Temperature characteristics of the billet and the dies in a small batch forging production

The work reported herein is part of an on-going programme to develop a computer code which, given the geometrical, process and material parameters of the forging operation, is able to predict the die and the billet cooling/heating characteristics in forging production. The code has been experimentally validated earlier for a single forging cycle and is now validated for a small batch production. To facilitate a step-by-step development of the code, the billet deformation has so far been limited to its surface layers, a situation akin to coining. The code has been used here to study the effects of die preheat-temperature, machine speed and rate of deformation the cooling/heating of the billet and the dies over a small batch of 150 forgings. The study shows: that there is a pre-heat temperature at which the billet temperature changes little from one forging to the next; that beyond a particular number of forgings, the machine speed ceases to have any pronounced influence on the temperature characteristics of the billet; and that increasing the rate of deformation reduces the heat loss from the billet and gives the billet a stable temperature profile with respect to the number of forgings. The code, which is simple to use, is being extended to bulk-deformation problems. Given a practical range of possible machine, billet and process specifics, the code should be able to arrive at a combination of these parameters which will give the best thermal characteristics of the die-billet system. The code is also envisaged as being useful in the design of isothermal dies and processes.

Risk management strategies using seasonal climate forecasting in irrigated cotton production: a tale of stochastic dominance.

Decision-making in agriculture is carried out in an uncertain environment with farmers often seeking information to reduce risk. As a result of the extreme variability of rainfall and stream-flows in north-eastern Australia, water supplies for irrigated agriculture are a limiting factor and a source of risk. The present study examined the use of seasonal climate forecasting (SCF) when calculating planting areas for irrigated cotton in the northern Murray Darling Basin. Results show that minimising risk by adjusting plant areas in response to SCF can lead to significant gains in gross margin returns. However, how farmers respond to SCF is dependent on several other factors including irrigators’ attitude towards risk.

Milk Production Responses to Oversowing a Portion of Tropical Grass Pasture with Summer Crop Legumes on Sub-tropical Dairy Farms

Northern Australian dairy farms have a large area of tropical dryland grass pasture available for use as summer pastures. Late summer-autumn in sub-tropical Australia is traditionally a difficult period in which to produce milk because of the decline in both quality and quantity of tropical grasses (Ehrlich et al. 1994). Options to improve autumn feed on dairy farms include introducing forage crops and conservation, increasing concentrate feeding and introducing legumes. Perennial tropical legumes have not been successful at this time of year because of their inability to sustain stocking rates above one cow/ha. This experiment, conducted on farms, was designed to test if annual crop legumes could be successfully oversown into tropical grass areas using minimal till methods to measure the subsequent impact on milk production on farms. Previous experiments using annual legumes in plots at Mutdapilly Research Station had demonstrated yields up to 10 t/ha can be achieved using annual tropical legumes with protein levels as high as 20% in the whole legume plant. Animal production for a consuming world : proceedings of 9th Congress of the Asian-Australasian Association of Animal Production Societies [AAAP] and 23rd Biennial Conference of the Australian Society of Animal Production [ASAP] and 17th Annual Symposium of the University of Sydney, Dairy Research Foundation, [DRF]. 2-7 July 2000, Sydney, Australia.

Genetic Parameters for Production Traits in Queensland Merinos

Genetic and phenotypic parameters are presented for production traits, greasy fleece weight (GFW), yield (YLD), clean fleece weight (CFW), average fibre diameter (DIAM) and liveweight (LWT), in 15 month old medium Peppin Merino sheep at Longreach and Julia Creek, Queensland. Heritabilities for GFW, YLD, CFW, DIAM and LWT were respectively 0.35, 0.62, 0.34, 0.74, and 0.37 for Longreach and 0.23, 0.52, 0.20, 0.67 and 0.56 for Julia Creek. Most estimates were consistent with other reported values. AAABG 13th Conference; Proceedings of the Association for the Advancement of Animal Breeding and Genetics.

Sperm production rates in Bos indicus strain bulls

Materials and Methods. Testes were collected a t castration or a t slaughter from purebred Brahman (B); Brahman cross (BX - half and three quarter); Sahiwal cross (SX – three quarter and seven eighths); and purebred and three quarter Santa Gertrudis (SG) bulls of known ages between 19 and 27 months and drawn from herds in northern coastal Queensland. 13th Biennial Conference. August 1980, Perth Western Australia.

