O sistema aquífero Barreiras na região de Parnamirim, RN: uso das águas e potencialidades

The study area is within the Pirangi River Basin, eastern sector of Rio Grande do Norte state, where is located of the Parnamirim city. It has an area of approximately 370 km². Urbanization has developed much fast without an appropriate infrastructure, mainly by the lack of sewage systems, with risks of contamination of groundwater that may cause serious damage to the health of the population. The Barreiras Aquifer System groundwater in the area represents the main source of water supply for urban and rural populations. The use of groundwater occurs without adequate planning and therefore, important recharge areas are being occupied. This study was conducted to quantify the use and evaluation of the potential of groundwater, in order to increase good water quality supply and lower risks of being affected by polluting activities. With these objectives, the following activities were carried out: 268 points of water have been registered; characterization of the lithological, thickness and hydrogeological structure of the Barreiras aquifer, based on the correlation of well logs; and evaluation of hydrodynamic parameters of the aquifer, from the interpretation of results well pumping tests. It was found that the saturated thickness increases from west to east towards the sea, with values ranging from 15,47-56,5 m with an average of 32,45 m. The hydrodynamic parameters using Cooper-Jacob method were: average transmissivity of 5,9x10-3 m²/s and average hydraulic conductivity 2,82x10-4 m/s. The effective porosity is of 15%, obtained by applying Biecinski equation. The potentiometric map shows the main direction of groundwater flow, from west to east, and identifies the recharge areas corresponding to the region of the tablelands of the "Barreiras". The river valleys refer to the discharge areas of the aquifer system. The Recharge was estimated at 253 mm/year, which corresponds to the 16.4% rate of infiltration.

Evolução estratigráfica da sequência neocarbonífera-eotriássica da Bacia do Parnaíba, NE do Brasil

The Parnaíba Basin consists in an intracratonic basin whose sucession of rocks is arranged in five supersequences. The Upper Carboniferous-Lower Triassic Sequence represents the third major sedimentary cycle and corresponds to Balsas Group, which is divided into four units: Piauí Formation, Pedra de Fogo Formation, Motuca Formation and Sambaíba Formation, from base to top. Different interpretations have been made by several authors in recent decades to interpreted the depositional system and environments related to each unit that belongs to this sequence. In general way, it is described as a thick pack of siliciclastic sediments deposited under complex conditions, varying from clastic/evaporitic shallow marine to lacustrine and desert environment. Aiming to clarify the sedimentary sequence evolution, this work underwent a stratigraphic analysis of the Upper Carboniferous-Lower Triassic deposits by applying modern concepts of the sequence stratigraphy based on well and seismic database. Three main depositional sequences of higher frequency were identified in each well analyzed. The sequence 1 corresponds to rocks initially deposited by a fluvial system with braided channel characteristics which evolved to shallow marine with coastal sabkha conditions related to a transgressive stage, that later evolved to a deltaic system. The Sequence 2 corresponds to rocks deposited in a lacustrine/desert environment associated with sabkha generated during a period of increased aridity in which the area occupied by the Parnaíba Basin had been suffering. The registration of a major regressive phase is shown in Sequence 2 which evolved to a dominantly desert environment recorded in Sequence 3. Seismic stratigraphy analyses allow to define a series of stratigraphic surfaces and related genetic units, as well as to infer its lateral expression. Seismic facies associated with such sequences are dominantly parallel and sub-parallel, with good lateral continuity, suggesting the sedimentary rate was relatively constant during deposition.

Evolução estratigráfica da sequência neocarbonífera-eotriássica da Bacia do Parnaíba, NE do Brasil

The Parnaíba Basin consists in an intracratonic basin whose sucession of rocks is arranged in five supersequences. The Upper Carboniferous-Lower Triassic Sequence represents the third major sedimentary cycle and corresponds to Balsas Group, which is divided into four units: Piauí Formation, Pedra de Fogo Formation, Motuca Formation and Sambaíba Formation, from base to top. Different interpretations have been made by several authors in recent decades to interpreted the depositional system and environments related to each unit that belongs to this sequence. In general way, it is described as a thick pack of siliciclastic sediments deposited under complex conditions, varying from clastic/evaporitic shallow marine to lacustrine and desert environment. Aiming to clarify the sedimentary sequence evolution, this work underwent a stratigraphic analysis of the Upper Carboniferous-Lower Triassic deposits by applying modern concepts of the sequence stratigraphy based on well and seismic database. Three main depositional sequences of higher frequency were identified in each well analyzed. The sequence 1 corresponds to rocks initially deposited by a fluvial system with braided channel characteristics which evolved to shallow marine with coastal sabkha conditions related to a transgressive stage, that later evolved to a deltaic system. The Sequence 2 corresponds to rocks deposited in a lacustrine/desert environment associated with sabkha generated during a period of increased aridity in which the area occupied by the Parnaíba Basin had been suffering. The registration of a major regressive phase is shown in Sequence 2 which evolved to a dominantly desert environment recorded in Sequence 3. Seismic stratigraphy analyses allow to define a series of stratigraphic surfaces and related genetic units, as well as to infer its lateral expression. Seismic facies associated with such sequences are dominantly parallel and sub-parallel, with good lateral continuity, suggesting the sedimentary rate was relatively constant during deposition.

