Wideband antireflection film fabricated by glancing angle deposition

Graded-index ZrO2 films has been fabricated on K9 glass by glancing angle deposition. Because the index mismatch at the interface has been reduced, the film results in wideband high-transmission antireflection. From 400nm to 1200nm, the film reflection is lower than 0.8% and the lowest value is 0.2% at 432nm.

Nonpolarizing and polarizing filter design

We describe a nonpolarizing filter design at oblique incidence and a polarizing filter design at normal incidence that use a uniaxially anisotropic layer. The phase thicknesses and the optical admittances of 14 the layers are compensated for by the birefringent properties of a thin film at oblique incidence. This concept can be applied to the design of nonpolarizing bandpass and edge filters at oblique incidence and of polarizing beam splitters at normal incidence. Besides, the dependence of narrow-bandpass filters on normal incidence is discussed. (c) 2005 Optical Society of America.

Design of anisotropic reflector with birefringent thin films

A novel design for dielectric anisotropic mirrors with birefringent thin films for normal incidence is presented. This mirror consists of a stack of quarter-wave biaxial layers. The biaxial anisotropic layers can be fabricated by oblique deposition. The reflectance is different for two linear polarizations of light incidence on the mirrors. As a numerical example, the design is carried out on glass with TiO2 and ZrO2. These thin films could be applied to anisotropic reflective devices for lasers.

Optical, structural and laser-induced damage threshold properties of HfO2 thin films prepared by electron beam evaporation

We prepare HfO2 thin films by electron beam evaporation technology. The samples are annealed in air after deposition. With increasing annealing temperature, it is found that the absorption of the samples decreases firstly and then increases. Also, the laser-induced damage threshold (LIDT) increases firstly and then decreases. When annealing temperature is 473K, the sample has the highest LIDT of 2.17J/cm(2), and the lowest absorption of 18 ppm. By investigating the optical and structural characteristics and their relations to LIDT, it is shown that the principal factor dominating the LIDT is absorption.

Thermodynamic damage mechanism of transparent films caused by a low-power laser

A new model for analyzing the laser-induced damage process is provided. In many damage pits, the melted residue can been found. This is evidence of the phase change of materials. Therefore the phase change of materials is incorporated into the mechanical damage mechanism of films. Three sequential stages are discussed: no phase change, liquid phase change, and gas phase change. To study the damage mechanism and process, two kinds of stress have been considered: thermal stress and deformation stress. The former is caused by the temperature gradient and the latter is caused by high-pressure drive deformation. The theory described can determine the size of the damage pit. (c) 2006 Optical Society of America.

离子束辅助技术获得高激光损伤阈值的增透膜

采用合适的离子束辅助沉积（IBAD）参数在K9基底上镀制了高激光损伤阈值的中心波长1053nm的增透膜，分别从光谱性能、吸收性能、抗激光损伤阈值（LIDT）以及退火后的影响等方面与未进行离子束辅助沉积的薄膜进行对比分析。实验结果发现，采用离子辅助制备的薄膜放置80d后具有更好的光谱稳定性，与未进行离子束辅助镀制的薄膜相比，平均吸收下降了57％，吸收值偏高的奇异点明显减少；损伤阈值提高了60％，用Leica偏振光学显微镜观察50％损伤几率的能量下破斑形貌，发现经过离子束辅助制备的样品破斑形状整齐且缺陷点少；

斜角入射沉积法制备渐变折射率薄膜的折射率分析

斜角入射沉积法是一种制备薄膜的新颖方法，它可以用来制备渐变折射率薄膜．本文首先探讨了膜料的沉积入射角为α，薄膜柱状生长倾斜角为β时的薄膜的填充系数；之后利用drude理论，分析研究了斜角入射沉积法制备渐变折射率薄膜的折射率与薄膜的入射角和生长方向的关系．

重复率激光作用下光学薄膜损伤的累积效应

使用脉宽12ns，频率10Hz的1064nm调Q Nd：YAG激光器，研究了高反射膜在重复率激光作用下的损伤的累积效应。实验发现，高反射膜的损伤阈值随辐照脉冲数增加而降低，表现出明显的累积效应。通过对损伤阈值和损伤概率以及辐照次数的统计性研究．并结合单脉冲辐照的结果，说明了存在于薄膜中微小的缺陷参与了多脉冲激光对薄膜的损伤过程。可用预损伤机制解释实验结果。得到了关于IBS制备的高反射膜的损伤阈值和照射次数的关系式，并用实验结果进行验证．发现具有很好的一致性。实验过程中样品的损伤形貌通过Nomarski偏光

