Refined second law of thermodynamics for fast random processes

We establish a refined version of the Second Law of Thermodynamics for Langevin stochastic processes describing mesoscopic systems driven by conservative or non-conservative forces and interacting with thermal noise. The refinement is based on the Monge-Kantorovich optimal mass transport and becomes relevant for processes far from quasi-stationary regime. General discussion is illustrated by numerical analysis of the optimal memory erasure protocol for a model for micron-size particle manipulated by optical tweezers.

First passages in bounded domains: When is the mean first passage time meaningful?

We study the first passage statistics to adsorbing boundaries of a Brownian motion in bounded two-dimensional domains of different shapes and configurations of the adsorbing and reflecting boundaries. From extensive numerical analysis we obtain the probability P(ω) distribution of the random variable ω=τ1/(τ1+τ2), which is a measure for how similar the first passage times τ1 and τ2 are of two independent realizations of a Brownian walk starting at the same location. We construct a chart for each domain, determining whether P(ω) represents a unimodal, bell-shaped form, or a bimodal, M-shaped behavior. While in the former case the mean first passage time (MFPT) is a valid characteristic of the first passage behavior, in the latter case it is an insufficient measure for the process. Strikingly we find a distinct turnover between the two modes of P(ω), characteristic for the domain shape and the respective location of absorbing and reflective boundaries. Our results demonstrate that large fluctuations of the first passage times may occur frequently in two-dimensional domains, rendering quite vague the general use of the MFPT as a robust measure of the actual behavior even in bounded domains, in which all moments of the first passage distribution exist.

Study of the temperature distribution in Si nanowires under microscopic laser beam excitation

The use of laser beams as excitation sources for the characterization of semiconductor nanowires (NWs) is largely extended. Raman spectroscopy and photoluminescence (PL) are currently applied to the study of NWs. However, NWs are systems with poor thermal conductivity and poor heat dissipation, which result in unintentional heating under the excitation with a focused laser beam with microscopic size, as those usually used in microRaman and microPL experiments. On the other hand, the NWs have subwavelength diameter, which changes the optical absorption with respect to the absorption in bulk materials. Furthermore, the NW diameter is smaller than the laser beam spot, which means that the optical power absorbed by the NW depends on its position inside the laser beam spot. A detailed analysis of the interaction between a microscopic focused laser beam and semiconductor NWs is necessary for the understanding of the experiments involving laser beam excitation of NWs. We present in this work a numerical analysis of the thermal transport in Si NWs, where the heat source is the laser energy locally absorbed by the NW. This analysis takes account of the optical absorption, the thermal conductivity, the dimensions, diameter and length of the NWs, and the immersion medium. Both free standing and heat-sunk NWs are considered. Also, the temperature distribution in ensembles of NWs is discussed. This analysis intends to constitute a tool for the understanding of the thermal phenomena induced by laser beams in semiconductor NWs.

A second order in time modified Lagrange-Galerkin finite element method for the incompressible Navier-Stokes equations

We introduce a second order in time modified Lagrange--Galerkin (MLG) method for the time dependent incompressible Navier--Stokes equations. The main ingredient of the new method is the scheme proposed to calculate in a more efficient manner the Galerkin projection of the functions transported along the characteristic curves of the transport operator. We present error estimates for velocity and pressure in the framework of mixed finite elements when either the mini-element or the $P2/P1$ Taylor--Hood element are used.

Computational Methods for Identification of Vibrating Structures

System identification deals with the problem of building mathematical models of dynamical systems based on observed data from the system" [1]. In the context of civil engineering, the system refers to a large scale structure such as a building, bridge, or an offshore structure, and identification mostly involves the determination of modal parameters (the natural frequencies, damping ratios, and mode shapes). This paper presents some modal identification results obtained using a state-of-the-art time domain system identification method (data-driven stochastic subspace algorithms [2]) applied to the output-only data measured in a steel arch bridge. First, a three dimensional finite element model was developed for the numerical analysis of the structure using ANSYS. Modal analysis was carried out and modal parameters were extracted in the frequency range of interest, 0-10 Hz. The results obtained from the finite element modal analysis were used to determine the location of the sensors. After that, ambient vibration tests were conducted during April 23-24, 2009. The response of the structure was measured using eight accelerometers. Two stations of three sensors were formed (triaxial stations). These sensors were held stationary for reference during the test. The two remaining sensors were placed at the different measurement points along the bridge deck, in which only vertical and transversal measurements were conducted (biaxial stations). Point estimate and interval estimate have been carried out in the state space model using these ambient vibration measurements. In the case of parametric models (like state space), the dynamic behaviour of a system is described using mathematical models. Then, mathematical relationships can be established between modal parameters and estimated point parameters (thus, it is common to use experimental modal analysis as a synonym for system identification). Stable modal parameters are found using a stabilization diagram. Furthermore, this paper proposes a method for assessing the precision of estimates of the parameters of state-space models (confidence interval). This approach employs the nonparametric bootstrap procedure [3] and is applied to subspace parameter estimation algorithm. Using bootstrap results, a plot similar to a stabilization diagram is developed. These graphics differentiate system modes from spurious noise modes for a given order system. Additionally, using the modal assurance criterion, the experimental modes obtained have been compared with those evaluated from a finite element analysis. A quite good agreement between numerical and experimental results is observed.

