The value of a small microkernel for dreamy memory and the RAMpage memory hierarchy

This paper explores potential for the RAMpage memory hierarchy to use a microkernel with a small memory footprint, in a specialized cache-speed static RAM (tightly-coupled memory, TCM). Dreamy memory is DRAM kept in low-power mode, unless referenced. Simulations show that a small microkernel suits RAMpage well, in that it achieves significantly better speed and energy gains than a standard hierarchy from adding TCM. RAMpage, in its best 128KB L2 case, gained 11% speed using TCM, and reduced energy 14%. Equivalent conventional hierarchy gains were under 1%. While 1MB L2 was significantly faster against lower-energy cases for the smaller L2, the larger SRAM's energy does not justify the speed gain. Using a 128KB L2 cache in a conventional architecture resulted in a best-case overall run time of 2.58s, compared with the best dreamy mode run time (RAMpage without context switches on misses) of 3.34s, a speed penalty of 29%. Energy in the fastest 128KB L2 case was 2.18J vs. 1.50J, a reduction of 31%. The same RAMpage configuration without dreamy mode took 2.83s as simulated, and used 2.39J, an acceptable trade-off (penalty under 10%) for being able to switch easily to a lower-energy mode.

Comparison of beam theory and finite-element analysis with in vivo bone strain data from the alligator cranium

The mechanical behavior of the vertebrate skull is often modeled using free-body analysis of simple geometric structures and, more recently, finite-element (FE) analysis. In this study, we compare experimentally collected in vivo bone strain orientations and magnitudes from the cranium of the American alligator with those extrapolated from a beam model and extracted from an FE model. The strain magnitudes predicted from beam and FE skull models bear little similarity to relative and absolute strain magnitudes recorded during in vivo biting experiments. However, quantitative differences between principal strain orientations extracted from the FE skull model and recorded during the in vivo experiments were smaller, and both generally matched expectations from the beam model. The differences in strain magnitude between the data sets may be attributable to the level of resolution of the models, the material properties used in the FE model, and the loading conditions (i.e., external forces and constraints). This study indicates that FE models and modeling of skulls as simple engineering structures may give a preliminary idea of how these structures are loaded, but whenever possible, modeling results should be verified with either in vitro or preferably in vivo testing, especially if precise knowledge of strain magnitudes is desired. (c) 2005 Wiley-Liss, Inc.

A Comparison of Methodologies from Two Longitudinal Community-Based Randomized Controlled Trials of Similar Interventions in Palliative Care: What Worked and What Did Not

Background: Methodological challenges such as recruitment problems and participant burden make clinical trials in palliative care difficult. In 2001-2004, two community-based randomized controlled trials (RCTs) of case conferences in palliative care settings were independently conducted in Australia-the Queensland Case Conferences trial (QCC) and the Palliative Care Trial (PCT). Design: A structured comparative study of the QCC and PCT was conducted, organized by known practical and organizational barriers to clinical trials in palliative care. Results: Differences in funding dictated study designs and recruitment success; PCT had 6 times the budget of QCC. Sample size attainment. Only PCT achieved the sample size goal. QCC focused on reducing attrition through gatekeeping while PCT maximized participation through detailed recruitment strategies and planned for significant attrition. Testing sustainable interventions. QCC achieved a higher percentage of planned case conferences; the QCC strategy required minimal extra work for clinicians while PCT superimposed conferences on normal work schedules. Minimizing participant burden. Differing strategies of data collection were implemented to reduce participant burden. QCC had short survey instruments. PCT incorporated all data collection into normal clinical nursing encounters. Other. Both studies had acceptable withdrawal rates. Intention-to-treat analyses are planned. Both studies included substudies to validate new outcome measures. Conclusions: Health service interventions in palliative care can be studied using RCTs. Detailed comparative information of strategies, successes and challenges can inform the design of future trials. Key lessons include adequate funding, recruitment focus, sustainable interventions, and mechanisms to minimize participant burden.

A theory for execution-time derivation in real-time programs

We provide an abstract command language for real-time programs and outline how a partial correctness semantics can be used to compute execution times. The notions of a timed command, refinement of a timed command, the command traversal condition, and the worst-case and best-case execution time of a command are formally introduced and investigated with the help of an underlying weakest liberal precondition semantics. The central result is a theory for the computation of worst-case and best-case execution times from the underlying semantics based on supremum and infimum calculations. The framework is applied to the analysis of a message transmitter program and its implementation. (c) 2005 Elsevier B.V. All rights reserved.

