Test methods for concrete durability indicators

Durability of concrete structures is primarily dependent on the environmental influences, i.e. the penetration of aggressive substances in the structural element from the environment. Penetrability is an important durability indicator of concrete and by specifying different classes of penetrability of concrete it should be possible to design a structure with the required resistance to environmental loads. This chapter covers descriptions of the available and commonly applied in situ and laboratory, non-invasive and semi-invasive test methods for evaluating concrete penetrability properties.

Adaptive backstepping droop controller design for multi-terminal high-voltage direct current systems

Wind power is one of the most developed renewable energy resources worldwide. To integrate offshore wind farms to onshore grids, the high-voltage direct current (HVDC) transmission cables interfaced with voltage source converters (VSCs) are considered to be a better solution than conventional approaches. Proper DC voltage indicates successive power transfer. To connect more than one onshore grid, the DC voltage droop control is one of the most popular methods to share the control burden between different terminals. However, the challenges are that small droop gains will cause voltage deviations, while higher droop gain settings will cause large oscillations. This study aims to enhance the performance of the traditional droop controller by considering the DC cable dynamics. Based on the backstepping control concept, DC cables are modelled with a series of capacitors and inductors. The final droop control law is deduced step-by-step from the original remote side. At each step the control error from the previous step is considered. Simulation results show that both the voltage deviations and oscillations can be effectively reduced using the proposed method. Further, power sharing between different terminals can be effectively simplified such that it correlates linearly with the droop gains, thus enabling simple yet accurate system operation and control.

Testing preference formation in learning design contingent valuation (LDCV) using advanced information and repetitive treatments

Policymakers have largely replaced Single Bounded Discrete Choice (SBDC) valuation by the more statistically efficient repetitive methods; Double Bounded Discrete Choice (DBDC) and Discrete Choice Experiments (DCE) . Repetitive valuation permits classification into rational preferences: (i) a priori well-formed; (ii) consistent non-arbitrary values “discovered” through repetition and experience; (Plott, 1996; List 2003) and irrational preferences; (iii) consistent but arbitrary values as “shaped” by preceding bid level (Tufano, 2010; Ariely et al., 2003) and (iv) inconsistent and arbitrary values. Policy valuations should demonstrate behaviorally rational preferences. We outline novel methods for testing this in DBDC applied to renewable energy premiums in Chile.

'Talk to me': a mixed methods study on preferred physician behaviours during end-of-life communication from the patient perspective

Background
Despite the recognized importance of end-of-life (EOL) communication between patients and physicians, the extent and quality of such communication is lacking.

Objective
We sought to understand patient perspectives on physician behaviours during EOL communication.

Design
In this mixed methods study, we conducted quantitative and qualitative strands and then merged data sets during a mixed methods analysis phase. In the quantitative strand, we used the quality of communication tool (QOC) to measure physician behaviours that predict global rating of satisfaction in EOL communication skills, while in the qualitative strand we conducted semi-structured interviews. During the mixed methods analysis, we compared and contrasted qualitative and quantitative data.

Setting and Participants
Seriously ill inpatients at three tertiary care hospitals in Canada.

Results
We found convergence between qualitative and quantitative strands: patients desire candid information from their physician and a sense of familiarity. The quantitative results (n = 132) suggest a paucity of certain EOL communication behaviours in this seriously ill population with a limited prognosis. The qualitative findings (n = 16) suggest that at times, physicians did not engage in EOL communication despite patient readiness, while sometimes this may represent an appropriate deferral after assessment of a patient's lack of readiness.

Conclusions
Avoidance of certain EOL topics may not always be a failure if it is a result of an assessment of lack of patient readiness. This has implications for future tool development: a measure could be built in to assess whether physician behaviours align with patient readiness.