Leveraging Lean Production Philosophy for Rationalising a Non-Linear Representation of Construction Specifications

This paper presents an approach, based on Lean production philosophy, for rationalising the processes involved in the production of specification documents for construction projects. Current construction literature erroneously depicts the process for the creation of construction specifications as a linear one. This traditional understanding of the specification process often culminates in process-wastes. On the contrary, the evidence suggests that though generalised, the activities involved in producing specification documents are nonlinear. Drawing on the outcome of participant observation, this paper presents an optimised approach for representing construction specifications. Consequently, the actors typically involved in producing specification documents are identified, the processes suitable for automation are highlighted and the central role of tacit knowledge is integrated into a conceptual template of construction specifications. By applying the transformation, flow, value (TFV) theory of Lean production the paper argues that value creation can be realised by eliminating the wastes associated with the traditional preparation of specification documents with a view to integrating specifications in digital models such as Building Information Models (BIM). Therefore, the paper presents an approach for rationalising the TFV theory as a method for optimising current approaches for generating construction specifications based on a revised specification writing model.

Kirjan tie lukijalle : Kirjakauppojen vakiintuminen Suomessa 1740 - 1860

Books Paths to Readers describes the history of the origins and consolidation of modern and open book stores in Finland 1740 1860. The thesis approaches the book trade as a part of a print culture. Instead of literary studies choice to concentrate on texts and writers, book history seeks to describe the print culture of a society and how the literary activities and societies interconnect. For book historians, printed works are creations of various individuals and groups: writers, printers, editors, book sellers, censors, critics and finally, readers. They all take part in the creation, delivery and interpretation of printed works. The study reveals the ways selling and distributing books have influenced the printed works and the literary and print culture. The research period 1740 1860 covers the so-called second revolution of the book, or the modernisation of the print culture. The thesis describes the history of 60 book stores and their 96 owners. The study concentrates on three themes: firstly, how the particular book trade network became a central institution for printed works distribution, secondly what were the relations between cosmopolitan European book markets and the national cultural sphere, and thirdly how book stores functioned as cultural institutions and business enterprises. Book stores that have a varied assortment and are targeted to all readers became the main institution for book trade in Finland during 1740 1860. It happened because of three features. First, the book binders monopoly on selling bound copies in Sweden was abolished in 1740s. As a consequence entrepreneurs could concentrate solely to trade activities and offer copies from various publishers at their stores. Secondly the common business model of bartering was replaced by selling copies for cash, first in the German book trade centre Leipzig in 1770s. The change intensified book markets activities and Finnish book stores foreign connections. Thirdly, after Finland was annexed to the Russian empire in 1809, the Grand duchy s administration steered foreign book trade to book stores (because of censorship demands). Up to 1830 s book stores were available only in Helsinki and Turku. During next ten years book stores opened in six regional centres. The early entrepreneurs ran usually vertical businesses consisting of printing, publishing and distribution activities. This strategy lowered costs, eased the delivery of printed works and helped to create elaborated centres for all book activities. These book stores main clientele consisted of the Swedish speaking gentry. During late 1840s various opinion leaders called for the development of a national Finnish print culture, and also book stores. As a result, during the five years before the beginning of the Crimean war (1853 1856) book stores were opened in almost all Finnish towns: at the beginning of the war 36 book stores operated in 21 towns. The later book sellers, mainly functioning in small towns among Finnish speaking people, settled usually strictly for selling activities. Book stores received most of their revenues from selling foreign titles. Swedish, German, French and Belgian (pirate editions of popular French novels) books were widely available for the multilingual gentry. Foreign titles and copies brought in most of the revenues. Censorship inspections or unfavourable custom fees would not limit the imports. Even if the local Finnish print production steadily rose, many copies, even titles, were never delivered via book stores. Only during the 1840 s and 1850 s the most advanced publishers would concentrate on creating publishing programmes and delivering their titles via book stores. Book sellers regulated commissions were small. They got even smaller because of large amounts of unsold copies, various and usual misunderstandings of consignments and accounts or plain accidents that destroyed shipments and warehouses. Also, the cultural aim of a creating large and assortments and the tendency of short selling periods demanded professional entrepreneurship, which many small town book sellers however lacked. In the midst of troublesome business efforts, co-operation and mutual concern of the book market s entrepreneurs were the key elements of the trade, although on local level book sellers would compete, sometimes even ferociously. The difficult circumstances (new censorship decree of 1850, Crimean war) and lack of entrepreneurship, experience and customers meant that half of the book stores opened in 1845 1860 was shut in less than five years. In 1858 the few leading publishers established The Finnish Book Publishers Association. Its first task was to create new business rules and manners for the book trade. The association s activities began to professionalise the whole network, but at the same time the earlier independence of regional publishing and selling enterprises diminished greatly. The consolidation of modern and open book store network in Finland is a history of a slow and complex development without clear signs of a beginning or an end. The ideal book store model was rarely accomplished in its all features. Nevertheless, book stores became the norm of the book trade. They managed to offer larger selections, reached larger clienteles and maintained constant activity better than any other book distribution model. In essential, the book stores methods have not changed up to present times.