Method to analyze the influence of hysteresis in optical arithmetic units

A new method to analyze the influence of possible hysteresis cycles in devices employed for optical computing architectures is reported. A simple full adder structure is taken as the basis for this method. Single units, called optical programmable logic cells, previously reported by the authors, compose this structure. These cells employ, as basic devices, on-off and SEED-like components. Their hysteresis cycles have been modeled by numerical analysis. The influence of the different characteristic cycles is studied with respect to the obtained possible errors at the output. Two different approaches have been adopted. The first one shows the change in the arithmetic result output with respect to the different values and positions of the hysteresis cycle. The second one offers a similar result, but in a polar diagram where the total behavior of the system is better analyzed.

Slabsim: Simulador de dispositivos ópticos integrados

En los diseños y desarrollos de ingeniería, antes de comenzar la construcción e implementación de los objetivos de un proyecto, es necesario realizar una serie de análisis previos y simulaciones que corroboren las expectativas de la hipótesis inicial, con el fin de obtener una referencia empírica que satisfaga las condiciones de trabajo o funcionamiento de los objetivos de dicho proyecto. A menudo, los resultados que satisfacen las características deseadas se obtienen mediante la iteración de métodos de ensayo y error. Generalmente, éstos métodos utilizan el mismo procedimiento de análisis con la variación de una serie de parámetros que permiten adaptar una tecnología a la finalidad deseada. Hoy en día se dispone de computadoras potentes, así como algoritmos de resolución matemática que permiten resolver de forma veloz y eficiente diferentes tipos de problemas de cálculo. Resulta interesante el desarrollo de aplicaciones que permiten la resolución de éstos problemas de forma rápida y precisa en el análisis y síntesis de soluciones de ingeniería, especialmente cuando se tratan expresiones similares con variaciones de constantes, dado que se pueden desarrollar instrucciones de resolución con la capacidad de inserción de parámetros que definan el problema. Además, mediante la implementación de un código de acuerdo a la base teórica de una tecnología, se puede lograr un código válido para el estudio de cualquier problema relacionado con dicha tecnología. El desarrollo del presente proyecto pretende implementar la primera fase del simulador de dispositivos ópticos Slabsim, en cual se puede representar la distribución de la energía de una onda electromagnética en frecuencias ópticas guiada a través de una una guía dieléctrica plana, también conocida como slab. Este simulador esta constituido por una interfaz gráfica generada con el entorno de desarrollo de interfaces gráficas de usuario Matlab GUIDE, propiedad de Mathworks©, de forma que su manejo resulte sencillo e intuitivo para la ejecución de simulaciones con un bajo conocimiento de la base teórica de este tipo de estructuras por parte del usuario. De este modo se logra que el ingeniero requiera menor intervalo de tiempo para encontrar una solución que satisfaga los requisitos de un proyecto relacionado con las guías dieléctricas planas, e incluso utilizarlo para una amplia diversidad de objetivos basados en esta tecnología. Uno de los principales objetivos de este proyecto es la resolución de la base teórica de las guías slab a partir de métodos numéricos computacionales, cuyos procedimientos son extrapolables a otros problemas matemáticos y ofrecen al autor una contundente base conceptual de los mismos. Por este motivo, las resoluciones de las ecuaciones diferenciales y características que constituyen los problemas de este tipo de estructuras se realizan por estos medios de cálculo en el núcleo de la aplicación, dado que en algunos casos, no existe la alternativa de uso de expresiones analíticas útiles. ABSTRACT. The first step in engineering design and development is an analysis and simulation process which will successfully corroborate the initial hypothesis that was made and find solutions for a particular. In this way, it is possible to obtain empirical evidence which suitably substantiate the purposes of the project. Commonly, the characteristics to reach a particular target are found through iterative trial and error methods. These kinds of methods are based on the same theoretical analysis but with a variation of some parameters, with the objective to adapt the results for a particular aim. At present, powerful computers and mathematical algorithms are available to solve different kinds of calculation problems in a fast and efficient way. Computing application development is useful as it gives a high level of accurate results for engineering analysis and synthesis in short periods of time. This is more notable in cases where the mathematical expressions on a theoretical base are similar but with small variations of constant values. This is due to the ease of adaptation of the computer programming code into a parameter request system that defines a particular solution on each execution. Additionally, it is possible to code an application suitable to simulate any issue related to the studied technology. The aim of the present project consists of the construction of the first stage of an optoelectronics simulator named Slabsim. Slabism is capable of representing the energetic distribution of a light wave guided in the volume of a slab waveguide. The mentioned simulator is made through the graphic user interface development environment Matlab GUIDE, property of Mathworks©. It is designed for an easy and intuitive management by the user to execute simulations with a low knowledge of the technology theoretical bases. With this software it is possible to achieve several aims related to the slab waveguides by the user in low interval of time. One of the main purposes of this project is the mathematical solving of theoretical bases of slab structures through computing numerical analysis. This is due to the capability of adapting its criterion to other mathematical issues and provides a strong knowledge of its process. Based on these advantages, numerical solving methods are used in the core of the simulator to obtain differential and characteristic equations results that become represented on it.

