Estanho na Amazônia: o apogeu e o caso da produção

No Brasil, na Região Amazônica, o minério de estanho (cassiterita) é obtido por dragagem em depósitos aluvionares, extração de minério primário e lavra de pequeno porte. O concentrado de estanho obtido (Sn02, contendo 60% de estanho), sendo transformado, via redução, nos fornos elétricos, transformando-o em lingotes de estanho. O metal é primeiramente usado para a produção de folhas de flandres – chapas de aço recobertas com estanho e utilizadas para fabricação de latas para alimentos, bebidas e produtos químicos, bem como na produção de soldas e outras ligas para a indústria em geral (particularmente em segmentos elétricos e eletrônicos). A mina mais importante é a de Pitinga (pureza de 55,3%), localizada a 300 km ao norte de Manaus (AM) e proprietária da Paranapenema. Pitinga dispõe de reservas provadas de columbita-tantalita, criolita e zirconita, contendo terras raras e itrium, cuja viabilidade econômica ainda está sendo estudada. Há inda veios mineralizados no estado de Rondônia, incluindo a mina de Bom Futuro (pureza de 58%), no município de Ariquemes, onde operam os mineradores de pequeno porte. O Brasil é o quinto maior produtor do metal, após Indonésia, China e Peru.

The columnar to equiaxed transition of horizontal unsteady-state directionally solidified Al-Si alloys

Experiments were conducted to investigate the influence of thermal parameters on the columnar to equiaxed transition during the horizontal unsteady-state directional solidification of Al-Si alloys. The parameters analyzed include the heat transfer coefficients, growth rates, cooling rates, temperature gradients and composition. A combined theoretical and experimental approach is developed to determine the solidification thermal variables considered. The increasing solute content in Al-Si alloys was not found to affect significantly the experimental position of the CET which occurred for cooling rates in the range between 0.35 and 0.64 K/s for any of three alloy compositions examined. A comparative analysis between the results of this work and those from the literature proposed to analyze the CET during upward vertical solidification of Al-Si alloys is reported and the results have shown that the end of the columnar region during horizontal directional solidification is abbreviated as a result of about six times higher thermal gradient than that verified during upward unidirectional solidification of alloys investigated.

Interstitial oxygen's influence on the corrosion behavior of Ti-9Mo alloys

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Thermal investigation and infrared evolved gas analysis of solid trivalent lanthanide and yttrium alpha-hydroxyisobutyrates in N-2 and CO2 atmospheres

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Ti-Mo alloys employed as biomaterials: Effects of composition and aging heat treatment on microstructure and mechanical behavior

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Tribocorrosion response of the Ti6Al4V alloys commonly used in femoral stems

In prosthesis, tribochemical reactions occur at the stem/bone interface. When coupled with micromotions it can lead to the loosening of the implant, osteolysis, release of metal ion and wear particles. The effect of these movements and the underlying mechanisms are quite unknown. This work investigates the tribocorrosion behavior of etched Ti6Al4V alloys under reciprocating sliding. Tests were performed in a phosphate buffer solution (PBS) containing proteins. A normal load of 1 N and anodic potentials of -0.1 and +0.5 V/SCE were applied. The destruction pathways of the top surface layers (adsorbed proteins, passive film) were studied. The results showed that the favorable/undesired effect of proteins in solution depends on the characteristics of the passive film under a mechanical stress. (C) 2013 Elsevier Ltd. All rights reserved.

The Influence of Small Quantities of Oxygen in the Structure, Microstructure, Hardness, Elasticity Modulus and Cytocompatibility of Ti-Zr Alloys for Dental Applications

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Are new TiNbZr alloys potential substitutes of the Ti6Al4V alloy for dental applications? An electrochemical corrosion study

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Electrodeposition of Ni-B and Ni-Co-B Alloys by Using Boric Acid as Boron Source

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

SVET, SKP and EIS study of the corrosion behaviour of high strength Al and Al-Li alloys used in aircraft fabrication

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)

Effects of laser beam energy on the pulsed Nd:YAG laser welding of thin sheet corrosion resistant materials

The aim of this study was to value the possibility to join, for pulsed Nd:YAG laser welding, thin foils lap joints for sealing components in corrosive environment. Experimental investigations were carried out using a pulsed neodymium: yttrium aluminum garnet laser weld to examine the influence of the pulse energy in the characteristics of the weld fillet. The pulse energy was varied from 1.0 to 2.5 J at increments of 0.25 J with a 4 ms pulse duration. The base materials used for this study were AISI 316L stainless steel and Ni-based alloys foils with 100 mu m thickness. The welds were analyzed by electronic and optical microscopy, tensile shear tests and micro hardness. The results indicate that pulse energy control is of considerable importance to thin foil weld quality because it can generate good mechanical properties and reduce discontinuities in weld joints. The ultimate tensile strength of the welded joints increased at first and then decreased as the pulse energy increased. In all the specimens, fracture occurred in the top foil heat-affected zone next to the fusion line. The microhardness was almost uniform across the parent metal, HAZ and weld metal. A slight increase in the fusion zone and heat-affected zone compared to those measured in the base metal was observed. This is related to the microstructural refinement in the fusion zone, induced by rapid cooling of the laser welding. The process appeared to be very sensitive to the gap between couples.

Martensite decomposition in Cu-Al-Mn-Ag alloys

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Structural, morphological and magnetic characterization of electrodeposited Co-Fe-W alloys

Conselho Nacional de Desenvolvimento Científico e Tecnológico (CNPq)

Spectroscopic, luminescence and in vitro biological studies of solid ketoprofen of heavier trivalent lanthanides and yttrium(III)

Fundação de Amparo à Pesquisa do Estado de São Paulo (FAPESP)

Corrosion properties of Fe-Cr-Nb-B amorphous alloys and coatings

Coordenação de Aperfeiçoamento de Pessoal de Nível Superior (CAPES)