电子束蒸发氧化锆薄膜的粗糙度和光散射特性

利用电子束蒸发工艺，以Ag层为衬底，沉积了中心波长为632．8nm的氧化锆（ZrO2）薄膜，膜层厚度在80-480nm范围内变化．研究了不同厚度样品的粗糙度变化规律和表面散射特性．结果发现，随着膜层厚度的逐渐增加．其表面均方根（RMS）粗糙度和总积分散射（TIS）均呈现出先减小后增大的趋势．利用非相关表面粗糙度的散射模型对样品的TIS特性进行了理论计算，所得结果与测量结果相一致．

Negative dispersion mirrors in Ta2O5/: SiO2 for femtosecond Ti : Sapphire lasers by using gires-tournois interferometers

We design and experimentally demonstrate some negative dispersion mirrors with optimized Gires-Tournois interferometers. The mirror structure is composed of 38 alternating Ta2O5 and SiO2 layers and could be regarded as two sections: high-reflectivity section consisting of a series of quarter-wavelength optical thickness stacks and negative-dispersion section consisting of only 13 layers. The designed mirrors exhibit the expected performance. These mirrors were fabricated by using ion beam sputtering. By adopting such mirrors, dispersion of a mode-locked femtosecond Ti:sapphire laser has been compensated for mostly. With two series of the mirrors, 32 fs and 15 fs pulses have been obtained respectively.

非均匀性对增透膜增透特性的影响

通过对基底与膜层、膜层之间界面处非均匀性对增透膜增透性能影响的讨论，得到以下结论：在沉积初期，由于基底表面特性和沉积参数的波动，从而在基底与膜层之间产生过渡层，使增透性能减弱，对增透膜的增透效果影响较大；在膜层之间的过渡层，正余弦过渡使增透性能变强，双曲、指数使增透性能减弱，但影响较小，线性渐变基本没有影响。实验镀制了增透膜并对其进行拟合分析，发现基底与膜层以及膜层之间的过渡层按正余弦变化时与实验结果比较吻合，并给予了解释。

不同沉积参量下ZrO_2薄膜的微结构和激光损伤阈值

ZrO2采用X射线衍射(XRD)技术分析了不同充氧条件和沉积温度对ZrO2溥膜组成结构的影响，并对不同工艺下制备的薄膜的表面粗糙度和激光损伤阈值进行了测量。结果发现随着氧压的升高，ZrO2溥膜将由单斜相多晶态逐渐转变为非晶态结构，而随着基片温度的增加，溥膜将由非晶态逐渐转变为单斜相多晶态。同时发现随着氧压升高晶粒尺寸减小，而随着沉积温度增加，晶粒尺寸增大。氧压增加时工艺对表面粗糙度有一定程度的改善，而沉积温度升高，工艺对表面粗糙度的改善不明显。晶粒尺寸大小变化与表面粗糙度变化存在对应关系。激光损伤测量表明

脉冲激光辐照光学薄膜的缺陷损伤模型

建立了缺陷吸收升温致薄膜激光损伤模型，该模型从热传导方程出发，考虑了缺陷内部的温度分布以及向薄膜的传导过程，通过引入散射系数简化了Mie散射理论得出的吸收截面．对电子束蒸发沉积的ZrO2：Y2O3单层膜进行了激光破坏实验，薄膜样品的损伤是缺陷引起的，通过辉光放电质谱法对薄膜制备材料的纯度分析发现材料中的主要杂质元素为铂，其含量为0．9％．利用缺陷损伤模型对损伤过程进行了模拟，理论模型和实验结果取得了较好的一致性．

非均匀性对单层膜光学特性的影响

探讨了不同规律的非均匀性对单层膜的光谱特性的影响，与均匀单层膜对比发现：折射率正变引起透射率的极大值减小，折射率负变引起透射率的极大值变大，当非均匀性很小时，透射率的极小值基本不变．对实验制备的单层膜从实验和理论上进行了对比并给出了较好的拟合，发现在薄膜和基底的界面处存在一过渡层，过渡层可近似为线性，并从理论上给予了分析解释．