Learning to Interpret and Generate Instructional Recipes

Thesis (Ph.D.)--University of Washington, 2016-08

Microstructure characterization of 316L deformed at high strain rates using EBSD

Specimens from split Hopkinson pressure bar experiments, at strain rates between ~ 1000–9000 s− 1 at room temperature and 500 °C, have been studied using electron backscatter diffraction. No significant differences in the microstructures were observed at different strain rates, but were observed for different strains and temperatures. Size distribution for subgrains with boundary misorientations > 2° can be described as a bimodal lognormal area distribution. The distributions were found to change due to deformation. Part of the distribution describing the large subgrains decreased while the distribution for the small subgrains increased. This is in accordance with deformation being heterogeneous and successively spreading into the undeformed part of individual grains. The variation of the average size for the small subgrain distribution varies with strain but not with strain rate in the tested interval. The mean free distance for dislocation slip, interpreted here as the average size of the distribution of small subgrains, displays a variation with plastic strain which is in accordance with the different stages in the stress-strain curves. The rate of deformation hardening in the linear hardening range is accurately calculated using the variation of the small subgrain size with strain.

Modélisation du comportement des bétons fibrés à ultra-hautes performances par la micromécanique : Effet de l'orientation des fibres à l'échelle de la structure

Cette thèse s’inscrit dans le contexte d’une optimisation industrielle et économique des éléments de structure en BFUP permettant d’en garantir la ductilité au niveau structural, tout en ajustant la quantité de fibres et en optimisant le mode de fabrication. Le modèle développé décrit explicitement la participation du renfort fibré en traction au niveau local, en enchaînant une phase de comportement écrouissante suivie d’une phase adoucissante. La loi de comportement est fonction de la densité, de l’orientation des fibres vis-à-vis des directions principales de traction, de leur élancement et d’autres paramètres matériaux usuels liés aux fibres, à la matrice cimentaire et à leur interaction. L’orientation des fibres est prise en compte à partir d’une loi de probabilité normale à une ou deux variables permettant de reproduire n’importe quelle orientation obtenue à partir d’un calcul représentatif de la mise en oeuvre du BFUP frais ou renseignée par analyse expérimentale sur prototype. Enfin, le modèle reproduit la fissuration des BFUP sur le principe des modèles de fissures diffuses et tournantes. La loi de comportement est intégrée au sein d’un logiciel de calcul de structure par éléments finis, permettant de l’utiliser comme un outil prédictif de la fiabilité et de la ductilité globale d’éléments en BFUP. Deux campagnes expérimentales ont été effectuées, une à l’Université Laval de Québec et l’autre à l’Ifsttar, Marne-la-Vallée. La première permet de valider la capacité du modèle reproduire le comportement global sous des sollicitations typiques de traction et de flexion dans des éléments structurels simples pour lesquels l’orientation préférentielle des fibres a été renseignée par tomographie. La seconde campagne expérimentale démontre les capacités du modèle dans une démarche d’optimisation, pour la fabrication de plaques nervurées relativement complexes et présentant un intérêt industriel potentiel pour lesquels différentes modalités de fabrication et des BFUP plus ou moins fibrés ont été envisagés. Le contrôle de la répartition et de l’orientation des fibres a été réalisé à partir d’essais mécaniques sur prélèvements. Les prévisions du modèle ont été confrontées au comportement structurel global et à la ductilité mis en évidence expérimentalement. Le modèle a ainsi pu être qualifié vis-à-vis des méthodes analytiques usuelles de l’ingénierie, en prenant en compte la variabilité statistique. Des pistes d’amélioration et de complément de développement ont été identifiées.

A Study on the liquefaction risk in seismic design of foundations

A fully coupled non-linear effective stress response finite difference (FD) model is built to survey the counter-intuitive recent findings on the reliance of pore water pressure ratio on foundation contact pressure. Two alternative design scenarios for a benchmark problem are explored and contrasted in the light of construction emission rates using the EFFC-DFI methodology. A strain-hardening effective stress plasticity model is adopted to simulate the dynamic loading. A combination of input motions, contact pressure, initial vertical total pressure and distance to foundation centreline are employed, as model variables, to further investigate the control of permanent and variable actions on the residual pore pressure ratio. The model is verified against the Ghosh and Madabhushi high acceleration field test database. The outputs of this work is aimed to improve the current computer-aided seismic foundation design that relies on ground’s packing state and consistency. The results confirm that on seismic excitation of shallow foundations, the likelihood of effective stress loss is greater in deeper depths and across free field. For the benchmark problem, adopting a shallow foundation system instead of piled foundation benefitted in a 75% less emission rate, a marked proportion of which is owed to reduced materials and haulage carbon cost.