Impedance of foundations using the Boundary Integral Equation Method

Dynamic soil-structure interaction has been for a long time one of the most fascinating areas for the engineering profession. The building of large alternating machines and their effects on surrounding structures as well as on their own functional behavior, provided the initial impetus; a large amount of experimental research was done,and the results of the Russian and German groups were especially worthwhile. Analytical results by Reissner and Sehkter were reexamined by Quinlan, Sung, et. al., and finally Veletsos presented the first set of reliable results. Since then, the modeling of the homogeneous, elastic halfspace as a equivalent set of springs and dashpots has become an everyday tool in soil engineering practice, especially after the appearance of the fast Fourier transportation algorithm, which makes possible the treatment of the frequency-dependent characteristics of the equivalent elements in a unified fashion with the general method of analysis of the structure. Extensions to the viscoelastic case, as well as to embedded foundations and complicated geometries, have been presented by various authors. In general, they used the finite element method with the well known problems of geometric truncations and the subsequent use of absorbing boundaries. The properties of boundary integral equation methods are, in our opinion, specially well suited to this problem, and several of the previous results have confirmed our opinion. In what follows we present the general features related to steady-state elastodynamics and a series of results showing the splendid results that the BIEM provided. Especially interesting are the outputs obtained through the use of the so-called singular elements, whose description is incorporated at the end of the paper. The reduction in time spent by the computer and the small number of elements needed to simulate realistically the global properties of the halfspace make this procedure one of the most interesting applications of the BIEM.

Vista general del modelado del sistema auditivo

El objetivo principal del presente proyecto es proporcionar al ingeniero de telecomunicaciones una visión general de las técnicas que se utilizan en el modelado del sistema auditivo. El modelado del sistema auditivo se realiza con los siguientes objetivos: a) Interpretar medidas directas, b)unificar el entendimiento de diferentes fenómenos, c) guiar estrategias de amplificación para suplir pérdidas auditivas y d) tener predicciones experimentalmente comprobables de comportamientos, con diferentes niveles de complejidad. En este trabajo se tratarán y explicarán brevemente las diferentes técnicas utilizadas para modelar las partes del sistema auditivo, desde las analogías electroacústicas, modelos biofísicos, binaurales, hasta la implementación de filtros auditivos mediante procesado de señal. Podemos concluir que el modelado mediante analogías electroacústicas permite una rápida implementación y entendimiento, pero tiene ciertas limitaciones. Las simulaciones mediante análisis numéricos son precisas y de gran utilidad tanto para del oído medio como para el interno. El procesado de señal es el procedimiento más completo y utilizado ya que permite modelar oído externo y medio además de permitir la implementación de filtros cocleares muy precisos y coherentes con la realidad incluyéndolos en modelos perceptivos. ABSTRACT. The main aim of the Project is to provide the Telecommunications Engineer an overview about the approaches for modelling the auditory system. The auditory system modelling is done for the next objectives: a) Interpret direct measures, b) Understand different phenomena c) get strategies of amplification for hearing impaired people and d) Obtain testable predictions experimentally about some behaviors with different complexity levels. Inside this document, several approaches about modeling of the auditory system parts will be explained: analog circuits, biophysics models, binaural models, and auditory filters made through signal processing. In conclusion, analog circuits are made quickly and they are easier to understand but they have many limitations. Simulations through numerical analysis are accurate and useful in middle and inner ear models. Signal processing is the more versatile approach because it lets to make a model of external and middle ear and then it allows to make complex auditory filters. Perceptive models can be made entirely through this method.

