3D quench simulation using finite element method for CR superconducting magnet's strand

The CR superconducting magnet is a dipole of the FAIR project of GSI in Germany. The quench of the strand is simulated using FEM software ANSYS. From the simulation, the quench propagation can be visualized. Programming with APDL, the value of propagation velocity of normal zone is calculated. Also the voltage increasing over time of the strand is computed and pictured. Furthermore, the Minimum Propagation Zone (MPZ) is studied. At last, the relation between the current and the propagation velocity of normal zone, and the influence of initial temperature on quench propagation are studied.

Optimization of magnetic field for CR dipole magnet

High homogeneity of the CR (collector ring) dipole magnet for FAIR (Facility for Antiproton and Ion Research) project at GSI is essential. The two optimized and analysis methods are introduced in detail. In order to obtain an ideal integral magnetic field distribution, the complicated end chamfer has been designed. By chamfering the removable pole, the distribution tolerance of high magnetic field is optimized to +/- 2 x 10(-4). The method of adding a mirror plane is suitable for the high magnetic field and it doesn't fit the low one. The OPERA is used to optimize the dipole magnetic field.

Stress analysis of CR superferric magnet

Finite Element Method is used in this article to analyze the stress of CR superferric magnet. Magnetic force and the stress caused by this force are calculated. The thermal stress and strain of the coil caused by cooling down is also analyzed. The result will be taken as a check for the design of the coil and coilcase, and also as a reference for the optimization of further design and quench protection.

基于激光诱导击穿光谱技术的铝合金成分定量分析；Quantitative analysis of element concentration in Al alloy by using laser-induced breakdown spectroscopy

利用Nd:YAG激光器输出的532nm激光束对位于空气中的标准变形铝合金样品进行烧蚀产生了激光诱导等离子体.对测量的230—440nm波长范围的光谱进行了谱线标定,同时基于自由定标方法对样品成分进行了定量分析,确定了样品中的元素含量.分析结果与标准值具有较好的一致性.

Quantitative analysis analysis of element concentration in Al alloy by using laser-induced breakdown spectroscopy

Laser-induced breakdown plasma is produced by using Q-switched Nd: YAG laser operating at 532 nm, which interacts with the Al alloy sample target in air. The spectral lines in the 230-440 nm wavelength range have been identified, and based on the calibration-free method, the mass concentration of Al alloy are obtained, which is in good agreement with the standard value of the sample.

Rotation alignment in neutron-rich Cr isotopes: A probe of deformed single-particle levels across N=40

Recent experiments have reached the neutron-rich Cr isotope with N = 40 and confirmed enhanced collectivity near this subshell. The current data focus on low-spin spectroscopy only, with little information on the states where high-j particles align their spins with the system rotation. By applying the projected shell model, we show that rotation alignment occurs in neutron-rich even-even Cr nuclei as early as spin 8 (h) over bar h and, owing to shell filling, the aligning particles differ in different isotopes. It is suggested that observation of irregularities in moments of inertia is a direct probe of the deformed single-particle scheme in this exotic mass region.

Study of a magnetic alloy-loaded RF cavity for bunch compression at the CSR

The Heavy Ion Research Facility and Cooling Storage Ring (HIRFL-CSR) accelerator in Lanzhou offers a unique possibility for the generation of high density and short pulse heavy ion beams by non-adiabatic bunch compression longitudinally, which is implemented by a fast jump of the RF-voltage amplitude. For this purpose, an RF cavity with high electric field gradient loaded with Magnetic Alloy cores has been developed. The results show that the resonant frequency range of the single-gap RF cavity is from 1.13 MHz to 1.42 MHz, and a maximum RF voltage of 40 kV with a total length of 100 cm can be obtained, which can be used to compress heavy ion beams of U-238(72+) with 250 MeV/u from the initial bunch length of 200 ns to 50 ns with the coaction of the two single-gap RF cavity mentioned above.

