène au surapprentissage, ce qui correspond à trouver des structures qui n’existent pas réellement dans les données, tandis qu’une trop faible complexité mène au sous-apprentissage, c’est-à-dire que l’expressivité du modèle est insuffisante pour capturer l’ensemble des structures présentes dans les données. Pour certains modèles probabilistes, la complexité du modèle se traduit par l’introduction d’une ou plusieurs variables cachées dont le rôle est d’expliquer le processus génératif des données. Il existe diverses approches permettant d’identifier le nombre approprié de variables cachées d’un modèle. Cette thèse s’intéresse aux méthodes Bayésiennes nonparamétriques permettant de déterminer le nombre de variables cachées à utiliser ainsi que leur dimensionnalité. La popularisation des statistiques Bayésiennes nonparamétriques au sein de la communauté de l’apprentissage automatique est assez récente. Leur principal attrait vient du fait qu’elles offrent des modèles hautement flexibles et dont la complexité s’ajuste proportionnellement à la quantité de données disponibles. Au cours des dernières années, la recherche sur les méthodes d’apprentissage Bayésiennes nonparamétriques a porté sur trois aspects principaux : la construction de nouveaux modèles, le développement d’algorithmes d’inférence et les applications. Cette thèse présente nos contributions à ces trois sujets de recherches dans le contexte d’apprentissage de modèles à variables cachées. Dans un premier temps, nous introduisons le Pitman-Yor process mixture of Gaussians, un modèle permettant l’apprentissage de mélanges infinis de Gaussiennes. Nous présentons aussi un algorithme d’inférence permettant de découvrir les composantes cachées du modèle que nous évaluons sur deux applications concrètes de robotique. Nos résultats démontrent que l’approche proposée surpasse en performance et en flexibilité les approches classiques d’apprentissage. Dans un deuxième temps, nous proposons l’extended cascading Indian buffet process, un modèle servant de distribution de probabilité a priori sur l’espace des graphes dirigés acycliques. Dans le contexte de réseaux Bayésien, ce prior permet d’identifier à la fois la présence de variables cachées et la structure du réseau parmi celles-ci. Un algorithme d’inférence Monte Carlo par chaîne de Markov est utilisé pour l’évaluation sur des problèmes d’identification de structures et d’estimation de densités. Dans un dernier temps, nous proposons le Indian chefs process, un modèle plus général que l’extended cascading Indian buffet process servant à l’apprentissage de graphes et d’ordres. L’avantage du nouveau modèle est qu’il admet les connections entres les variables observables et qu’il prend en compte l’ordre des variables. Nous présentons un algorithme d’inférence Monte Carlo par chaîne de Markov avec saut réversible permettant l’apprentissage conjoint de graphes et d’ordres. L’évaluation est faite sur des problèmes d’estimations de densité et de test d’indépendance. Ce modèle est le premier modèle Bayésien nonparamétrique permettant d’apprendre des réseaux Bayésiens disposant d’une structure complètement arbitraire.

Multiphase modeling of melting / solidification with high density variations using XFEM

La modélisation de la cryolite, utilisée dans la fabrication de l’aluminium, implique plusieurs défis, notament la présence de discontinuités dans la solution et l’inclusion de la difference de densité entre les phases solide et liquide. Pour surmonter ces défis, plusieurs éléments novateurs ont été développés dans cette thèse. En premier lieu, le problème du changement de phase, communément appelé problème de Stefan, a été résolu en deux dimensions en utilisant la méthode des éléments finis étendue. Une formulation utilisant un multiplicateur de Lagrange stable spécialement développée et une interpolation enrichie a été utilisée pour imposer la température de fusion à l’interface. La vitesse de l’interface est déterminée par le saut dans le flux de chaleur à travers l’interface et a été calculée en utilisant la solution du multiplicateur de Lagrange. En second lieu, les effets convectifs ont été inclus par la résolution des équations de Stokes dans la phase liquide en utilisant la méthode des éléments finis étendue aussi. Troisièmement, le changement de densité entre les phases solide et liquide, généralement négligé dans la littérature, a été pris en compte par l’ajout d’une condition aux limites de vitesse non nulle à l’interface solide-liquide pour respecter la conservation de la masse dans le système. Des problèmes analytiques et numériques ont été résolus pour valider les divers composants du modèle et le système d’équations couplés. Les solutions aux problèmes numériques ont été comparées aux solutions obtenues avec l’algorithme de déplacement de maillage de Comsol. Ces comparaisons démontrent que le modèle par éléments finis étendue reproduit correctement le problème de changement phase avec densités variables.

