Water-assisted Flow of Heavy Oil in a Vertical Pipe: Pilot-scale Experiments

The use of the core-annular flow pattern, where a thin fluid surrounds a very viscous one, has been suggested as an attractive artificial-lift method for heavy oils in the current Brazilian ultra-deepwater production scenario. This paper reports the pressure drop measurements and the core-annular flow observed in a 2 7/8-inch and 300 meter deep pilot-scale well conveying a mixture of heavy crude oil (2000 mPa.s and 950 kg/m3 at 35 C) and water at several combinations of the individual flow rates. The two-phase pressure drop data are compared with those of single-phase oil flow to assess the gains due to water injection. Another issue is the handling of the core-annular flow once it has been established. High-frequency pressure-gradient signals were collected and a treatment based on the Gabor transform together with neural networks is proposed as a promising solution for monitoring and control. The preliminary results are encouraging. The pilot-scale tests, including long-term experiments, were conducted in order to investigate the applicability of using water to transport heavy oils in actual wells. It represents an important step towards the full scale application of the proposed artificial-lift technology. The registered improvements in terms of oil production rate and pressure drop reductions are remarkable.

Expanding the horizontal capabilities of CRT monitors using artificial inter-pixel steps for neuroscience experiments

This article describes the development of a visual stimulus generator to be used in neuroscience experiments with invertebrates such as flies. The experiment consists in the visualization of a fixed image that is displaced horizontally according to the stimulus data. The system is capable of displaying 640 x 480 pixels with 256 intensity levels at 200 frames per second (FPS) on conventional raster monitors. To double the possible horizontal positioning possibilities from 640 to 1280, a novel technique is presented introducing artificial inter-pixel steps. The implementation consists in using two video frame buffers containing each a distinct view of the desired image pattern. This implementation generates a visual effect capable of doubling the horizontal positioning capabilities of the visual stimulus generator allowing more precise and movements more contiguous. (C) 2011 Elsevier Inc. All rights reserved.

Recoupled separated-local-field experiments and applications to study intermediate-regime molecular motions

A specific separated-local-field NMR experiment, dubbed Dipolar-Chemical-Shift Correlation (DIPSHIFT) is frequently used to study molecular motions by probing reorientations through the changes in XH dipolar coupling and T-2. In systems where the coupling is weak or the reorientation angle is small, a recoupled variant of the DIPSHIFT experiment is applied, where the effective dipolar coupling is amplified by a REDOR-like pi-pulse train. However, a previously described constant-time variant of this experiment is not sensitive to the motion-induced T-2 effect, which precludes the observation of motions over a large range of rates ranging from hundreds of Hz to around a MHz. We present a DIPSHIFT implementation which amplifies the dipolar couplings and is still sensitive to T-2 effects. Spin dynamics simulations, analytical calculations and experiments demonstrate the sensitivity of the technique to molecular motions, and suggest the best experimental conditions to avoid imperfections. Furthermore, an in-depth theoretical analysis of the interplay of REDOR-like recoupling and proton decoupling based on Average-Hamiltonian Theory was performed, which allowed explaining the origin of many artifacts found in literature data. (C) 2012 Elsevier Inc. All rights reserved.

Applying design of experiments (DOE) to flavonoid extraction from Passiflora alata and P. edulis

The Passifloraceae family is extensively used in native Brazilian folk medicine to treat a wide variety of diseases. The problem of flavonoid extraction from Passiflora was treated by application of design of experiments (DOE), as an experiment with mixture including one categorical process variable. The components of the binary mixture were: ethanol (component A) and water (component B); the categorical process variable: extraction method (factor C) was varied at two levels: (+1) maceration and (-1) percolation. ANOVA suggested a cubic model for P. edulis extraction and a quadratic model for P. alata.These results indicate that the proportion of components A and B in the mixture is the main factor involved in significantly increasing flavonoid extraction. In regard to the extraction methods, no important differences were observed, which indicates that these two traditional extraction methods could be effectively used to extract flavonoids from both medicinal plants. The evaluation of antioxidant activity of the extract by ORAC method showed that P. edulis displays twice as much antioxidant activity as P. alata. Considering that maceration is a simple, rapid and environmentally friendly extraction method, in this study, the optimized conditions for flavonoid extraction from these Passiflora species is maceration with 75% ethanol for P. edulis and 50% ethanol for P. alata.