Sensibilidade à mudança de trajetória de deformação no aço TWIP980

Resultante dos avanços tecnológicos, conseguiu-se obter um aço que elimina o paradigma de se aliar alta ductilidade e resistência mecânica. Assim foi desenvolvido durante a última década o aço TWIP, deformação induzida por maclação, tendo como principal mecanismo de deformação a maclação. Este presente trabalho teve como principal objetivo caraterizar o aço TWIP980 em três temáticas diferentes: química, mecânica e microestrutura. Na primeira temática, a química, esta teve como objetivo encontrar a designação do aço TWIP em estudo. Sendo apenas conhecida a direção de laminação, RD, e a empresa que forneceu as chapas, a POSCO, o objetivo era obter a sua designação. Através da comparação das curvas de tração encontradas para o material em estudo, e conjuntamente, com as diversas curvas de tração de vários aços TWIP da empresa POSCO, realizou-se a comparação. Visto ter-se ficado reduzido a dois possíveis aços TWIP, foi através de uma análise à composição química, EDS - Espectroscopia da energia dispersa por raios-X, que se concluiu que o aço em estudo era o TWIP980. Na caraterização mecânica, e através de ensaios de tração, foram estudadas propriedades como: o módulo de elasticidade, tensão limite elástico, ductilidade, anisotropia, coeficiente de encruamento e Poisson. Estas propriedades foram estudas para três mudanças na trajetória de deformação e quatro pré-deformações em estudo. Assim estudou-se a alteração de trajetória para os ângulos a 0º, 45º e 90º em relação a RD, para as deformações de engenharia de 0%, 10%, 20% e 30%. Por último, na análise à microestrutura, esta teve como objetivo obter valores para o tamanho de grão e de macla bem como as suas orientações cristalográficas. Também a densidade de deslocações e maclação para cada uma das 4 pré-deformações esteve em estudo. Estes parâmetros foram obtidos através de microscopia ótica, eletrónica de varrimento, MEV e eletrónica de transmissão, MET.

Improving DPA and DFA resistance of circuits using asynchronous logic

International audience

La pena de prisión y sus alternativas

[ES] el objetivo del presente trabajo es mostrar las características generales de la actual realidad penitenciaria en cuanto a la pena de prisión y las penas alternativas. Se analiza la pena de prisión desde una perspectiva crítica dando a conocer las limitaciones que presenta la prisión en cuanto a los derechos de las personas presas y haciendo una descripción sobre los principales efectos negativos que genera sobre estas personas. Desde la consolidación del Código Penal de 1995 hasta la última reforma penal de 2015 se ha dado un incremento constante de la dureza de las penas, aumentando la duración de la pena de prisión y su cumplimiento dentro de la prisión. Consecuentemente, se reduce la aplicación de las penas alternativas a la prisión, contrariando así el principio constitucional descrito en el artículo 25.2 orientado a la resocialización del penado y el principio de intervención mínima o ultima ratio del Derecho Penal.

In-situ Molibdenum X-ray powder diffraction study of the early hydration of cementitious systems on a humidity chamber

The durability of cement-based construction materials depends on the environmental conditions during their service life. A further factor is the microstructure of the cement bulk, established by formation of cement hydrates. The development of the phases and microstructure under given conditions is responsible of the high strength of cementitious materials. The investigation on the early hydration behavior of cements and cementing systems has been for a long time a very important area of research: understanding the chemical reactions that lead to hardening is fundamental for the prediction of performances and durability of the materials. The production of 1 ton of Ordinary Portland Cement, OPC, releases into the atmosphere ~0.97 tons of CO2. This implies that the overall CO2 emissions from the cement industry are 6% of all anthropogenic carbon dioxide. An alternative to reduce the CO2 footprint consists on the development of eco-cements composed by less calcite demanding phases, such as belite and ye'elimite. That is the case of Belite-Ye’elimite cements (BY). Since the reactivity of belite is not quick enough, these materials develop low mechanical strengths at intermediate hydration ages. A possible solution to this problem goes through the production of cements which jointly contain alite with the two previously mentioned phases, named as Belite-Alite-Ye’elimite (BAY) cements. The reaction of alite and ye'elimite with water will develop cements with high mechanical strengths at early ages, while belite will contribute to later values. The final goal is to understand the hydration mechanisms of a variety of cementing systems (OPC, BAY and pure phases) as a function of water content, superplasticizer additives and type and content of sulfate source. In order to do so, in-situ laboratory humidity chambers with Molybdenum X-ray Powder diffraction are employed. In the first 2h of hydration, reaction degree (α) of ye'elimite had been decreased for superplasticizer.