Production of microalgal concentrates by flocculation and their assessment as aquaculture feeds

A novel technique was developed for the flocculation of marine microalgae commonly used in aquaculture. The process entailed an adjustment of pH of culture to between 10 and 10.6 using NaOH, followed by addition of a non-ionic polymer Magnafloc LT-25 to a final concentration of 0.5 mg L-1. The ensuing flocculate was harvested, and neutralised giving a final concentration factor of between 200- and 800-fold. This process was successfully applied to harvest cells of Chaetoceros calcitrans, C. muelleri, Thalassiosira pseudonana, Attheya septentrionalis, Nitzschia closterium, Skeletonema sp., Tetraselmis suecica and Rhodomonas salina, with efficiencies >=80%. The process was rapid, simple and inexpensive, and relatively cost neutral with increasing volume (cf. concentration by centrifugation). Harvested material was readily disaggregated to single cell suspensions by dilution in seawater and mild agitation. Microscopic examination of the cells showed them to be indistinguishable from corresponding non-flocculated cells. Chlorophyll analysis of concentrates prepared from cultures of Concentrates of T. pseudonana prepared using pH-induced flocculation gave better growth of juvenile Pacific oysters (Crassostrea gigas) than concentrates prepared by ferric flocculation, or centrifuged concentrates using a cream separator or laboratory centrifuge. In follow up experiments, concentrates prepared from 1000 L Chaetoceros muelleri cultures were effective as supplementary diets to improve the growth of juvenile C. gigas and the scallop Pecten fumatus reared under commercial conditions, though not as effective as the corresponding live algae. The experiments demonstrated a proof-of-concept for a commercial application of concentrates prepared by flocculation, especially for use at a remote nursery without on-site mass-algal culture facilities.

Feeding sorghum ergot (Claviceps africana) to sows before farrowing inhibits milk production

Objective: To assess the impact of feeding different amounts of sorghum ergot to sows before farrowing. Design: Fifty-one pregnant sows from a continually farrowing piggery were sequentially inducted into the experiment each week in groups of four to seven, as they approached within 14 days of farrowing. Diets containing sorghum ergot sclerotia within the range of 0 (control) up to 1.5% w/w (1.5% ergot provided 7 mg alkaloids/kg, including 6 mg dihydroergosine/kg) were randomly allocated and individually fed to sows. Ergot concentrations were varied with each subsequent group until an acceptable level of tolerance was achieved. Diets with ergot were replaced with control diets after farrowing. Post-farrowing milk production was assessed by direct palpation and observation of udders, and by piglet responses and growth. Blood samples were taken from sows on three days each week, for prolactin estimation. Results: Three sows fed 1.5% ergot for 6 to 10 days preceding farrowing produced no milk, and 87% of their piglets died despite supplementary feeding of natural and artificial colostrums, milk replacer, and attempts to foster them onto normally lactating sows. Ergot inclusions of 0.6% to 1.2% caused lesser problems in milk release and neo-natal piglet mortality. Of 23 sows fed either 0.3% or 0.6% ergot, lactation of only two first-litter sows were affected. Ergot caused pronounced reductions in blood prolactin, and first-litter sows had lower plasma prolactin than multiparous sows, increasing their susceptibility to ergot. Conclusion: Sorghum ergot should not exceed 0.3% (1 mg alkaloid/kg) in diets of multiparous sows fed before farrowing, and should be limited to 0.1 % for primiparous sows, or avoided completely.

