Pore structure and column efficiency of silica monoliths in high performance liquid chromatography (HPLC)

Five different methods were critically examined to characterize the pore structure of the silica monoliths. The mesopore characterization was performed using: a) the classical BJH method of nitrogen sorption data, which showed overestimated values in the mesopore distribution and was improved by using the NLDFT method, b) the ISEC method implementing the PPM and PNM models, which were especially developed for monolithic silicas, that contrary to the particulate supports, demonstrate the two inflection points in the ISEC curve, enabling the calculation of pore connectivity, a measure for the mass transfer kinetics in the mesopore network, c) the mercury porosimetry using a new recommended mercury contact angle values. rnThe results of the characterization of mesopores of monolithic silica columns by the three methods indicated that all methods were useful with respect to the pore size distribution by volume, but only the ISEC method with implemented PPM and PNM models gave the average pore size and distribution based on the number average and the pore connectivity values.rnThe characterization of the flow-through pore was performed by two different methods: a) the mercury porosimetry, which was used not only for average flow-through pore value estimation, but also the assessment of entrapment. It was found that the mass transfer from the flow-through pores to mesopores was not hindered in case of small sized flow-through pores with a narrow distribution, b) the liquid penetration where the average flow-through pore values were obtained via existing equations and improved by the additional methods developed according to Hagen-Poiseuille rules. The result was that not the flow-through pore size influences the column bock pressure, but the surface area to volume ratio of silica skeleton is most decisive. Thus the monolith with lowest ratio values will be the most permeable. rnThe flow-through pore characterization results obtained by mercury porosimetry and liquid permeability were compared with the ones from imaging and image analysis. All named methods enable a reliable characterization of the flow-through pore diameters for the monolithic silica columns, but special care should be taken about the chosen theoretical model.rnThe measured pore characterization parameters were then linked with the mass transfer properties of monolithic silica columns. As indicated by the ISEC results, no restrictions in mass transfer resistance were noticed in mesopores due to their high connectivity. The mercury porosimetry results also gave evidence that no restrictions occur for mass transfer from flow-through pores to mesopores in the small scaled silica monoliths with narrow distribution. rnThe prediction of the optimum regimes of the pore structural parameters for the given target parameters in HPLC separations was performed. It was found that a low mass transfer resistance in the mesopore volume is achieved when the nominal diameter of the number average size distribution of the mesopores is appr. an order of magnitude larger that the molecular radius of the analyte. The effective diffusion coefficient of an analyte molecule in the mesopore volume is strongly dependent on the value of the nominal pore diameter of the number averaged pore size distribution. The mesopore size has to be adapted to the molecular size of the analyte, in particular for peptides and proteins. rnThe study on flow-through pores of silica monoliths demonstrated that the surface to volume of the skeletons ratio and external porosity are decisive for the column efficiency. The latter is independent from the flow-through pore diameter. The flow-through pore characteristics by direct and indirect approaches were assessed and theoretical column efficiency curves were derived. The study showed that next to the surface to volume ratio, the total porosity and its distribution of the flow-through pores and mesopores have a substantial effect on the column plate number, especially as the extent of adsorption increases. The column efficiency is increasing with decreasing flow through pore diameter, decreasing with external porosity, and increasing with total porosity. Though this tendency has a limit due to heterogeneity of the studied monolithic samples. We found that the maximum efficiency of the studied monolithic research columns could be reached at a skeleton diameter of ~ 0.5 µm. Furthermore when the intention is to maximize the column efficiency, more homogeneous monoliths should be prepared.rn

Proprietà morfologiche e strutturali di catalizzatori a base di Pt e Pd per la produzione di H2

In questo lavoro di tesi è stato affrontato uno studio mirato alla comprensione ed alla correlazione delle proprietà chimico-fisiche e morfologiche di catalizzatori a base di Pd/Pt supportati su allumina impiegati nella produzione di idrogeno mediante deidrogenazione di miscele complesse di idrocarburi contenenti elevati tenori di zolfo. La produzione di idrogeno mediante deidrogenazione parziale di fuel direttamente su aeromobili necessita di catalizzatori altamente performanti dei quali siano note tutte le caratteristiche in modo da prevedere, in un ampio margine di sicurezza, le possibili cause di malfunzionamento. L’applicabilità di materiali a base di Pd/Pt in questa reazione risiede nella loro capacità di resistere all’avvelenamento da zolfo, rivendicata in letteratura per reazioni di idrogenazione e della quale si sono trovate evidenze sperimentali in alcune prove preliminari svolte nello stesso ambito di ricerca. Le prove catalitiche hanno evidenziato che la deposizione su allumina dei due metalli in ragione di un rapporto molare Pd:Pt=2 con un carico di metalli complessivo del 2% in peso mostra i migliori risultati in termini di resistenza all’avvelenamento da zolfo e da deposizione di composti carboniosi.