Análisis de micromovilidad en vástagos femorales mediante ensayo dinámico de oscilaciones libres

La artroplastia de cadera se considera uno de los mayores avances quirúrgicos de la Medicina. La aplicación de esta técnica de Traumatología se ha incrementado notablemente en los últimos anos, a causa principalmente del progresivo incremento de la esperanza de vida. En efecto, con la edad aumentan los problemas de artrosis y osteoporosis, enfermedades típicas de las articulaciones y de los huesos que requieren en muchos casos la sustitución protésica total o parcial de la articulación. El buen comportamiento funcional de una prótesis depende en gran medida de la estabilidad primaria, es decir, el correcto anclaje de la prótesis en el momento de su implantación. Las prótesis no cementadas basan su éxito a largo plazo en la osteointegración que tiene lugar entre el material protésico y el tejido óseo, y para lograrla es imprescindible conseguir unas buenas condiciones de estabilidad primaria. El aflojamiento aséptico es la principal causa de fallo de artroplastia total de cadera. Este es un fenómeno en el que, debido a complejas interacciones de factores mecánicos y biológicos, se producen movimientos relativos que comprometen la funcionalidad del implante. La minimización de los correspondientes danos depende en gran medida de la detección precoz del aflojamiento. Para lograr la detección temprana del aflojamiento aséptico del vástago femoral se han ensayado diferentes técnicas, tanto in vivo como in vitro: análisis numéricos y técnicas experimentales basadas en sensores de movimientos provocados por cargas transmitidas natural o artificialmente, tales como impactos o vibraciones de distintas frecuencias. Los montajes y procedimientos aplicados son heterogéneos y, en muchas ocasiones, complejos y costosos, no existiendo acuerdo sobre una técnica simple y eficaz de aplicación general. Asimismo, en la normativa vigente que regula las condiciones que debe cumplir una prótesis previamente a su comercialización, no hay ningún apartado referido específicamente a la evaluación de la bondad del diseño del vástago femoral con respecto a la estabilidad primaria. El objetivo de esta tesis es desarrollar una metodología para el análisis, in vitro, de la estabilidad de un vástago femoral implantado, a fin de poder evaluar las técnicas de implantación y los diferentes diseños de prótesis previamente a su oferta en el mercado. Además se plantea como requisito fundamental que el método desarrollado sea sencillo, reversible, repetible, no destructivo, con control riguroso de parámetros (condiciones de contorno de cargas y desplazamientos) y con un sistema de registro e interpretación de resultados rápido, fiable y asequible. Como paso previo, se ha realizado un análisis cualitativo del problema de contacto en la interfaz hueso-vástago aplicando una técnica optomecánica del campo continuo (fotoelasticidad). Para ello se han fabricado tres modelos en 2D del conjunto hueso-vástago, simulando tres tipos de contactos en la interfaz: contacto sin adherencia y con holgura, contacto sin adherencia y sin holgura, y contacto con adherencia y homogéneo. Aplicando la misma carga a cada modelo, y empleando la técnica de congelación de tensiones, se han visualizado los correspondientes estados tensionales, siendo estos más severos en el modelo de unión sin adherencia, como cabía esperar. En todo caso, los resultados son ilustrativos de la complejidad del problema de contacto y confirman la conveniencia y necesidad de la vía experimental para el estudio del problema. Seguidamente se ha planteado un ensayo dinámico de oscilaciones libres con instrumentación de sensores resistivos tipo galga extensométrica. Las muestras de ensayo han sido huesos fémur en todas sus posibles variantes: modelos simplificados, hueso sintético normalizado y hueso de cadáver, seco y fresco. Se ha diseñado un sistema de empotramiento del extremo distal de la muestra (fémur) con control riguroso de las condiciones de anclaje. La oscilación libre de la muestra se ha obtenido mediante la liberación instantánea de una carga estética determinada y aplicada previamente, bien con una maquina de ensayo o bien por gravedad. Cada muestra se ha instrumentado con galgas extensométricas convencionales cuya señal se ha registrado con un equipo dinámico comercial. Se ha aplicado un procedimiento de tratamiento de señal para acotar, filtrar y presentar las respuestas de los sensores en el dominio del tiempo y de la frecuencia. La interpretación de resultados es de tipo comparativo: se aplica el ensayo a una muestra de fémur Intacto que se toma de referencia, y a continuación se repite el ensayo sobre la misma muestra con una prótesis implantada; la comparación de resultados permite establecer conclusiones inmediatas sobre los efectos de la implantación de la prótesis. La implantación ha sido realizada por un cirujano traumatólogo utilizando las mismas técnicas e instrumental empleadas en el quirófano durante la práctica clínica real, y se ha trabajado con tres vástagos femorales comerciales. Con los resultados en el dominio del tiempo y de la frecuencia de las distintas aplicaciones se han establecido conclusiones sobre los siguientes aspectos: Viabilidad de los distintos tipos de muestras sintéticas: modelos simplificados y fémur sintético normalizado. Repetibilidad, linealidad y reversibilidad del ensayo. Congruencia de resultados con los valores teóricos deducidos de la teoría de oscilaciones libres de barras. Efectos de la implantación de tallos femorales en la amplitud de las oscilaciones, amortiguamiento y frecuencias de oscilación. Detección de armónicos asociados a la micromovilidad. La