Micropillar compression studies on a bulk metallic glass in different structural states

Uniaxial compression experiments on 0.3, 1 and 3 mu m diameter micropillars of a Zr-based bulk metallic glass in as-cast, shot-peened and structurally relaxed conditions were conducted. Shear band formation and stable propagation is observed to be the plastic deformation mode in all cases, with no detectable difference in yield strength according to either size or condition. The limitations of uniaxial compression tests in assessing the influence of various material conditions on plasticity, when it is inhomogeneous in nature, are illustrated.

Liquefaction And Pore Water Pressure Generation In Sand - A Cyclic Strain Approach

This paper presents the results of laboratory investigation carried out on Ahmedabad sand on the liquefaction and pore water pressure generation during strain controled cyclic loading. Laboratory experiments were carried out on representative natural sand samples (base sand) collected from earthquake-affected area of Ahmedabad City of Gujarat State in India. A series of strain controled cyclic triaxial tests were carried out on isotropically compressed samples to study the influence of different parameters such as shear strain amplitude, initial effective confining pressure, relative density and percentage of non-plastic fines on the behavior of liquefaction and pore water pressure generation. It has been observed from the laboratory investigation that the potential for liquefaction of the sandy soils depends on the shear strain amplitude, initial relative density, initial effective confining pressure and non-plastic fines. In addition, an empirical relationship between pore pressure ratio and cycle ratio independent of the number of cycles of loading, relative density, confining pressure, amplitude of shear strain and non-plastic fines has been proposed.

Flow and heat transfer in a stagnation-point flow over a stretching sheet with a magnetic field

The flow and heat transfer problem in the boundary layer induced by a continuous moving surface is important in many manufacturing processes in industry such as the boundary layer along material handling conveyers, the aerodynamic extrusion of plastic sheet, the cooling of an infinite metalic plate in a cooling bath (which may also be electrolyte). Glass blowing, continuous casting and spinning of fibres also involve the flow due to a stretching surface. Sakiadis [1] was the first to study the flow induced by a semi-infinite moving wall in an ambient fluid. On the other hand, Crane [2] first studied the flow over a linearly stretching sheet in an ambient fluid. Subsequently, Crane [3] also investigated the corresponding heat transfer problem. Since then several authors [4-8] have studied various aspects of this problem such as the effects of mass transfer, variable wall temperature, constant heat flux, magnetic field etc. Recently, Andersson [9] has obtained an exact solution of the Navier-Stokes equations for the MHD flow over a linearly stretching sheet in an ambient fluid. Also Chiam [10] has studied the heat transfer with variable thermal conductivity on a stretching sheet when the velocities of the sheet and the free stream are equal.

Dynamic strain ageing in Ni-base superalloy 720Li

An experimental investigation into the dynamic strain ageing (DSA) of a wrought Ni-base superalloy 720Li was conducted. Characteristics of jerky, flow have been studied at intermediate temperatures of 350, 400 and 450 degrees C at strain-rates between 10(-3) and 10(-5) s(-1). Serrations of Type C are predominant within the temperature/strain-rate range explored. The major characteristics of the serrations-i.e. (a) critical plastic strain for onset of serrations, epsilon(c); (b) average stress decrement, Delta sigma(avg); and (c) strain increment between serrations. Delta epsilon(BS)-have been examined at selected temperatures and strain-rates. Negative strain-rate sensitivity was observed in the DSA regime. However. temperature did not influence tensile properties such as yield strength, ultimate strength. elongation, reduction in area, and work hardening rate or fracture features in DSA regime. Analysis of the results Suggests that locking of the mobile dislocations by substitutional alloying elements is responsible for the DSA in alloy 720Li.

Influence of Martensite Content and Morphology on Tensile and Impact Properties of High-Martensite Dual-Phase Steels

A series of dual-phase (DP) steels containing finely dispersed martensite with different volume fractions of martensite (V-m) were produced by intermediate quenching of a boron- and vanadium-containing microalloyed steel. The volume fraction of martensite was varied from 0.3 to 0.8 by changing the intercritical annealing temperature. The tensile and impact properties of these steels were studied and compared to those of step-quenched steels, which showed banded microstructures. The experimental results show that DP steels with finely dispersed microstructures have excellent mechanical properties, including high impact toughness values, with an optimum in properties obtained at similar to 0.55 V-m. A further increase in V-m was found to decrease the yield and tensile strengths as well as the impact properties. It was shown that models developed on the basis of a rule of mixtures are inadequate in capturing the tensile properties of DP steels with V-m > 0.55. Jaoul-Crussard analyses of the work-hardening behavior of the high-martensite volume fraction DP steels show three distinct stages of plastic deformation.