Microscopia elettronica di nanoparticelle mg-pd e mg-ti per stoccaggio di idrogeno.

L'utilizzo dell'idrogeno come vettore energetico �è negli ultimi anni uno dei temi in maggior rilievo riguardo la sostenibilit�à energetica, questo per via della sua abbondanza in natura, della sua elevata energia chimica per unità di massa, e della non tossicità dei prodotti della sua combustione. Tuttavia non si conosce ancora una maniera e�fficiente di immagazzinarlo per poterlo utilizzare per applicazioni mobili. In questo lavoro di tesi sono state cresciute, e analizzate mediante microscopia elettronica, nanoparticelle di magnesio decorate con metalli di transizione (Pd e Ti), che si collocano tra i candidati più promettenti per lo stoccaggio di idrogeno a stato solido.

Sintesi e caratterizzazione di sistemi catalitici a base di pd-cu e loro utilizzo nella reazione di idrodeclorurazione di molecole clorofluorurate

Questo lavoro di tesi ha avuto come obiettivo quello di individuare e studiare diverse strategie di sintesi per la preparazione di catalizzatori a base di Pd-Cu supportati su materiali mesoporosi a basi di SiO2. Queste strategie sono state mirate a migliorare: -Distribuzione della fase metallica attiva e la sua accessibilità; -Formazione della fase mista Pd-Cu; -Dimensione delle specie metalliche sulla superficie; -Differenti caratteristiche morfologiche del supporto. I diversi catalizzatori preparati sono stati poi testati sulla reazione di idrodeclorurazione del 1,2-dicloro-1,1,2-trifluoro-2-(triflurometossi)etano (AM), svolta in fase gas con idrogeno a pressione atmosferica, con lo scopo di ottenere il composto insaturo corrispondente 1,1,2-trifluoro-2-(trifluorometossi)etene (MVE). Attualmente, il processo industriale per la produzione di MVE, è condotto con l’utilizzo di quantità stechiometriche di Zn in dimetilformammide; questo processo a causa delle quantità stechiometriche di ZnCl2 prodotto e dell'elevato consumo di solvente tossico risulta assai dispendioso dal punto di vista economico ed ambientale. La tipologia di materiali microporosi, già investigata, può limitare l'efficienza verso substrati ingombranti, è quindi interessante investigare catalizzatori con dimensione dei pori mesoporosi a base di silice; in particolare sono stati analizzati MCM-41 e silice amorfa GRACE® DAVICAT - 1401. In particolare, durante il lavoro di tesi sono stati sviluppati i seguenti argomenti: 1.Studio degli effetti della metodologia di sintesi e del contenuto metallico sui parametri chimico-fisici e catalitici dei sistemi a base di Pd-Cu supportati su MCM-41 e GRACE® DAVICAT - 1401; 2.Ottimizzazione del processo di sintesi dei supporti di MCM-41, ponendo attenzione alle quantità dei reagenti utilizzati, alla metodologia di eliminazione del templante e al tempo di trattamento idrotermale; 3.Ottimizzazione del processo di sintesi dei sistemi catalitici a base di Pd-Cu, al fine di ottenere una fase attiva costituita da particelle con dimensioni ridotte composte da una fase mista Pd-Cu.

Sviluppo di un sistema integrato innovativo per la contemporanea produzione e separazione di H2 ultrapuro, attraverso oxy-reforming, water-gas shift e membrane al Pd

Il presente lavoro di tesi si è focalizzato sullo studio e sulla ottimizzazione di un sistema integrato, che utilizzi la reazione di oxy-reforming del metano al fine di produrre syngas che venga trattato attraverso la water-gas shift al fine di abbattere il contenuto di CO e al tempo stesso aumentare la resa in H2. Con l’obiettivo di ottenere H2 ad elevata purezza (>99%) da poter essere inviato direttamente a celle a combustible ed in impianti di piccola taglia con possibile delocalizzazione della produzione industriale di energia elettrica e termica “pulita”, la miscela reale uscente dal processo di oxy-reforming è stata processata tramite successiva water-gas shift direttamente all’interno di una membrana ceramica al Pd selettiva nella separazione di H2. L’innovativià di questo progetto di studio è data da diversi parametri quali: 1) l’impiego dell’oxy-reforming in alternativa al normale steam-reforming del CH4, che permette di condurre il processo a temperature decisamente inferiori (700-750°C), utilizzando un minor quantitativo di vapore (S/C = 0.7); 2) l’utilizzo di due nuove formulazioni di catalizzatore di WGS per alte temperature, capace di operare in un unico stadio conversioni di CO ottenibili industrialmente solo attraverso i convenzionali due due stadi di reazione (e due diverse formulazioni di catalizzatori a base di Fe/Cr e Cu); 3) l’utilizzo di supporti ceramici con membrana a base di Pd, capaci di ospitare al loro interno un catalizzatore eterogeneo per la reazione di WGS a 400°C, rendendo quindi possibile la produzione e contemporanea separazione di H2 con un ulteriore effetto positivo poiché la membrana rimuovendo H2 dalla zona di reazione favorisce il superamento dell’equilibrio termodinamico per la conversione del CO, abbassandone il contenuto nel flusso uscente dei gas reazione e rendendo non più necessari sistemi aggiuntivi di separazione quali PSA o PROXY.

