A fast acting detector for abnormal output voltages of an UPS system

A new method of sensing the abnormal output voltage conditions of a single phase UPS system is presented, which provides the information almost instantaneously, so that a fast load transfer can be initiated. A continuous monitoring of the UPS output instantaneous voltage is used so that any under/over voltage, transients, or waveform distortion present can be detected.

Using tau polarization to probe the stau co-annihilation region of the minimal supergravity model at the LHC

The minimal supergravity model predicts the polarization of the tau coming from the stau to bino decay in the co-annihilation region to +1. This can be exploited to extract this soft tau signal at LHC and also to measure the tiny mass differences between the stau and the bi lightest superparticle. Moreover, this strategy will be applicable for a wider class of bino lightest superparticle models, where the lighter stau has a right component at least of similar size as the left.

A Radical Cyclization Route To +/-Andirolactone, A Spiro-Gamma-Butyrolactone

Synthesis of Andirolactone (Image ), starting from 4-methyl cyclohex-3-en-1-one (Image ), via the radical cyclisation of the bromoacetal (Image ), is described.

Availability of soil potassium and diagnostic soil tests

Thirty-seven surface (0-0.10 or 0-0.20 m) soils covering a wide range of soil types (16 Vertosols, 6 Ferrosols, 6 Dermosols, 4 Hydrosols, 2 Kandosols, 1 Sodosol, 1 Rudosol, and 1 Chromosol) were exhaustively cropped in 2 glasshouse experiments. The test species were Panicum maximum cv. Green Panic in Experiment A and Avena sativa cv. Barcoo in Experiment B. Successive forage harvests were taken until the plants could no longer grow in most soils because of severe potassium (K) deficiency. Soil samples were taken prior to cropping and after the final harvest in both experiments, and also after the initial harvest in Experiment B. Samples were analysed for solution K, exchangeable K (Exch K), tetraphenyl borate extractable K for extraction periods of 15 min (TBK15) and 60 min (TBK60), and boiling nitric acid extractable K (Nitric K). Inter-correlations between the initial levels of the various soil K parameters indicated that the following pools were in sequential equilibrium: solution K, Exch K, fast release fixed K [estimated as (TBK15-Exch K)], and slow release fixed K [estimated as (TBK60-TBK15)]. Structural K [estimated as (Nitric K-TBK60)] was not correlated with any of the other pools. However, following exhaustive drawdown of soil K by cropping, structural K became correlated with solution K, suggesting dissolution of K minerals when solution K was low. The change in the various K pools following cropping was correlated with K uptake at Harvest 1 ( Experiment B only) and cumulative K uptake ( both experiments). The change in Exch K for 30 soils was linearly related to cumulative K uptake (r = 0.98), although on average, K uptake was 35% higher than the change in Exch K. For the remaining 7 soils, K uptake considerably exceeded the change in Exch K. However, the changes in TBK15 and TBK60 were both highly linearly correlated with K uptake across all soils (r = 0.95 and 0.98, respectively). The slopes of the regression lines were not significantly different from unity, and the y-axis intercepts were very small. These results indicate that the plant is removing K from the TBK pool. Although the change in Exch K did not consistently equate with K uptake across all soils, initial Exch K was highly correlated with K uptake (r = 0.99) if one Vertosol was omitted. Exchangeable K is therefore a satisfactory diagnostic indicator of soil K status for the current crop. However, the change in Exch K following K uptake is soil-dependent, and many soils with large amounts of TBK relative to Exch K were able to buffer changes in Exch K. These soils tended to be Vertosols occurring on floodplains. In contrast, 5 soils (a Dermosol, a Rudosol, a Kandosol, and 2 Hydrosols) with large amounts of TBK did not buffer decreases in Exch K caused by K uptake, indicating that the TBK pool in these soils was unavailable to plants under the conditions of these experiments. It is likely that K fertiliser recommendations will need to take account of whether the soil has TBK reserves, and the availability of these reserves, when deciding rates required to raise exchangeable K status to adequate levels.

Site-Specific Functionalization of Hyperbranched Polymers Using ``Click'' Chemistry

Different strategies for functionalization of the core region and periphery of core-shell type hyperbranched polymers (HBP) using the ``click'' reaction have been explored. For achieving periphera functionalization, an AB(2) + A-R-1 + A-R-2 type copolymerization approach was used, where A-R-1 is heptaethylene glycol monomethyl ether (HPEG-M) and A-R-2 is tetraethylene glycol monopropargyl ether (TEG-P). A very small mole fraction of the propargyl containing monomer, TEG-P, was used to ensure that the water-solubility of the hyperbranched polymer is minimally affected. Similarly, to incorporate propargyl groups in the core region, a new propargyl group bearing B-2-typ monomer was designed and utilized in an AB(2) + A(2) + B-2 + A-R-1 type copolymerization, such that the total mole fraction of B-2 + A(2) is small and their mole-ratio is 1: 1. Further, using a combination of both the above approaches, namely AB(2) + A(2) + B-2 + A-R-1 + A-R-2, hyperbranched structures that incorporate propargyl groups both at theperiphery and within the core were synthesized. Since the AB(2) monomer carries a hexamethylene spacer (C-6) and the periphery is PEGylated all the derivatized polymers form core-shell type structures in aqueous solutions. Attempts were made to ascertain and probe the location of the propargyl groups in these HBP's, by ``clicking'' azidomethylpyrene, onto them. However, the fluorescence spectra of aqueous solutions of the pyrene derivatized polymers were unable to discriminate between the various locations, possibly because the relatively hydrophobic pyrene units insert themselves into the core region to minimize exposure to water.