Some Considerations on the Occurrence of Intergranular Fracture during Fatigue Crack growth in Steels

The occurrence of a maximum in the percentage of intergranular fracture on the fracture surface during the transition from intermediate to low fatigue crack growth rates has been observed for a high strength steel. It is suggested that transgranular planar slip leading to slip localization is essential in promoting intergranular fracture when the cyclic plastic zone size becomes equal to the prior austenite grain size.

1-Methylcyclopropene Delays Softening in Tomato Slices

I-Methylcyclopropene (1-MCP) has the potential in tomato to reduce ethylene-associated changes in texture. Tomato cv. 'Revolution' was harvested at the 'pink' maturity stage and whole fruit treated with 0, 0.1, 1.0 or 10.0 µL.L-' 1-MCP at 20 "C for 12 h. Slices of 7-mm thickness were cut using a commercial slicer, and the slices stored in vertical stacks in plastic containers at 5°C for 7 days. The application of 1-MCP reduced both ethylene production and respiration rate of slices and resulted in firmer pericarp firmness. Ethylene production was 24%, 40%, and 62% lower following 0.1, 1.0, 10.0 µL L-' 1-MCP, respectively, compared with controls. In addition, respiration rate was reduced 6%, 10% and 20% by those 1-MCP treatments. 1-MCP treatments produced 20%, 34%, and 24% higher pericarp firmness, respectively, than in fruit not treated with 1-MCP.

Exposure of Tomato Fruit to 1-MCP Improves Quality of Stored Slices

Maintenance of quality, such as firmness, is important during storage of fresh cut produce. This study compared the effects of I-MCP on the quality of tomato slices when intact tomatoes were treated with 1-MCP and then sliced, or tomatoes were sliced and the slices treated with I-MCP. In both instances the MCP treatment was 1 µL Lˉٰ at 20 ºC for 12 h. Tomato cv. 'Revolution' was harvested at the 'pink' stage of maturity, cut into 7-mm slices, and stored as vertical stacks in closed plastic containers at 5ºC for up to 7 days after the 1-MCP treatment. Exposure of intact tomatoes to I-MCP resulted in reduced ethylene production (31%) and firmer (22%) slices than when tomatoes were not I-MCP treated. The application of I-MCP prior to slicing of tomatoes appears a useful strategy to retain quality of stored tomato slices.

Evaluation of Inoculated Lablab Silage for Growing Dairy Heifers

A summer grown forage legume crop – Lablab (Lablab purpureus) harvested in autumn, was ensiled as plastic wrapped, large round bales. Of the 30 bales produced, 13 were inoculated with a bacterial inoculant containing Lactobacillus plantarum and Enterococcus faecium. Inoculant was premixed at 30 g/litre water, cultured overnight (18 hours) then sprayed onto cut forage during the baling and wrapping procedure at 1 litre per tonne of silage. A replicated feeding experiment was conducted in July - August 1998 (5 weeks), using 24 eight month old Holstein Friesian heifers group fed non-inoculated or inoculated silage to appetite plus 2 kg rolled sorghum grain/heifer.day. Chemical composition and nutritive value of well preserved bales of control and inoculated silages were similar (P>0.05) with 50% DM and 26 g N and 6.8 MJ ME per kg DM. Lactic acid and acetic acid concentrations were 11.4 v. 11.4 and 4.90 v. 3.75 g/kg DM for control and inoculated silages respectively (P>0.05). Heifers preferentially selected leaf from the silage offered and maintained liveweight gains of 0.70 and 0.61 kg/day respectively (P>0.05) during the silage feeding period. High DM and low WSC content of the parent forage may have reduced the opportunity for the bacterial inoculant to have effect. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Use of electronic portal imaging devices for electron treatment verification