Effect of intravenous morphine comedication on bile duct visualization, diameter and volume applying intravenous CT cholangiography in a porcine liver model

To determine whether intravenous morphine comedication improves bile duct visualization, diameter and/or volume applying intravenous CT cholangiography in a porcine liver model.

Association of GWAS loci with PD in China

Genome-wide association studies (GWAS) have identified numerous single-nucleotide polymorphisms (SNPs) at four loci (SNCA, PARK16, LRRK2, BST1) that can modulate the risk of Parkinson's disease (PD). The strength of these associations has yet to be clarified in Mainland China. Ethnic specific effect is an important consideration in GWAS analysis. Using a case-control methodology, we genotyped multiple SNPs at these four loci to investigate their association with risk of PD in Mainland China. A total of 1,146 study subjects comprising 636 patients with PD and 510 unrelated healthy controls were recruited. The minor alleles at SNPs rs894278, rs1994090, rs2046932, rs4698412, and rs7304279 were found to be significantly higher in cases than in controls, while the minor alleles were found to significantly reduce the risk of developing PD at SNPs rs823128, rs823156, rs6532194, rs1191532, and rs16856139. These associations remained after taking into considerations the effects of age and gender. We showed that multiple SNPs at LRRK2 and SNCA increase risk of PD, while PARK16 SNPs are associated with a lower risk of PD in China. Our study findings will contribute to further research using GWAS-linked data and research on ethnic specific effect of common variants.

Angiographic maximal luminal diameter and appropriate deployment of the everolimus-eluting bioresorbable vascular scaffold as assessed by optical coherence tomography: an ABSORB cohort B trial sub-study

Bioresorbable vascular scaffolds (BVS) present different mechanical properties as compared to metallic platform stents. Therefore, the standard procedural technique to achieve appropriate deployment may differ.

Advanced morphological 3D magnetic resonance observation of cartilage repair tissue (MOCART) scoring using a new isotropic 3D proton-density, turbo spin echo sequence with variable flip angle distribution (PD-SPACE) compared to an isotropic 3D steady-state free precession sequence (True-FISP) and standard 2D sequences

To evaluate a new isotropic 3D proton-density, turbo-spin-echo sequence with variable flip-angle distribution (PD-SPACE) sequence compared to an isotropic 3D true-fast-imaging with steady-state-precession (True-FISP) sequence and 2D standard MR sequences with regard to the new 3D magnetic resonance observation of cartilage repair tissue (MOCART) score.

Vorsorglicher Rechtsschutz. Vorsorgliche Massnahmen im internationalen Kontext, offene Fragen im neuen Arrestrecht und Sicherungsmassnahmen der ZPO, mit Beiträgen von Dr. Isabelle Chabloz, Dr. Richard Gassmann, PD Dr. Pascal Grolimund, Dr. Jürg Roth, Prof. Dr. Daniel Staehelin

Am 9. September 2011 führte das Institut für Verfahrensrecht und Internationales Privatrecht (CIVPRO) der Universität Bern in bewährter Zusammenarbeit mit der schweizerischen SchKG-Vereinigung die zweite Schweizer Tagung für Internationales Zivilverfahrensrecht durch. Im Mittelpunkt der Tagung standen vorsorgliche Massnahmen im internationalen Kontext vor dem Hintergrund der neuesten Entwicklungen, namentlich (aber nicht nur) des neuen Lugano-Übereinkommens. Der Tagungsband enthält die auf den Vorträgen basierenden, überarbeiteten und erweiterten Beiträge namhafter Autorinnen und Autoren zum vorsorglichen Rechtsschutz im neuen IZPR (Pascal Grolimund). Besondere Aufmerksamkeit gilt dem neuen Arrestrecht sowohl im als auch ausserhalb des Anwendungsbereichs des Lugano-Übereinkommens (Richard Gassmann und Jürg Roth). Ebenso enthält der Band Beiträge zu den Sicherungsmassnahmen in der Realvollstreckung (Daniel Staehelin) sowie zur Anerkennung ausländischer vorsorglicher Massnahmen (Isabelle Chabloz).