O treino pliométrico na melhoria da capacidade de salto no âmbito das aulas de técnica de dança moderna no 3º ciclo da Escola de Dança Ana Mangericão

Relatório Final de Estágio apresentado à Escola Superior de Dança, com vista à obtenção do grau de Mestre em Ensino de Dança.

Understanding the Reaction Mechanism of Nanocomposite Thermites

Nanocomposite energetics are a relatively new class of materials that combine nanoscale fuels and oxidizers to allow for the rapid release of large amounts of energy. In thermite systems (metal fuel with metal oxide oxidizer), the use of nanomaterials has been illustrated to increase reactivity by multiple orders of magnitude as a result of the higher specific surface area and smaller diffusion length scales. However, the highly dynamic and nanoscale processes intrinsic to these materials, as well as heating rate dependencies, have limited our understanding of the underlying processes that control reaction and propagation. For my dissertation, I have employed a variety of experimental approaches that have allowed me to probe these processes at heating rates representative of free combustion with the goal of understanding the fundamental mechanisms. Dynamic transmission electron microscopy (DTEM) was used to study the in situ morphological change that occurs in nanocomposite thermite materials subjected to rapid (10^11 K/s) heating. Aluminum nanoparticle (Al-NP) aggregates were found to lose their nanostructure through coalescence in as little as 10 ns, which is much faster than any other timescale of combustion. Further study of nanoscale reaction with CuO determined that a condensed phase interfacial reaction could occur within 0.5-5 µs in a manner consistent with bulk reaction, which supports that this mechanism plays a dominant role in the overall reaction process. Ta nanocomposites were also studied to determine if a high melting point (3280 K) affects the loss of nanostructure and rate of reaction. The condensed phase reaction pathway was further explored using reactive multilayers sputter deposited onto thin Pt wires to allow for temperature jump (T-Jump) heating at rates of ~5x10^5 K/s. High speed video and a time of flight mass spectrometry (TOFMS) were used to observe ignition temperature and speciation as a function of bilayer thickness. The ignition process was modeled and a low activation energy for effective diffusivity was determined. T-Jump TOFMS along with constant volume combustion cell studies were also used to determine the effect of gas release in nanoparticle systems by comparing the reaction properties of CuO and Cu2O.