This study aims to help broaden the use of electronic portal imaging devices (EPIDs) for pre-treatment patient positioning verification, from photon-beam radiotherapy to photon- and electron-beam radiotherapy, by proposing and testing a method for acquiring clinicallyuseful EPID images of patient anatomy using electron beams, with a view to enabling and encouraging further research in this area. EPID images used in this study were acquired using all available beams from a linac configured to deliver electron beams with nominal energies of 6, 9, 12, 16 and 20 MeV, as well as photon beams with nominal energies of 6 and 10 MV. A widely-available heterogeneous, approximately-humanoid, thorax phantom was used, to provide an indication of the contrast and noise produced when imaging different types of tissue with comparatively realistic thicknesses. The acquired images were automatically calibrated, corrected for the effects of variations in the sensitivity of individual photodiodes, using a flood field image. For electron beam imaging, flood field EPID calibration images were acquired with and without the placement of blocks of water-equivalent plastic (with thicknesses approximately equal to the practical range of electrons in the plastic) placed upstream of the EPID, to filter out the primary electron beam, leaving only the bremsstrahlung photon signal. While the electron beam images acquired using a standard (unfiltered) flood field calibration were observed to be noisy and difficult to interpret, the electron beam images acquired using the filtered flood field calibration showed tissues and bony anatomy with levels of contrast and noise that were similar to the contrast and noise levels seen in the clinically acceptable photon beam EPID images. The best electron beam imaging results (highest contrast, signal-to-noise and contrast-to-noise ratios) were achieved when the images were acquired using the higher energy electron beams (16 and 20 MeV) when the EPID was calibrated using an intermediate (12 MeV) electron beam energy. These results demonstrate the feasibility of acquiring clinically-useful EPID images of patient anatomy using electron beams and suggest important avenues for future investigation, thus enabling and encouraging further research in this area. There is manifest potential for the EPID imaging method proposed in this work to lead to the clinical use of electron beam imaging for geometric verification of electron treatments in the future.

Kirurgisen operaation teatteri : Teatterillinen kuva ja ihmismuodon esitettävyys avantgardistisen väkivallan näkökulmasta

Dissertation considers the birth of modernist and avant-gardist authorship as a reaction against mass society and massculture. Radical avant-gardism is studied as figurative violence done against the human form. The main argument claims avant-gardist authorship to be an act of masculine autogenesis. This act demands human form to be worked to an elementary state of disarticulateness, then to be reformed to the model of the artist's own psychophysical and idiosyncratic vision and experience. This work is connected to concrete mass, mass of pigment, charcoal, film, or flesh. This mass of the figure is worked to create a likeness in the nervous system of the spectator. The act of violence against the human figure is intended to shock the spectator. This shock is also a state of emotional and perceptional massification. I use theatrical image as heuristic tool and performance analysis, connecting figure and spectator into a larger image, which is constituted by relationships of mimesis, where figure presents the likeness of the spectator and spectator the likeness of the figure. Likeness is considered as both gestural - social mimetic - and sensuous - kinesthetically mimetic. Through this kind of construction one can describe and contextualize the process of violent autogenesis using particular images as case studies. Avant-gardist author is the author of theatrical image, not particular figure, and through act of massification the nervous system of the spectator is also part of this image. This is the most radical form and ideology of avant-gardist and modernist authorship or imagerial will to power. I construct a model of gestural-mimic performer to explicate the nature of violence done for human form in specific works, in Mann's novella Death in Venice, in Schiele's and Artaud's selfportaits, in Francis Bacon's paintings, in Beckett's shortplat NOT I, in Orlan's chirurgical performance Operation Omnipresense, in Cindy Sherman's Film/Stills, in Diamanda Galás's recording Vena Cava and in Hitchcock's Psycho. Masspsychology constructed a phobic picture of human form's plasticity and capability to be constituted by influencies coming both inside and outside - childhood, atavistic organic memories, urban field of nervous impulses, unconsciousness, capitalist (image)market and democratic masspolitics. Violence is then antimimetic and antitheatrical, a paradoxical situation, considering that massmedias and massaudiences created an enormous fascination about possibilities of theatrical and hypnotic influence in artistic elites. The problem was how to use theatrical image without coming as author under influence. In this work one possible answer is provided: by destructing the gestural-mimetic performer, by eliminating representations of mimic body techniques from the performer of human (a painted figure, a photographed figure, a filmed figure or an acted figure, audiovisual or vocal) figure. This work I call the chirurgical operation, which also indicates co-option with medical portraitures or medico-cultural diagnoses of human form. Destruction of the autonomy of the performer was a parallel process to constructing the new mass media audience as passive, plastic, feminine. The process created an image of a new kind of autotelic masculine author-hero, freed from human form in its bourgeois, aristocratic, classical and popular versions.