Modelling Leaf Production and Crop Development in Maize (Zea mays L.) After Tassel Initiation Under Diverse Conditions of Temperature and Photoperiod

Prediction of the initiation, appearance and emergence of leaves is critically important to the success of simulation models of crop canopy development and some aspects of crop ontogeny. Data on leaf number and crop ontogeny were collected on five cultivars of maize differing widely in maturity and genetic background grown under natural and extended photoperiods, and planted on seven sowing dates from October 1993 to March 1994 at Gatton, South-east Queensland. The same temperature coefficients were established for crop ontogeny before silking, and the rates of leaf initiation, leaf tip appearance and full leaf expansion, the base, optimum and maximum temperatures for each being 8, 34 and 40 degrees C. After silking, the base temperature for ontogeny was 0 degrees C, but the optimum and maximum temperatures remained unchanged. The rates of leaf initiation, appearance of leaf tips and full leaf expansion varied in a relatively narrow range across sowing times and photoperiod treatments, with average values of 0.040 leaves (degrees Cd)-1, 0.021 leaves (degrees Cd)-1, and 0.019 leaves (degrees Cd)-1, respectively. The relationships developed in this study provided satisfactory predictions of leaf number and crop ontogeny (tassel initiation to silking, emergence to silking and silking to physiological maturity) when assessed using independent data from Gatton (South eastern Queensland), Katherine and Douglas Daly (Northern Territory), Walkamin (North Queensland) and Kununurra (Western Australia).

Poisoning for production: how effective is fox baiting in south-eastern Australia?

1. The European red fox Vulpes vulpes represents a continuing threat to both livestock and native vertebrates in Australia, and is commonly managed by setting ground-level baits impregnated with 1080 (sodium fluoroacetate) poison. However, the long-term effectiveness of such control campaigns is likely to be limited due to the ability of foxes to disperse over considerable distances and to swiftly recolonize areas from where they had been removed. 2. To investigate the effectiveness of fox baiting in a production landscape, we assessed the potential for foxes to reinvade baited farm property areas within the jurisdiction of the Molong Rural Lands Protection Board (RLPB), an area of 815 000 ha on the central tablelands of New South Wales, Australia. The spatial distribution and timing of fox baiting campaigns between 1998 and 2002 was estimated from RLPB records and mapped using Geographical Information System software. The effectiveness of the control campaign was assessed on the basis of the likely immigration of foxes from non-baited farms using immigration distances calculated from published relationships between dispersal distance and home range size. 3. Few landholders undertook baiting campaigns in any given year, and the area baited was always so small that no baited property would have been sufficiently far from an unbaited property to have been immune from immigrating individuals. It is likely, therefore, that immigration onto farms negated any long-term effects of baiting operations. This study highlights some of the key deficiencies in current baiting practices in south-eastern Australia and suggests that pest management programmes should be monitored using such methods to ensure they achieve their goals.

Strategic Analysis: A key factor in developing horticultural supply chains in transitional Asian economies

Globalisation is set to have a major impact on world horticultural production and distribution of fruit and vegetables throughout the world. In contrast to developing countries such as China, production and consumption of fresh fruit and vegetables in most developed countries is relatively static. For developed countries, we are starting to see consolidation in the number of farms producing fruit and vegetables with falling or static prices and real farm incomes. Global supply chains are now dominated by a few large multi-national retailers supplied by preferred trans-national distribution companies. The major competitive advantages that are emerging are consistency of supply of high quality product over an extended season and the control of genetic resources and their marketing. To capture these new competitive advantages, new strategic analyses and planning processes must be implemented. In the past, strategic analyses and planning has been undertaken on an ad hoc basis without accurate global intelligence. In the future, working ‘on the supply chain’ will become equally, if not more important, than working ‘in the supply chain’. A revised approach to strategic planning, which encompasses and adjusts for the changes caused by globalisation, is urgently needed. A new 6-step strategic analyses process is described.