DIRECT NUMERICAL SIMULATION OF INCOMPRESSIBLE MULTIPHASE FLOW WITH PHASE CHANGE

Phase change problems arise in many practical applications such as air-conditioning and refrigeration, thermal energy storage systems and thermal management of electronic devices. The physical phenomenon in such applications are complex and are often difficult to be studied in detail with the help of only experimental techniques. The efforts to improve computational techniques for analyzing two-phase flow problems with phase change are therefore gaining momentum. The development of numerical methods for multiphase flow has been motivated generally by the need to account more accurately for (a) large topological changes such as phase breakup and merging, (b) sharp representation of the interface and its discontinuous properties and (c) accurate and mass conserving motion of the interface. In addition to these considerations, numerical simulation of multiphase flow with phase change introduces additional challenges related to discontinuities in the velocity and the temperature fields. Moreover, the velocity field is no longer divergence free. For phase change problems, the focus of developmental efforts has thus been on numerically attaining a proper conservation of energy across the interface in addition to the accurate treatment of fluxes of mass and momentum conservation as well as the associated interface advection. Among the initial efforts related to the simulation of bubble growth in film boiling applications the work in \cite{Welch1995} was based on the interface tracking method using a moving unstructured mesh. That study considered moderate interfacial deformations. A similar problem was subsequently studied using moving, boundary fitted grids \cite{Son1997}, again for regimes of relatively small topological changes. A hybrid interface tracking method with a moving interface grid overlapping a static Eulerian grid was developed \cite{Juric1998} for the computation of a range of phase change problems including, three-dimensional film boiling \cite{esmaeeli2004computations}, multimode two-dimensional pool boiling \cite{Esmaeeli2004} and film boiling on horizontal cylinders \cite{Esmaeeli2004a}. The handling of interface merging and pinch off however remains a challenge with methods that explicitly track the interface. As large topological changes are crucial for phase change problems, attention has turned in recent years to front capturing methods utilizing implicit interfaces that are more effective in treating complex interface deformations. The VOF (Volume of Fluid) method was adopted in \cite{Welch2000} to simulate the one-dimensional Stefan problem and the two-dimensional film boiling problem. The approach employed a specific model for mass transfer across the interface involving a mass source term within cells containing the interface. This VOF based approach was further coupled with the level set method in \cite{Son1998}, employing a smeared-out Heaviside function to avoid the numerical instability related to the source term. The coupled level set, volume of fluid method and the diffused interface approach was used for film boiling with water and R134a at the near critical pressure condition \cite{Tomar2005}. The effect of superheat and saturation pressure on the frequency of bubble formation were analyzed with this approach. The work in \cite{Gibou2007} used the ghost fluid and the level set methods for phase change simulations. A similar approach was adopted in \cite{Son2008} to study various boiling problems including three-dimensional film boiling on a horizontal cylinder, nucleate boiling in microcavity \cite{lee2010numerical} and flow boiling in a finned microchannel \cite{lee2012direct}. The work in \cite{tanguy2007level} also used the ghost fluid method and proposed an improved algorithm based on enforcing continuity and divergence-free condition for the extended velocity field. The work in \cite{sato2013sharp} employed a multiphase model based on volume fraction with interface sharpening scheme and derived a phase change model based on local interface area and mass flux. Among the front capturing methods, sharp interface methods have been found to be particularly effective both for implementing sharp jumps and for resolving the interfacial velocity field. However, sharp velocity jumps render the solution susceptible to erroneous oscillations in pressure and also lead to spurious interface velocities. To implement phase change, the work in \cite{Hardt2008} employed point mass source terms derived from a physical basis for the evaporating mass flux. To avoid numerical instability, the authors smeared the mass source by solving a pseudo time-step diffusion equation. This measure however led to mass conservation issues due to non-symmetric integration over the distributed mass source region. The problem of spurious pressure oscillations related to point mass sources was also investigated by \cite{Schlottke2008}. Although their method is based on the VOF, the large pressure peaks associated with sharp mass source was observed to be similar to that for the interface tracking method. Such spurious fluctuation in pressure are essentially undesirable because the effect is globally transmitted in incompressible flow. Hence, the pressure field formation due to phase change need to be implemented with greater accuracy than is reported in current literature. The accuracy of interface advection in the presence of interfacial mass flux (mass flux conservation) has been discussed in \cite{tanguy2007level,tanguy2014benchmarks}. The authors found that the method of extending one phase velocity to entire domain suggested by Nguyen et al. in \cite{nguyen2001boundary} suffers from a lack of mass flux conservation when the density difference is high. To improve the solution, the authors impose a divergence-free condition for the extended velocity field by solving a constant coefficient Poisson equation. The approach has shown good results with enclosed bubble or droplet but is not general for more complex flow and requires additional solution of the linear system of equations. In current thesis, an improved approach that addresses both the numerical oscillation of pressure and the spurious interface velocity field is presented by featuring (i) continuous velocity and density fields within a thin interfacial region and (ii) temporal velocity correction steps to avoid unphysical pressure source term. Also I propose a general (iii) mass flux projection correction for improved mass flux conservation. The pressure and the temperature gradient jump condition are treated sharply. A series of one-dimensional and two-dimensional problems are solved to verify the performance of the new algorithm. Two-dimensional and cylindrical film boiling problems are also demonstrated and show good qualitative agreement with the experimental observations and heat transfer correlations. Finally, a study on Taylor bubble flow with heat transfer and phase change in a small vertical tube in axisymmetric coordinates is carried out using the new multiphase, phase change method.

