Pockels effect in GaN/Al-x,Gal(1-x)N superlattice with different quantum structures - art. no. 69841G

The linear electro-optic (Pockels) effect of wurtzite gallium nitride (GaN) films and six-period GaN/AlxGa1-xN superlattices with different quantum structures were demonstrated by a polarization-maintaining fiber-optical Mach-Zehnder interferometer system with an incident light wavelength of 1.55 mu m. The samples were prepared on (0001) sapphire substrate by low-temperature metalorganic chemical vapor deposition (MOCVD). The measured coefficients of the GaN/AlxGa1-xN superlattices are much larger than those of bulk material. Taking advantage of the strong field localization due to resonances, GaN/AlxGa1-xN SL can be proposed to engineer the nonlinear responses.

Tunneling magnetoresistance in (Ga,Mn)As/Al-O/CoFeB hybrid structures

Tunneling magnetoresistance (TMR) in Ga(0.9)2Mn(0.08)As/Al-O/Co40Fe40B20 trilayer hybrid structure as a function of temperature from 10 to 50 K with magnetic field vertical bar H vertical bar <= 2000 Oe has been studied. TMR ratio of 1.6% at low fields at 10 K was achieved with the applied current of 1 mu A. The behavior of junction resistance was well explained by the tunneling resistance across the barrier. Strong bias dependences of magnetoresistance and junction resistance were presented. (C) 2009 American Institute of Physics. [DOI: 10.1063/1.3068418]

Influence of Al content on electrical and structural properties of Si-doped AlxGa1-xN/GaN HEMT structures

Improved electrical properties of AlxGa1-xN/GaN high electron mobility transistor (HEMT) structures grown by metalorganic chemical vapor deposition (MOCVD) were achieved through increasing the Al mole fraction in the AlGaN barrier layers. An average sheet resistance of 326.6 Omega/sq and a good resistance uniformity of 98% were obtained for a 2-inch Al0.38Ga0 62N/GaN HEMT structure. The surface morphology of AlxGa1-xN/GaN HEMT structures strongly correlates with the Al content. More defects were formed with increasing Al content due to the increase of tensile strain, which limits further reduction of the sheet resistance. (c) 2006 WILEY-VCH Verlag GmbH & Co KGaA, Weinheim.

Intense room temperature near infrared emission from Al (3+) and Yb3+ ions

Intense near infrared emission was observed from Al3+ and Yb3+ ions co-implanted SiO2 film on silicon. It was found that the addition of Al3+ ions could remarkably improve the photoluminescence efficiency of Yb3+-implanted SiO2 film. No excitation power saturation was observed and trivial temperature quenching factor of 2 was achieved.

Study on the hydrolysis/precipitation behavior of Keggin Al-13 and Al-30 polymers in polyaluminum solutions

The hydrolysis/precipitation behaviors of Al3+, Al-13 and Al-30 under conditions typical for flocculation in water treatment were investigated by studying the particulates' size development, charge characteristics, chemical species and speciation transformation of coagulant hydrolysis precipitates. The optimal pH conditions for hydrolysis precipitates formation for AlCl3, PAC(A113) and PAC(A130) were 6.5-7.5, 8.5-9.5, and 7.5-9.5, respectively. The precipitates' formation rate increased with the increase in dosage, and the relative rates were AlCl3 >> PAC(A130) > PACA113. The precipitates' size increased when the dosage increased from 50 mu M to 200 mu M, but it decreased when the dosage increased to 800 AM. The Zeta potential of coagulant hydrolysis precipitates decreased with the increase in pH for the three coagulants. The isoelectric points of the freshly formed precipitates for AlCl3, PAC(A113) and PAC(A130) were 7.3, 9.6 and 9.2, respectively. The Zeta potentials of AlCl3 hydrolysis precipitates were lower than those of PAC(A113) and PAC(A130) when pH > 5.0. The Zeta potential of PAC(A130) hydrolysis precipitates was higher than that of PACA113 at the acidic side, but lower at the alkaline side. The dosage had no obvious effect on the Zeta potential of hydrolysis precipitates under fixed pH conditions. The increase in Zeta potential with the increase in dosage under uncontrolled pH conditions was due to the pH depression caused by coagulant addition. Al-Ferron research indicated that the hydrolysis precipitates of AlCl3 were composed of amorphous AI(OH)3 precipitates, but those of PACA113 and PACA130 were composed of aggregates of Al-13 and Al-30, respectively. Al3+ was the most un-stable species in coagulants, and its hydrolysis was remarkably influenced by solution pH. Al-13 and Al-30 species were very stable, and solution pH and aging had little effect on the chemical species of their hydrolysis products. The research method involving coagulant hydrolysis precipitates based on Al-Ferron reaction kinetics was studied in detail. The Al species classification based on complex reaction kinetic of hydrolysis precipitates and Ferron reagent was different from that measured in a conventional coagulant assay using the Al--Ferron method. The chemical composition of Al-a, Al-b and Al-c depended on coagulant and solution pH. The Al-b measured in the current case was different from Keggin Al-13, and the high Alb content in the AlCl3 hydrolysis precipitates could not used as testimony that most of the Al3+ Was converted to highly charged Al-13 species during AlCl3 coagulation.