New methods for studying perception and action coupling

To study perception and action, Gibson advocated that “the laboratory must be like life” (Gibson, 1979, p. 3). In other words, the interactive relationship between an organism and his/her envi- ronment must be maintained so that the behavior observed in an experimental context mirrors, as closely as possible, the behavior observed in a realistic sport setting. The concept of repre- sentative design introduced by Brunswik in 1956 emphasized the need to have experimental tasks that allow the player to pick up perceptual information that specifies a property of the environment-actor system (Araújo et al., 2005; see also Chapter 24). In this chapter we will provide a brief overview of the methodologies used to study perception and action in sport and present, in some detail, the opportunities new methodologies such as immersive, interactive vir- tual reality can offer researchers in sport expertise.

Investigation of Utilizing Single Surface Depressions in Optimization of NLF Aerofoil Design

An environment has been created for the optimisation of aerofoil profiles with inclusion of small surface features. For TS wave dominated flows, the paper examines the consequences of the addition of a depression on the aerodynamic optimisation of an NLF aerofoil, and describes the geometry definition fidelity and optimisation algorithm employed in the development process. The variables that define the depression for this optimisation investigation have been fixed, however a preliminary study is presented demonstrating the sensitivity of the flow to the depression characteristics. Solutions to the optimisation problem are then presented using both gradient-based and genetic algorithm techniques, and for accurate representation of the inclusion of small surface perturbations it is concluded that a global optimisation method is required for this type of aerofoil optimisation task due to the nature of the response surface generated. When dealing with surface features, changes in the transition onset are likely to be of a non-linear nature so it is highly critical to have an optimisation algorithm that is robust, suggesting that for this framework, gradient-based methods alone are not suited.

How individual participant data meta-analyses have influenced trial design, conduct, and analysis

OBJECTIVES: To demonstrate how individual participant data (IPD) meta-analyses have impacted directly on the design and conduct of trials and highlight other advantages IPD might offer.

STUDY DESIGN AND SETTING: Potential examples of the impact of IPD meta-analyses on trials were identified at an international workshop, attended by individuals with experience in the conduct of IPD meta-analyses and knowledge of trials in their respective clinical areas. Experts in the field who did not attend were asked to provide any further examples. We then examined relevant trial protocols, publications, and Web sites to verify the impacts of the IPD meta-analyses. A subgroup of workshop attendees sought further examples and identified other aspects of trial design and conduct that may inform IPD meta-analyses.

RESULTS: We identified 52 examples of IPD meta-analyses thought to have had a direct impact on the design or conduct of trials. After screening relevant trial protocols and publications, we identified 28 instances where IPD meta-analyses had clearly impacted on trials. They have influenced the selection of comparators and participants, sample size calculations, analysis and interpretation of subsequent trials, and the conduct and analysis of ongoing trials, sometimes in ways that would not possible with systematic reviews of aggregate data. We identified additional potential ways that IPD meta-analyses could be used to influence trials.

CONCLUSIONS: IPD meta-analysis could be better used to inform the design, conduct, analysis, and interpretation of trials.

Wing Panel Design with Novel Skin-Buckling Containment Features

The impact of buckling containment features on the stability of thin-gauge fuselage, metallic stiffened panels has previously been demonstrated. With the continuing developments in manufacturing technology, such as welding, extrusion, machining, and additive layer manufacture, understanding the benefits of additional panel design features on heavier applications, such as wing panels, is timely. This compression testing of thick-gauge panels with and without buckling containment features has been undertaken to verify buckling and collapse behaviors and validate sizing methods. The experimental results demonstrated individual panel mass savings on the order of 9%, and wing cover design studies demonstrated mass savings on the order of 4 to 13%, dependent on aircraft size and material choice.

A simplified procedure for sizing solar thermal systems based on national assessment methods in the UK and Ireland.

Solar heating systems have the potential to be an efficient renewable energy technology, provided they are sized correctly. Sizing a solar thermal system for domestic applications does not warrant the cost of a simulation. As a result simplified sizing procedures are required. The size of a system depends on a number of variables including the efficiency of the collector itself, the hot water demand and the solar radiation at a given location. Domestic Hot Water (DHW) demand varies with time and is assessed using a multi-parameter detailed model. Secondly, the national energy evaluation methodologies are evaluated from the perspective of solar thermal system sizing. Based on the assessment of the standards, limitations in the evaluation method for solar thermal systems are outlined and an adapted method, specific to the sizing of solar thermal systems, is proposed. The methodology is presented for two common dwelling scenarios. Results from this showed that it is difficult to achieve a high solar fraction given practical sizes of system infrastructure (storage tanks) for standard domestic properties. However, solar thermal systems can significantly offset energy loads due associated DHW consumption, particularly when sized appropriately. The presented methodology is valuable for simple solar system design and also for the quick comparison of salient criteria.