metodología se ha demostrado apta para ser incorporada a la normativa de prótesis, es de aplicación universal y abre vías para el análisis de la detección y caracterización de la micromovilidad de una prótesis frente a las cargas de servicio. ABSTRACT Total hip arthroplasty is considered as one of the greatest surgical advances in medicine. The application of this technique on Traumatology has increased significantly in recent years, mainly due to the progressive increase in life expectancy. In fact, advanced age increases osteoarthritis and osteoporosis problems, which are typical diseases of joints and bones, and in many cases require full or partial prosthetic replacement on the joint. Right functional behavior of prosthesis is highly dependent on the primary stability; this means it depends on the correct anchoring of the prosthesis at the time of implantation. Uncemented prosthesis base their long-term success on the quality of osseointegration that takes place between the prosthetic material and bone tissue, and to achieve this good primary stability conditions is mandatory. Aseptic loosening is the main cause of failure in total hip arthroplasty. This is a phenomenon in which relative movements occur, due to complex interactions of mechanical and biological factors, and these micromovements put the implant functionality at risk. To minimize possible damage, it greatly depends on the early detection of loosening. For this purpose, various techniques have been tested both in vivo and in vitro: numerical analysis and experimental techniques based on sensors for movements caused by naturally or artificially transmitted loads, such as impacts or vibrations at different frequencies. The assemblies and methods applied are heterogeneous and, in many cases, they are complex and expensive, with no agreement on the use of a simple and effective technique for general purposes. Likewise, in current regulations for governing the conditions to be fulfilled by the prosthesis before going to market, there is no specific section related to the evaluation of the femoral stem design in relation to primary stability. The aim of this thesis is to develop a in vitro methodology for analyzing the stability of an implanted femoral stem, in order to assess the implantation techniques and the different prosthesis designs prior to its offer in the market. We also propose as a fundamental requirement that the developed testing method should be simple, reversible, repeatable, non-destructive, with close monitoring of parameters (boundary conditions of loads and displacements) and with the availability of a register system to record and interpret results in a fast, reliable and affordable manner. As a preliminary step, we have performed a qualitative analysis of the contact problems in the bone-stem interface, through the application of a continuous field optomechanical technique (photoelasticity). For this proposal three 2D models of bone–stem set, has been built simulating three interface contact types: loosened an unbounded contact, unbounded and fixed contact, and bounded homogeneous contact. By means of applying the same load to each model, and using the stress freezing technique, it has displayed the corresponding stress states, being more severe as expected, in the unbounded union model. In any case, the results clearly show the complexity of the interface contact problem, and they confirm the need for experimental studies about this problem. Afterward a free oscillation dynamic test has been done using resistive strain gauge sensors. Test samples have been femur bones in all possible variants: simplified models, standardized synthetic bone, and dry and cool cadaveric bones. An embedding system at the distal end of the sample with strong control of the anchoring conditions has been designed. The free oscillation of the sample has been obtained by the instantaneous release of a static load, which was previously determined and applied to the sample through a testing machine or using the gravity force. Each sample was equipped with conventional strain gauges whose signal is registered with a marketed dynamic equipment. Then, it has applied a signal processing procedure to delimit, filter and present the time and frequency response signals from the sensors. Results are interpreted by comparing different trials: the test is applied to an intact femur sample which is taken as a reference, and then this test is repeated over the same sample with an implanted prosthesis. From comparison between results, immediate conclusions about the effects of the implantation of the prosthesis can be obtained. It must be said that the implementation has been made by an expert orthopedic surgeon using the same techniques and instruments as those used in clinical surgery. He has worked with three commercial femoral stems. From the results obtained in the time and frequency domains for the different applications the following conclusions have been established: Feasibility of the different types of synthetic samples: simplified models and standardized synthetic femur. Repeatability, linearity and reversibility of the testing method. Consistency of results with theoretical values deduced from the bars free oscillations theory. Effects of introduction of femoral stems in the amplitude, damping and frequencies of oscillations Detection of micromobility associated harmonics. This methodology has been proved suitable to be included in the standardization process of arthroplasty prosthesis, it is universally applicable and it allows establishing new methods for the analysis, detection and characterization of prosthesis micromobility due to functional loads.