On the acid-base stability of Keggin Al-13 and Al-30 polymers in polyaluminum coagulants

The acid-base stabilities of Al-13 and Al-30 in polyaluminum coagulants during aging and after dosing into water were studied systematically using batch and flow-through acid-base titration experiments. The acid decomposition rates of both Al-13 and Al-30 increase rapidly with the decrease in solution pH. The acid decompositions of Al-13 and Al-30 with respect to H+ concentration are composed of two parallel first-order and second-order reactions, and the reaction orders are 1.169 and 1.005, respectively. The acid decomposition rates of Al-13 and Al-30 increase slightly when the temperature increases from 20 to ca. 35 A degrees C, but decrease when the temperature increases further. Al-30 is more stable than Al-13 in acidic solution, and the stability difference increases as the pH decreases. Al-30 is more possible to become the dominant species in polyaluminum coagulants than Al-13. The acid catalyzed decomposition and followed by recrystallization to form bayerite is one of the main processes that are responsible for the decrease of Al-13 and Al-30 in polyaluminum coagulants during storage. The deprotonation and polymerization of Al-13 and Al-30 depend on solution pH. The hydrolysis products are positively charged, and consist mainly of repeated Al-13 and Al-30 units rather than amorphous Al(OH)(3) precipitates. Al-30 is less stable than Al-13 upon alkaline hydrolysis. Al-13 is stable at pH < 5.9, while Al-30 lose one proton at the pH 4.6-5.75. Al-13 and Al-30 lose respective 5 and 10 protons and form [Al-13] (n) and [Al-30] (n) clusters within the pH region of 5.9-6.25 and 5.75-6.65, respectively. This indicates that Al-30 is easier to aggregate than Al-13 at the acidic side, but [Al-13] (n) is much easier to convert to Alsol-gel than [Al-30] (n) . Al-30 possesses better characteristics than Al-13 when used as coagulant because the hydrolysis products of Al-30 possess higher charges than that of Al-13, and [Al-30] (n) clusters exist within a wider pH range.

Mg-Al-Mn-RE系合金组织与性能研究

利用金属型铸造制备了Mg-5Al-0.3Mn-xRE (x = 0~4, wt%，RE = Ce, Nd, Sm, Y和(CeLa)混合稀土)系列合金，研究了铸态合金的组织和力学性能。利用轧制和挤压技术对优化出的合金进行了变形加工处理，并研究了合金加工后的组织和力学性能。 对于铸态合金，稀土元素不仅可以细化合金的晶粒，而且形成不同类型的Al-RE化合物，含Ce的合金中生成Al11Ce3相，含Nd或Sm的合金中，主要生成Al11Nd3 (Al11Sm3)相和少量的Al2Nd (Al2Sm)相，含Y的合金中生成Al2Y相。另外，添加稀土可以改变Mg17Al12相的形貌，使其变得更加细小、弥散。添加适量的稀土可以明显提高铸态合金在室温和150℃下的力学性能，Mg-5Al-0.3Mn-1.5Ce, Mg-5Al-0.3Mn-2Nd和Mg-5Al-0.3Mn-2Sm合金在各自的体系中具有最佳的综合力学性能。合金力学性能提高的主要原因是细晶强化、Al-RE化合物第二相强化以及减弱Mg17Al12相对合金高温力学性能的不利影响。 对Mg-5Al-0.3Mn-(1.0, 1.5, 2.0)Ce，Mg-5Al-0.3Mn-2Nd，Mg-5Al-0.3Mn-1.5(CeLa)和Mg-5Al-0.3Mn-3Y合金在300-400℃下进行了热轧制或挤压变形，与铸态合金相比，轧制和挤压合金具有更高的力学性能。轧制合金的室温抗拉强度为290-340 MPa，较铸态合金提高约50％，屈服强度约为210-260 MPa，较铸态合金提高约2倍。挤压态合金的抗拉强度为260-270 MPa，屈服强度为160-190MPa，伸长率为20-22％；150℃的力学性能也得到了明显改善。 结合热力学计算、合金化元素之间的电负性差、化合物相的生成焓数据以及相图计算，阐述了稀土化合物相的生成机制，稀土元素与Al元素之间的电负性差大于其与Mg之间的电负性差，且Al-RE相的生成焓远低于Mg-RE和Mg-Al相的生成焓，因此在Mg-Al合金中加入RE后，RE优先与Al形成Al-RE化合物。从晶粒细化、化合物强化相的生成和演变、变形加工处理的位错交互作用等方面讨论了合金的强化机制，认为细晶强化、第二相强化及形变强化是提高合金力学性能的主要机制。