A Double-Blind Randomized Controlled Trial (RCT) of Titanium-13Zirconium versus Titanium Grade IV Small-Diameter Bone Level Implants in Edentulous Mandibles - Results from a 1-Year Observation Period

Background: The use of endosseous dental implants has become common practice for the rehabilitation of edentulous patients, and a two-implant overdenture has been recommended as the standard of care. The use of small-diameter implants may extend treatment options and reduce the necessity for bone augmentation. However, the mechanical strength of titanium is limited, so titanium alloys with greater tensile and fatigue strength may be preferable. Purpose: This randomized, controlled, double-blind, multicenter study investigated in a split-mouth model whether small-diameter implants made from Titanium-13Zirconium alloy (TiZr, Roxolid™) perform at least as well as Titanium Grade IV implants. Methods and Materials: Patients with an edentulous mandible received one TiZr and one Ti Grade IV small-diameter bone level implant (3.3 mm, SLActive®) in the interforaminal region. The site distribution was randomized and double-blinded. Outcome measures included change in radiological peri-implant bone level from surgery to 12 months post-insertion (primary), implant survival, success, soft tissue conditions, and safety (secondary). Results: Of 91 treated patients, 87 were available for the 12-month follow-up. Peri-implant bone level change (-0.3 ± 0.5 mm vs -0.3 ± 0.6 mm), plaque, and sulcus bleeding indices were not significantly different between TiZr and Ti Grade IV implants. Implant survival rates were 98.9 percent and 97.8 percent, success rates were 96.6 percent and 94.4 percent, respectively. Nineteen minor and no serious adverse events were related to the study devices. Conclusion: This study confirms that TiZr small-diameter bone level implants provide at least the same outcomes after 12 months as Ti Grade IV bone level implants. The improved mechanical properties of TiZr implants may extend implant therapy to more challenging clinical situations.

Ketoprofen in piglets: enantioselective pharmacokinetics, pharmacodynamics and PK/PD modelling

The chiral pharmacokinetics and pharmacodynamics of ketoprofen were investigated in a placebo-controlled study in piglets after intramuscular administration of 6 mg/kg racemic ketoprofen. The absorption half-lives of both enantiomers were short, and S-ketoprofen predominated over R-ketoprofen in plasma. A kaolin-induced inflammation model was used to evaluate the anti-inflammatory, antipyretic and analgesic effects of ketoprofen. Skin temperatures increased after the kaolin injection, but the effect of ketoprofen was small. No significant antipyretic effects could be detected, but body temperatures tended to be lower in the ketoprofen-treated piglets. Mechanical nociceptive threshold testing was used to evaluate the analgesic effects. The piglets in the ketoprofen-treated group had significantly higher mechanical nociceptive thresholds compared to the piglets in the placebo group for 12-24 h following the treatment. Pharmacokinetic/pharmacodynamic modelling of the results from the mechanical nociceptive threshold testing gave a median IC(50) for S-ketoprofen of 26.7 mug/mL and an IC(50) for R-ketoprofen of 1.6 mug/mL. This indicates that R-ketoprofen is a more potent analgesic than S-ketoprofen in piglets. Estimated ED(50) for racemic ketoprofen was 2.5 mg/kg.

Distensibility and diameter of ascending aorta assessed by cardiac magnetic resonance imaging in adults with tetralogy of fallot or complete transposition

Structural abnormalities of the medial aorta have been described for conotruncal defects (e.g., tetralogy of Fallot [TOF] and complete transposition of the great arteries (dextrotransposition [d]-TGA). In TOF, progressive aortic dilation is a frequent finding. In patients with d-TGA with an atrial switch, this problem is less often described. The aim of the present study was to compare the extent of dilative aortopathy and aortic distensibility in adults with an atrial switch procedure (n = 39) to that in adults with repaired TOF (n = 39) and controls (n = 39), using cardiac magnetic resonance imaging. The groups were matched for age and gender. Diameters of the aorta indexed to the body surface area were significantly increased in the patients with d-TGA and TOF compared to that of the controls at the aortic sinus up to the level of the right pulmonary artery. On multivariate testing, the diagnosis of a conotruncal defect (β = 0.260; p = 0.003) and aortic regurgitant fraction (β = 0.405; p <0.001) were independent predictors of an increased aortic sinus diameter. Ascending aorta distensibility was significantly reduced in those with d-TGA and TOF compared to controls: 3.6 (interquartile range 1.5 to 4.4) versus 2.8 (interquartile range 2.0 to 3.7) versus 5.5 (interquartile range 4.8 to 6.9) ×10(-3) mm Hg(-1) (p <0.001). The independent predictors of ascending aorta distensibility were the diagnosis of a conotruncal defect (p <0.001) and age (p = 0.028). In conclusion, intrinsic aortopathy, manifested as increased ascending aortic diameters and reduced ascending aortic distensibility, is not only evident in adults with TOF, but also in adults with d-TGA and an atrial switch procedure. Long-term follow-up is needed to monitor the aortic size in both patient groups.