Fatigue crack growth assessments in welded components including crack closure effects: Experiments and 3-D numerical modeling

This work provides a numerical and experimental investigation of fatigue crack growth behavior in steel weldments including crack closure effects and their coupled interaction with weld strength mismatch. A central objective of this study is to extend previously developed frameworks for evaluation of crack clo- sure effects on FCGR to steel weldments while, at the same time, gaining additional understanding of commonly adopted criteria for crack closure loads and their influence on fatigue life of structural welds. Very detailed non-linear finite element analyses using 3-D models of compact tension C ( T ) fracture spec- imens with center cracked, square groove welds provide the evolution of crack growth with cyclic stress intensity factor which is required for the estimation of the closure loads. Fatigue crack growth tests con- ducted on plane-sided, shallow-cracked C ( T ) specimens provide the necessary data against which crack closure effects on fatigue crack growth behavior can be assessed. Overall, the present investigation pro- vides additional support for estimation procedures of plasticity-induced crack closure loads in fatigue analyses of structural steels and their weldments

One and two degrees-of-freedom Vortex-Induced Vibration experiments with yawed cylinders

Vortex-Induced Vibration (VIV) experiments were carried out with yawed cylinders. The purpose was to investigate the validity of the Independence Principle (IP) for properly describing the flow characteristics and the dynamics of structures subjected to oblique flow. Five yaw angles in relation to the direction perpendicular to the free stream velocity were tested, namely View the MathML sourceθ=0°,10°,20°,30° and 45°. Both the upstream and downstream orientations were tested. The models were mounted on a leaf spring apparatus that allows experiments with one or two degrees of freedom. The Reynolds numbers based on the component normal to the cylinder axis fell in the interval 3×103experiments. Time histories of displacement and hydrodynamic forces were acquired. Considering only the component of the free stream which is normal to the cylinder axis, the results of amplitude and force coefficients agreed reasonably well with the non-yawed ones for yaw angles up to 20° for both one and two degrees-of-freedom experiments. This indicates the validity of the IP for this yaw angle range. For yaw angles larger than 20°, a decrease in the maximum amplitude was observed. The decrease in the oscillation amplitudes was related to a larger modulation in the phase shift between force and displacement. Differences in the results for upstream and downstream were observed and were more evident for the larger yaw angle. These differences can be associated to the asymmetric cylinder end conditions.

In-situ XANES experiments on Ni K-edge in mesoporous ZrO2-CeO2:Ni.

Ordered mesoporous ZrO2-CeO2 mixed oxides are potential candidates for catalytic applications. These systems, used as anodes in solid oxide fuel cells (SOFC), may lead to better performance of SOFCs, due to an enhancement on surface area, aiming to achieve a lower working temperature. The aim of this studies is to evaluate the reduction capacity of Ni2+ to Ni in ZrO2-x(mol)%CeO2 (x=50 and 90) samples impregnated with 60(wt.)%NiO. The synthesis was made with Zr and Ce chloride precursors, HCl aqueous solution, Pluronic P123, NH4OH to adjust the pH (3-4) and a teflon autoclave to perform a hydrothermal treatment (80oC/48h). The samples were dried and calcined, until 540oC in N2 and 4 hours in air. The NiO impregnation was made with an ethanol dispersion of Ni(NO3)£6H2O. The powder was calcinated in air until 350oC for 2 hours. Temperature-resolved XANES data at the Ni K-edge were collected at the DXAS beam line of the LNLS in transmission mode, using a Si(111) monochromator and a CCD detector. Sample preparation consisted of mixing »6mg of the powder samples with boron nitride and pressing into pellets. The data were acquired during an experiment of temperature programmed reduction (TPR) under a 5% H2/He until 600oC and mixtures of 20%CH4:5%O2/He, at temperatures from 400 to 600oC. All the reactions were monitored with a mass spectrometer. The data was analyzed with a linear combination fit of 2 standards for each valence number using Athena software. The Ni K-edge experiments demonstrated that for both contents of CeO2, NiO embedded in the porous zirconia-ceria matrix reduces at lower temperatures than pure NiO, revealing that the ZrO2-CeO2 support improves the reduction of impregnated NiO. Ni was oxidized to NiO after all reactions with methane and oxygen. Hydrogenated carbonaceous species were detected, but under reducing conditions, the hydrocarbon compounds are removed. The reaction of total oxidation of methane CH4:O2 (1:2 ratio) was observed at lower temperatures (around 400oC) for both samples.