A fluctuation-based probe to athermal phase transitions

We focus on athermal phase transitions where in discrete and dissipative avalanches are observed in physical observables as the system jumps from one metastable state to another, when driven by an external field. Using higher order statistics of time dependent avalanches, or noise, in electrical resistivity during temperature-driven martensite transformation in thin nickel-titanium films, we demonstrate evidence suggesting the existence of a singular `global instability' or divergence of the correlation length as a function of temperature at the transition. These results not only establish a mapping of non-equilibrium first order phase transition and equilibrium critical phenomena, but perhaps also call for a re-evaluation of many existing experimental claims of self-organized criticality.

Language in Acquisition : Early Lexical Development and Associations between Lexicon and Grammar Findings from Full-Term and Very-Low-Birth-Weight Finnish Children

The aim was to analyse the growth and compositional development of the receptive and expressive lexicons between the ages 0,9 and 2;0 in the full-term (FT) and the very-low-birth-weight (VLBW) children who are acquiring Finnish. The associations between the expressive lexicon and grammar at 1;6 and 2;0 in the FT children were also studied. In addition, the language skills of the VLBW children at 2;0 were analysed, as well as the predictive value of early lexicon to the later language performance. Four groups took part in the studies: the longitudinal (N = 35) and cross-sectional (N = 146) samples of the FT children, and the longitudinal (N = 32) and cross-sectional (N = 66) samples of VLBW children. The data was gathered by applying of the structured parental rating method (the Finnish version of the Communicative Development Inventory), through analysis of the children´s spontaneous speech and by administering a a formal test (Reynell Developmental Language Scales). The FT children acquired their receptive lexicons earlier, at a faster rate and with larger individual variation than their expressive lexicons. The acquisition rate of the expressive lexicon increased from slow to faster in most children (91%). Highly parallel developmental paths for lexical semantic categories were detected in the receptive and expressive lexicons of the Finnish children when they were analysed in relation to the growth of the lexicon size, as described in the literature for children acquiring other languages. The emergence of grammar was closely associated with expressive lexical growth. The VLBW children acquired their receptive lexicons at a slower rate and had weaker language skills at 2;0 than the full-term children. The compositional development of both lexicons happened at a slower rate in the VLBW children when compared to the FT controls. However, when the compositional development was analysed in relation to the growth of lexicon size, this development occurred qualitatively in a nearly parallel manner in the VLBW children as in the FT children. Early receptive and expressive lexicon sizes were significantly associated with later language skills in both groups. The effect of the background variables (gender, length of the mother s basic education, birth weight) on the language development in the FT and the VLBW children differed. The results provide new information of early language acquisition by the Finnish FT and VLBW children. The results support the view that the early acquisition of the semantic lexical categories is related to lexicon growth. The current findings also propose that the early grammatical acquisition is closely related to the growth of expressive vocabulary size. The language development of the VLBW children should be followed in clinical work.

Fast Accurate Transient Stability Simulations

The paper describes a Simultaneous Implicit (SI) approach for transient stability simulations based on an iterative technique using traingularised admittance matrix [1]. The reduced saliency of generator in the subtransient state is taken advantage of to speed up the algorithm. Accordingly, generator differential equations, except rotor swing, contain voltage proportional to fluxes in the main field, dampers and a hypothetical winding representing deep flowing eddy currents, as state variables. The simulation results are validated by comparison with two independent methods viz. Runge-Kutta simulation for a simplified system and a method based on modelling damper windings using conventional induction motor theory.

Esr study of (SO4)2- dynamics in relation to the ferroelectric phase transition in ammonium sulfate

Ferroelectric phase transition in ammonium sulfate has been studied by ESR of CrO43- radical substituting for SO42- ion in (NH4)2SO4. In addition to discontinuous changes at Tc, certain continuous changes are observed in ESR parameters of this probe below Tc, which reflect the role of the sulfate ion in the phase transition. A microscopic mechanism of the phase transition is proposed and discussed in terms of the change of orientation of the sulfate tetrahedron through a finite angle. The degree of the change of orientation below Tc is thought to be the possible order parameter of the phase transition.

