红松和长白松针叶暗呼吸对连续4个生长季高浓度CO_2处理的响应

以开顶箱法研究了高浓度CO2对长白山两种针叶树—红松和长白松针叶暗呼吸作用的长期影响.对两个树种连续4个生长季进行700和500μmol·mol-1CO2处理,同时设接受大气CO2浓度(约350μmol·mol-1CO2)的开顶箱为对照,在CO2处理的第2,3和4个生长季分别测定了针叶的暗呼吸速率.结果表明:CO2处理的第2个生长季,高浓度CO2下红松和长白松针叶暗呼吸速率增加,可能与碳氮含量变化有关;CO2处理的第3个生长季,高浓度CO2条件下生长的红松针叶暗呼吸速率增加,长白松针叶的暗呼吸速率下降,两树种呈不同响应主要与植株的生长速率不同有关;CO2处理的第4个生长季,红松和长白松针叶的暗呼吸速率均受高浓度CO2抑制.第3个生长季通过改变测量CO2浓度,发现高浓度CO2对长白松针叶暗呼吸作用的短期效应与长期效应呈现一致性,红松不完全相同.红松和长白松针叶的暗呼吸作用对高浓度CO2的响应与CO2处理时间及植株个体的生长发育阶段有关,暗呼吸速率的变化是CO2直接作用与长期驯化共同作用的结果,不能用短期的测定结果预测针叶暗呼吸对高浓度CO2响应的长期效应.

辽东山区3种次生林群落土壤酶活性的季节动态

研究了辽东山区蒙古栎(Quercus mongolica)、杂木林、胡桃楸(Juglans mandshurica)3种次生林群落土壤转化酶、淀粉酶、脱氢酶和过氧化氢酶活性的季节变化规律。结果表明:次生林群落土壤酶活性均呈明显的垂直分布特性,即随土壤深度的增加,酶活性逐渐降低。次生林群落土壤酶活性具有明显的季节变化特点,不同群落酶活性变化趋势不同,其中蒙古栎林的土壤转化酶、淀粉酶和脱氢酶活性最高,胡桃楸林最低,但胡桃楸林过氧化氢酶活性相对最大。4种酶活性在不同群落间差异均达到显著水平(P<0.05),这可能与植被类型、凋落物的多样性或植物根系分泌物的不同有关。

中国东北落叶松属3种植物潜在分布对气候变化的敏感性分析

该文在东北地区多年平均的年均温、年降水分布图,海拔高程图、坡度图、坡向图和植被图的基础上,使用地理信息系统和Logistic回归模型的结合,预测3种落叶松(Larixsp.)的"气候-地形"潜在分布区。预测精度用敏感性、指定度和总正确率进行评价,3个树种的敏感性为61%~88%,指定度为80%~99.8%,总正确率为80%~99.8%。年均温、年降水和海拔是控制3种落叶松分布的主要环境因子。采用5种气温变化方案(+1℃、+2℃、+3℃、+4℃和+5℃)和6种降水变化方案(-30%、-20%、-10%、+10%、+20%和+30%),预测气候变化对各个树种潜在分布的影响,探索不同的树种对气候因子的敏感性。结果表明,气温每上升1℃,兴安落叶松(Larixgmelinii)将减少12%;长白落叶松(Larix olgensisvar.changpaiensis)将增加23%;华北落叶松(Larix principis-rupprecntii)将增加500%。降水每增加10%,兴安落叶松将减少12.5%;长白落叶松将增加64%;华北落叶松将减少15%;随气候的"暖干化"(+5℃,-30%),兴安落叶松将向西北方退缩100 km左右;长白落叶松向西北方扩展100 km左右;华北落叶松将向东北方扩展800 km左右。随气候的"暖湿化"(+5℃,+30%),兴安落叶松将向西北退缩400km左右;长白落叶松将向西北方扩展550 km;华北落叶松将向东北方扩展320 km左右。

Efficient One-Pot Synthesis of Highly Substituted Thiophene Library from 1,3-Dicarbonyl Compounds

A faccile and efficient one-pot synthesis of highly substituted thiophenes has been developed and employed for the preparation of a small focused library. Treatment of 1,3-dicarbonyl compounds 1 with CS2 in the presence of K2CO3 in DMF at room temperature, followed by stepwise addition of alkyl bromides 2 and methylene active bromides 3, provided via intramolecular cyclization 2,3,4,5-tetrasubstituted thiophenes 4 in yields of 77-94%. This protocol, combining construction and modification of the thiophene ring, increases the structural diversity of final products from readily available materials. A mechanism for the one-pot synthesis of thiophenes of type 4 has been proposed. A small focused library of thiophenes is prepared using the sequential addition of reagents to achieve unique substitution in the 2 and 5 position of the thiophene ring

Synthesis of isomeric bis(amine anhydride)s for novel poly(amine imide)s by Pd-catalyzed amination of 4-chlorophthalic anhydride

Two novel bis(amine anhydride) monomers, N,N'-bis(3,4-dicarboxyphenyl)-1,4-phenylenediamine dianhydride I and N,/N'-bis(3,4-dicarboxyphenyl)-1,3-phenylenediamine dianhydride 11, were prepared via palladium-catalyzed amination reaction of 4-chloro-N-methylphthaliniide with 1,4-phenylenediamine or 1,3-phenylenediamine, followed by alkaline hydrolysis of the intermediate bis(amine imide)s and subsequent dehydration of the resulting tetraacids. A series of new poly(amine imide)s were prepared from the synthesized dianhydride monomers with various diamines in NMP via conventional two-step method.