Análise estratigráfica da sequência mesodevoniana-eocarbonífera da Bacia do Parnaíba, nordeste do Brasil

The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.

Análise estratigráfica da sequência mesodevoniana-eocarbonífera da Bacia do Parnaíba, nordeste do Brasil

The Middle Devonian-Early Carboniferous sequence of the Parnaíba Basin, lithostratigraphically defined as Canindé Group, has been reinterpreted using the basic model of sequence stratigraphy. Therefore, lithology and gamma ray well-logs and seismic lines of central portion of the basin were analyzed, producing up from there diagrams 1D, isochore maps and stratigraphic sections. As results of this study, were defined two depositional cycles of second order, referred as Depositional Sequence 1 (SEQ1) and the Depositional Sequence 2 (SEQ2). The SEQ1, with interval about 37 Ma, is limited below by Early Devonian Unconformity and is equivalent to the formations Itaim, Pimenteiras and Cabeças. The SEQ2, which follows, comprises a range of about 15 Ma and is equivalent to the Longá Formation The SEQ1 starts with the lowstand systems tract, consisting of progradational parasequence set in the basal part, predominantly pelitic, deposited on a prodelta under influence of storms and the upper part consists in sandstones of deltaic front, with the maximum regressive surface on the upper limit. The transgressive systems tract, deposited above, is characterized by retrogradacional parasequence set composed of shallow shelf mudstones, deposited under storm conditions. The maximum flooding surface, upper limit of this tract, is positioned in a shale level whose radioactivity in gammaray well-log is close to 150 API. The highstand systems tract presents progradational parasequence set, comprising mudstones and sandstones deposited in shelf, fluvial-estuarine or deltaic and periglacial environments, with the upper limit the Late Devonian Unconformity. The SEQ2 was deposited in shelf environment, starting with the lowstand systems tract, that is characterized by a progradational parasequence set, followed by the transgressive systems tract, with retrogradational character. The upper limit of the tract corresponding to the fusion between maximum flooding surface with the upper limit of this sequence, which is the Early Carboniferous Unconformity, where the overlapping section was eroded. This section, which corresponds the highstand systems tract is restricted to portions at which the erosion that generate the Early-Carboniferous Unconformity was less effective, preserving the records of this unit.

Análise do grau de proteção do Aquífero Barreiras em perímetros sob fertilização química a partir de dados hidrogeofísicos - área da bacia do Rio Catu-RN

The use of chemical fertilization in arable perimeters provides increased productivity, though it can eventually lead to a qualitative depreciation of groundwater sources, especially if such sources are unconfined in nature. In this context, this thesis presents results from an analysis of the level of natural protection of the Barreiras Aquifer in an area located on the eastern coast of the Rio Grande do Norte State - Brazil. Such an aquifer is clastic in nature and has an unconfined hydraulic character, which clearly makes it susceptible to contamination from surface ground loads with contaminants associated with the leaching of excess fertilizers not absorbed by ground vegetation. The methodology used was based on the use of hydro-geophysical data, particularly inverse models of vertical electrical soundings (VES) and information from well profiles, allowing the acquisition of longitudinal conductance cartographies (S), data in mili-Siemens (mS), and the vulnerability of the aquifer. Such maps were prepared with emphasis to the unsaturated overlying zone, highlighting in particular its thickness and occurrence of clay lithologies. Thus, the longitudinal conductance and aquifer vulnerability reveal areas more susceptible to contamination in the northeast and east-central sections of the study area, with values equal to or less than 10mS and greater than or equal to 0,50, respectively. On the other hand, the southwestern section proved to be less susceptible to contamination, whose longitudinal conductance and vulnerability indices are greater than or equal to 30mS and less than or equal to 0,40, respectively.