用电动势方法测定Pr-Al、Nd-Al体系的热力学性质和Nd-Al合金组成

本文测定了如下电池 Pr(固)|KCl-NaCl+2%PrCl_3|Pr-Al(X_(Pr) = 0.09-0.19) Pr-Al(X_(Pr) = 0.09-0.19)|KCl-NaCl+2% PrCl_3|Pr-Al(待测) Nd(固)|KCl-NaCl+2%NdCl_3|Nd-Al(X_(Nd) = 0.09-0.19) Nd-Al(X_(Nd) = 0.09-0.19)|KCl-NaCl+2%NdCl_3|Nd-Al(待测)的电动势与温度，待测合金组成的关系。温度范围是670－850 ℃，组成范围是Pr或Nd的摩尔分数从0.01到0.190。在此基础上计算了Pr-Al、Nd-Al合金熔体中各金属的活度、偏摩尔自由能、偏摩尔熵以及合金体系的摩尔混自由能、摩尔混合熵和摩尔混合焓，计算了合金相图的部分液相线温度和不同温度下PrAl_4、NdAl_4的标准生成自由能。在空气和氯气混合气氛下对电池Nd-Al(X_(dd) = 0.09-0.19)|KCl-NaCl+NdCl_3|Nd-Al(待测)的电动势与待测合金组成、电解质中NdCl_3含量的关系进行了探讨。为在电解Nd-Al合金过程中快速、近似分析合金组成提供了依据。在此基础上提出了一种快速、近似的分析方法。