Electrolytes for ceramic oxide fuel cells

The main objective of this dissertation is the development and processing of novel ionic conducting ceramic materials for use as electrolytes in proton or oxide-ion conducting solid oxide fuel cells. The research aims to develop new processing routes and/or materials offering superior electrochemical behavior, based on nanometric ceramic oxide powders prepared by mechanochemical processes. Protonic ceramic fuel cells (PCFCs) require electrolyte materials with high proton conductivity at intermediate temperatures, 500-700ºC, such as reported for perovskite zirconate oxides containing alkaline earth metal cations. In the current work, BaZrO3 containing 15 mol% of Y (BZY) was chosen as the base material for further study. Despite offering high bulk proton conductivity the widespread application of this material is limited by its poor sinterability and grain growth. Thus, minor additions of oxides of zinc, phosphorous and boron were studied as possible sintering additives. The introduction of ZnO can produce substantially enhanced densification, compared to the un-doped material, lowering the sintering temperature from 1600ºC to 1300ºC. Thus, the current work discusses the best solid solution mechanism to accommodate this sintering additive. Maximum proton conductivity was shown to be obtained in materials where the Zn additive is intentionally adopted into the base perovskite composition. P2O5 additions were shown to be less effective as a sintering additive. The presence of P2O5 was shown to impair grain growth, despite improving densification of BZY for intermediate concentrations in the range 4 – 8 mol%. Interreaction of BZY with P was also shown to have a highly detrimental effect on its electrical transport properties, decreasing both bulk and grain boundary conductivities. The densification behavior of H3BO3 added BaZrO3 (BZO) shows boron to be a very effective sintering aid. Nonetheless, in the yttrium containing analogue, BaZr0.85Y0.15O3- (BZY) the densification behavior with boron additives was shown to be less successful, yielding impaired levels of densification compared to the plain BZY. This phenomenon was shown to be related to the undesirable formation of barium borate compositions of high melting temperatures. In the last section of the work, the emerging oxide-ion conducting materials, (Ba,Sr)GeO3 doped with K, were studied. Work assessed if these materials could be formed by mechanochemical process and the role of the ionic radius of the alkaline earth metal cation on the crystallographic structure, compositional homogeneity and ionic transport. An abrupt jump in oxide-ion conductivity was shown on increasing operation temperature in both the Sr and Ba analogues.

The influence of past behavior on future behavior: a mind-set perspective

A behavioral mind-set refers to the effect of performing a behavior in one situation (e.g., deciding which animals jump higher, dolphins or sea lions) on the likelihood of performing a conceptually similar behavior in subsequent, unrelated situations (e.g., deciding which of two candies to purchase). It reflects the activation and persistence of procedural knowledge. My dissertation circumscribes the construct of a behavioral mind-set and proposes a theoretical framework describing how mind-sets operate as well as their cognitive and motivational determinants. Three sets of studies investigated the role of mind-sets in different domains. The first set of studies explored the influence of making comparative judgments on subsequent decision making. Specifically, I found that making comparative judgment in one situation activates a which-to-buy mind-set that increases the willingness to decide which of two products to purchase in a later situation without considering the option of not buying anything at all. This mind-set can be activated not only by stating preferences for one of two products but also by comparing the relative attractiveness of wild animals, comparing the animals with respect to physical attributes, and estimating how similar one object is to another. Furthermore, the mind-set, once activated, influences not only purchase intentions in hypothetical situations but the actual decisions to purchase one of different types of products that are on sale after the experiment. The second set of studies investigated whether generating supportive elaborations or counterarguments in one situation will influence people’s tendency to engage in similar behavior in a subsequent, unrelated situation. I found that making supportive elaborations in one situation gives rise to a bolstering mind-set that, once activated, increases participants’ disposition to generate supportive thoughts in response to persuasive communications that they receive later and, therefore, increases the effectiveness of persuasion. Correspondingly, generating opposing arguments in an initial situation activates a counterarguing mind-set that increases the tendency to argue against the persuasive communications and decreases its effectiveness. However, a counterarguing mind-set may increase the effectiveness of persuasion if the messages are difficult to be refuted. The third set of studies distinguished between the influence of motivation on consumer behavior and the influence of a mind-set that is activated by this motivation. Specifically, I found that appetitive motivation, which naturally increases people’s tendency to acquire food products, can give rise to a cognition-based acquisition mind-set that increases people’s disposition to acquire non-food products as well. This acquisition mind-set may persist even when the appetitive motivation that gave rise to it is satiated by eating. Moreover, the disposition to acquire non-food products is not mediated by the products’ attractiveness. The studies suggest that motivation and mind-sets may independently influence consumers’ evaluation of a product and their dispositions to acquire it. Motivation is more likely to influence product evaluations whereas a mind-set is more likely to influence consumers’ acquisition dispositions. In summary, a behavioral mind-set can be activated in the process of performing a behavior. And the mind-set may influence people’s subsequent behaviors in unrelated situations in which the activated procedure is applicable. Moreover, motivation to engage in one behavior could also elicit a cognition-based mind-set, which may change people’s subsequent behaviors.