Estimation of the small strain stiffness of glacial till using geophysical methods and barometric loading response

Stiffness values in geotechnical structures can range over many orders of magnitude for relatively small operational strains. The typical strain levels where soil stiffness changes most dramatically is in the range 0.01-0.1%, however soils do not exhibit linear stress-strain behaviour at small strains. Knowledge of the in situ stiffness at small strain is important in geotechnical numerical modelling and design. The stress-strain regime of cut slopes is complex, as we have different principle stress directions at different positions along the potential failure plane. For example, loading may be primarily in extension near the toe of the slope, while compressive loading is predominant at the crest of a slope. Cuttings in heavily overconsolidated clays are known to be susceptible to progressive failure and subsequent strain softening, in which progressive yielding propagates from the toe towards the crest of the slope over time. In order to gain a better understanding of the rate of softening it would be advantageous to measure changes in small strain stiffness in the field.

Defining consensus norms for palliative care of people with intellectual disabilities in Europe using Delphi methods: A White Paper from the European Association of Palliative care

Background: People with intellectual disabilities often present with unique challenges that make it more difficult to meet their
palliative care needs.
Aim: To define consensus norms for palliative care of people with intellectual disabilities in Europe.
Design: Delphi study in four rounds: (1) a taskforce of 12 experts from seven European countries drafted the norms, based on available empirical knowledge and regional/national guidelines; (2) using an online survey, 34 experts from 18 European countries evaluated the draft norms, provided feedback and distributed the survey within their professional networks. Criteria for consensus
were clearly defined; (3) modifications and recommendations were made by the taskforce; and (4) the European Association for
Palliative Care reviewed and approved the final version.
Setting and participants: Taskforce members: identified through international networking strategies. Expert panel: a purposive sample identified through taskforce members’ networks.
Results: A total of 80 experts from 15 European countries evaluated 52 items within the following 13 norms: equity of access, communication, recognising the need for palliative care, assessment of total needs, symptom management, end-of-life decision making, involving those who matter, collaboration, support for family/carers, preparing for death, bereavement support, education/training
and developing/managing services. None of the items scored less than 86% agreement, making a further round unnecessary. In light of respondents’ comments, several items were modified and one item was deleted.
Conclusion: This White Paper presents the first guidance for clinical practice, policy and research related to palliative care for people with intellectual disabilities based on evidence and European consensus, setting a benchmark for changes in policy and practice.

Spectacle design preferences among Chinese primary and secondary students and their parents: A qualitative and quantitative study

Purpose: To identify the specific characteristics making glasses designs, particularly those compatible with adjustable glasses, more or less appealing to Chinese children and their parents. Patients and Methods: Primary and secondary school children from urban and rural China with < = -1.00 diopters of bilateral myopia and their parents ranked four conventional-style frames identified by local optical shops as popular versus four child-specific frames compatible with adjustable spectacles. Scores based on the proportion of maximum possible ranking were computed for each style. Selected children and their parents also participated in Focus Groups (FGs) discussing spectacle design preference. Recordings were transcribed and coded by two independents reviewers using NVivo software. Results: Among 136 urban primary school children (age range 9-11 years), 290 rural secondary school children (11-17 years) and 16 parents, all adjustable-style frames (scores on 0-100 scale 25.7-62.4) were ranked behind all conventional frames (63.0-87.5). For eight FGs including 12 primary children, 26 secondary children and 16 parents, average kappa values for NVivo coding were 0.81 (students) and 0.70 (parents). All groups agreed that the key changes to make adjustable designs more attractive were altering the round lenses to rectangular or oval shapes and adding curved earpieces for more stable wear. The thick frames of the adjustable designs were considered stylish, and children indicated they would wear them if the lens shape were modified. Conclusions: Current adjustable lens designs are unattractive to Chinese children and their parents, though this study identified specific modifications which would make them more appealing.