Trust and Leadership in Higher Education in the Downturn

This Leadership Academy Workshop presentation focused on 'Trust and Leadership in the Downturn', with particular reference to the public sector and to education. The presentation discussed a range of definitions of trust, including the view of Mayer, Davis and Schoorman (1995) that trust can be described as 'the willingness of a person to be vulnerable to the actions of another, based on the expectation that the other will perform a particular action important to the trustor, irrespective of the ability to monitor or control that action'. The presentation then focused on the reasons why this relational psychological state is important,particularly in an economic recession when people were facing job cuts and economic uncertainty in a wider political and social environment characterised by cynicism and a downturn in trust. If trust is defined in part as a belief in the honesty, competence and benevolence of others, it tends to act like 'social glue', cushioning difficult situations and enabling actions to take place easily that otherwise would not be permissible. A worrying state of affairs has recently been developing across the world, however, in the economic downturn, as reported in the Edelman Trust Barometer for 2009, in which there was a marked diminuition of trust in corporations, businesses and government, as a result of the credit crunch. While the US and parts of Europe was showing recovery from a generalised loss of trust by mid-year 2009, the UK had not. It seems that social attitudes in Britain may be hardening - it seems that from being a nation of sceptics we may be becoming a nation of cynics: for example, 69% of the population surveyed by Edelman trust the government less than six months ago. In this situation, there is a need to promote positive measures to build trust, including the establishment of more transparent and honest business practices and practices to ensure that employees are treated well. Following the presentation, a workshop was held to discuss the nature of a possible loss of trust in the downturn in the UK and its implications for leadership practices and development.

Avaliação do efeito da adição de resíduo de borracha de pneu e brita calcária na formulação de compósitos cimentíceos

Researches have shown that the introduction of rubber in concrete improves the features of its deformability, as well as contributes to environmental disposal of waste generated in the tire retreading process. Furthermore, there is a high availability of limestone within RN and CE country. Ignorance about this stone, does not allow its wide use as aggregate, leaving, this abundant supply idle. A composite of limestone gravel, with proportions of tire rubber waste which could be used as concrete would be an alternative to concrete for low applications. Therefore, this research aims to evaluate the characteristics of concrete containing limestone gravel and proportions of little aggregate replacement (sand) by tire rubber waste. To this goal, the material components of the concrete were characterized, concrete specimens with limestone gravel were made, from the dash 1.0: 2.5: 3.5, varying the water/cement ratio, and inserting a commercial plasticizer, without a proportion of residue, known as reference. From this, concrete with and without the presence of the additive in the same proportions were chosen, as well as these with the use of granite gravel, for being the most used. Selected the references, to these, replacements of little aggregate (sand) were added replaced by rubber waste from the tire retreading process, treated with 1M NaOH in proportions from 5.0 to 20.0 % by mass, cured and exposed to the semiarid environment. The results indicate the possibility of using limestone gravel in the concrete composition with workability correction using plasticizer. There was a decrease in the mechanical properties of the concrete with increments of waste rubber, but there is an improvement in toughness and deformability of the composite, which makes it interesting for the construction of non-structural concrete floors, as well as, the rubber waste delayed the hardening process, continuing to gain resistance after 28 days

Wrinkling during cup drawing with NUMISHEET2014 benchmark test

Wrinkling occurs when a blank is subjected to compressive stresses during the forming process as in the flange of a cup during drawing. Although the failure limit due to plastic flow localization can be simply defined by the FLC at each point of a continuum, the wrinkling limit cannot be defined with simple variables such as strain, stress, and thickness. Wrinkling is strongly affected by the mechanical properties of the sheet material, the geometry of the tools and blank, and contact conditions. The analysis of wrinkling initiation and growth is, therefore, difficult to perform due to the complex synergistic effects of the controlling parameters. Because of these difficulties, the study of wrinkling has generally been conducted case by case. A unique wrinkling criterion, which could be used effectively for various sheet forming processes, has not yet been proposed. There were many investigations on the effect of process parameters (BHF and friction) and geometry on wrinkling. However, there are few reported results on the influence of the material model on wrinkling. This paper shows how strain hardening and r-values affect wrinkle formation in its magnitude, initiation, and direction through the NUMISHEET2014 benchmark test for wrinkling during cup drawing.