Survival probability of round and tape tethers against debris impact

The current space environment, consisting of manmade debris and micrometeoroids, poses a risk to safe operations in space, and the situation is continuously deteriorating due to in-orbit debris collisions and to new satellite launches. Bare electrodynamic tethers can provide an efficient mechanism for rapid deorbiting of satellites from low Earth orbit at end of life. Because of its particular geometry (length very much larger than cross-sectional dimensions), a tether may have a relatively high risk of being severed by the single impact of small debris. The rates of fatal impact of orbital debris on round and tape tethers of equal length and mass, evaluated with an analytical approximation to debris flux modeled by NASA’s ORDEM2000, shows much higher survival probability for tapes. A comparative numerical analysis using debris flux model ORDEM2000 and ESA’s MASTER2005 validates the analytical result and shows that, for a given time in orbit, a tape has a probability of survival of about one and a half orders of magnitude higher than a round tether of equal mass and length. Because deorbiting from a given altitude is much faster for the tape due to its larger perimeter, its probability of survival in a practical sense is quite high.

Behaviour of Concrete Structural Members Subjected to Air Blast Loading

Numerical analysis is a suitable tool in the design of complex reinforced concrete structures under extreme impulsive loadings such as impacts or explosions at close range. Such events may be the result of terrorist attacks. Reinforced concrete is commonly used for buildings and infrastructures. For this reason, the ability to accurately run numerical simulations of concrete elements subjected to blast loading is needed. In this context, reliable constitutive models for concrete are of capital importance. In this research numerical simulations using two different constitutive models for concrete (Continuous Surface Cap Model and Brittle Damage Model) have been carried out using LS-DYNA. Two experimental benchmark tests have been taken as reference. The results of the numerical simulations with the aforementioned constitutive models show different abilities to accurately represent the structural response of the reinforced concrete elements studied.

Chaos in non lineal Alfven waves using the DNLS equations

The electro-dynamical tethers emit waves in structured denominated Alfven wings. The Derivative Nonlineal Schrödinger Equation (DNLS) possesses the capacity to describe the propagation of circularly polarized Alfven waves of finite amplitude in cold plasmas. The DNLS equation is truncated to explore the coherent, weakly nonlinear, cubic coupling of three waves near resonance, one wave being linearly unstable and the other waves damped. In this article is presented a theoretical and numerical analysis when the growth rate of the unstable wave is next to zero considering two damping models: Landau and resistive. The DNLS equation presents a chaotic dynamics when is consider only three wave truncation. The evolution to chaos possesses three routes: hard transition, period-doubling and intermittence of type I.

Técnicas avanzadas de metrología dimensional indirecta mediante el empleo de máquinas de medición por visión en entornos industriales. Modelo para la estimación de incertidumbres

Esta tesis contiene una investigación detallada sobre las características y funcionamiento de las máquinas de medición por visión. El objetivo fundamental es modelar su comportamiento y dotarlas de trazabilidad metrológica bajo cualquier condición de medida. Al efecto, se ha realizado un exhaustivo análisis de los elementos que conforman su cadena de medición, a saber: sistema de iluminación, estructura, lentes y objetivos, cámara, software de tratamiento de imágenes y software de cálculo. Se han definido modelos físico-matemáticos, de desarrollo propio, capaces de simular con fiabilidad el comportamiento de los elementos citados, agrupados, a efectos de análisis numérico, en dos subsistemas denominados: de visión y mecánico. Se han implementado procedimientos de calibración genuinos para ambos subsistemas mediante el empleo de patrones ópticos. En todos los casos se ha podido determinar la incertidumbre asociada a los diferentes parámetros involucrados, garantizando la trazabilidad metrológica de los resultados. Los distintos modelos desarrollados han sido implementados en Matlab®. Se ha verificado su validez empleando valores sintéticos obtenidos a partir de simulaciones informáticas y también con imágenes reales capturadas en el laboratorio. El estudio experimental y validación definitiva de los resultados se ha realizado en el Laboratorio de Longitud del Centro Español de Metrología y en el Laboratorio de Metrología Dimensional de la ETS de Ingeniería y Diseño Industrial de la UPM. Los modelos desarrollados se han aplicado a dos máquinas de medición por visión de diferentes características constructivas y metrológicas. Empleando dichas máquinas se han medido distintas piezas, pertenecientes a los ámbitos mecánico y oftalmológico. Los resultados obtenidos han permitido la completa caracterización dimensional de dichas piezas y la determinación del cumplimiento de las especificaciones metrológicas en todos los casos, incluyendo longitudes, formas y ángulos. ABSTRACT This PhD thesis contains a detailed investigation of characteristics and performance of the optical coordinate measurement machines. The main goal is to model their behaviour and provide metrological traceability to them under any measurement conditions. In fact, a thorough analysis of the elements which form the measuring chain, i.e.: lighting system, structure, lenses and objectives, camera, image processing software and coordinate metrology software has conducted. Physical-mathematical models, of self-developed, able to simulate with reliability the behavior of the above elements, grouped, for the purpose of numerical analysis, in two subsystems called: “vision subsystem” and “mechanical subsystem”, have been defined. Genuine calibration procedures for both subsystems have been implemented by use of optical standards. In all cases, it has been possible to determine the uncertainty associated with the different parameters involved, ensuring metrological traceability of results. Different developed models have been implemented in Matlab®. Their validity has been verified using synthetic values obtained from computer simulations and also with real images captured in laboratory. The experimental study and final validation of the results was carried out in the Length Laboratory of “Centro Español de Metrología” and Dimensional Metrology Laboratory of the “Escuela Técnica Superior de Ingeniería y Diseño Industrial” of the UPM. The developed models have been applied to two optical coordinate measurement machines with different construction and metrological characteristics. Using such machines, different parts, belonging to the mechanical and ophthalmologist areas, have been measured. The obtained results allow the full dimensional characterization of such parts and determination of compliance with metrological specifications in all cases, including lengths, shapes and angles.