Design, synthesis and validation of an inhibitor of CGRP degradation

Introduction: In addition to their afferent role in detection and signalling noxious stimuli, neuropeptide-containing sensory nerves may initiate and maintain chronic inflammation in diseases such as periodontitis by an efferent process known as neurogenic inflammation. Neuropeptides are susceptible to cleavage by peptidases, and therefore, the exact location and level of expression of peptidases are major determinants of neuropeptide action. Previous studies in our laboratory showed that enzyme components of gingival crevicular fluid (GCF) from periodontitis sites selectively inactivated the neuropeptide calcitonin gene-related peptide (CGRP), known to have a role in inhibiting osteoclastic bone resorption. Objectives: The aim of this study was to design and synthesise a specific inhibitor to prevent the degradation of CGRP by components of GCF. Methods: A hydroxamate-based inhibitor with a biotinylated tag was designed to ensure selectivity for CGRP and ease of use for future purification strategies. The biotinylated peptide hydroxamate contained the P1-P4 amino acid sequence of the potential CGRP cleavage site and was synthesised by solid-phase methods using standard Fmoc chemistry. Inhibition of CGRP metabolism by GCF was determined by MALDI-mass spectrometry (MALDI-MS) using pooled GCF samples from periodontitis patients as a crude source of the CGRP-degrading enzyme. Results: MALDI-MS analysis of CGRP degradation showed almost complete inhibition in the presence of the biotinylated inhibitor. Our results showed that the rate-limiting step in the cleavage of CGRP is endopeptidase cleavage, followed by carboxypeptidase attack. Conclusion: This study demonstrates that the enzyme component of GCF responsible for the degradation of CGRP can be inhibited by a biotinylated hydroxamate modelled on a potential endopeptidase cleavage site. The biotin tag on the inhibitor will facilitate our future purification of the CGRP-cleavage enzyme using a streptavidin-agarose column.

Novel methods of drug administration for the treatment and care of older patients

The number of older people globally is increasing, contributing to a growing burden of morbidity and mortality. With this shift in population demographic, comes a new challenge in terms of appropriate healthcare for the over 65 years age group. As medication is the principal therapeutic intervention, it is essential that it be fully optimised, to meet the needs of this heterogeneous population. The most common routes of drug administration are oral and injectable, which may display some limitations for older people, in cases of dysphagia or frailty for example. This review considers alternative methods of drug delivery to the norm, specifically discussing the nasal, pulmonary and transdermal routes, as well as novel orally disintegrating tablets. The changing physiology as ageing occurs must be considered in the development of novel drug delivery devices. This review considers the various aspects of ageing that will influence future drug formulation design and development.

A Design & Feasibility Study of the Spaced Learning Programme

Objectives There is evidence from neuroscience, cognitive psychology and educational research that the delivery of a stimulus in a spaced format (over time) rather than a massed format (all at once) leads to more effective learning. This project aimed to pilot spaced learning materials using various spacing lengths for GCSE science by exploring the feasibility of introducing spaced leaning into regular classrooms and by evaluating teacher fidelity to the materials. The spaced learning methods will then be compared with traditional science revision techniques and a programme manual will be produced. Design A feasibility study. Methods A pilot study (4 schools) was carried out to examine the feasibility and teacher fidelity to the materials, using pupil workshops and teacher interviews. A subsequent random assignment experimental study (12 schools) will involve pre and post testing of students on a science attainment measure and a post-test implementation questionnaire. Results The literature review found that longer spacing intervals between repetitions of material (>24 hours) may be optimal for long term memory formation than shorter intervals. A logic model was developed to inform the design of various programme variants for the pilot and experimental study. This paper will report qualitative data from the initial pilot study. Conclusions The paper uses this research project as an example to explain the importance of conducting pilot work and small scale experimental studies to explore the feasibility and inform the design of educational interventions, rather than prematurely moving to RCT type studies.