Hands-on experiments in the Practicum: repositioning student teachers' autonomy.

Following a worldwide trend, the Initial Teacher Education (ITE) Programmes in Brazil are recently searching for ways of integrating practice into curriculum. It raises question about what practice must be integrated and how. Notably, university-based courses are disconnected from school and have low commitment with school issues (Zeichner, 2009).The student teacher induction into school daily life is not an easy task, mainly when the practitioners are transforming physics classroom practice toward an active learning. Drawing on cultural-historical framework (Wolff-Michael Roth & Lee, 2007; Vygotsky, 1978) this study addresses the articulation between Practicum in Physics Classes and the Hands-on Experiments (HoE) used throughout the Practicum. Although in a different level, both Practicum and HoE are linked with an idea of practice. Particularly, this study focuses on how HoE might foster student teachers' autonomy and agency in the Practicum. Data was gathered in the course Practice of Physics Teaching at University of São Paulo/Brazil in 2010; in a cohort of 60 student teachers doing a year-long Practicum in urban school in São Paulo city. Data was analysed using qualitative research methods (Roth, 2005), based on 14 interviews and video records of the student teacher preparing the HoE for Practicum we will present in general lines the role of HoE for student teacher autonomy.

Bottle effects, toxicity and cell viability during incubation experiments to asses community respiration

Máster en Oceanografía

Applications of High Speed Configurable Logic Devices in Modern Particle Physics Experiments

Several activities were conducted during my PhD activity. For the NEMO experiment a collaboration between the INFN/University groups of Catania and Bologna led to the development and production of a mixed signal acquisition board for the Nemo Km3 telescope. The research concerned the feasibility study for a different acquisition technique quite far from that adopted in the NEMO Phase 1 telescope. The DAQ board that we realized exploits the LIRA06 front-end chip for the analog acquisition of anodic an dynodic sources of a PMT (Photo-Multiplier Tube). The low-power analog acquisition allows to sample contemporaneously multiple channels of the PMT at different gain factors in order to increase the signal response linearity over a wider dynamic range. Also the auto triggering and self-event-classification features help to improve the acquisition performance and the knowledge on the neutrino event. A fully functional interface towards the first level data concentrator, the Floor Control Module, has been integrated as well on the board, and a specific firmware has been realized to comply with the present communication protocols. This stage of the project foresees the use of an FPGA, a high speed configurable device, to provide the board with a flexible digital logic control core. After the validation of the whole front-end architecture this feature would be probably integrated in a common mixed-signal ASIC (Application Specific Integrated Circuit). The volatile nature of the configuration memory of the FPGA implied the integration of a flash ISP (In System Programming) memory and a smart architecture for a safe remote reconfiguration of it. All the integrated features of the board have been tested. At the Catania laboratory the behavior of the LIRA chip has been investigated in the digital environment of the DAQ board and we succeeded in driving the acquisition with the FPGA. The PMT pulses generated with an arbitrary waveform generator were correctly triggered and acquired by the analog chip, and successively they were digitized by the on board ADC under the supervision of the FPGA. For the communication towards the data concentrator a test bench has been realized in Bologna where, thanks to a lending of the Roma University and INFN, a full readout chain equivalent to that present in the NEMO phase-1 was installed. These tests showed a good behavior of the digital electronic that was able to receive and to execute command imparted by the PC console and to answer back with a reply. The remotely configurable logic behaved well too and demonstrated, at least in principle, the validity of this technique. A new prototype board is now under development at the Catania laboratory as an evolution of the one described above. This board is going to be deployed within the NEMO Phase-2 tower in one of its floors dedicated to new front-end proposals. This board will integrate a new analog acquisition chip called SAS (Smart Auto-triggering Sampler) introducing thus a new analog front-end but inheriting most of the digital logic present in the current DAQ board discussed in this thesis. For what concern the activity on high-resolution vertex detectors, I worked within the SLIM5 collaboration for the characterization of a MAPS (Monolithic Active Pixel Sensor) device called APSEL-4D. The mentioned chip is a matrix of 4096 active pixel sensors with deep N-well implantations meant for charge collection and to shield the analog electronics from digital noise. The chip integrates the full-custom sensors matrix and the sparsifification/readout logic realized with standard-cells in STM CMOS technology 130 nm. For the chip characterization a test-beam has been set up on the 12 GeV PS (Proton Synchrotron) line facility at CERN of Geneva (CH). The collaboration prepared a silicon strip telescope and a DAQ system (hardware and software) for data acquisition and control of the telescope that allowed to store about 90 million events in 7 equivalent days of live-time of the beam. My activities concerned basically the realization of a firmware interface towards and from the MAPS chip in order to integrate it on the general DAQ system. Thereafter I worked on the DAQ software to implement on it a proper Slow Control interface of the APSEL4D. Several APSEL4D chips with different thinning have been tested during the test beam. Those with 100 and 300 um presented an overall efficiency of about 90% imparting a threshold of 450 electrons. The test-beam allowed to estimate also the resolution of the pixel sensor providing good results consistent with the pitch/sqrt(12) formula. The MAPS intrinsic resolution has been extracted from the width of the residual plot taking into account the multiple scattering effect.