Bare-tape scaling laws for de-orbit missions in a space debris environment

El entorno espacial actual hay un gran numero de micro-meteoritos y basura espacial generada por el hombre, lo cual plantea un riesgo para la seguridad de las operaciones en el espacio. La situación se agrava continuamente a causa de las colisiones de basura espacial en órbita, y los nuevos lanzamientos de satélites. Una parte significativa de esta basura son satélites muertos, y fragmentos de satélites resultantes de explosiones y colisiones de objetos en órbita. La mitigación de este problema se ha convertido en un tema de preocupación prioritario para todas las instituciones que participan en operaciones espaciales. Entre las soluciones existentes, las amarras electrodinámicas (EDT) proporcionan un eficiente dispositivo para el rápido de-orbitado de los satélites en órbita terrestre baja (LEO), al final de su vida útil. El campo de investigación de las amarras electrodinámicas (EDT) ha sido muy fructífero desde los años 70. Gracias a estudios teóricos, y a misiones para la demostración del funcionamiento de las amarras en órbita, esta tecnología se ha desarrollado muy rápidamente en las últimas décadas. Durante este período de investigación, se han identificado y superado múltiples problemas técnicos de diversa índole. Gran parte del funcionamiento básico del sistema EDT depende de su capacidad de supervivencia ante los micro-meteoritos y la basura espacial. Una amarra puede ser cortada completamente por una partícula cuando ésta tiene un diámetro mínimo. En caso de corte debido al impacto de partículas, una amarra en sí misma, podría ser un riesgo para otros satélites en funcionamiento. Por desgracia, tras varias demostraciones en órbita, no se ha podido concluir que este problema sea importante para el funcionamiento del sistema. En esta tesis, se presenta un análisis teórico de la capacidad de supervivencia de las amarras en el espacio. Este estudio demuestra las ventajas de las amarras de sección rectangular (cinta), en cuanto a la probabilidad de supervivencia durante la misión, frente a las amarras convencionales (cables de sección circular). Debido a su particular geometría (longitud mucho mayor que la sección transversal), una amarra puede tener un riesgo relativamente alto de ser cortado por un único impacto con una partícula de pequeñas dimensiones. Un cálculo analítico de la tasa de impactos fatales para una amarra cilindrica y de tipo cinta de igual longitud y masa, considerando el flujo de partículas de basura espacial del modelo ORDEM2000 de la NASA, muestra mayor probabilidad de supervivencia para las cintas. Dicho análisis ha sido comparado con un cálculo numérico empleando los modelos de flujo el ORDEM2000 y el MASTER2005 de ESA. Además se muestra que, para igual tiempo en órbita, una cinta tiene una probabilidad de supervivencia un orden y medio de magnitud mayor que una amarra cilindrica con igual masa y longitud. Por otra parte, de-orbitar una cinta desde una cierta altitud, es mucho más rápido, debido a su mayor perímetro que le permite capturar más corriente. Este es un factor adicional que incrementa la probabilidad de supervivencia de la cinta, al estar menos tiempo expuesta a los posibles impactos de basura espacial. Por este motivo, se puede afirmar finalmente y en sentido práctico, que la capacidad de supervivencia de la cinta es bastante alta, en comparación con la de la amarra cilindrica. El segundo objetivo de este trabajo, consiste en la elaboración de un modelo analítico, mejorando la aproximación del flujo de ORDEM2000 y MASTER2009, que permite calcular con precisión, la tasa de impacto fatal al año para una cinta en un rango de altitudes e inclinaciones, en lugar de unas condiciones particulares. Se obtiene el numero de corte por un cierto tiempo en función de la geometría de la cinta y propiedades de la órbita. Para las mismas condiciones, el modelo analítico, se compara con los resultados obtenidos del análisis numérico. Este modelo escalable ha sido esencial para la optimización del diseño de la amarra para las misiones de de-orbitado de los satélites, variando la masa del satélite y la altitud inicial de la órbita. El modelo de supervivencia se ha utilizado para construir una función objetivo con el fin de optimizar el diseño de amarras. La función objectivo es el producto del cociente entre la masa de la amarra y la del satélite y el numero de corte por un cierto tiempo. Combinando el modelo de supervivencia con una ecuación dinámica de la amarra donde aparece la fuerza de Lorentz, se elimina el tiempo y se escribe la función objetivo como función de la geometría de la cinta y las propietades de la órbita. Este modelo de optimización, condujo al desarrollo de un software, que esta en proceso de registro por parte de la UPM. La etapa final de este estudio, consiste en la estimación del número de impactos fatales, en una cinta, utilizando por primera vez una ecuación de límite balístico experimental. Esta ecuación ha sido desarollada para cintas, y permite representar los