Análise do grau de proteção do Aquífero Barreiras em perímetros sob fertilização química a partir de dados hidrogeofísicos - área da bacia do Rio Catu-RN

The use of chemical fertilization in arable perimeters provides increased productivity, though it can eventually lead to a qualitative depreciation of groundwater sources, especially if such sources are unconfined in nature. In this context, this thesis presents results from an analysis of the level of natural protection of the Barreiras Aquifer in an area located on the eastern coast of the Rio Grande do Norte State - Brazil. Such an aquifer is clastic in nature and has an unconfined hydraulic character, which clearly makes it susceptible to contamination from surface ground loads with contaminants associated with the leaching of excess fertilizers not absorbed by ground vegetation. The methodology used was based on the use of hydro-geophysical data, particularly inverse models of vertical electrical soundings (VES) and information from well profiles, allowing the acquisition of longitudinal conductance cartographies (S), data in mili-Siemens (mS), and the vulnerability of the aquifer. Such maps were prepared with emphasis to the unsaturated overlying zone, highlighting in particular its thickness and occurrence of clay lithologies. Thus, the longitudinal conductance and aquifer vulnerability reveal areas more susceptible to contamination in the northeast and east-central sections of the study area, with values equal to or less than 10mS and greater than or equal to 0,50, respectively. On the other hand, the southwestern section proved to be less susceptible to contamination, whose longitudinal conductance and vulnerability indices are greater than or equal to 30mS and less than or equal to 0,40, respectively.

Estudo da injeção de água e gás em um reservatório com características do pré-sal brasileiro

The pre-salt province is composed by large amounts of light oil and with good quality, a reality that puts Brazil in a strategic position facing the great demand for energy worldwide. In this province are the largest discoveries in the world in the last ten years; areas as Libra, Franco and Lula field, everyone containing volumes greater than 8 billion recoverable oil barrels. To develop and optimize the production of these fields, a study was done for choosing the improved oil recovery methods. The main motivations were the presence of carbon dioxide (CO2) as a contaminant and the strategic decision of do not discard it, combined with high GOR (gas-oil ratio) of the reservoir fluid. The method should take advantage of the unique abundant resources: seawater and produced gas. This way, the process of matching these resources in the water alterning gas injection (WAG) became a good option. In this master’s dissertation, it was developed a reservoir model with average characteristics of the Brazilian pre-salt, where was applied the improved oil recovery method of water alternating gas. The production of this reservoir was analyzed by parameters as: the first fluid injected in the injection process, position of the injection wells completion, injection water and gas rate and cycle time. The results showed a good performance of the method, with up to 26% of gains in the recovery factor regarding the primary recovery, since the application of water injection and gas, individually, was not able to overcome 10 % of gain. The most influential parameter found in the results was the cycle time, with higher recovery factor values obtained with the use of shorter times.

Estudo de tensoativos na organofilização de argila bentonítica para uso em fluido de perfuração à base de óleo

Due to the great challenges encountered in drilling wells, there is a need to develop fluids with appropriated properties and able to meet all the requirements of drilling operations. The physicochemical and rheological properties must be carefully controlled so that a fluid can exercise all its functions. In perforations sensitive to contact with water and "offshore", it becomes necessary the use of oil based drilling fluids, but the bentonite clay cannot be used without a previous surface modification so that their surfaces become hydrophobic. Lately, the oil companies in Brazil use imported organoclays in the preparation of oil-based drilling fluids. The study aimed to modify a calcium clay to increase the affinity of the same organic phase of oil-based drilling fluids, applying three surfactants (OCS, CTAB and UTM 150) at different concentrations. The results indicated that the surfactants UTM 150 and CTAB showed better results compared to OCS. Considering the type of surfactant and concentration as variables used in the statistical analysis, the results indicated that only the surface tension and concentration of calcium oxide in response to organophilization process showed statistically significant effects. The organophilizated clay has potential for application in oil-based drilling fluids.

Evolução morfotectônica da porção centro-sul da Bacia Paraíba

Recent endogenous processes provide dynamic movements in the lithosphere and generate the varied forms of relief, even in areas of passive continental margins, such as the research area of this work located in northeastern Brazil. The reactivation of Precambrian basement structures, after the breakup between South America and Africa in the Cretaceous played an important role in the evolution of basins, which provided generated forms of relief. These morphodynamic characteristics can be easily observed in marginal basins that exhibit strong evidence fault reactivations. The purpose of this study is to investigate the influence of morphotectonic processes in the landscape structuring of Paraíba Basin. Therefore, we used aeromagnetic, high–resolution images of the Shuttle Radar Topographic Mission–SRTM, structural geological data, deep well data and geological field data. Based on the results of the data was observed that some preexisting structures in the crystalline basement coincide with magnetic and topographic lineaments interpreted as fault reactivation of the Post–Miocene units in the Paraíba Basin. Faults that offset lithostratigraphic units provided evidence that tectonic activity associated with the deposition and erosion in the Paraíba Basin occurred from Cretaceous to the Quaternary. The neotectonic activity that occurred in Paraíba Basin was able to influence the deposition of sedimentary units and landforms. It indicates that the deposition of post–Cretaceous units was influenced by reactivation of Precambrian basement structures in this part of the Brazilian continental margin.