Detecting finite bandwidth periodic signals in stationary noise using the signal coherence spectrum

All signals that appear to be periodic have some sort of variability from period to period regardless of how stable they appear to be in a data plot. A true sinusoidal time series is a deterministic function of time that never changes and thus has zero bandwidth around the sinusoid's frequency. A zero bandwidth is impossible in nature since all signals have some intrinsic variability over time. Deterministic sinusoids are used to model cycles as a mathematical convenience. Hinich [IEEE J. Oceanic Eng. 25 (2) (2000) 256-261] introduced a parametric statistical model, called the randomly modulated periodicity (RMP) that allows one to capture the intrinsic variability of a cycle. As with a deterministic periodic signal the RMP can have a number of harmonics. The likelihood ratio test for this model when the amplitudes and phases are known is given in [M.J. Hinich, Signal Processing 83 (2003) 1349-13521. A method for detecting a RMP whose amplitudes and phases are unknown random process plus a stationary noise process is addressed in this paper. The only assumption on the additive noise is that it has finite dependence and finite moments. Using simulations based on a simple RMP model we show a case where the new method can detect the signal when the signal is not detectable in a standard waterfall spectrograrn display. (c) 2005 Elsevier B.V. All rights reserved.

Perceptual speed does not cause intelligence, and intelligence does not cause perceptual speed

There is ongoing debate whether the efficiency of local cognitive processes leads to global cognitive ability or whether global ability feeds the efficiency of basic processes. A prominent example is the well-replicated association between inspection time (IT), a measure of perceptual discrimination speed, and intelligence (IQ), where it is not known whether increased speed is a cause or consequence of high IQ. We investigated the direction of causation between IT and IQ in 2012 genetically related subjects from Australia and The Netherlands. Models in which the reliable variance of each observed variable was specified as a latent trait showed IT correlations of -0.44 and -0.33 with respective Performance and Verbal IQ; heritabilities were 57% (IT), 83% (PIQ) and 77% (VIQ). Directional causation models provided poor fits to the data, with covariation best explained by pleiotropic genes (influencing variation in both IT and IQ). This finding of a common genetic factor provides a better target for identifying genes involved in cognition than genes which are unique to specific traits.

Off-line signature verification and forgery detection using fuzzy modeling

Automatic signature verification is a well-established and an active area of research with numerous applications such as bank check verification, ATM access, etc. This paper proposes a novel approach to the problem of automatic off-line signature verification and forgery detection. The proposed approach is based on fuzzy modeling that employs the Takagi-Sugeno (TS) model. Signature verification and forgery detection are carried out using angle features extracted from box approach. Each feature corresponds to a fuzzy set. The features are fuzzified by an exponential membership function involved in the TS model, which is modified to include structural parameters. The structural parameters are devised to take account of possible variations due to handwriting styles and to reflect moods. The membership functions constitute weights in the TS model. The optimization of the output of the TS model with respect to the structural parameters yields the solution for the parameters. We have also derived two TS models by considering a rule for each input feature in the first formulation (Multiple rules) and by considering a single rule for all input features in the second formulation. In this work, we have found that TS model with multiple rules is better than TS model with single rule for detecting three types of forgeries; random, skilled and unskilled from a large database of sample signatures in addition to verifying genuine signatures. We have also devised three approaches, viz., an innovative approach and two intuitive approaches using the TS model with multiple rules for improved performance. (C) 2004 Pattern Recognition Society. Published by Elsevier Ltd. All rights reserved.

Optimal control and operation of drum granulation processes

Process optimisation and optimal control of batch and continuous drum granulation processes are studied in this paper. The main focus of the current research has been: (i) construction of optimisation and control relevant, population balance models through the incorporation of moisture content, drum rotation rate and bed depth into the coalescence kernels; (ii) investigation of optimal operational conditions using constrained optimisation techniques; (iii) development of optimal control algorithms based on discretized population balance equations; and (iv) comprehensive simulation studies on optimal control of both batch and continuous granulation processes. The objective of steady state optimisation is to minimise the recycle rate with minimum cost for continuous processes. It has been identified that the drum rotation-rate, bed depth (material charge), and moisture content of solids are practical decision (design) parameters for system optimisation. The objective for the optimal control of batch granulation processes is to maximize the mass of product-sized particles with minimum time and binder consumption. The objective for the optimal control of the continuous process is to drive the process from one steady state to another in a minimum time with minimum binder consumption, which is also known as the state-driving problem. It has been known for some time that the binder spray-rate is the most effective control (manipulative) variable. Although other possible manipulative variables, such as feed flow-rate and additional powder flow-rate have been investigated in the complete research project, only the single input problem with the binder spray rate as the manipulative variable is addressed in the paper to demonstrate the methodology. It can be shown from simulation results that the proposed models are suitable for control and optimisation studies, and the optimisation algorithms connected with either steady state or dynamic models are successful for the determination of optimal operational conditions and dynamic trajectories with good convergence properties. (c) 2005 Elsevier Ltd. All rights reserved.