efectos tanto de la velocidad de impacto como el ángulo de impacto. Los resultados obtenidos demuestran que la cinta es altamente resistente a los impactos de basura espacial, y para una cinta con una sección transversal definida, el número de impactos críticos debidos a partículas no rastreables es significativamente menor. ABSTRACT The current space environment, consisting of man-made debris and tiny meteoroids, poses a risk to safe operations in space, and the situation is continuously deteriorating due to in-orbit debris collisions and to new satellite launches. Among these debris a significant portion is due to dead satellites and fragments of satellites resulted from explosions and in-orbit collisions. Mitigation of space debris has become an issue of first concern for all the institutions involved in space operations. Bare electrodynamic tethers (EDT) can provide an efficient mechanism for rapid de-orbiting of defunct satellites from low Earth orbit (LEO) at end of life. The research on EDT has been a fruitful field since the 70’s. Thanks to both theoretical studies and in orbit demonstration missions, this technology has been developed very fast in the following decades. During this period, several technical issues were identified and overcome. The core functionality of EDT system greatly depends on their survivability to the micrometeoroids and orbital debris, and a tether can become itself a kind of debris for other operating satellites in case of cutoff due to particle impact; however, this very issue is still inconclusive and conflicting after having a number of space demonstrations. A tether can be completely cut by debris having some minimal diameter. This thesis presents a theoretical analysis of the survivability of tethers in space. The study demonstrates the advantages of tape tethers over conventional round wires particularly on the survivability during the mission. Because of its particular geometry (length very much larger than cross-sectional dimensions), a tether may have a relatively high risk of being severed by the single impact of small debris. As a first approach to the problem, survival probability has been compared for a round and a tape tether of equal mass and length. The rates of fatal impact of orbital debris on round and tape tether, evaluated with an analytical approximation to debris flux modeled by NASA’s ORDEM2000, shows much higher survival probability for tapes. A comparative numerical analysis using debris flux model ORDEM2000 and ESA’s MASTER2005 shows good agreement with the analytical result. It also shows that, for a given time in orbit, a tape has a probability of survival of about one and a half orders of magnitude higher than a round tether of equal mass and length. Because de-orbiting from a given altitude is much faster for the tape due to its larger perimeter, its probability of survival in a practical sense is quite high. As the next step, an analytical model derived in this work allows to calculate accurately the fatal impact rate per year for a tape tether. The model uses power laws for debris-size ranges, in both ORDEM2000 and MASTER2009 debris flux models, to calculate tape tether survivability at different LEO altitudes. The analytical model, which depends on tape dimensions (width, thickness) and orbital parameters (inclinations, altitudes) is then compared with fully numerical results for different orbit inclinations, altitudes and tape width for both ORDEM2000 and MASTER2009 flux data. This scalable model not only estimates the fatal impact count but has proved essential in optimizing tether design for satellite de-orbit missions varying satellite mass and initial orbital altitude and inclination. Within the frame of this dissertation, a simple analysis has been finally presented, showing the scalable property of tape tether, thanks to the survivability model developed, that allows analyze and compare de-orbit performance for a large range of satellite mass and orbit properties. The work explicitly shows the product of tether-to-satellite mass-ratio and fatal impact count as a function of tether geometry and orbital parameters. Combining the tether dynamic equation involving Lorentz drag with space debris impact survivability model, eliminates time from the expression. Hence the product, is independent of tether de-orbit history and just depends on mission constraints and tether length, width and thickness. This optimization model finally led to the development of a friendly software tool named BETsMA, currently in process of registration by UPM. For the final step, an estimation of fatal impact rate on a tape tether has been done, using for the first time an experimental ballistic limit equation that was derived for tapes and accounts for the effects of both the impact velocity and impact angle. It is shown that tape tethers are highly resistant to space debris impacts and considering a tape tether with a defined cross section, the number of critical events due to impact with non-trackable debris is always significantly low.