SISAL - Um sistema supervisório para elevação artificial de petróleo

MEDEIROS, Adelardo A. D. et al. SISAL - Um Sistema Supervisório para Elevação Artificial de Petróleo. In: Rio Oil and Gas Expo Conference, 2006, Rio de Janeiro, RJ. Anais... Rio de Janeiro, 2006.

Protocolos para a colocação e remoção de espigões

A utilização de espigões em dentes tratados endodonticamente é um dos temas mais estudados em Medicina Dentária. As opiniões são divergentes em relação aos procedimentos clínicos e materiais a serem utilizados para a colocação e remoção de espigões. O objetivo deste trabalho foi realizar uma revisão bibliográfica de forma a organizar conceitos e princípios clínicos para melhor esclarecer os fatores que determinam a necessidade de colocação, utilização e escolha do tipo de espigão, sua cimentação e técnicas para a remoção. Foram analisadas as características e propriedades dos cimentos de fosfato de zinco, ionômero de vidro, cimentos resinosos de polimerização química, polimerização dupla, foto-polimerizável e os sistemas adesivos etch and rinse, self etch e autoadesivos, bem como as técnicas para a remoção de espigões cimentados com diferentes cimentos e sistemas adesivos para depois acessar o remanescente de guta percha para o retratamento endodôntico. Foi feita uma pesquisa bibliográfica na base de dados electrónica PubMed, Google Scholar e RCAAP com as seguintes palavras chave: “Espigões”; “Retratamento Endodôntico”; “Ionómero de Vidro”; “Fosfato de Zinco”; “Cimentos Resinosos”; “Posts”; “Endodontic Retreatment”; “Glass Ionomer”; Zinc-phosphate”; “Resin Cements"; “Push Out Test”; “Posts AND Removal”. Concluiu-se que a cimentação de espigões pré-fabricados de fibra de vidro com cimentos resinosos de dupla polimerização associados aos sistemas adesivos self etch estão gradualmente substituindo os outros tipos de espigões e demais cimentos e possibilitam restaurar o dente de forma adequada e duradoura. E o uso de ultrassons apresenta maior eficácia e segurança na remoção dos espigões.

SISAL - Um sistema supervisório para elevação artificial de petróleo

MEDEIROS, Adelardo A. D. et al. SISAL - Um Sistema Supervisório para Elevação Artificial de Petróleo. In: Rio Oil and Gas Expo Conference, 2006, Rio de Janeiro, RJ. Anais... Rio de Janeiro, 2006.

Produção enzimática de biodiesel a partir de resíduos agro-industriais usando a lipase imobilizada de origem microbiana

Trabalho Final de Mestrado para obtenção do grau de Mestre em Engenharia Química e Biológica

Análise e modelagem do escoamento transitório de fluidos de perfuração

Drilling fluids present a thixotropic behavior and they usually gel when at rest. The sol-gel transition is fundamental to prevent the deposit of rock fragments, generated by drilling the well, over the drill bit during eventual stops. Under those conditions, high pressures are then required in order to break-up the gel when circulation is resumed. Moreover, very high pressures can damage the rock formation at the bottom of the well. Thus, a better understanding of thixotropy and the behavior of thixotropic materials becomes increasingly important for process control. The mechanisms that control thixotropy are not yet well defined and modeling is still a challenge. The objective of this work is to develop a mathematical model to study the pressure transmission in drilling fluids. This work presents a review of thixotropy and of different mathematical models found in the literature that are used to predict such characteristic. It also shows a review of transient flows of compressible fluids. The problem is modeled as the flow between the drillpipe and the annular region (space between the wall and the external part of the drillpipe). The equations that describe the problem (mass conservation, momentum balance, constitutive and state) are then discretized and numerically solved by using a computational algorithm in Fortran. The model is validated with experimental and numerical data obtained from the literature. Comparisons between experimental data obtained from Petrobras and calculated by three viscoplastic and one pseudoplastic models are conducted. The viscoplastic fluids, due to the yield stress, do not fully transmit the pressure to the outlet of the annular space. Sensibility analyses are then conducted in order to evaluate the thixotropic effect in pressure transmission.