Identification of MIMO Hammerstein systems using cardinal spline functions

A new approach to identify multivariable Hammerstein systems is proposed in this paper. By using cardinal cubic spline functions to model the static nonlinearities, the proposed method is effective in modelling processes with hard and/or coupled nonlinearities. With an appropriate transformation, the nonlinear models are parameterized such that the nonlinear identification problem is converted into a linear one. The persistently exciting condition for the transformed input is derived to ensure the estimates are consistent with the true system. A simulation study is performed to demonstrate the effectiveness of the proposed method compared with the existing approaches based on polynomials. (C) 2006 Elsevier Ltd. All rights reserved.

The in-vitro bioactivity of mesoporous bioactive glasses

Ordered mesoporous bioactive glasses (MBGs) with different compositions were prepared by using nonionic block copolymer surfactants as structure-directing agents through an evaporation-induced self-assembly process. Their in-vitro bioactivities were studied in detail by electron microscopy, Fourier-transform infrared spectroscopy, and inductively coupled plasma (ICP) atomic emission spectroscopy. The ICP element analysis results were further calculated in terms of the total consumption of Ca and P, Delta[Ca]/Delta[P] ratios, and ionic activity product (IP) of hydroxyapatite. Through the above analysis, it is clear that MBGs show a different structure-bioactivity correlation compared to conventional sol-gel-derivcd BGs. The in vitro bioactivity of MBGs is dependent on the Si/Ca ratio in the network when the other material parameters such as the mesostructure and texture properties (pore size, pore volume) are controlled. MBG 80S15C with relatively lower calcium content exhibits the best in vitro bioactivity, in contrast to conventional sol-gel-derived BGs where usually higher calcium percentage BGs (e.g. 60S35C) show better bioactivity. Calcination temperature is another important factor that influences the in vitro bioactivity. According to our results, MBGs calcined at 973 K may possess the best in vitro bioactivity. The influences of the composition and calcination temperature upon bioactivity are explained in terms of the unique structures of MBGs. (c) 2006 Elsevier Ltd. All rights reserved.

Using two dimensional sectional distributions to infer three dimensional volumetric distributions - Validation using tomography

The critical process parameter for mineral separation is the degree of mineral liberation achieved by comminution. The degree of liberation provides an upper limit of efficiency for any physical separation process. The standard approach to measuring mineral liberation uses mineralogical analysis based two-dimensional sections of particles which may be acquired using a scanning electron microscope and back-scatter electron analysis or from an analysis of an image acquired using an optical microscope. Over the last 100 years, mathematical techniques have been developed to use this two dimensional information to infer three-dimensional information about the particles. For mineral processing, a particle that contains more than one mineral (a composite particle) may appear to be liberated (contain only one mineral) when analysed using only its revealed particle section. The mathematical techniques used to interpret three-dimensional information belong, to a branch of mathematics called stereology. However methods to obtain the full mineral liberation distribution of particles from particle sections are relatively new. To verify these adjustment methods, we require an experimental method which can accurately measure both sectional and three dimensional properties. Micro Cone Beam Tomography provides such a method for suitable particles and hence, provides a way to validate methods used to convert two-dimensional measurements to three dimensional estimates. For this study ore particles from a well-characterised sample were subjected to conventional mineralogical analysis (using particle sections) to estimate three-dimensional properties of the particles. A subset of these particles was analysed using a micro-cone beam tomograph. This paper presents a comparison of the three-dimensional properties predicted from measured two-dimensional sections with the measured three-dimensional properties.