Enhanced amplified spontaneous emission by assistant Forster energy transfer in DCJTB-C545T-Alq(3) coguest-host system

Amplified spontaneous emission (ASE) characteristics of a red fluorescent dye 4-(dicyanomethylene)-2-t-butyl-6(1,1,7,7-tetramethyljulolidyl-9-enyl)-4H-pyran (DCJTB) were significantly improved by assistant Forster energy transfer. The coguest-host system was composed of an electron transport organic molecule tris(8-hydroxyquinoline) aluminum (Alq(3)) as host and a green fluorescent dye (10-(2-benzothiazolyl)-1,1,7,7-tetramethyl-2,3,6,7-tetrahydro-1H,5H,11H-[1]benzopyrano[6,7,8-ij]quinolizin-11-one) (C545T) as assistant dopant codoped with the guest red dye DCJTB as emitter in a matrix of polystyrene (PS).

The effect of annealing treatment on performance of interdiffused organic photovoltaic devices

We fabricated the interdiffused organic photovoltaic devices, which composed of poly (2-methoxy-5-(2'-ethylhexyloxy)-1, 4-phenylenevinylene) (MEH-PPV) and buckminsterfullerene (C-60), by annealing treatment. After annealing, C60 diffused into the MEH-PPV layer, in consequence, MEH-PPV/C-60 interfacial area was increased and their interface became closer proximity. The results lead to reduce reverse-bias saturation current (J(s)), and increase the open-circuit voltage (V-OC) and the short-circuit current (J(SC)).

虎眼万年青和其他3种抗癌中草药的微量元素含量及其溶出特性

目的对虎眼万年青和其他3种抗癌中草药(白花蛇舌草、半枝莲和山豆根)中16种常量和微量元素及溶出率进行比较,为阐明虎眼万年青抗癌作用提供依据。方法采用等离子体原子发射光谱法,辅以原子吸收光谱法和原子荧光光谱法进行有关检测。结果1)虎眼万年青含有多种人体必需的常量和微量元素,特别是Ca、Mg、Fe、Zn含量较高;2)虎眼万年青和其他3种中草药水煎液中Cu/Zn比值比较低;3)4种中草药水煎液中Se含量较低,差异无统计学意义。Ge在4种中草药的原生药或水煎液中的含量均较低。结论虎眼万年青可能通过调节肿瘤患者体内Cu、Zn及Ca等元素的平衡发挥其抗癌、抗炎性反应作用。

Luminescence properties of Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors prepared by spray pyrolysis process

Starting from metal nitrate aqueous solutions and H3BO3, Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors were synthesized by spray pyrolysis followed by annealing at high temperature. The obtained phosphor particles have spherical morphology with size in the range 0.5-2 mu m. Independent of the x values in Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) phosphors, the Eu3+ ion shows its characteristic D-5(0), (1)-F-7(J) (J = 0, 1, 2, 3, 4) transitions with D-5(0)-F-7(2) red emission (612 nm) as the most prominent group. The photoluminescence intensity of phosphors increases with the increase of x value in Y0.9-xGdxEu0.1Al3(BO3)(4) (0 <= x <= 0.9) due to an energy migration process like Gd3+-(Gd3+)(n)-Eu3+ that occurred in the host materials.

Synthesis of bis(amine anhydride)s for novel high T(g)s and organosoluble poly(amine imide)s by palladium-catalyzed amination of 4-chlorophthalide anhydride

Two novel bis(amine anhydride)s, NN-bis(3,4-dicarboxyphenyl)aniline dianhydride (I) and N,N-bis(3,4-dicarboxyphenyl)-p-tert-butylaniline (II), were synthesized from the palladium-catalyzed amination reaction of N-methyl-protected 4-chlorophthalic anhydride with arylamines, followed by alkaline hydrolysis of the intermediate bis(amine-phthalimide)s and subsequent dehydration of the resulting tetraacids. The X-ray structures of anhydride I and II were determined. The obtained dianhydride monomers were reacted with various aromatic diamines to produce a series of novel polyimides. Because of the incorporation of bulky, propeller-shaped triphenylamine units along the polymer backbone, all polyimides exhibited good solubility in many aprotic solvents while maintaining their high thermal properties. These polymers had glass transition temperatures in the range of 298-408 degrees C. Thermogravimetric analysis showed that all polymers were stable, with 10% weight loss recorded above 525 degrees C in nitrogen.The tough polymer films, obtained by casting from solution, had tensile strength, elongation at break, and tensile modulus values in the range of 95-164 MPa, 8.8-15.7%, and 1.3-2.2 GPa, respectively.