Calorimetric, infrared and ESR studies of the plastically crystalline state of organic compounds

Enthalpy changes of the crystal-plastic and plastic-liquid transitions are related to the temperature range of stability of the plastic phase. Thermodynamics of the plastic state of binary mixtures have been examined. Infrared correlation times, τc, and activation energies have been measured for a few molecules in the plastic state. Molecular tumbling times, τt, have also been measured employing ESR spectra of a spin-probe. Plots of log τc(τt) 1/T are continuous through the plastic-liquid transition. Activation energies for molecular motion seem to vary in the same direction as the ΔH of the plastic-crystal transition. Infrared correlation times of solute molecules in binary solutions in the plastic and the liquid states show interesting variations with solute concentration.

Wideband acoustic absorption characteristics of rubberized coir for underwater applications

Reflection and transmission coefficients of rubberized coir pads over the frequency band 200 kHz to 4 MHz are presented in this Paper. These results are compared with those reported for neoprene, paraffin wax, rubber car mat and plastic door mat1. The rubberized coir pads were found to possess wideband absorption characteristics. It has been experimentally found that 0.05 m thick coir pads have almost 100% absorption in the frequency range 800 kHz-3 MHz with a maximum at 2.35 MHz. We have used this material for lining the water tank for underwater acoustic studies.

Comparative growth and pathogenicity of geographical isolates of Sclerotinia sclerotiorum on lentil genotypes

Isolates of Sclerotinia sclerotiorum were collected from infected lentil plants from 2 agro-ecological zones of Syria and used to study their comparative growth on culture media and pathogenicity on different lentil genotypes. The growth studies were carried out on Potato Dextrose Agar (PDA) growth media under laboratory conditions. Mycelial radial growth and sclerotial production were the parameters used to compare the isolates. Pathogenicity studies were carried out with selected isolates on 10 lentil genotypes, infected as detached shoots and as whole potted-plants in the plastic house. The isolates showed considerable variation in cultural characteristics through mycelial growth, mycelial pigmentation and sclerotial production in the media plates. There were significant differences in the growth and sclerotial production of most of the isolates, but no apparent correlation between mycelial growth and sclerotial production among the isolates. Genotype by isolate interactions was significant for the isolates tested for pathogenicity. These interactions, however, appeared to be caused by differences in virulence of the isolates and did not suggest the occurrence of distinct pathogenic races of the pathogen isolates.

Effects of particle size distribution in the response of model granular materials in multi-ring shear

Rail track undergoes complex loading patterns under moving traffic conditions compared to roads due to its continued and discontinued multi-layered structure, including rail, sleepers, ballast layer, sub-ballast layer, and subgrade. Particle size distributions (PSDs) of ballast, subballast, and subgrade layers can be critical in cyclic plastic deformation of rail track under moving traffic on frequent track degradation of rail tracks, especially at bridge transition zones. Conventional test approaches: static shear and cyclic single-point load tests are however unable to replicate actual loading patterns of moving train. Multi-ring shear apparatus; a new type of torsional simple shear apparatus, which can reproduce moving traffic conditions, was used in this study to investigate influence of particle size distribution of rail track layers on cyclic plastic deformation. Three particle size distributions, using glass beads were examined under different loading patterns: cyclic sin-gle-point load, and cyclic moving wheel load to evaluate cyclic plastic deformation of rail track under different loading methods. The results of these tests suggest that particle size distributions of rail track structural layers have significant impacts on cyclic plastic deformation under moving train load. Further, the limitations in con-ventional test methods used in laboratories to estimate the plastic deformation of rail track materials lead to underestimate the plastic deformation of rail tracks.