Stem cells in the periodontal ligament

The ability to identify and manipulate stem cells has been a significant advancement in regenerative medicine and has contributed to the development of tissue engineering-based clinical therapies. Difficulties associated with achieving predictable periodontal regeneration, means that novel techniques such as tissue engineering need to be developed in order to regenerate the extensive soft and hard tissue destruction that results from periodontitis. One of the critical requirements for a tissue engineering approach is the delivery of ex vivo expanded progenitor populations or the mobilization of endogenous progenitor cells capable of proliferating and differentiating into the required tissues. By definition, stem cells fulfill these requirements and the recent identification of stem cells within the periodontal ligament represents a significant development in the progress toward predictable periodontal regeneration. In order to explore the importance of stem cells in periodontal wound healing and regeneration, this review will examine contemporary concepts in stem cell biology, the role of periodontal ligament progenitor cells in the regenerative process, recent developments in identifying periodontal stem cells and the clinical implications of these findings.

The in vitro effect of different PRP concentrations on osteoblasts and fibroblasts

Objectives:The aim of this study was to assess the biological rationale for the use of platelet-rich plasma (PRP) by evaluating the effect of different concentrations of PRP on osteoblasts (OB) and fibroblasts (FB) function in vitro. Materials and methods:PRP was obtained from volunteer donors using standard protocols. Primary human cultures of oral FBs and OBs were exposed to both activated and non-activated plasma as well as various concentrations of PRP (2.5 x, 3.5 x and max (4.2-5.5 x)). Cell proliferation was evaluated after 24 and 72 h using an MTT proliferation assay. Production of osteocalcin (OCN), osteoprotegerin (OPG) and transforming growth factor beta 1 (TGF-beta 1) was evaluated in OB after 24 and 72 h. Statistical analysis was performed using one-way ANOVA. Results:PRP-stimulated cell proliferation in both OBs and FBs. The effect of different PRP concentrations on cell proliferation was most notable at 72 h. The maximum effect was achieved with a concentration of 2.5 x, with higher concentrations resulting in a reduction of cell proliferation. Upregulation of OCN levels and downregulation of OPG levels were noted with increasing PRP concentrations at both 24 and 72 h. TGF-beta 1 levels were stimulated by increasing concentrations of PRP, with the increased levels being maintained at 72 h. Conclusions:PRP preparations exert a dose-specific effect on oral FBs and OBs. Optimal results were observed at a platelet concentration of 2.5 x, which was approximately half of the maximal concentrate that could be obtained. Increased concentrations resulted in a reduction in proliferation and a suboptimal effect on OB function. Hence, different PRP concentrations may have an impact on the results that can be obtained in vivo.

Applicability of experience from laboratory reactors with biological phosphorus removal in full-scale plants

Enhanced biological phosphorus removal (EBPR) has been used at many wastewater treatment plants all over the world for many years. In this study a full-scale sludge with good EBPR was tested with P-release batch tests and combined FISH/MAR (fluorescence in situ hybridisation and microautoradiography). Proposed models of PAOs and GAOs (polyphosphate- and glycogen-accumulating organisms) and microbial methods suggested from studies of laboratory reactors were found to be applicable also on sludge from full-scale plants. Dependency of pH and the uptake of both acetate and propionate were studied and used for calculations for verifying the models and results from microbial methods. All rates found from the batch tests with acetate were higher than in the batch tests with propionate, which was explained by the finding that only those parts of the bacterial community that were able to take up acetate anaerobically were able to take up propionate anaerobically.

Between-tree variation in fruit quality and fruit mineral concentrations of Hass avocados

Inconsistent internal fruit quality in Hass avocados affects consumer confidence. To determine the influence of individual trees on fruit quality, Hass avocado fruit were harvested from adjacent trees of similar external appearance in 3 commercial orchards in 1998 and 1 orchard in 1999. The trees in each orchard were grown with similar commercial practices and in similar soil types. Within each location, there were significant (P < 0.05) differences in the mean ripe fruit quality between trees with respect to fruit body rot severity ( mainly anthracnose) with and without cold storage, internal disorders severity due to diffuse discolouration and vascular browning ( after cold storage), days to ripen, percentage dry matter, and the percentage of the skin area with purple-black colour when ripe. These effects were also noted in the same orchard in 1999. There were significant (P < 0.05) differences in fruit flesh calcium, magnesium, potassium, boron and zinc concentrations between trees. Significant (P < 0.05) correlations were observed between average fruit mineral concentrations in each tree ( particularly calcium, magnesium and potassium) and body rot severity, percentage dry matter and fruit mass. There was little conclusive evidence that characteristics such as the growth of the non-suberised roots or the degree of scion under- or overgrowth was involved in these tree effects; however, differences between trees with respect to other rootstock characteristics may be involved. The inconsistency of the correlations across sites and years suggested that other factors apart from tree influences could also affect the relationship between fruit minerals and fruit quality.