Subsoil constraints to grain production in the cropping soils of the north-eastern region of Australia: an overview

In dryland agricultural systems of the subtropical, semi-arid region of north-eastern Australia, water is the most limiting resource. Crop productivity depends on the efficient use of rainfall and available water stored in the soil during fallow. Agronomic management practices including a period of fallow, stubble retention, and reduced tillage enhance reserves of soil water. However, access to stored water in these soils may be restricted by the presence of growth-limiting conditions in the rooting zone of the crop. These have been termed as subsoil constraints. Subsoil constraints may include compacted or gravel layers (physical), sodicity, salinity, acidity, nutrient deficiencies, presence of toxic elements (chemical) and low microbial activity (biological). Several of these constraints may occur together in some soils. Farmers have often not been able to obtain the potential yield determined by their prevailing climatic conditions in the marginal rainfall areas of the northern grains region. In the past, the adoption of soil management practices had been largely restricted to the top 100 mm soil layer. Exploitation of the subsoil as a source of water and nutrients has largely been overlooked. The key towards realising potential yields would be to gain better understanding of subsoils and their limitations, then develop options to manage them practically and economically. Due to the complex nature of the causal factors of these constraints, efforts are required for a combination of management approaches rather than individual options, with the aim to combat these constraints for sustainable crop production, managing natural resources and avoiding environmental damage.

Biological control of parthenium (Parthenium hysterophorus) in Australian rangeland translates to improved grass production.

Biological control of parthenium, a major weed in grazing areas in Australia, was initiated in the mid 1970s. Since then, nine species of insects and two rust fungi have been introduced. Evaluation using pesticide exclusion at two sites (Mt. Panorama and Plain Creek) in Queensland, Australia, revealed that classical biological control had a significant negative effect on the target weed, but the impact varied between years. In this study, I quantified the effects of biological control of parthenium on grass production. Grass production declined with the increase in parthenium biomass. Significant increase in grass production due to biological control was observed, but only in 1 of 4 yr at Mt. Panorama and 2 of 4 yr at Plain Creek. At Mt. Panorama, there was a 40% increase in grass biomass in 1997 because of defoliation by Zygogramma bicolorata and galling by Epiblema strenuana. At Plain Creek, grass biomass increased by 52% in 1998 because of E. strenuana and by 45% in 2000 because of combined effects of E. strenuana and the summer rust Puccinia melampodii. This study provides evidence on the beneficial effects of biological control of parthenium in areas under limited grazing.

Effect of irrigation amounts applied with subsurface drip irrigation on corn evapotranspiration, yield, water use efficiency, and dry matter production in a semiarid climate

Quantifying the local crop response to irrigation is important for establishing adequate irrigation management strategies. This study evaluated the effect of irrigation applied with subsurface drip irrigation on field corn (Zea mays L.) evapotranspiration (ETc), yield, water use efficiencies (WUE = yield/ETc, and IWUE = yield/irrigation), and dry matter production in the semiarid climate of west central Nebraska. Eight treatments were imposed with irrigation amounts ranging from 53 to 356 mm in 2005 and from 22 to 226 mm in 2006. A soil water balance approach (based on FAO-56) was used to estimate daily soil water and ETc. Treatments resulted in seasonal ETc of 580-663 mm and 466-656 mm in 2005 and 2006, respectively. Yields among treatments differed by as much as 22% in 2005 and 52% in 2006. In both seasons, irrigation significantly affected yields, which increased with irrigation up to a point where irrigation became excessive. Distinct relationships were obtained each season. Yields increased linearly with seasonal ETc (R 2 = 0.89) and ETc/ETp (R 2 = 0.87) (ETp = ETc with no water stress). The yield response factor (ky), which indicates the relative reduction in yield to relative reduction in ETc, averaged 1.58 over the two seasons. WUE increased non-linearly with seasonal ETc and with yield. WUE was more sensitive to irrigation during the drier 2006 season, compared with 2005. Both seasons, IWUE decreased sharply with irrigation. Irrigation significantly affected dry matter production and partitioning into the different plant components (grain, cob, and stover). On average, the grain accounted for the majority of the above-ground plant dry mass (≈59%), followed by the stover (≈33%) and the cob (≈8%). The dry mass of the plant and that of each plant component tended to increase with seasonal ETc. The good relationships obtained in the study between crop performance indicators and seasonal ETc demonstrate that accurate estimates of ETc on a daily and seasonal basis can be valuable for making tactical in-season irrigation management decisions and for strategic irrigation planning and management.