Käsityöläisyyden kuva kultasepän ammatissa : Käsityöläisyys Suomen Kultaseppien Liiton lehdessä 1990-luvun lopussa

The aim of this study is to survey the meaning of craftmanship in goldsmith occupation. The image of craftmanship is built theoretically as well as researcher's own practical experience. The study describes a dialogue between self-employed goldsmith s everyday work and trade union's opinion. Suomen Kultaseppien Liitto (The Goldsmith Assosiation of Finland) was chosen forthe trade union, because it is the biggest, the oldest and the most influential on the occupational area. The research data are volumes 1995 - 1998 of occupational membership journal of Suomen Kultaseppien Liitto. The data analyzed with Adapted Content Analysis and Grounded Theory. The professional occupation of goldsmiths, the role of craftmanship and the future of the occupation are discussed. Additionally, the relationship between the Suomen Kultaseppien Liitto and occupational culture and profession of goldsmiths was studied. Craft and craftmanship is most often discussed in articles related to tradition and education.Craftmanship is understood very idealistically, with little meaning in practical life. St. Eligius and the skill and art of goldsmiths in St Petersburg are raised to symbols of craftmanship. The occupational image is broken and a clear conflict between education and occupation is visible. Education produces artist-craftsmen, while handicraft workers are required in industry, and retailers or specially trained store assistant in business. Computer-aided design and manufacture render handicraft workmanship unnecessary. In a pessimistic view, the future possibilities of the goldsmith occupational profession are dim, because the artist-craftsmen are bound to lose to fast-paced machines. On the other hand, people involved in goldsmith education see the future light, designer-goldsmiths developing the occupational to new dimensions. Suomen Kultaseppien Liitto represents goldsmiths in public. The union, however is governed by non-artisan goldsmiths. The union stresses business attitudes and enterpreneurship, and has succeeded in protecting the privileges of retailers and industry. Goldsmiths profession is seen in the research data as a combination of precious-metal industry, jewellery and watch stores, anda goldsmith shop is considered a specialized giftstore. The goldsmiths occupation is not a profession, and the Suomen Kultaseppien Liitto is not a trade union for artist and craftmen. Accordingly, part of the representative authority of the union could be transferred from the Association to Taidekäsityöläiset Taiko ry, a member of organization of Ornamo. Results of this study show the importance of defining the images of the goldsmith occupational profession and the trade union. The results could be applied to goldsmith education to examine what would be the optimal education and training for present employment opportunities. The important background theories has been the theories of Habermas and Lévi-Strauss.

Kuva tikkeinä kankaalla : Kokemuksia PE-design 6.0 -kirjontakuvion suunnitteluohjelman kahden automaattisen tekniikan käytettävyydestä

The aim of the thesis was to compare the correspondence of the outcome a computer assisted program appearance compared to the original image. The aspect of the study was directed to embroidery with household machines. The study was made from the usability point of view with Brother's PE-design 6.0 embroidery design programs two automatic techniques; multicoloured fragment design and multicoloured stitch surface design. The study's subject is very current because of the fast development of machine embroidery. The theory is based on history of household sewing machines, embroidery sewing machines, stitch types in household sewing machines, embroidery design programs as well as PE-design 6.0 embroidery design program's six automatic techniques. Additionally designing of embroidery designs were included: original image, digitizing, punching, applicable sewing threads as well as the connection between embroidery designs and materials used on embroidery. Correspondences of sewn appearances were examined with sewing experimental methods. 18 research samples of five original image were sewn with both techniques. Experiments were divided into four testing stages in design program. Every testing stage was followed by experimental sewing with Brother Super Galaxie 3100D embroidery machine. Experiments were reported into process files and forms made for the techniques. Research samples were analysed on images syntactic bases with sensory perception assessment. Original images and correspondence of the embroidery appearances were analysed with a form made of it. The form was divided into colour and shape assessment in five stage-similarity-scale. Based on this correspondence analysis it can be said that with both automatic techniques the best correspondence of colour and shape was achieved by changing the standard settings and using the makers own thread chart and edited original image. According to the testing made it is impossible to inform where the image editing possibilities of the images are sufficient or does the optimum correspondence need a separate program. When aiming at correspondence between appearances of two images the computer is unable to trace by itself the appearance of the original image. Processing a computer program assisted embroidery image human perception and personal decision making are unavoidable.

A new probe for three-dimensional flow measurements

A new four-hole cylindrical cantilever probe is described which could be used for three-dimensional flow surveys. The probe is more compact than the usual cylindrical type allowing for closer approach to a boundary. The probe is robust and gives good reproducibility. It can be used for a wide range of pitch angle. Review of Scientific Instruments is copyrighted by The American Institute of Physics.

Fractional power dependence of rate on activation energy for reactions with very low internal barriers

The dynamics of reactions with low internal barriers are studied both analytically and numerically for two different models. Exact expressions for the average rate,kI, are obtained by solving the associated first passage time problems. Both the average rate constant, kI, and the numerically calculated long-time rate constant, kL, show a fractional power law dependence on the barrier height for very low barriers. The crossover of the reaction dynamics from low to high barrier is investigated.

Gudinski, by Stuart Coupe is a wild and fast ride

Review of Stuart Coupe's biography of Australian music legend Michael Gudinski.

Metal Auger intensity ratios as a probe for change-transfer effects in aluminum-covered transition metal

Marked changes in the LVV/LMV and LVV/LMM Auger intensity ratios of Co, Ni and Cu are observed on depositing Al on their surfaces. These changes, ascribed to charge-transfer or hybridization effects, are accompanied by changes in the intensity of the satellites next to the core levels of the transition metals.