SUPER-FRS/CR超导磁体力学性能分析

中国签订了为德国FAIR国际大科学工程加工SUPER-FRS/CR超导二极磁铁样机的合作备忘录。该超导二极磁铁属于常温铁芯、低温线圈的超导磁铁，该磁铁的磁场强度0.15～1.6T，偏转角度15°，偏转半径8125mm，磁场精度要求±1×10-4，磁铁总重量约50吨。磁铁铁芯采用0.5mm的硅钢片叠压成型，由中科院近代物理研究（IMP）所计算、设计制造，线圈采用4.2K液氦浸泡式超导线圈，由合肥等离子体所设计制造（IPP）。 超导磁体的力学性能分析一直是超导磁体的基础问题。本文利用有限元分析方法，借助有限分析工具ANSYS、ADINA、OPERA等，分析了超导磁体的电磁场，着重模拟计算了SUPER-FRS/CR超导二极磁铁的电磁力作用；模拟了降温过程，计算了杜瓦、线圈热应力的作用；并对SUPER-FRS/CR超导线圈进行地震载荷作用的模拟。对以上不同的受力作用所遵循的不同的机械设计准则，进行不同的分析，最后计算结果证明设计的结构是安全、可靠的。由于超导线圈的结构复杂，导致在线圈拐角的地方应力有些集中，但是并不影响结构的可靠性。 本文还介绍了超导实验线圈的一些工艺设计，例如超导线圈的绕制，低温材料的选择，电流引线的设计工艺，以及VPI工艺。并对实验磁体进行了一系列的低温性能测试，例如短样测试、降温实验等，获得了一些重要的低温实验参数。这些参数将为以后超导磁体的研制提供宝贵的依据

Cr/Al系统的离子束混合

用600kev的kr~+对Cr/Al薄膜系统进行了离子束混合研究。实验样品是在单晶硅上蒸镀约5000 A厚的铝膜，相继再上所需不同厚度的铬膜。Kr~+注入剂量范围在2.0 * 10~(15)～2.5 * 10~(16) kr~+/cm~2之间。用2.0 Mev的α粒子对注入前后的样品进行了背散射分析，发现铝谱的前沿和铬谱的后沿有明显的展宽，且随剂量的增大而加宽，Cr/Al界面原子混合扩展量的平方α~2注入剂量φ成线性关系；当注入剂量大于1.0 * 10~(16) kr~+/cm~2时，铝谱前沿和铬谱的后沿出现有明显的平坦，经理论拟合计算，发现有化合物形成，x射线衍射实验结果证明化合物形式为Al_(13)Cr_2。本文还得到了混合量Q与剂量的线性关系。最后，对混合机制进行了讨论

Synthesis and characterization of carbon black supported Pt-Ru alloy as a model catalyst for fuel cells

A set of bimetallic Pt-Ru catalysts prepared by co-impregnation of carbon black with ruthenium(III) chloride hydrate and hydrogen hexachloroplatinate(IV) hydrate were investigated by temperature-programmed reduction (TPR), chemisorption of hydrogen, transmission electron microscopy (TEM), microcalorimetry of adsorbed CO and a structure-sensitive reaction (n-hexane conversion). The results showed that the volumetric capacities for CO and H-2 adsorption is influenced in the bimetallic Pt-Ru catalysts by the formation of a Pt-Ru alloy. The n-hexane reaction revealed that the reaction mechanism for the pure Pt catalyst mainly occurs via cyclic isomerization and aromatization due to the presence of bigger Pt surface ensembles, whereas the Pt-Ru catalysts exhibited predominantly bond-shift isomerization by the diluting effect of Ru metal addition. The differential heats of CO chemisorption on Pt-Ru catalysts fell between the two monometallic Pt and Ru catalysts extremes. (C) 2004 Elsevier B.V. All rights reserved.

Electrocatalytic properties of Cu-Zr amorphous alloy towards the electrochemical hydrogenation of nitrobenzene

The Cu-Zr amorphous alloy was studied as an electrocatalyst towards the electrochemical hydrogenation of nitrobenzene. The electrocatalyst was activated by chemical etching in HF solution. Resulted changes in the morphology, chemical composition and crystalline structure of the electrocatalyst surface were characterised by scanning electron microscopy, X-ray diffraction and Auger electron spectroscopy. The electrocatalytic properties of the Cu-Zr amorphous alloy were assessed by voltammetric measurements. Due to the formation and aggregation of Zr residue modified Cu nanocrystals on the surface caused by the selective dissolution of Zr components in the chemical etching, the activated amorphous alloy is an effective electrocatalyst for the electrochemical reduction reaction of nitrobenzene with aniline as the main product. The positive shift of the peak potential and accompanying increase in the value of peak current in voltammograms with increasing Cu content and decreasing Zr content of the alloy surface in the chemical etching are indicative of improved electrocatalytic activity. (C) 2002 Elsevier Science B.V. All rights reserved.