熔盐电解法制备Al-Li合金的应用基础研究及其工艺初探

Al-Li合金是近年发展起来的新型航空材料，具有低密度、高强度的特点。目前世界上正就如何进一步提高其断裂韧性，使Al-Li合金尽早走出实验室，获得实际用进行广泛，深入的研究。熔盐电解法就是在这种情况下发展起来的。虽然此法现在尚处于研究的初级阶段，但已以其能够在较简单的设备上制备低Na高纯Al-Li合金的特点受到广泛的重视，是一种很有前途的发展方向。针对我国的技术、设备现状，在参考国外研究结果的基础上，采用熔盐电解法制备Al-Li母合金 → 应用合金的制备方法是可以尽快赶上世界发步伐的有效途径。因此，本文作为整个熔盐电解制备Al-Li合金系统研究的一部分，针对目前在此领域中很多应用基础问题，诸如：作为新的电解体系正在探索中的LiCl-KCl-LiF三元相图，Li在液体Al阴极中的扩散系数，利用熔盐电解法制备低Na高纯Al-Li合金的热力学基础及如何克服LiCl强烈的吸水性给电解工艺带来的种种不便等均未得到系统研究的现状，设计完成了一系列有关熔盐电化学和热力学实验，填补了本领域的一些研究空白，并为进一步系统研究工艺条件提供了重要的参考数据。1．用NH_4Cl氯化Li_2CO_3的研究 根据热力学从理论上论证了在200 ℃左右下述氯化反应：Li_2CO_3 + 2NN_4Cl = 2LiCl + 2NH_3~↑ + H_2O~↑ + CO_2~↑可以进行完全。利用DSC方法测定反应产物LiCl的纯度，并用离子色谱法分析反应产物中CO_3~=的含量，结果均证明：在Li_2CO_3:NH_4Cl = 1:4 (mol)时，Li_2CO_3可以定量转化为LiCl，剩余的NH_4Cl完全分解。根据热重分析结果推测NH_4Cl氯化Li_2CO_3的反应历程为：Li_2CO_3 + 2NH_4Cl = 2LiCl + 2NH_3~↑ + H_2O~↑ + CO_2~↑ NH_4Cl = HCl~↑ + NH_3~↑ 而并非是想像中的：NH_4Cl = HCl~↑ + NH_3~↑ 2HCl + Li_2CO_3 = 2LiCl + H2O~↑ + CO_2~↑利用X－射线衍射方法分析产物，结果亦说明氯化可以成功。将1:4（mol）= Li_2CO_3:NH_4Cl混合样品在差热分析反应炉中直接加热测定反应产物LiCl的溶点，并与纯LiCl样品熔点的测定结果相比较，二者完全一致。以上结果说明：不仅可用此氯化反应产物代替LiCl应用于熔盐电解制备Al-Li合金中，而且还可将其应用于LiCl体系的相图测定中。因Li_2CO_3，NH_4Cl均不吸水，极易处理，因此以上研究结果无论对于Al-Li合金的工艺研究还是其他有关LiCl体系的基础研究都是很有价值的。2．直接氯化法制备LiCl-KCl-LiF三元相图的研究。LiCl-KCl-LiF三元相图是研究此体系电解机制的重要基础。为将以上直接氯化法应用于差热分析中制作此三元体系相图，首先用直接氯化法测定了三个已知二元LiCl体系相图：LiCl－KCl；LiCl-LiF；LiCl-NaCl。与文献结果吻合很好。说明将此法应用于差热分析中制作LiCl体系相图结果是可靠的。在LiCl-KCl-LiF三元相图的测定中共做出七个垂直截面，在各截面上读出等温条件下的相界点投影到浓度三角形中，得到等温投影图。结果说明LiCl-KCl-LiF是固态完全不互溶的三元共晶体系，共有三个液－固两相区；三个液－固－固三相区；一个液－固－固－固四相区，（三元共晶平面）和一个固－固－固三相区。四相点温度为348 ℃，其组成在三相平衡线的交点处，在实验上测出近似等于：41.4KCl + 57.3LiCl + 1.3LiF (mol)。3．氯化物体系中Li~+, Na~+析出电位的比较及其去极化作用的研究。在正常电化序中，Li~+应先于Na~+析出。但在以Al作阴极电解LiCl体系时，则由于Li~+在Al上有较强的去极化作用而提前析出。这是熔盐电解法可以制备低Na，高纯Al-Li合金的基础。本文在理论上对此问题进行了较深入的研究。具体内容包括（1）。测定Li~+, Na~+在二元氯化物体系中的析出电位。通过在Al阴极，Mo阴极上二离子析出电位的比较，确认了Li~+在Al阴极上产生很强的去极化作用是能利用电解法制备低Na高纯Al-Li合金的根本原因。并为在工艺研究中选择合适的电流密度提供了参考依据。（2）．根据热力学理论推导出合金化反应产生的自由焓变化与去极化作用的关系：ΔG_x + ΔG_m = -nFΔE。揭示了产生去极化作用的原因。并根据ΔG_x（偏摩尔过剩自由焓）与合金结构的关系提出可以利用二元合金相图推测极化类型及极化大小。并根据动力学原理对温度对极化的影响提出了自己的看法。（3）．求出合金化反应的热效应，认为在一定条件下亦可利用此值作为判断去极化作用大小的标准。（4）．测定Li~+, Na~+在Al-Cu, -Al-RE合金上的析出电位。结果表明Cu，RE的存在均可加强Li~+在阴极上的去极化作用，进一步加大了Li~+, Na~+析出电位之间的差别，有利于制备更纯的Al-Li 使金。为直接生产Al-Cu-Li, Al-RE-Li三元母合金奠定了基础。（5）测定Li~+在不同组成配比的LiCl-KCl熔体中，在Al阴极上的析出电位，并求出LiCl的离子平均活度系数γ＝0.71 (T = 740 ℃), 熔体对理想状态产生负偏离。4．利用阳极计时电位法测定T＝720 ℃时Li在液体Al中的扩散系数D_(Li/Al) = 4.94 * 10~(-5)cm~2·s~(-1)，与利用Stocks-Einstan公式计算出的理论值D_(Li/Al) = 4.85 * 10~(-5)cm~2·s~(-1)吻合较好。5．在上述理论研究的基础之上进行了工艺初探，所得初步结论有：（1）．加入LiF可以提高电效。（2）．采用电流密度为1 A/cm~2时，不加搅拌亦可制备出成份均匀，含Li量为10％（w.f）的Al-Li合金。（3）．根据实验结果提出 Li在熔体中的熔解可能是影响电流效果的主要原因。