Synthesis and properties of novel polyimides derived from 2,2 ',3,3 '-benzophenonetetracarboxylic dianhydride

A new synthetic route to 2,2',3,3'-BTDA (where BTDA is benzophenonetetracarboxylic dianhydride), an isomer of 2,3',3',4'-BTDA and 3,3',4,4'-BTDA, is described. Single-crystal X-ray diffraction analysis of 2,2',3,3'-BTDA has shown that this dianhydride has a bent and noncoplanar structure. The polymerizations of 2,2',3,3'-BTDA with 4,4'-oxydianiline (ODA) and 4,4'-bis(4-aminophenoxy)benzene (TPEQ) have been investigated with a conventional two-step process. A trend of cyclic oligomers forming in the reaction of 2,2',3,3'-BTDA and ODA has been found and characterized with IR, NMR, matrix-assisted laser desorption/ionization time-of-flight mass spectrometry, and elemental analyses. Films based on 2,2',3,3'-BTDA/TPEQ can only be obtained from corresponding polyimide (PI) solutions prepared by chemical imidization because those from their polyamic acids by thermal imidization are brittle. PIS from 2,2',3,3'-BTDA have lower inherent viscosities and worse thermal and mechanical properties than the corresponding 2,3',3',4'-BTDA- and 3,3',4,4'-BTDA-based PIs. PIs from 2,2',3,3'-BTDA and 2,3',3',4'-BTDA are amorphous, whereas those from 3,3',4,4'-BTDA have some crystallinity, according to wide-angle X-ray diffraction.

Fabrication and luminescent properties of rare earths-doped Gd-2(WO4)(3) thin film phosphors by Pechini sol-gel process

Rare earth ions (Eu3+ and Dy3+)-doped Gd-2(WO4)(3) phosphor films were prepared by a Pechini sol-gel process. X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), atomic force microscopy (AFM) and photoluminescence (PL) spectra as well as lifetimes were used to characterize the resulting powders and films. The results of XRD indicate that the films begin to crystallize at 600degreesC and the crystallinity increases with the elevation of annealing temperatures. The film is uniform and crack-free, WO(4)(2-)mainly consists of closely packed fine particles with an average grain size of 80 nm. Owing to an energy transfer from 4 groups, the rare earth ions show their characteristic emissions in crystalline Gd-2(WO4)(3) phosphor films, i.e., D-5(J) -F-7(J), (J = 0, 1, 2, 3; J' = 0 1, 2, 3, 4, not in all cases) transitions for Eu3+ and F-4(9/2)-H-6(J) (J = 13/2, 15/2) transitions for D Y3+, with the hypersensitive transitions D-5(0)-F-7(2) (Eu3+) and F-4(9/2) - H-6(13/2) (Dy3+) being the most prominent groups, respectively.

Polyimides derived from 3,3 '-bis(N-aminophthalimide)

A novel diamine, 3,3'-bis(N-aminophthalimide) (BAPI), was prepared from 3,3'-bis(N-phenylphthalimide). Its structure was determined via IR, H-1 NMR, N-15 NMR, elemental analysis, and single-crystal X-ray diffraction analysis. A series of homo- and copolyimides were synthesized by a conventional one-step method in p-chlorophenol. The characteristic IR absorption bands of hydrazine-based imide groups were near 1780, 1750, 1350, 1100, and 730 cm(-1). The polymers showed good solubility in polar aprotic solvents and phenols at room temperature. The temperatures of 5% weight loss (T-5%) of the polyimides ranged from 495 to 530 degrees C in air. DMTA analyses indicated that the glass-transition temperatures (Tgs) of the polyimides were in the range 371-432 degrees C. These polymers had cutoff wavelengths between 350 and 400 nm. The polyimide films of 6FDA/BAPI and 4,4'-HQPDA/BAPI were colorless; other films were pale yellow or yellow.

Memory devices based on lanthanide (SM3+, EU3+, Gd3+) complexes

Memory effects in single-layer organic light-emitting devices based on Sm3+, Gd3+, and Eu3+ rare earth complexes were realized. The device structure was indium-tin-oxide (ITO)/3,4-poly(ethylenedioxythiophene)-poly(styrenesulfonate) (PEDOT)/Poly(N-vinyl carbazole) (PVK): rare earth complex/LiF/Ca/Ag. It was found experimentally that all the devices exhibited two distinctive bistable conductivity states in current-voltage characteristics by applying negative starting voltage, and more than 10(6) write-read-erase-reread cycles were achieved without degradation. Our results indicate that the rare earth organic complexes are promising materials for high-density, low-cost memory application besides the potential application as organic light-emitting materials in display devices.