Aufbau des GDH-Experiments und Messung der Helizitätsabhängigkeit von gamma p p pi + pi- von der Schwelle bis 800 MeV

Das Experiment zur Überprüfung der Gerasimov-Drell-Hearn(GDH)-Summenregel am Mainzer Mikrotron diente zur Messunghelizitätsabhängiger Eigenschaften der Photoproduktion amProton. Hierbei konnten neben den totalen Photoabsorptionswirkungsquerschnitten auch Querschnitte partieller Kanäle der Einpion-, Zweipion- und Eta-Produktion bestimmt werden. Für die möglichen Doppel-Pion-Reaktionen sind zur Zeit nur wenig Information vorhanden. Daher sind die Reaktionsmechanismen der Doppel-Pion-Photoproduktion weitgehend noch unverstanden. Aus diesem Grund ist die Untersuchung weiterer Observablenerforderlich. Die Helizitätsabhängigkeit stellt eine solcheneue Observable dar und kann dadurch gemessen werden, daßein zirkular polarisiertes Photon mit einem longitudinalpolarisierten Nukleon wechselwirkt. Der Photonspin beträgt1 und der Fermionenspin des Nukleons beträgt 1/2.Die Spins koppeln zu 3/2 und 1/2. Dies liefert diehelizitätsabhängigen Wirkungsquerschnitte.Diese Dissertation beschreibt den Aufbau des Mainzer GDH-Experiments und die technische Realisation der Messung helizitätsabhängiger Photoabsorptionswirkungsquerschnitte. Die Helizitätsabhängigkeit der doppelt geladenen Doppel-Pion-Photoproduktion am Proton wurde anhand der gemessenen Daten untersucht. Diese Reaktion ist ein Zweistufenprozeß, wobei das angeregte Nukleon resonant oder nicht-resonant in die Endzustandsteilchen zerfällt. Durch die helizitätsabhängigen Daten wurden Freiheitsgradein der Doppel-Pion-Photoproduktion eingeschränkt, wodurch eine Verbesserung der Modelle der Gent-Mainz- und der Valencia-Gruppe ermöglicht wurde. Die im Rahmen dieser Arbeit ermittelten Daten haben zusätzlich eine Motivation für weitere Interpretationsansätze durch die genanntenTheoriegruppen geschaffen.